Abstract: Because road traffic accidents are a major source of death worldwide, attempts have been made to create Advanced Driver Assistance Systems (ADAS) able to detect vehicle, driver and
environmental conditions that are cues for possible potential accidents. This paper presents continued work on a novel Nonintrusive
Intelligent Driver Assistance and Safety System (Ni-DASS)
for assessing driver attention and hazard awareness. It uses two onboard
CCD cameras – one observing the road and the other observing
the driver-s face. The windscreen is divided into cells and analysis of
the driver-s eye-gaze patterns allows Ni-DASS to determine the windscreen cell the driver is focusing on using eye-gesture templates.
Intersecting the driver-s field of view through the observed
windscreen cell with subsections of the camera-s field of view containing a potential hazard allows Ni-DASS to estimate the
probability that the driver has actually observed the hazard. Results
have shown that the proposed technique is an accurate enough
measure of driver observation to be useful in ADAS systems.
Abstract: The persistent nature of perfluorochemicals (PFCs) has attracted global concern in recent years. Perfluorooctanesulfonate (PFOS) and perfluorooctanoate (PFOA) are the most commonly found PFC compounds, and thus their fate and transport play key roles in PFC distribution in the natural environment. The kinetic behavior of PFOS or PFOA on boehmite consists of a fast adsorption process followed by a slow adsorption process which may be attributed to the slow transport of PFOS or PFOA into the boehmite pore surface. The adsorption isotherms estimated the maximum adsorption capacities of PFOS and PFOA on boehmite as 0.877 μg/m2 and 0.633 μg/m2, with the difference primarily due to their different functional groups. The increase of solution pH led to a moderate decrease of PFOS and PFOA adsorption, owing to the increase of ligand exchange reactions and the decrease of electrostatic interactions. The presence of NaCl in solution demonstrated negative effects for PFOS and PFOA adsorption on boehmite surfaces, with potential mechanisms being electrical double layer compression, competitive adsorption of chloride.
Abstract: The purpose of this work was to inspect the potential
of vincristine-dextran complex loaded solid lipid nanoparticles for
drug delivery to the brain.
The nanoparticles were stained with a fluorescence dye and their
plasma pharmacokinetic and brain concentrations were investigated
following injection to rats.
The result revealed a significant improvement in the plasma
concentration profile of the SLN injected animals as well as a sharp
increased concentration in the brains.
Abstract: Liners are made to protect the groundwater table from
the infiltration of leachate which normally carries different kinds of
toxic materials from landfills. Although these liners are engineered to
last for long period of time; unfortunately these liners fail; therefore,
toxic materials pass to groundwater. This paper focuses on the
changes of the hydraulic conductivity of a sand-bentonite liner due to
the infiltration of biofuel and ethanol fuel. Series of laboratory tests
were conducted in 20-cm-high PVC columns. Several compositions
of sand-bentonite liners were tested: 95% sand: 5% bentonite; 90%
sand: 10% bentonite; and 100% sand (passed mesh #40). The
columns were subjected to extreme pressures of 40 kPa, and 100 kPa
to evaluate the transport of alternative fuels (biofuel and ethanol
fuel). For comparative studies, similar tests were carried out using
water. Results showed that hydraulic conductivity increased due to
the infiltration of alternative fuels through the liners. Accordingly,
the increase in the hydraulic conductivity showed significant
dependency on the type of liner mixture and the characteristics of the
liquid. The hydraulic conductivity of a liner (subjected to biofuel
infiltration) consisting of 5% bentonite: 95% sand under pressure of
40 kPa and 100 kPa had increased by one fold. In addition, the
hydraulic conductivity of a liner consisting of 10% bentonite: 90%
sand under pressure of 40 kPa and 100 kPa and infiltrated by biofuel
had increased by three folds. On the other hand, the results obtained
by water infiltration under 40 kPa showed lower hydraulic
conductivities of 1.50×10-5 and 1.37×10-9 cm/s for 5% bentonite:
95% sand, and 10% bentonite: 90% sand, respectively. Similarly,
under 100 kPa, the hydraulic conductivities were 2.30×10-5 and
1.90×10-9 cm/s for 5% bentonite: 95% sand, and 10% bentonite: 90%
sand, respectively.
