Abstract: The present work aims to throw light on the effects of
arcing in air on the surface state of contact pastilles made of silvernickel
Ag-Ni (60/40). Also, the photoelectric emission from these
electrical contacts has been investigated in the spectral range of 196-
256 nm. In order to study the effects of arcing on the EWF, the
metallic samples were subjected to electrical arcs in air, at
atmospheric pressure and room temperature, after that, they have
been introduced into the vacuum chamber of an experimental UHV
set-up for EWF measurements. Both Fowler method of isothermal
curves and linearized Fowler plots were used for the measurement of
the EWF by the photoelectric effect.
It has been found that the EWF varies with the number of applied
arcs. Thus, after 500 arcs in air, the observed EWF increasing is
probably due to progressive inclusion of oxide on alloy surface.
Microscopic examination is necessary to get better understandings on
EWF of silver alloys, for both virgin and arced electrical contacts.
Abstract: This study is used as a definition method to the value
and function in manufacturing sector. In concurrence of discussion
about present condition of modeling method, until now definition of
1D-CAE is ambiguity and not conceptual. Across all the physic fields,
those methods are defined with the formulation of differential
algebraic equation which only applied time derivation and simulation.
At the same time, we propose semi-acausal modeling concept and
differential algebraic equation method as a newly modeling method
which the efficiency has been verified through the comparison of
numerical analysis result between the semi-acausal modeling
calculation and FEM theory calculation.
Abstract: The study of organisations’ information security
cultures has attracted scholars as well as healthcare services industry
to research the topic and find appropriate tools and approaches to
develop a positive culture. The vast majority of studies in Saudi
national health services are on the use of technology to protect and
secure health services information. On the other hand, there is a lack
of research on the role and impact of an organisation’s cultural
dimensions on information security. This research investigated and
analysed the role and impact of cultural dimensions on information
security in Saudi Arabia health service. Hypotheses were tested and
two surveys were carried out in order to collect data and information
from three major hospitals in Saudi Arabia (SA). The first survey
identified the main cultural-dimension problems in SA health
services and developed an initial information security culture
framework model. The second survey evaluated and tested the
developed framework model to test its usefulness, reliability and
applicability. The model is based on human behaviour theory, where
the individual’s attitude is the key element of the individual’s
intention to behave as well as of his or her actual behaviour. The
research identified a set of cultural and sub-cultural dimensions in SA
health information security and services.
Abstract: Background: With the perceived pain and poor
function experienced following knee arthroplasty, patients usually
feel un-satisfied. Yet, a controversy still persists on the appropriate
operative technique that doesn’t affect proprioception much.
Purpose: This study compared the effects of Cruciate Retaining
(CR) and Posterior Stabilized (PS) total knee arthroplasty (TKA on
dynamic balance, pain and functional performance following
rehabilitation.
Methods: Thirty patients with CRTKA (group I), thirty with
PSTKA (group II) and fifteen indicated for arthroplasty but weren’t
operated on yet (group III) participated in the study. The mean age
was 54.53±3.44, 55.13±3.48 and 55.33±2.32 years and BMI
35.7±3.03, 35.7±1.99 and 35.73±1.03 kg/m2 for groups I, II and III
respectively. The Berg Balance Scale (BBS), WOMAC pain subscale
and Timed Up-and-Go (TUG) and Stair-Climbing (SC) tests were
used for assessment. Assessments were conducted four weeks preand
post-operatively, three, six and twelve months post-operatively
with the control group being assessed at the same time intervals. The
post-operative rehabilitation involved hospitalization (1st week),
home-based (2nd-4th weeks), and outpatient clinic (5th-12th weeks)
programs, follow-up to all groups for twelve months.
Results: The Mixed design MANOVA revealed that group I had
significantly lower pain scores and SC time compared with group II
three, six and twelve months post-operatively. Moreover, the BBS
scores increased significantly and the pain scores and TUG and SC
time decreased significantly six months post-operatively compared
with four weeks pre- and post-operatively and three months postoperatively
in groups I and II with the opposite being true four weeks
post-operatively. But no significant differences in BBS scores, pain
scores and TUG and SC time between six and twelve months postoperatively
in groups I and II.
Interpretation/Conclusion: CRTKA is preferable to PSTKA,
possibly due to the preserved human proprioceptors in the un-excised
PCL.
Abstract: A parametric study on circular thin-walled pipes
subjected to pure bending is performed. Both straight and curved
pipes are considered. Ratio D/t, initial pipe curvature and internal
pressure are the parameters varying in the analyses. The study is
mainly FEA-based.
It is found that negative curvatures (opposite to bending moment)
considerably increase stiffness and buckling limit of the pipe when no
internal pressure is acting and, similarly, positive curvatures decrease
the stiffness and buckling limit. For internal pressurised pipes the
effects of initial pipe curvature are less relevant. Results show that
this phenomenon is in relationship with the cross-section deformation
due to bending moment, which undergoes relevant ovalisation for no
pressurised pipes and little ovalisation for pressurised pipes.
