Abstract: This paper presents an effective traffic lights detection
method at the night-time. First, candidate blobs of traffic lights are
extracted from RGB color image. Input image is represented on the
dominant color domain by using color transform proposed by Ruta,
then red and green color dominant regions are selected as candidates.
After candidate blob selection, we carry out shape filter for noise
reduction using information of blobs such as length, area, area of
boundary box, etc. A multi-class classifier based on SVM (Support
Vector Machine) applies into the candidates. Three kinds of features
are used. We use basic features such as blob width, height, center
coordinate, area, area of blob. Bright based stochastic features are also
used. In particular, geometric based moment-s values between
candidate region and adjacent region are proposed and used to improve
the detection performance. The proposed system is implemented on
Intel Core CPU with 2.80 GHz and 4 GB RAM and tested with the
urban and rural road videos. Through the test, we show that the
proposed method using PF, BMF, and GMF reaches up to 93 % of
detection rate with computation time of in average 15 ms/frame.
Abstract: Recently, Northeast Asia has become one of the three
largest trade areas, covering approximately 30% of the total trade
volume of the world. However, the distribution facilities are saturated
due to the increase in the transportation volume within the area and
with the European countries. In order to accommodate the increase of
the transportation volume, the transportation networking with the
major countries in Northeast Asia and Europe is absolutely necessary.
The Eurasian Logistics Network will develop into an international
passenger transportation network covering the Northeast Asian region
and an international freight transportation network connecting across
Eurasia Continent. This paper surveys the changes and trend of the
distribution network in the Eurasian Region according to the political,
economic and environmental changes of the region, analyses the
distribution network according to the changes in the transportation
policies of the related countries, and provides the direction of the
development of composite transportation on the basis of the present
conditions of transportation means. The transportation means optimal
for the efficiency of transportation system are suggested to be train
ferries, sea & rail or sea & rail & sea. It is suggested to develop
diversified composite transportation means and routes within the
boundary of international cooperation system.
Abstract: Stress-strain curve of inter-tube connected carbon nanotube (CNT) reinforced polymer composite under axial loading generated from molecular dynamics simulation is presented. Comparison of the response to axial mechanical loading between this composite system with composite systems reinforced by long, continuous CNTs (replicated via periodic boundary conditions) and short, discontinuous CNTs has been made. Simulation results showed that the inter-tube connection improved the mechanical properties of short discontinuous CNTs dramatically. Though still weaker than long CNT/polymer composite, more remarkable increase in the stiffness relative to the polymer was observed in the inter-tube connected CNT/polymer composite than in the discontinuous CNT/polymer composite. The manually introduced bridge break process resulted in a stress-strain curve of ductile fracture mode, which is consistent with the experimental result.
Abstract: Generally flow behavior in centrifugal fan is observed
to be in a state of instability with flow separation zones on suction
surface as well as near the front shroud. Overall performance of the
diffusion process in a centrifugal fan could be enhanced by
judiciously introducing the boundary layer suction slots. With easy
accessibility of CFD as an analytical tool, an extensive numerical
whole field analysis of the effect of boundary layer suction slots in
discrete regions of suspected separation points is possible. This paper
attempts to explore the effect of boundary layer suction slots
corresponding to various geometrical locations on the impeller with
converging configurations for the slots. The analysis shows that the
converging suction slots located on the impeller blade about 25%
from the trailing edge, significantly improves the static pressure
recovery across the fan. Also it is found that Slots provided at a
radial distance of about 12% from the leading and trailing edges
marginally improve the static pressure recovery across the fan.
Abstract: A kind of singularly perturbed boundary value problems is under consideration. In order to obtain its approximation, simple upwind difference discretization is applied. We use a moving mesh iterative algorithm based on equi-distributing of the arc-length function of the current computed piecewise linear solution. First, a maximum norm a posteriori error estimate on an arbitrary mesh is derived using a different method from the one carried out by Chen [Advances in Computational Mathematics, 24(1-4) (2006), 197-212.]. Then, basing on the properties of discrete Green-s function and the presented posteriori error estimate, we theoretically prove that the discrete solutions computed by the algorithm are first-order uniformly convergent with respect to the perturbation parameter ε.
