Abstract: This is a study on numerical simulation of the convection-diffusion transport of a chemical species in steady flow through a small-diameter tube, which is lined with a very thin layer made up of retentive and absorptive materials. The species may be subject to a first-order kinetic reversible phase exchange with the wall material and irreversible absorption into the tube wall. Owing to the velocity shear across the tube section, the chemical species may spread out axially along the tube at a rate much larger than that given by the molecular diffusion; this process is known as dispersion. While the long-time dispersion behavior, well described by the Taylor model, has been extensively studied in the literature, the early development of the dispersion process is by contrast much less investigated. By early development, that means a span of time, after the release of the chemical into the flow, that is shorter than or comparable to the diffusion time scale across the tube section. To understand the early development of the dispersion, the governing equations along with the reactive boundary conditions are solved numerically using the Flux Corrected Transport Algorithm (FCTA). The computation has enabled us to investigate the combined effects on the early development of the dispersion coefficient due to the reversible and irreversible wall reactions. One of the results is shown that the dispersion coefficient may approach its steady-state limit in a short time under the following conditions: (i) a high value of Damkohler number (say Da ≥ 10); (ii) a small but non-zero value of absorption rate (say Γ* ≤ 0.5).
Abstract: Li1.5Al0.5Ti1.5 (PO4)3(LATP) has received much
attention as a solid electrolyte for lithium batteries. In this study, the
LATP solid electrolyte is prepared by the co-precipitation method
using Li3PO4 as a Li source. The LATP is successfully prepared and
the Li ion conductivities of bulk (inner crystal) and total (inner crystal
and grain boundary) are 1.1 × 10-3 and 1.1 × 10-4 S cm-1, respectively.
These values are comparable to the reported values, in which Li2C2O4
is used as the Li source. It is conclude that the LATP solid electrolyte
can be prepared by the co-precipitation method using Li3PO4 as the Li
source and this procedure has an advantage in mass production over
previous procedure using Li2C2O4 because Li3PO4 is lower price
reagent compared with Li2C2O4.
Abstract: Three dimensional simulations in tube in tube heat
exchangers are investigated numerically in this study. In these
simulations forced convective heat transfer and laminar flow of
single-phase water are considered. In order to measure heat transfer
parameters in these heat exchangers, FLUENT CFD Solver is used in
this numerical method. For the purpose of creating geometry and
exert boundary and initial conditions in the present model, finite
volume method in Computational Fluid Dynamics is used in this
study. In the present study, at each Z-location, variation of local
temperatures, heat flux and Nusselt number at the whole tube is
investigated in detail. Thereafter, averaged computational Nusselt
number in this model is calculated. In addition, conceivable pressure
drops have been obtained at each Z-location in this model. Then,
pressure drop values in the present model are explored. Finally, all
the numerical results for this kind of heat exchanger will be discussed
precisely.
Abstract: A potential flow model is used to study the unsteady
flow past two airfoils in configuration, each of which is suddenly set
into motion. The airfoil bound vortices are modeled using lumped
vortex elements and the wake behind the airfoil is modeled by discrete
vortices. This consists of solving a steady state flow problem at each
time-step where unsteadiness is incorporated through the “zero normal
flow on a solid surface" boundary condition at every time instant.
Additionally, along with the “zero normal flow on a solid surface"
boundary condition Kelvin-s condition is used to compute the strength
of the latest wake vortex shed from the trailing edge of the airfoil.
Location of the wake vortices is updated at each time-step to get the
wake shape at each time instant. Results are presented to show the
effect of airfoil-airfoil interaction and airfoil-wake interaction on the
aerodynamic characteristics of each airfoil.
Abstract: In this paper we use classical linear stability theory
to investigate the effects of uniform internal heat generation on the
onset of Marangoni convection in a horizontal layer of fluid heated
from below. We use a analytical technique to obtain the close form
analytical expression for the onset of Marangoni convection when
the lower boundary is conducting with free-slip condition. We show
that the effect of increasing the internal heat generation is always to
destabilize the layer.
Abstract: In contrast to existing methods which do not take into account multiconnectivity in a broad sense of this term, we develop mathematical models and highly effective combination (BIEM and FDM) numerical methods of calculation of stationary and cvazistationary temperature field of a profile part of a blade with convective cooling (from the point of view of realization on PC). The theoretical substantiation of these methods is proved by appropriate theorems. For it, converging quadrature processes have been developed and the estimations of errors in the terms of A.Ziqmound continuity modules have been received. For visualization of profiles are used: the method of the least squares with automatic conjecture, device spline, smooth replenishment and neural nets. Boundary conditions of heat exchange are determined from the solution of the corresponding integral equations and empirical relationships. The reliability of designed methods is proved by calculation and experimental investigations heat and hydraulic characteristics of the gas turbine 1st stage nozzle blade
Abstract: This paper describes a novel optimized JTAG interface circuit between a JTAG controller and target IC. Being able to access JTAG using only one or two pins, this circuit does not change the original boundary scanning test frequency of target IC. Compared with the traditional JTAG interface which based on IEEE std. 1149.1, this reduced pin technology is more applicability in pin limited devices, and it is easier to control the scale of target IC for the designer.