Abstract: In the present work the internal sulfate attack on
pastes made from pure clinker phases was studied. Two binders were
produced: (a) a binder with 2% C3A and 18% C4AF content; (b) a
binder with 10% C3A and C4AF content each. Gypsum was used as
the sulfate bearing compound, while calcium carbonate added to
differentiate the binders produced. The phases formed were identified
by XRD analysis. The results showed that ettringite was the
deterioration phase detected in the case of the low C3A content
binder. Carbonation occurred in the specimen without calcium
carbonate addition, while portlandite was observed in the one
containing calcium carbonate. In the case of the high C3A content
binder, traces of thaumasite were detected when calcium carbonate
was not incorporated in the binder. A solid solution of thaumasite and
ettringite was found when calcium carbonate was added. The amount
of C3A had not fully reacted with sulfates, since its corresponding
peaks were detected.
Abstract: ZnO nanostructure were synthesized via microwave
method using zinc acetate as starting material, guanidinium as
structure directing agents, and water as solvent.. This work
investigates the photodegradation of azo dyes using the ZnO Flowerlike
in aqueous solutions. As synthesized ZnO samples were
characterized using X-Ray powder diffraction (XRD), scanning
electron microscopy (SEM), and FTIR spectroscopy.In this work
photodecolorization of congored azo dye under UV irradiation by
nano ZnO was studied.
Abstract: In wireless and mobile communications, this progress
provides opportunities for introducing new standards and improving
existing services. Supporting multimedia traffic with wireless networks
quality of service (QoS). In this paper, a grey-fuzzy controller for radio
resource management (GF-RRM) is presented to maximize the number
of the served calls and QoS provision in wireless networks. In a
wireless network, the call arrival rate, the call duration and the
communication overhead between the base stations and the control
center are vague and uncertain. In this paper, we develop a method to
predict the cell load and to solve the RRM problem based on the
GF-RRM, and support the present facility has been built on the
application-level of the wireless networks. The GF-RRM exhibits the
better adaptability, fault-tolerant capability and performance than other
algorithms. Through simulations, we evaluate the blocking rate, update
overhead, and channel acquisition delay time of the proposed method.
The results demonstrate our algorithm has the lower blocking rate, less
updated overhead, and shorter channel acquisition delay.
Abstract: The fluid flow and the properties of the hydraulic
fluid inside a torque converter are the main topics of interest in this
research. The primary goal is to investigate the applicability of
various viscous fluids inside the torque converter. The Taguchi
optimization method is adopted to analyse the fluid flow in a torque
converter from a design perspective. Calculations are conducted in
maximizing the pressure since greater the pressure, greater the torque
developed. Using the values of the S/N ratios obtained, graphs are
plotted. Computational Fluid Dynamics (CFD) analysis is also
conducted.
Abstract: Mobile learning (M-learning) integrates mobile
devices and wireless computing technology to enhance the current
conventional learning system. However, there are constraints which
are affecting the implementation of platform and device independent
M-learning. The main aim of this research is to fulfill the following
main objectives: to develop platform independent mobile learning
tool (M-LT) for structured programming course, and evaluate its
effectiveness and usability using ADDIE instructional design model
(ISD) as M-LT life cycle. J2ME (Java 2 micro edition) and XML
(Extensible Markup Language) were used to develop platform
independent M-LT. It has two modules lecture materials and quizzes.
This study used Quasi experimental design to measure effectiveness
of the tool. Meanwhile, questionnaire is used to evaluate the usability
of the tool. Finally, the results show that the system was effective and
also usability evaluation was positive.
Abstract: This paper presents the design and layout of a two stage, high speed operational amplifiers using standard 0.35um CMOS technology. The design procedure involves designing the bias circuit, the differential input pair, and the gain stage using CAD tools. Both schematic and layout of the operational amplifier along with the comparison in the results of the two has been presented. The operational amplifier designed, has a gain of 93.51db at low frequencies. It has a gain bandwidth product of 55.07MHz, phase margin of 51.9º and a slew rate of 22v/us for a load of capacitor of 10pF.
Abstract: Severe heart failure is a common problem that has a significant effect on health expenditures in industrialized countries; moreover it reduces patient-s quality of life. However, current research usually focuses either on detailed modeling of the heart or on detailed modeling of the cardiovascular system. Thus, this paper aims to present a sophisticated model of the heart enhanced with an extensive model of the cardiovascular system. Special interest is on the pressure and flow values close to the heart since these values are critical to accurately diagnose causes of heart failure. The model is implemented in Dymola an object-oriented, physical modeling language. Results achieved with the novel model show overall feasibility of the approach. Moreover, results are illustrated and compared to other models. The novel model shows significant improvements.
