Abstract: In this paper, the application of thermal spray
coatings in high speed shafts by a revolution up to 23000 RPM
has been studied. Gas compressor shafts are worn in contact
zone with journal therefore will be undersized. Wear
mechanisms of compressor shaft were identified. The
predominant wear mechanism is abrasion wear. The worn
surface was coated by hard WC-Co cermets using high
velocity oxy fuel (HVOF) after preparation. The shafts were in
satisfactory service in 8000h period. The metallurgical and
Tribological studies has been made on the worn and coated
shaft using optical microscopy, scanning electron microscopy
(SEM) and X-ray diffraction.
Abstract: Stable bacterial polymorphism on a single limiting resource may appear if between the evolved strains metabolic interactions take place that allow the exchange of essential nutrients [8]. Towards an attempt to predict the possible outcome of longrunning evolution experiments, a network based on the metabolic capabilities of homogeneous populations of every single gene knockout strain (nodes) of the bacterium E. coli is reconstructed. Potential metabolic interactions (edges) are allowed only between strains of different metabolic capabilities. Bacterial communities are determined by finding cliques in this network. Growth of the emerged hypothetical bacterial communities is simulated by extending the metabolic flux balance analysis model of Varma et al [2] to embody heterogeneous cell population growth in a mutual environment. Results from aerobic growth on 10 different carbon sources are presented. The upper bounds of the diversity that can emerge from single-cloned populations of E. coli such as the number of strains that appears to metabolically differ from most strains (highly connected nodes), the maximum clique size as well as the number of all the possible communities are determined. Certain single gene deletions are identified to consistently participate in our hypothetical bacterial communities under most environmental conditions implying a pattern of growth-condition- invariant strains with similar metabolic effects. Moreover, evaluation of all the hypothetical bacterial communities under growth on pyruvate reveals heterogeneous populations that can exhibit superior growth performance when compared to the performance of the homogeneous wild-type population.
Abstract: This paper describes the design concepts and
implementation of a 5-Joint mechanical arm for a rescue robot named
CEO Mission II. The multi-joint arm is a five degree of freedom
mechanical arm with a four bar linkage, which can be stretched to
125 cm. long. It is controlled by a teleoperator via the user-friendly
control and monitoring GUI program. With Inverse Kinematics
principle, we developed the method to control the servo angles of all
arm joints to get the desired tip position. By clicking the determined
tip position or dragging the tip of the mechanical arm on the
computer screen to the desired target point, the robot will compute
and move its multi-joint arm to the pose as seen on the GUI screen.
The angles of each joint are calculated and sent to all joint servos
simultaneously in order to move the mechanical arm to the desired
pose at once. The operator can also use a joystick to control the
movement of this mechanical arm and the locomotion of the robot.
Many sensors are installed at the tip of this mechanical arm for
surveillance from the high level and getting the vital signs of victims
easier and faster in the urban search and rescue tasks. It works very
effectively and easy to control. This mechanical arm and its software
were developed as a part of the CEO Mission II Rescue Robot that
won the First Runner Up award and the Best Technique award from
the Thailand Rescue Robot Championship 2006. It is a low cost,
simple, but functioning 5-Jiont mechanical arm which is built from
scratch, and controlled via wireless LAN 802.11b/g. This 5-Jiont
mechanical arm hardware concept and its software can also be used
as the basic mechatronics to many real applications.
Abstract: this paper presents a novel scheme which is capable of reducing the error rate and improves the transmission performance in the asynchronous cooperative MIMO systems. A case study of image transmission is applied to prove the efficient of scheme. The linear dispersion structure is employed to accommodate the cooperative wireless communication network in the dynamic topology of structure, as well as to achieve higher throughput than conventional space–time codes based on orthogonal designs. The LDPC encoder without girth-4 and the STBC encoder with guard intervals are respectively introduced. The experiment results show that the combined coder of LDPC-STBC with guard intervals can be the good error correcting coders and BER performance in the asynchronous cooperative communication. In the case study of image transmission, the results show that in the transmission process, the image quality which is obtained by applied combined scheme is much better than it which is not applied the scheme in the asynchronous cooperative MIMO systems.
