Abstract: The main focus of the work was concerned with hydrodynamic and thermal analysis of the plate heat exchanger channel with corrugation patterns suggested to be triangular, sinusoidal, and square corrugation. This study was to numerically model and validate the triangular corrugated channel with dimensions/parameters taken from open literature, and then model/analyze both sinusoidal, and square corrugated channel referred to the triangular model. Initially, 2D modeling with local extensive analysis for triangular corrugated channel was carried out. By that, all local pressure drop, wall shear stress, friction factor, static temperature, heat flux, Nusselt number, and surface heat coefficient, were analyzed to interpret the hydrodynamic and thermal phenomena occurred in the flow. Furthermore, in order to facilitate confidence in this model, a comparison between the values predicted, and experimental results taken from literature for almost the same case, was done. Moreover, a holistic numerical study for sinusoidal and square channels together with global comparisons with triangular corrugation under the same condition, were handled. Later, a comparison between electric, and fluid cooling through varying the boundary condition was achieved. The constant wall temperature and constant wall heat flux boundary conditions were employed, and the different resulted Nusselt numbers as a consequence were justified. The results obtained can be used to come up with an optimal design, a 'compromise' between heat transfer and pressure drop.
Abstract: In this work, we apply the Modified Laplace
decomposition algorithm in finding a numerical solution of Blasius’
boundary layer equation for the flat plate in a uniform stream. The
series solution is found by first applying the Laplace transform to the
differential equation and then decomposing the nonlinear term by the
use of Adomian polynomials. The resulting series, which is exactly the
same as that obtained by Weyl 1942a, was expressed as a rational
function by the use of diagonal padé approximant.
Abstract: The operation performance of a valveless micro-pump
is strongly dependent on the shape of connected nozzle/diffuser and
Reynolds number. The aims of present work are to compare the
performance curves of micropump with the original straight
nozzle/diffuser and contoured nozzle/diffuser under different back
pressure conditions. The tested valveless micropumps are assembled
of five pieces of patterned PMMA plates with hot-embracing
technique. The structures of central chamber, the inlet/outlet
reservoirs and the connected nozzle/diffuser are fabricated with laser
cutting machine. The micropump is actuated with circular-type PZT
film embraced on the bottom of central chamber. The deformation of
PZT membrane with various input voltages is measured with a
displacement laser probe. A simple testing facility is also constructed
to evaluate the performance curves for comparison.
In order to observe the evaluation of low Reynolds number
multiple vortex flow patterns within the micropump during suction
and pumping modes, the unsteady, incompressible laminar
three-dimensional Reynolds-averaged Navier-Stokes equations are
solved. The working fluid is DI water with constant thermo-physical
properties. The oscillating behavior of PZT film is modeled with the
moving boundary wall in way of UDF program. With the dynamic
mesh method, the instants pressure and velocity fields are obtained
and discussed.Results indicated that the volume flow rate is not
monotony increased with the oscillating frequency of PZT film,
regardless of the shapes of nozzle/diffuser. The present micropump
can generate the maximum volume flow rate of 13.53 ml/min when
the operation frequency is 64Hz and the input voltage is 140 volts.
The micropump with contoured nozzle/diffuser can provide 7ml/min
flow rate even when the back pressure is up to 400 mm-H2O. CFD
results revealed that the flow central chamber was occupied with
multiple pairs of counter-rotating vortices during suction and
pumping modes. The net volume flow rate over a complete
oscillating periodic of PZT
Abstract: Grid composite structures have many applications in aerospace industry in which deal with transverse loadings abundantly. In present paper a stiffened composite cylindrical shell with clamped-free boundary condition under transverse end load experimentally and numerically was studied. Some electrical strain gauges were employed to measure the strains. Also a finite element analysis was done for validation of experimental result. The FEM software used was ANSYS11. In addition, the results between stiffened composite shell and unstiffened composite shell were compared. It was observed that intersection of two stiffeners has an important effect in decrease of stress in the shell. Fairly good agreements were observed between the numerical and the measured results. According to recent studies about grid composite structures, it should be noted that any investigation like this research has not been reported.