Abstract: This research attempts to explore gaps in Information
Systems (IS) and innovation literatures by developing a model of
Information Technology (IT) capability in enabling innovation. The
research was conducted by using semi-structured interview with six
innovators in business consulting, financial, healthcare and academic
organizations. The interview results suggest four elements of ITenabled
innovation capability which are information (ability to
capture ideas and knowledge), connectivity (ability to bridge
geographical boundary and mobilize human resources),
communication (ability to attain and engage relationships between
human resources) and transformation (ability to change the functions
and process integrations) in defining IT-enabled innovation platform.
The results also suggests innovators- roles and IT capability.
Abstract: Dynamics of a vapour bubble generated due to a high local energy input near a circular thin bronze plate in the absence of the buoyancy forces is numerically investigated in this paper. The bubble is generated near a thin bronze plate and during the growth and collapse of the bubble, it deforms the nearby plate. The Boundary Integral Equation Method is employed for numerical simulation of the problem. The fluid is assumed to be incompressible, irrotational and inviscid and the surface tension on the bubble boundary is neglected. Therefore the fluid flow around the vapour bubble can be assumed as a potential flow. Furthermore, the thin bronze plate is assumed to have perfectly plastic behaviour. Results show that the displacement of the circular thin bronze plate has considerable effect on the dynamics of its nearby vapour bubble. It is found that by decreasing the thickness of the thin bronze plate, the growth and collapse rate of the bubble becomes higher and consequently the lifetime of the bubble becomes shorter.
Abstract: Droplet size distributions in the cold spray of a fuel
are important in observed combustion behavior. Specification of
droplet size and velocity distributions in the immediate downstream
of injectors is also essential as boundary conditions for advanced
computational fluid dynamics (CFD) and two-phase spray transport
calculations. This paper describes the development of a new model to
be incorporated into maximum entropy principle (MEP) formalism
for prediction of droplet size distribution in droplet formation region.
The MEP approach can predict the most likely droplet size and
velocity distributions under a set of constraints expressing the
available information related to the distribution.
In this article, by considering the mechanisms of turbulence
generation inside the nozzle and wave growth on jet surface, it is
attempted to provide a logical framework coupling the flow inside the
nozzle to the resulting atomization process. The purpose of this paper
is to describe the formulation of this new model and to incorporate it
into the maximum entropy principle (MEP) by coupling sub-models
together using source terms of momentum and energy. Comparison
between the model prediction and experimental data for a gas turbine
swirling nozzle and an annular spray indicate good agreement
between model and experiment.
Abstract: The present microfluidic study is emphasizing the flow behavior within a Y shape micro-bifurcation in two similar flow configurations. We report here a numerical and experimental investigation on the velocity profiles evolution and secondary flows, manifested at different Reynolds numbers (Re) and for two different boundary conditions. The experiments are performed using special designed setup based on optical microscopic devices. With this setup, direct visualizations and quantitative measurements of the path-lines are obtained. A Micro-PIV measurement system is used to obtain velocity profiles distributions in a spatial evolution in the main flows domains. The experimental data is compared with numerical simulations performed with commercial computational code FLUENT in a 3D geometry with the same dimensions as the experimental one. The numerical flow patterns are found to be in good agreement with the experimental manifestations.
Abstract: In this work, are discussed two formulations of the boundary element method - BEM to perform linear bending analysis of plates reinforced by beams. Both formulations are based on the Kirchhoff's hypothesis and they are obtained from the reciprocity theorem applied to zoned plates, where each sub-region defines a beam or a slab. In the first model the problem values are defined along the interfaces and the external boundary. Then, in order to reduce the number of degrees of freedom kinematics hypothesis are assumed along the beam cross section, leading to a second formulation where the collocation points are defined along the beam skeleton, instead of being placed on interfaces. On these formulations no approximation of the generalized forces along the interface is required. Moreover, compatibility and equilibrium conditions along the interface are automatically imposed by the integral equation. Thus, these formulations require less approximation and the total number of the degree s of freedom is reduced. In the numerical examples are discussed the differences between these two BEM formulations, comparing as well the results to a well-known finite element code.