Abstract: WiMAX is defined as Worldwide Interoperability for
Microwave Access by the WiMAX Forum, formed in June 2001 to
promote conformance and interoperability of the IEEE 802.16
standard, officially known as WirelessMAN. The attractive features
of WiMAX technology are very high throughput and Broadband
Wireless Access over a long distance. A detailed simulation
environment is demonstrated with the UGS, nrtPS and ertPS service
classes for throughput, delay and packet delivery ratio for a mixed
environment of fixed and mobile WiMAX. A simple mobility aspect
is considered for the mobile WiMAX and the PMP mode of
transmission is considered in TDD mode. The Network Simulator 2
(NS-2) is the tool which is used to simulate the WiMAX network
scenario. A simple Priority Scheduler and Weighted Round Robin
Schedulers are the WiMAX schedulers used in the research work
Abstract: The aim of this study is to develop mathematical
relationships for the performance parameter brake thermal efficiency
(BTE) and emission parameter nitrogen oxides (NOx) for the various
esters of vegetable oils used as CI engine fuel. The BTE is an
important performance parameter defining the ability of engine to
utilize the energy supplied and power developed similarly it is
indication of efficiency of fuels used. The esters of cottonseed oil,
soybean oil, jatropha oil and hingan oil are prepared using
transesterification process and characterized for their physical and
main fuel properties including viscosity, density, flash point and
higher heating value using standard test methods. These esters are
tried as CI engine fuel to analyze the performance and emission
parameters in comparison to diesel. The results of the study indicate
that esters as a fuel does not differ greatly with that of diesel in
properties. The CI engine performance with esters as fuel is in line
with the diesel where as the emission parameters are reduced with the
use of esters.
The correlation developed between BTE and brake power(BP),
gross calorific value(CV), air-fuel ratio(A/F), heat carried away by
cooling water(HCW). Another equation is developed between the
NOx emission and CO, HC, smoke density (SD), exhaust gas
temperature (EGT). The equations are verified by comparing the
observed and calculated values which gives the coefficient of
correlation of 0.99 and 0.96 for the BTE and NOx equations
respectively.
Abstract: As a vital activity for companies, new product
development (NPD) is also a very risky process due to the high
uncertainty degree encountered at every development stage and the
inevitable dependence on how previous steps are successfully
accomplished. Hence, there is an apparent need to evaluate new
product initiatives systematically and make accurate decisions under
uncertainty. Another major concern is the time pressure to launch a
significant number of new products to preserve and increase the
competitive power of the company. In this work, we propose an
integrated decision-making framework based on neural networks and
fuzzy logic to make appropriate decisions and accelerate the
evaluation process. We are especially interested in the two initial
stages where new product ideas are selected (go/no go decision) and
the implementation order of the corresponding projects are
determined. We show that this two-staged intelligent approach allows
practitioners to roughly and quickly separate good and bad product
ideas by making use of previous experiences, and then, analyze a
more shortened list rigorously.
Abstract: Natural gas usually includes H2S component which is
very toxic, hazardous and corrosive to environment, human being and
process equipments, respectively. Therefore, sweetening of the gas
(separation of H2S) is inevitable. To achieve this purpose, using
packed-bed columns with liquid absorbents such as MEA or DEA is
very common. Due to some problems of usual packed columns
especially high pressure drop of gas phase, a novel kind of them
called wetted-wire column (WWC) has been invented. The column
decreases the pressure drop significantly and improves the absorption
efficiency. The packings are very thin rods (like wire) and as long as
column. The column has 100 wires with a triangular arrangement and
counter current flows of gas and liquid phases. The observation
showed that at the same conditions, the absorption performance was
quite comparable to conventional packed-bed towers and a very low
pressure drop.
Abstract: Designing and implementing intelligent systems has become a crucial factor for the innovation and development of better products of space technologies. A neural network is a parallel system, capable of resolving paradigms that linear computing cannot. Field programmable gate array (FPGA) is a digital device that owns reprogrammable properties and robust flexibility. For the neural network based instrument prototype in real time application, conventional specific VLSI neural chip design suffers the limitation in time and cost. With low precision artificial neural network design, FPGAs have higher speed and smaller size for real time application than the VLSI and DSP chips. So, many researchers have made great efforts on the realization of neural network (NN) using FPGA technique. In this paper, an introduction of ANN and FPGA technique are briefly shown. Also, Hardware Description Language (VHDL) code has been proposed to implement ANNs as well as to present simulation results with floating point arithmetic. Synthesis results for ANN controller are developed using Precision RTL. Proposed VHDL implementation creates a flexible, fast method and high degree of parallelism for implementing ANN. The implementation of multi-layer NN using lookup table LUT reduces the resource utilization for implementation and time for execution.
Abstract: This paper details a new concept of using compressed air as a potential zero pollution power source for motorbikes. In place of an internal combustion engine, the motorbike is equipped with an air turbine transforms the energy of the compressed air into shaft work. The mathematical modeling and performance evaluation of a small capacity compressed air driven vaned type novel air turbine is presented in this paper. The effect of isobaric admission and adiabatic expansion of high pressure air for different rotor diameters, casing diameters and ratio of rotor to casing diameters of the turbine have been considered and analyzed. It is concluded that the work output is found optimum for some typical values of rotor / casing diameter ratios. In this study, the maximum power works out to 3.825 kW (5.20 HP) for casing diameter of 200 mm and rotor to casing diameter ratio of 0.65 to 0.60 which is sufficient to run motorbike.