Abstract: This study presents energy saving in general-purpose
pumps widely used in industrial applications. Such pumps are
normally driven by a constant-speed electrical motor which in most
applications must support varying load conditions. This is equivalent
to saying the loading conditions mismatch the designed optimal
energy consumption requirements of the intended application thus
resulting in substantial energy losses. In the held experiments it was
indicated that combination of mechanical and electrical speed drives
can contribute to lower energy consumption in the pump without
negatively distorting the required performance indices of a typical
centrifugal pump at substantially lower energy consumption. The
registered energy savings were recorded to be within the 15-40%
margin. It was also indicated that although VSDs are installed at a
cost, the financial burden is balanced against the earnings resulting
from the associated energy savings.
Abstract: There are multiple ways to implement a decimator
filter. This paper addresses usage of CIC (cascaded-integrator-comb)
filter and HB (half band) filter as the decimator filter to reduce the
frequency sample rate by factor of 64 and detail of the
implementation step to realize this design in hardware. Low power
design approach for CIC filter and half band filter will be discussed.
The filter design is implemented through MATLAB system
modeling, ASIC (application specific integrated circuit) design flow
and verified using a FPGA (field programmable gate array) board
and MATLAB analysis.
Abstract: Increasing user comfort and reducing operation costs
have always been primary objectives of lighting control strategies in a
building. This paper proposes an architecture of the lighting control
system for a daylit office. The system consists of the lighting
controller, A/D & D/A converter, dimmable LED lights, and the
lighting management software. Verification tests are conducted using
the proposed system specialized for the interior lighting of a open-plan
office. The results showed the proposed architecture of the lighting
system would improve the overall system reliability, lower the system
cost, and provide ease of installation and maintenance.
Abstract: Objective: The objective of this paper is to assess the
hospitals preparedness for emergency using WHO standards.
Method: This is a cross-sectional study, consisted of site visit,
questionnaire survey, 16 health facilities were included. The WHO
standard for emergency preparedness of health facilities was used to
evaluate and assess the hospitals preparedness of health facilities.
Result: 13 hospitals were responded. They scored below average
in all measure >75%), while above average score was in 7 out 9 nine
measure with a range of 8%-25%. Un acceptable below average was
noted in two measures only.
Discussion: The biggest challenge facing the hospitals in their
emergency intervention is the lack of pre-emergency and emergency
preparedness plans as well as the coordination of the hospitals
response mechanisms.
Conclusion: The studied hospitals presently are far from
international disasters preparedness protocols. That necessitates
improvements in emergency preparedness, as well as in physician
skills for injury management.
Abstract: Severe acute respiratory syndrome (SARS) is a respiratory disease in humans which is caused by the SARS coronavirus. The treatment of coronavirus-associated SARS has been evolving and so far there is no consensus on an optimal regimen. The mainstream therapeutic interventions for SARS involve broad-spectrum antibiotics and supportive care, as well as antiviral agents and immunomodulatory therapy. The Protein- Ligand interaction plays a significant role in structural based drug designing. In the present work we have taken the receptor Angiotensin converting enzyme 2 and identified the drugs that are commonly used against SARS. They are Lopinavir, Ritonavir, Ribavirin, and Oseltamivir. The receptor Angiotensin converting enzyme 2 (ACE-2) was docked with above said drugs and the energy value obtained are as follows, Lopinavir (-292.3), Ritonavir (-325.6), Oseltamivir (- 229.1), Ribavirin (-208.8). Depending on the least energy value we have chosen the best two drugs out of the four conventional drugs. We tried to improve the binding efficiency and steric compatibility of the two drugs namely Ritonavir and Lopinavir. Several modifications were made to the probable functional groups (phenylic, ketonic groups in case of Ritonavir and carboxylic groups in case of Lopinavir respectively) which were interacting with the receptor molecule. Analogs were prepared by Marvin Sketch software and were docked using HEX docking software. Lopinavir analog 8 and Ritonavir analog 11 were detected with significant energy values and are probable lead molecule. It infers that some of the modified drugs are better than the original drugs. Further work can be carried out to improve the steric compatibility of the drug based upon the work done above for a more energy efficient binding of the drugs to the receptor.