Abstract: In this paper, we present a new algorithm for clustering data in large datasets using image processing approaches. First the dataset is mapped into a binary image plane. The synthesized image is then processed utilizing efficient image processing techniques to cluster the data in the dataset. Henceforth, the algorithm avoids exhaustive search to identify clusters. The algorithm considers only a small set of the data that contains critical boundary information sufficient to identify contained clusters. Compared to available data clustering techniques, the proposed algorithm produces similar quality results and outperforms them in execution time and storage requirements.
Abstract: A novel PDE solver using the multidimensional wave
digital filtering (MDWDF) technique to achieve the solution of a 2D
seismic wave system is presented. In essence, the continuous physical
system served by a linear Kirchhoff circuit is transformed to an
equivalent discrete dynamic system implemented by a MD wave
digital filtering (MDWDF) circuit. This amounts to numerically
approximating the differential equations used to describe elements of a
MD passive electronic circuit by a grid-based difference equations
implemented by the so-called state quantities within the passive
MDWDF circuit. So the digital model can track the wave field on a
dense 3D grid of points. Details about how to transform the continuous
system into a desired discrete passive system are addressed. In
addition, initial and boundary conditions are properly embedded into
the MDWDF circuit in terms of state quantities. Graphic results have
clearly demonstrated some physical effects of seismic wave (P-wave
and S–wave) propagation including radiation, reflection, and
refraction from and across the hard boundaries. Comparison between
the MDWDF technique and the finite difference time domain (FDTD)
approach is also made in terms of the computational efficiency.
Abstract: We present a system that finds road boundaries and
constructs the virtual lane based on fusion data from a laser and a
monocular sensor, and detects forward vehicle position even in no lane
markers or bad environmental conditions. When the road environment
is dark or a lot of vehicles are parked on the both sides of the road, it is
difficult to detect lane and road boundary. For this reason we use
fusion of laser and vision sensor to extract road boundary to acquire
three dimensional data. We use parabolic road model to calculate road
boundaries which is based on vehicle and sensors state parameters and
construct virtual lane. And then we distinguish vehicle position in each
lane.
Abstract: This paper considers the effect of heat generation
proportional l to (T - T∞ )p , where T is the local temperature and T∞
is the ambient temperature, in unsteady free convection flow near the
stagnation point region of a three-dimensional body. The fluid is
considered in an ambient fluid under the assumption of a step change
in the surface temperature of the body. The non-linear coupled partial
differential equations governing the free convection flow are solved
numerically using an implicit finite-difference method for different
values of the governing parameters entering these equations. The
results for the flow and heat characteristics when p ≤ 2 show that
the transition from the initial unsteady-state flow to the final steadystate
flow takes place smoothly. The behavior of the flow is seen
strongly depend on the exponent p.
Abstract: Solid fuel transient burning behavior under oxidizer
gas flow is numerically investigated. It is done using analysis of the
regression rate responses to the imposed sudden and oscillatory
variation at inflow properties. The conjugate problem is considered
by simultaneous solution of flow and solid phase governing
equations to compute the fuel regression rate. The advection
upstream splitting method is used as flow computational scheme in
finite volume method. The ignition phase is completely simulated to
obtain the exact initial condition for response analysis. The results
show that the transient burning effects which lead to the combustion
instabilities and intermittent extinctions could be observed in solid
fuels as the solid propellants.
Abstract: Analysis for the propagation of elastic waves in
arbitrary anisotropic plates is investigated, commencing with a
formal analysis of waves in a layered plate of an arbitrary anisotropic
media, the dispersion relations of elastic waves are obtained by
invoking continuity at the interface and boundary of conditions on
the surfaces of layered plate. The obtained solutions can be used for
material systems of higher symmetry such as monoclinic,
orthotropic, transversely isotropic, cubic, and isotropic as it is
contained implicitly in the analysis. The cases of free layered plate
and layered half space are considered separately. Some special cases
have also been deduced and discussed. Finally numerical solution of
the frequency equations for an aluminum epoxy is carried out, and
the dispersion curves for the few lower modes are presented. The
results obtained theoretically have been verified numerically and
illustrated graphically.
Abstract: Resins are used in nuclear power plants for water
ultrapurification. Two approaches are considered in this work:
column experiments and simulations. A software called OPTIPUR
was developed, tested and used. The approach simulates the onedimensional
reactive transport in porous medium with convectivedispersive
transport between particles and diffusive transport within
the boundary layer around the particles. The transfer limitation in the
boundary layer is characterized by the mass transfer coefficient
(MTC). The influences on MTC were measured experimentally. The
variation of the inlet concentration does not influence the MTC; on
the contrary of the Darcy velocity which influences. This is consistent
with results obtained using the correlation of Dwivedi&Upadhyay.