Abstract: Three dimensional simulations are carried out to estimate the effect of wind direction, wind speed and geometry on the flow and dispersion of vehicular pollutant in a street canyon. The pollutant sources are motor vehicles passing between the two buildings. Suitable emission factors for petrol and diesel vehicles at varying vehicle speed are used for the estimation of the rate of emission from the streets. The dispersion of automobile pollutant released from the street is simulated by introducing vehicular emission source term as a fixed-flux boundary condition at the ground level over the road. The emission source term is suitably calculated by adopting emission factors from literature for varying conditions of street traffic. It is observed that increase in wind angle disturbs the symmetric pattern of pollution distribution along the street length. The concentration increases in the far end of the street as compared to the near end.
Abstract: The aerodynamic noise radiation from a side view mirror (SVM) in the high-speed airflow is calculated by the combination of unsteady incompressible fluid flow analysis and acoustic analysis. The transient flow past the generic SVM is simulated with variable turbulence model, namely DES Detached Eddy Simulation and LES (Large Eddy Simulation). Detailed velocity vectors and contour plots of the time-varying velocity and pressure fields are presented along cut planes in the flow-field. Mean and transient pressure are also monitored at several points in the flow field and compared to corresponding experimentally data published in literature. The acoustic predictions made using the Ffowcs-Williams-Hawkins acoustic analogy (FW-H) and the boundary element (BEM).
Abstract: Elastic boundary eigensolution problems are converted
into boundary integral equations by potential theory. The kernels of
the boundary integral equations have both the logarithmic and Hilbert
singularity simultaneously. We present the mechanical quadrature
methods for solving eigensolutions of the boundary integral equations
by dealing with two kinds of singularities at the same time. The methods
possess high accuracy O(h3) and low computing complexity. The
convergence and stability are proved based on Anselone-s collective
compact theory. Bases on the asymptotic error expansion with odd
powers, we can greatly improve the accuracy of the approximation,
and also derive a posteriori error estimate which can be used for
constructing self-adaptive algorithms. The efficiency of the algorithms
are illustrated by numerical examples.
Abstract: This paper analyses the unsteady, two-dimensional
stagnation point flow of an incompressible viscous fluid over a flat
sheet when the flow is started impulsively from rest and at the same
time, the sheet is suddenly stretched in its own plane with a velocity
proportional to the distance from the stagnation point. The partial
differential equations governing the laminar boundary layer forced
convection flow are non-dimensionalised using semi-similar
transformations and then solved numerically using an implicit finitedifference
scheme known as the Keller-box method. Results
pertaining to the flow and heat transfer characteristics are computed
for all dimensionless time, uniformly valid in the whole spatial region
without any numerical difficulties. Analytical solutions are also
obtained for both small and large times, respectively representing the
initial unsteady and final steady state flow and heat transfer.
Numerical results indicate that the velocity ratio parameter is found
to have a significant effect on skin friction and heat transfer rate at
the surface. Furthermore, it is exposed that there is a smooth
transition from the initial unsteady state flow (small time solution) to
the final steady state (large time solution).
Abstract: In manufacturing industries, development of measurement leads to increase the number of monitoring variables and eventually the importance of multivariate control comes to the fore. Statistical process control (SPC) is one of the most widely used as multivariate control chart. Nevertheless, SPC is restricted to apply in processes because its assumption of data as following specific distribution. Unfortunately, process data are composed by the mixture of several processes and it is hard to estimate as one certain distribution. To alternative conventional SPC, therefore, nonparametric control chart come into the picture because of the strength of nonparametric control chart, the absence of parameter estimation. SVDD based control chart is one of the nonparametric control charts having the advantage of flexible control boundary. However,basic concept of SVDD has been an oversight to the important of data characteristic, density distribution. Therefore, we proposed DW-SVDD (Density Weighted SVDD) to cover up the weakness of conventional SVDD. DW-SVDD makes a new attempt to consider dense of data as introducing the notion of density Weight. We extend as control chart using new proposed SVDD and a simulation study of various distributional data is conducted to demonstrate the improvement of performance.