Abstract: In this paper, a two-dimensional mathematical model is developed for estimating the extent of inland inundation due to Indonesian tsunami of 2004 along the coastal belts of Peninsular Malaysia and Thailand. The model consists of the shallow water equations together with open and coastal boundary conditions. In order to route the water wave towards the land, the coastal boundary is treated as a time dependent moving boundary. For computation of tsunami inundation, the initial tsunami wave is generated in the deep ocean with the strength of the Indonesian tsunami of 2004. Several numerical experiments are carried out by changing the slope of the beach to examine the extent of inundation with slope. The simulated inundation is found to decrease with the increase of the slope of the orography. Correlation between inundation / recession and run-up are found to be directly proportional to each other.
Abstract: Unsteady natural convection and heat transfer in a square cavity partially filled with porous media using a thermal
non-equilibrium model is studied in this paper. The left vertical wall is
maintained at a constant hot temperature Th and the right vertical wall
is maintained at a constant cold temperature Tc, while the horizontal
walls are adiabatic. The governing equations are obtained by applying
the Darcy model and Boussinesq approximation. COMSOL’s finite
element method is used to solve the non-dimensional governing
equations together with specified boundary conditions. The governing
parameters of this study are the Rayleigh number (Ra = 10^5, and Ra = 10^6 ), Darcy namber (Da = 10^−2, and Da = 10^−3),
the modified thermal conductivity ratio (10^−1 ≤ γ ≤ 10^4), the inter-phase heat transfer coefficien (10^−1 ≤ H ≤ 10^3) and the
time dependent (0.001 ≤ τ ≤ 0.2). The results presented for
values of the governing parameters in terms of streamlines in both
fluid/porous-layer, isotherms of fluid in fluid/porous-layer, isotherms
of solid in porous layer, and average Nusselt number.
Abstract: –In this paper the damage in clamped-free, clampedclamped and free-free beam are analyzed considering samples
without and with structural modifications. The damage location is
investigated by the use of the bispectrum and wavelet analysis. The
mathematical models are obtained using 2D elasticity theory and the
Finite Element Method (FEM). The numerical and experimental data
are approximated using the Particle Swarm Optimizer (PSO) method
and this way is possible to adjust the localization and the severity of
the damage. The experimental data are obtained through
accelerometers placed along the sample. The system is excited using
impact hammer.
Abstract: A number of automated shot-change detection
methods for indexing a video sequence to facilitate browsing and
retrieval have been proposed in recent years. This paper emphasizes
on the simulation of video shot boundary detection using one of the
methods of the color histogram wherein scaling of the histogram
metrics is an added feature. The difference between the histograms of
two consecutive frames is evaluated resulting in the metrics. Further
scaling of the metrics is performed to avoid ambiguity and to enable
the choice of apt threshold for any type of videos which involves
minor error due to flashlight, camera motion, etc. Two sample videos
are used here with resolution of 352 X 240 pixels using color
histogram approach in the uncompressed media. An attempt is made
for the retrieval of color video. The simulation is performed for the
abrupt change in video which yields 90% recall and precision value.
Abstract: Semilinear elliptic equations are ubiquitous in natural sciences. They give rise to a variety of important phenomena in quantum mechanics, nonlinear optics, astrophysics, etc because they have rich multiple solutions. But the nontrivial solutions of semilinear equations are hard to be solved for the lack of stabilities, such as Lane-Emden equation, Henon equation and Chandrasekhar equation. In this paper, bifurcation method is applied to solving semilinear elliptic equations which are with homogeneous Dirichlet boundary conditions in 2D. Using this method, nontrivial numerical solutions will be computed and visualized in many different domains (such as square, disk, annulus, dumbbell, etc).
Abstract: Preliminary results for a new flat plate test
facility are presented here in the form of Computational Fluid Dynamics (CFD), flow visualisation, pressure measurements and thermal anemometry. The results from the CFD and flow
visualisation show the effectiveness of the plate design, with the trailing edge flap anchoring the stagnation point on the working surface and reducing the extent of the leading edge separation. The flow visualization technique demonstrates the
two-dimensionality of the flow in the location where the
thermal anemometry measurements are obtained.
Measurements of the boundary layer mean velocity profiles compare favourably with the Blasius solution, thereby allowing for comparison of future measurements with the
wealth of data available on zero pressure gradient Blasius
flows. Results for the skin friction, boundary layer thickness,
frictional velocity and wall shear stress are shown to agree well with the Blasius theory, with a maximum experimental deviation from theory of 5%. Two turbulence generating grids
have been designed and characterized and it is shown that the turbulence decay downstream of both grids agrees with established correlations. It is also demonstrated that there is
little dependence of turbulence on the freestream velocity.