With the MTC, knowing the number of exchange site and the relative
affinity, OPTIPUR can simulate the column outlet concentration
versus time. Then, the duration of use of resins can be predicted in
conditions of a binary exchange.
Abstract: In the Top Right Access point Minimum Length Corridor (TRA-MLC) problem [1], a rectangular boundary partitioned into rectilinear polygons is given and the problem is to find a corridor of least total length and it must include the top right corner of the outer rectangular boundary. A corridor is a tree containing a set of line segments lying along the outer rectangular boundary and/or on the boundary of the rectilinear polygons. The corridor must contain at least one point from the boundaries of the outer rectangle and also the rectilinear polygons. Gutierrez and Gonzalez [1] proved that the MLC problem, along with some of its restricted versions and variants, are NP-complete. In this paper, we give a shorter proof of NP-Completeness of TRA-MLC by findig the reduction in the following way.
Abstract: Superplastic deformation and high temperature load
relaxation behavior of coarse-grained iron aluminides with the
composition of Fe-28 at.% Al have been investigated. A series of load
relaxation and tensile tests were conducted at temperatures ranging
from 600 to 850oC. The flow curves obtained from load relaxation
tests were found to have a sigmoidal shape and to exhibit stress vs.
strain rate data in a very wide strain rate range from 10-7/s to 10-2/s.
Tensile tests have been conducted at various initial strain rates ranging
from 3×10-5/s to 1×10-2/s. Maximum elongation of ~500 % was
obtained at the initial strain rate of 3×10-5/s and the maximum strain
rate sensitivity was found to be 0.68 at 850oC in binary Fe-28Al alloy.
Microstructure observation through the optical microscopy (OM) and
the electron back-scattered diffraction (EBSD) technique has been
carried out on the deformed specimens and it has revealed the
evidences for grain boundary migration and grain refinement to occur
during superplastic deformation, suggesting the dynamic
recrystallization mechanism. The addition of Cr by the amount of 5
at.% appeared to deteriorate the superplasticity of the binary iron
aluminide. By applying the internal variable theory of structural
superplasticity, the addition of Cr has been revealed to lower the
contribution of the frictional resistance to dislocation glide during high
temperature deformation of the Fe3Al alloy.
Abstract: There are lots of different ways to find the natural
frequencies of a rotating system. One of the most effective methods
which is used because of its precision and correctness is the
application of the transfer matrix. By use of this method the entire
continuous system is subdivided and the corresponding differential
equation can be stated in matrix form. So to analyze shaft that is this
paper issue the rotor is divided as several elements along the shaft
which each one has its own mass and moment of inertia, which this
work would create possibility of defining the named matrix. By
Choosing more elements number, the size of matrix would become
larger and as a result more accurate answers would be earned. In this
paper the dynamics of a rotor-bearing system is analyzed,
considering the gyroscopic effect. To increase the accuracy of
modeling the thickness of the disk and bearings is also taken into
account which would cause more complicated matrix to be solved.
Entering these parameters to our modeling would change the results
completely that these differences are shown in the results. As said
upper, to define transfer matrix to reach the natural frequencies of
probed system, introducing some elements would be one of the
requirements. For the boundary condition of these elements, bearings
at the end of the shaft are modeled as equivalent spring and dampers
for the discretized system. Also, continuous model is used for the
shaft in the system. By above considerations and using transfer
matrix, exact results are taken from the calculations. Results Show
that, by increasing thickness of the bearing the amplitude of vibration
would decrease, but obviously the stiffness of the shaft and the
natural frequencies of the system would accompany growth.
Consequently it is easily understood that ignoring the influences of
bearing and disk thicknesses would results not real answers.