Abstract: This study investigated the relationship between urban
and rural ozone concentrations and quantified the extent to which
ambient rural conditions and the concentrations of other pollutants
can be used to predict urban ozone concentrations. The study
describes the variations of ozone in weekday and weekends as well as
the daily maximum recorded at selected monitoring stations. The
results showed that Putrajaya station had the highest concentrations
of O3 on weekend due the titration of NO during the weekday.
Additionally, Jerantut had the lowest average concentration with a
reading value high on Wednesdays. The comparisons of average and
maximum concentrations of ozone for the three stations showed that
the strongest significant correlation is recorded in Jerantut station
with the value R2= 0.769. Ozone concentrations originating from a
neighbouring urban site form a better predictor to the urban ozone
concentrations than widespread rural ozone at some levels of
temporal averaging. It is found that in urban and rural of Malaysian
peninsular, the concentration of ozone depends on the concentration
of NOx and seasonal meteorological factors. The HYSPLIT Model
(the northeast monsoon) showed that the wind direction can also
influence the concentration of ozone in the atmosphere in the studied
areas.
Abstract: In this work, we present a comparison between
different techniques of image compression. First, the image is
divided in blocks which are organized according to a certain scan.
Later, several compression techniques are applied, combined or
alone. Such techniques are: wavelets (Haar's basis), Karhunen-Loève
Transform, etc. Simulations show that the combined versions are the
best, with minor Mean Squared Error (MSE), and higher Peak Signal
to Noise Ratio (PSNR) and better image quality, even in the presence
of noise.
Abstract: The purposes of this study are 1) to identify
learning styles of university students in Bangkok, and 2) to study
the frequency of the relevant instructional context of the identified
learning styles. Learning Styles employed in this study are those of
Honey and Mumford, which include 1) Reflectors, 2) Theorists, 3)
Pragmatists, and 4) Activists. The population comprises 1383
students and 5 lecturers. Research tools are 2 questionnaires – one
used for identifying students- learning styles, and the other used for
identifying the frequency of the relevant instructional context of
the identified learning styles.
The research findings reveal that 32.30 percent - are Activists,
while 28.10 percent are Theorists, 20.10 are Reflectors, and 19.50
are Pragmatists. In terms of the relevant instructional context of the
identified 4 learning styles, it is found that the frequency level of
the instructional context is totally in high level. Moreover, 2 lists of
the context being conducted most frequently are 'Lead'in activity
to review background knowledge,- and 'Information retrieval
report.' And these two activities serve the learning styles of
theorists and activists. It is, therefore, suggested that more
instructional context supporting the activists, the majority of the
population, learning best by doing, as well as emotional learning
situation should be added.
Abstract: A hybrid learning automata-genetic algorithm (HLGA) is proposed to solve QoS routing optimization problem of next generation networks. The algorithm complements the advantages of the learning Automato Algorithm(LA) and Genetic Algorithm(GA). It firstly uses the good global search capability of LA to generate initial population needed by GA, then it uses GA to improve the Quality of Service(QoS) and acquiring the optimization tree through new algorithms for crossover and mutation operators which are an NP-Complete problem. In the proposed algorithm, the connectivity matrix of edges is used for genotype representation. Some novel heuristics are also proposed for mutation, crossover, and creation of random individuals. We evaluate the performance and efficiency of the proposed HLGA-based algorithm in comparison with other existing heuristic and GA-based algorithms by the result of simulation. Simulation results demonstrate that this paper proposed algorithm not only has the fast calculating speed and high accuracy but also can improve the efficiency in Next Generation Networks QoS routing. The proposed algorithm has overcome all of the previous algorithms in the literature.
Abstract: Today, people are more interested in the foods
beneficial on their health. However, there are still lacks of accurate
knowledge in the field of biological properties, functional properties,
including the application of legume in foods. This study focused on
antioxidant activity of soybean (SB) and fermented soybean (FSB)
crude extracts evaluating to have more information in fortification SB
and FSB crude extracts in food products and/or dietary supplement.
SB and FSB crude extracts were prepared by infusion with water and
ethanol. The antioxidant activity of crude extracts was studied with
DPPH and ABTS assay including commercial standard. From both
DPPH and ABTS assay, the antioxidant activity of SB and FSB water
crude extract showed higher antioxidant activity than ethanol crude
extract, and FSB crude extract showed higher antioxidant activity
than SB crude extract. In DPPH assay, BHT and vitamin C showed
IC50 values at 0.241, 0.039 mg/ml, in ABTS assay. In addition,
Trolox showed IC50 at 0.058 mg/ml respectively. FSB water crude
extract showed high antioxidant activity. Finally, the functional
properties study of both water and ethanol crude extracts should be
done for beneficial in application of these extracts in food products
and dietary supplement in the near future.