Abstract: The demand on High voltage (HV) infrastructures is growing due to the corresponding growth in industries and population. New or upgraded HV infrastructure has safety implications since Transmission mains usually occupy the same easement in the vicinity of neighbouring residents. Transmission mains consist of underground (UG) and overhead (OH) sections and the transition between the UG and OH section is known as the UGOH pole. The existence of two transmission mains in the same easement can dictate to resort to more complicated earthing design in order to mitigate the effect of AC interference, and in some cases it can also necessitates completing a Split Study of the system. This paper provides an overview of the AC interference, Split Study and the earthing of an underground feeder including the UGOH pole .In addition, this paper discusses the use of different link boxes on the UG feeder and presents a case study that represent a clear example of the Ac interference and Split factor. Finally, a few recommendations are provided to achieve a safety zone in the area beyond the boundary of the HV system.
Abstract: In this paper a study on the vibration of thin
cylindrical shells with ring supports and made of functionally graded
materials (FGMs) composed of stainless steel and nickel is presented.
Material properties vary along the thickness direction of the shell
according to volume fraction power law. The cylindrical shells have
ring supports which are arbitrarily placed along the shell and impose
zero lateral deflections. The study is carried out based on third order
shear deformation shell theory (T.S.D.T). The analysis is carried out
using Hamilton-s principle. The governing equations of motion of
FGM cylindrical shells are derived based on shear deformation
theory. Results are presented on the frequency characteristics,
influence of ring support position and the influence of boundary
conditions. The present analysis is validated by comparing results
with those available in the literature.
Abstract: Meshing is the process of discretizing problem
domain into many sub domains before the numerical calculation can
be performed. One of the most popular meshes among many types of meshes is tetrahedral mesh, due to their flexibility to fit into almost
any domain shape. In both 2D and 3D domains, triangular and tetrahedral meshes can be generated by using Delaunay triangulation.
The quality of mesh is an important factor in performing any Computational Fluid Dynamics (CFD) simulations as the results is
highly affected by the mesh quality. Many efforts had been done in
order to improve the quality of the mesh. The paper describes a mesh
generation routine which has been developed capable of generating
high quality tetrahedral cells in arbitrary complex geometry. A few
test cases in CFD problems are used for testing the mesh generator.
The result of the mesh is compared with the one generated by a
commercial software. The results show that no sliver exists for the
meshes generated, and the overall quality is acceptable since the percentage of the bad tetrahedral is relatively small. The boundary
recovery was also successfully done where all the missing faces are
rebuilt.
Abstract: A multiple-option analytical model for the evaluation of the energy performance and distribution of aerodynamic forces acting on a vertical-axis Darrieus wind turbine depending on both rotor architecture and operating conditions is presented. For this purpose, a numerical algorithm, capable of generating the desired rotor conformation depending on design geometric parameters, is coupled to a Single/Double-Disk Multiple-Streamtube Blade Element – Momentum code. Both single and double-disk configurations are analyzed and model predictions are compared to literature experimental data in order to test the capability of the code for predicting rotor performance. Effective airfoil characteristics based on local blade Reynolds number are obtained through interpolation of literature low-Reynolds airfoil databases. Some corrections are introduced inside the original model with the aim of simulating also the effects of blade dynamic stall, rotor streamtube expansion and blade finite aspect ratio, for which a new empirical relationship to better fit the experimental data is proposed. In order to predict also open field rotor operation, a freestream wind shear profile is implemented, reproducing the effect of atmospheric boundary layer.
Abstract: Arbitrarily shaped video objects are an important
concept in modern video coding methods. The techniques presently
used are not based on image elements but rather video objects having
an arbitrary shape. In this paper, spatial shape error concealment
techniques to be used for object-based image in error-prone
environments are proposed. We consider a geometric shape
representation consisting of the object boundary, which can be
extracted from the α-plane. Three different approaches are used to
replace a missing boundary segment: Bézier interpolation, Bézier
approximation and NURBS approximation. Experimental results on
object shape with different concealment difficulty demonstrate the
performance of the proposed methods. Comparisons with proposed
methods are also presented.