Abstract: In this paper dynamics of a vapour bubble generated
due to a local energy input inside a vertical rigid cylinder and in the
absence of buoyancy forces is investigated. Different ratios of the
diameter of the rigid cylinder to the maximum radius of the bubble
are considered. The Boundary Integral Equation Method is employed
for numerical simulation of the problem. Results show that during
the collapse phase of the bubble inside a vertical rigid cylinder, two
liquid micro jets are developed on the top and bottom sides of the
vapour bubble and are directed inward. Results also show that
existence of a deposit rib inside the vertical rigid cylinder slightly
increases the life time of the bubble. It is found that by increasing the
ratio of the cylinder diameter to the maximum radius of the bubble,
the rate of the growth and collapse phases of the bubble increases
and the life time of the bubble decreases.
Abstract: Subgrade moisture content varies with environmental and soil conditions and has significant influence on pavement performance. Therefore, it is important to establish realistic estimates of expected subgrade moisture contents to account for the effects of this variable on predicted pavement performance during the design stage properly. The initial boundary soil suction profile for a given pavement is a critical factor in determining expected moisture variations in the subgrade for given pavement and climatic and soil conditions. Several numerical models have been developed for predicting water and solute transport in saturated and unsaturated subgrade soils. Soil hydraulic properties are required for quantitatively describing water and chemical transport processes in soils by the numerical models. The required hydraulic properties are hydraulic conductivity, water diffusivity, and specific water capacity. The objective of this paper was to determine isothermal moisture profiles in a soil fill and predict the soil moisture movement above the ground water table using a simple one-dimensional finite difference model.
Abstract: The parametrical study of Shrouded Contra-rotating
Rotor was done in this paper based on 2D axisymmetric simulations.
The calculations were made with an actuator disk as double rotor
model. It objects to explore and quantify the effects of different shroud
geometry parameters mainly using the performance of power loading
(PL), which could evaluate the whole propulsion system capability as
5 Newtontotal thrust generationfor hover demand. The numerical
results show that:The increase of nozzle radius is desired but limited
by the flow separation, its optimal design is around 1.15 times rotor
radius, the viscosity effects greatly constraint the influence of nozzle
shape, the divergent angle around 10.5° performs best for chosen
nozzle length;The parameters of inlet such as leading edge curvature,
radius and internal shape do not affect thrust great but play an
important role in pressure distribution which could produce most part
of shroud thrust, they should be chosen according to the reduction of
adverse pressure gradients to reduce the risk of boundary separation.
Abstract: This work is focused on the steady boundary layer flow
near the forward stagnation point of plane and axisymmetric bodies
towards a stretching sheet. The no slip condition on the solid
boundary is replaced by the partial slip condition. The analytical
solutions for the velocity distributions are obtained for the various
values of the ratio of free stream velocity and stretching velocity, slip
parameter, the suction and injection velocity parameter, magnetic
parameter and dimensionality index parameter in the series forms with
the help of homotopy analysis method (HAM). Convergence of the
series is explicitly discussed. Results show that the flow and the skin
friction coefficient depend heavily on the velocity slip factor. In
addition, the effects of all the parameters mentioned above were more
pronounced for plane flows than for axisymmetric flows.
Abstract: In this paper, a numerical solution based on nonpolynomial
cubic spline functions is used for finding the solution of
boundary value problems which arise from the problems of calculus
of variations. This approximation reduce the problems to an explicit
system of algebraic equations. Some numerical examples are also
given to illustrate the accuracy and applicability of the presented
method.
Abstract: The present study is concerned with effect of exciting
boundary layer on increase in heat transfer from flat surfaces. As any
increase in heat transfer between a fluid inside a face and another one
outside of it can cause an increase in some equipment's efficiency, so
at this present we have tried to increase the wall's heat transfer
coefficient by exciting the fluid boundary layer. By a collision
between flow and the placed block at the fluid way, the flow pattern
and the boundary layer stability will change. The flow way inside the
channel is simulated as a 2&3-dimensional channel by Gambit
TM
software.
With studying the achieved results by this simulation for the flow
way inside the channel with a block coordinating with Fluent
TM
software, it's determined that the figure and dimensions of the exciter
are too important for exciting the boundary layer so that any increase
in block dimensions in vertical side against the flow and any
reduction in its dimensions at the flow side can increase the average
heat transfer coefficient from flat surface and increase the flow
pressure loss. Using 2&3-dimensional analysis on exciting the flow at
the flow way inside a channel by cylindrical block at the same time
with the external flow, we came to this conclusion that the heat flux
transferred from the surface, is increased considerably in terms of the
condition without excitation. Also, the k-e turbulence model is used.