Abstract: The study of the stress distribution on a hollow
cylindrical fiber placed in a composite material is considered in this
work and an analytical solution for this stress distribution has been
constructed. Finally some parameters such as fiber-s thickness and
fiber-s length are considered and their effects on the distribution of
stress have been investigated. For finding the governing relations,
continuity equations for the axisymmetric problem in cylindrical
coordinate (r,o,z) are considered. Then by assuming some conditions
and solving the governing equations and applying the boundary
conditions, an equation relates the stress applied to the representative
volume element with the stress distribution on the fiber has been
found.
Abstract: The use of the mechanical simulation (in particular the finite element analysis) requires the management of assumptions in order to analyse a real complex system. In finite element analysis (FEA), two modeling steps require assumptions to be able to carry out the computations and to obtain some results: the building of the physical model and the building of the simulation model. The simplification assumptions made on the analysed system in these two steps can generate two kinds of errors: the physical modeling errors (mathematical model, domain simplifications, materials properties, boundary conditions and loads) and the mesh discretization errors. This paper proposes a mesh adaptive method based on the use of an h-adaptive scheme in combination with an error estimator in order to choose the mesh of the simulation model. This method allows us to choose the mesh of the simulation model in order to control the cost and the quality of the finite element analysis.
Abstract: This paper present an efficient and reliable technique of optimization which combined fuel cost economic optimization and emission dispatch using the Sigmoid Decreasing Inertia Weight Particle Swarm Optimization algorithm (PSO) to reduce the cost of fuel and pollutants resulting from fuel combustion by keeping the output of generators, bus voltages, shunt capacitors and transformer tap settings within the security boundary. The performance of the proposed algorithm has been demonstrated on IEEE 30-bus system with six generating units. The results clearly show that the proposed algorithm gives better and faster speed convergence then linearly decreasing inertia weight.
Abstract: A new analytical model is developed which provides
close-formed solutions for both transient indoor and envelope
temperature changes in buildings. Time-dependent boundary
temperature is presented as Fourier series which can approximate real
weather conditions. The final close-formed solutions are simple,
concise, and comprehensive. The model was compared with
numerical results and good accuracy was obtained. The model can
be used as design and control guidelines in engineering applications
for analysing mechanical heat transfer properties for buildings.
Abstract: In the recent years, functionally gradient materials (FGMs) have gained considerable attention in the high temperature environment applications. In this paper, free vibration of thin functionally graded cylindrical shell with hole composed of stainless steel and zirconia is studied. The mechanical properties vary smoothly and continuously from one surface to the other according to a volume fraction power-law distribution. The Influence of shell geometrical parameters, variations of volume fractions and boundary conditions on natural frequency is considered. The equations of motion are based on strains-displacement relations from Love-s shell theory and Rayleigh method. The results have been obtained for natural frequencies of cylindrical shell with holes for different shape, number and location in this paper.
Abstract: In this paper the Differential Quadrature Method (DQM) is employed to study the coupled lateral-torsional free vibration behavior of the laminated composite beams. In such structures due to the fiber orientations in various layers, the lateral displacement leads to a twisting moment. The coupling of lateral and torsional vibrations is modeled by the bending-twisting material coupling rigidity. In the present study, in addition to the material coupling, the effects of shear deformation and rotary inertia are taken into account in the definition of the potential and kinetic energies of the beam. The governing differential equations of motion which form a system of three coupled PDEs are solved numerically using DQ procedure under different boundary conditions consist of the combinations of simply, clamped, free and other end conditions. The resulting natural frequencies and mode shapes for cantilever beam are compared with similar results in the literature and good agreement is achieved.
Abstract: The recent growth of using multimedia transmission
over wireless communication systems, have challenges to protect the
data from lost due to wireless channel effect. Images are corrupted
due to the noise and fading when transmitted over wireless channel,
in wireless channel the image is transmitted block by block, Due to
severe fading, entire image blocks can be damaged. The aim of this
paper comes out from need to enhance the digital images at the
wireless receiver side. Proposed Boundary Interpolation (BI)
Algorithm using wavelet, have been adapted here used to
reconstruction the lost block in the image at the receiver depend on
the correlation between the lost block and its neighbors. New
Proposed technique by using Boundary Interpolation (BI) Algorithm
using wavelet with Pixel interleaver has been implemented. Pixel
interleaver work on distribute the pixel to new pixel position of
original image before transmitting the image. The block lost through
wireless channel is only effects individual pixel. The lost pixels at the
receiver side can be recovered by using Boundary Interpolation (BI)
Algorithm using wavelet. The results showed that the New proposed
algorithm boundary interpolation (BI) using wavelet with pixel
interleaver is better in term of MSE and PSNR.