Abstract: A new reverse phase-high performance liquid chromatography (RP-HPLC) method with fluorescent detector (FLD) was developed and optimized for Norfloxacin determination in human plasma. Mobile phase specifications, extraction method and excitation and emission wavelengths were varied for optimization. HPLC system contained a reverse phase C18 (5 μm, 4.6 mm×150 mm) column with FLD operated at excitation 330 nm and emission 440 nm. The optimized mobile phase consisted of 14% acetonitrile in buffer solution. The aqueous phase was prepared by mixing 2g of citric acid, 2g sodium acetate and 1 ml of triethylamine in 1 L of Milli-Q water was run at a flow rate of 1.2 mL/min. The standard curve was linear for the range tested (0.156–20 μg/mL) and the coefficient of determination was 0.9978. Aceclofenac sodium was used as internal standard. A detection limit of 0.078 μg/mL was achieved. Run time was set at 10 minutes because retention time of norfloxacin was 0.99 min. which shows the rapidness of this method of analysis. The present assay showed good accuracy, precision and sensitivity for Norfloxacin determination in human plasma with a new internal standard and can be applied pharmacokinetic evaluation of Norfloxacin tablets after oral administration in human.
Abstract: The Time-Domain Boundary Element Method (TDBEM)
is a well known numerical technique that handles quite
properly dynamic analyses considering infinite dimension media.
However, when these analyses are also related to nonlinear behavior,
very complex numerical procedures arise considering the TD-BEM,
which may turn its application prohibitive. In order to avoid this
drawback and model nonlinear infinite media, the present work
couples two BEM formulations, aiming to achieve the best of two
worlds. In this context, the regions expected to behave nonlinearly
are discretized by the Domain Boundary Element Method (D-BEM),
which has a simpler mathematical formulation but is unable to deal
with infinite domain analyses; the TD-BEM is employed as in the
sense of an effective non-reflexive boundary. An iterative procedure
is considered for the coupling of the TD-BEM and D-BEM, which is
based on a relaxed renew of the variables at the common interfaces.
Elastoplastic models are focused and different time-steps are allowed
to be considered by each BEM formulation in the coupled analysis.
Abstract: This paper presents a sensor-based motion planning algorithm for 3-DOF car-like robots with a nonholonomic constraint. Similar to the classic Bug family algorithms, the proposed algorithm enables the car-like robot to navigate in a completely unknown environment using only the range sensor information. The car-like robot uses the local range sensor view to determine the local path so that it moves towards the goal. To guarantee that the robot can approach the goal, the two modes of motion are repeated, termed motion-to-goal and wall-following. The motion-to-goal behavior lets the robot directly move toward the goal, and the wall-following behavior makes the robot circumnavigate the obstacle boundary until it meets the leaving condition. For each behavior, the nonholonomic motion for the car-like robot is planned in terms of the instantaneous turning radius. The proposed algorithm is implemented to the real robot and the experimental results show the performance of proposed algorithm.
Abstract: This paper presents a cold flow simulation study of a small gas turbine combustor performed using laboratory scale test rig. The main objective of this investigation is to obtain physical insight of the main vortex, responsible for the efficient mixing of fuel and air. Such models are necessary for predictions and optimization of real gas turbine combustors. Air swirler can control the combustor performance by assisting in the fuel-air mixing process and by producing recirculation region which can act as flame holders and influences residence time. Thus, proper selection of a swirler is needed to enhance combustor performance and to reduce NOx emissions. Three different axial air swirlers were used based on their vane angles i.e., 30°, 45°, and 60°. Three-dimensional, viscous, turbulent, isothermal flow characteristics of the combustor model operating at room temperature were simulated via Reynolds- Averaged Navier-Stokes (RANS) code. The model geometry has been created using solid model, and the meshing has been done using GAMBIT preprocessing package. Finally, the solution and analysis were carried out in a FLUENT solver. This serves to demonstrate the capability of the code for design and analysis of real combustor. The effects of swirlers and mass flow rate were examined. Details of the complex flow structure such as vortices and recirculation zones were obtained by the simulation model. The computational model predicts a major recirculation zone in the central region immediately downstream of the fuel nozzle and a second recirculation zone in the upstream corner of the combustion chamber. It is also shown that swirler angles changes have significant effects on the combustor flowfield as well as pressure losses.