Abstract: The use of Inverse Discrete Fourier Transform (IDFT) implemented in the form of Inverse Fourier Transform (IFFT) is one of the standard method of reconstructing Magnetic Resonance Imaging (MRI) from uniformly sampled K-space data. In this tutorial, three of the major problems associated with the use of IFFT in MRI reconstruction are highlighted. The tutorial also gives brief introduction to MRI physics; MRI system from instrumentation point of view; K-space signal and the process of IDFT and IFFT for One and two dimensional (1D and 2D) data.
Abstract: Functional gastrointestinal disorders affect millions of people spread all age regardless of race and sex. There are, however, rare diagnostic methods for the functional gastrointestinal disorders because functional disorders show no evidence of organic and physical causes. Our research group identified recently that the gastrointestinal tract well in the patients with the functional gastrointestinal disorders becomes more rigid than healthy people when palpating the abdominal regions overlaying the gastrointestinal tract. Aim of this study is, therefore, to develop a diagnostic system for the functional gastrointestinal disorders based on ultrasound technique, which can quantify the characteristic above related to the rigidity of the gastrointestinal tract well. Ultrasound system was designed. The system consisted of transmitter, ultrasonic transducer, receiver, TGC, and CPLD, and verified via a phantom test. For the phantom test, ten soft-tissue specimens were harvested from porcine. Five of them were then treated chemically to mimic a rigid condition of gastrointestinal tract well, which was induced by functional gastrointestinal disorders. Additionally, the specimens were tested mechanically to identify if the mimic was reasonable. The customized ultrasound system was finally verified through application to human subjects with/without functional gastrointestinal disorders (Normal and Patient Groups). It was identified from the mechanical test that the chemically treated specimens were more rigid than normal specimen. This finding was favorably compared with the result obtained from the phantom test. The phantom test also showed that ultrasound system well described the specimen geometric characteristics and detected an alteration in the specimens. The maximum amplitude of the ultrasonic reflective signal in the rigid specimens (0.2±0.1Vp-p) at the interface between the fat and muscle layers was explicitly higher than that in the normal specimens (0.1±0.0Vp-p). Clinical tests using our customized ultrasound system for human subject showed that the maximum amplitudes of the ultrasonic reflective signals near to the gastrointestinal tract well for the patient group (2.6±0.3Vp-p) were generally higher than those in normal group (0.1±0.2Vp-p). Here, maximum reflective signals was appeared at 20mm depth approximately from abdominal skin for all human subjects, corresponding to the location of the boundary layer close to gastrointestinal tract well. These results suggest that newly designed diagnostic system based on ultrasound technique may diagnose enough the functional gastrointestinal disorders.
Abstract: In this paper, applying He-s energy balance method to determine frequency formulation relations of nonlinear oscillators with discontinuous term or fractional potential. By calculation and computer simulations, compared with the exact solutions show that the results obtained are of high accuracy.
Abstract: Detection of player identity is challenging task in sport video content analysis. In case of soccer video player number recognition is effective and precise solution. Jersey numbers can be considered as scene text and difficulties in localization and recognition appear due to variations in orientation, size, illumination, motion etc. This paper proposed new method for player number localization and recognition. By observing hue, saturation and value for 50 different jersey examples we noticed that most often combination of low and high saturated pixels is used to separate number and jersey region. Image segmentation method based on this observation is introduced. Then, novel method for player number localization based on internal contours is proposed. False number candidates are filtered using area and aspect ratio. Before OCR processing extracted numbers are enhanced using image smoothing and rotation normalization.
Abstract: Whit the increasing of traffic, noise emanated from
motor vehicles increases as well, which subsequently causes adding
to the stress of modern city. Thus, it is needed to look for most
critical areas in terms of environmental and social impact of noise.
There are several critical situations for noise emanated from motor
vehicles such as stop and go situation which usually occurs near
junctions or at-grade intersections. This study was conducted in two
locations, most common types of intersections, crossroads and Tjunctions.
The highest average noise levels are recorded during Go
phase for T-junction, 64.4 dB, and Drive phase for crossroad, 64 dB.
It implies that the existence of intersection caused the noise level to
increase. The vehicles starting to move produce more sound than
when they travel at a constant speed along the intersection. It is
suggested that special considerations and priority of allocating funds
should be given to these critical spots.