Abstract: The main objective of this paper is study the influence
of carbon nano-tubes fibers and nano silica fibers on the
characteristic compressive strength and flexural strength on concrete
and cement mortar. Twelve tested specimens were tested with square
section its dimensions (4040 160) mm, divided into four groups.
The first and second group studied the effect of carbon nano-tubes
(CNTs) fibers with different percentage equal to 0.0, 0.11%, 0.22%,
and 0.33% by weight of cement and effect of nano-silica (nS) fibers
with different percentages equal to 0.0, 1.0%, 2.0%, and 3.0% by
weight of cement on the cement mortar. The third and fourth groups
studied the effect of CNTs fiber with different percentage equal to
0.0%, 0.11%, and 0.22% by weight of cement, and effect of nS fibers
with different percentages were equal to 0.0%, 1.0%, and 2.0% by
weight of cement on the concrete. The compressive strength and
flexural strength at 7, 28, and 90 days is determined. From analysis of
tested results concluded that the nano-fibers is more effective when
used with cement mortar more than used with concrete because of
increasing the surface area, decreasing the pore and the collection of
nano-fibers. And also by adding nano-fibers the improvement of
flexural strength of concrete and cement mortar is more than
improvement of compressive strength.
Abstract: In this study, composites were fabricated from oil
palm empty fruit bunch fiber and poly(lactic) acid by extrusion
followed by injection moulding. Surface of the fiber was pre-treated
by ultrasound in an alkali medium and treatment efficiency was
investigated by scanning electron microscopy (SEM) analysis and
Fourier transforms infrared spectrometer (FTIR). Effect of fiber
treatment on composite was characterized by tensile strength (TS),
tensile modulus (TM) and impact strength (IS). Furthermore,
biostrong impact modifier was incorporated into the treated fiber
composite to improve its impact properties. Mechanical testing
showed an improvement of up to 23.5% and 33.6% respectively for
TS and TM of treated fiber composite above untreated fiber
composite. On the other hand incorporation of impact modifier led to
enhancement of about 20% above the initial IS of the treated fiber
composite.
Abstract: The current study investigated the influence of milling
time and ball-to-powder (BPR) weight ratio on the microstructural
constituents and mechanical properties of bulk nanocrystalline Al;
Al-10%Cu; and Al-10%Cu-5%Ti alloys. Powder consolidation was
carried out using a high frequency induction heat sintering where the
processed metal powders were sintered into a dense and strong bulk
material. The powders and the bulk samples were characterized using
XRD and FEGSEM techniques. The mechanical properties were
evaluated at various temperatures of 25°C, 100°C, 200°C, 300°C and
400°C to study the thermal stability of the processed alloys. The
processed bulk nanocrystalline alloys displayed extremely high
hardness values even at elevated temperatures. The Al-10%Cu-5%Ti
alloy displayed the highest hardness values at room and elevated
temperatures which are related to the presence of Ti-containing
phases such as Al3Ti and AlCu2Ti. These phases are thermally stable
and retain the high hardness values at elevated temperatures up to
400ºC.
Abstract: In orthopedic surgery there are various situations in
which the surgeon needs to implement methods of cutting and
drilling the bone. With this type of procedure the generated friction
leads to a localized increase in temperature, which may lead to the
bone necrosis. Recognizing the importance of studying this
phenomenon, an experimental evaluation of the temperatures
developed during the procedure of drilling bone has been done.
Additionally the influence of the use of the procedure with / without
additional lubrication during drilling of bone has also been done. The
obtained results are presented and discussed and suggests an
advantage in using additional lubrication as a way to minimize the
appearance of bone tissue necrosis during bone drilling procedures.
Abstract: The present study was undertaken to investigate the
effect of pre-aging and aging parameters (time and temperature) on
the mechanical properties of Al-Mg-Zn (7075) alloys. Ultimate
tensile strength, 0.5% offset yield strength and % elongation
measurements were carried out on specimens prepared from cast and
heat treated 7075 alloys. Aging treatments were carried out for the as
solution treated (SHT) specimens (after quenching in warm water).
The specimens were aged at different conditions; Natural aging was
carried out at room temperature for different periods of time. Double
aging was performed for SHT conditions (pre-aged at different time
and temperature followed by high temperature aging). Ultimate
tensile strength, yield strength and % elongation as a function of
different pre-aging and aging parameters are analyzed to acquire an
understanding of the effects of these variables and their interactions
on the mechanical properties of Be-treated 7075 alloys.
Abstract: Universal modeling method well proven for industrial
compressors was applied for design of the high flow rate supersonic
stage. Results were checked by ANSYS CFX and NUMECA Fine
Turbo calculations. The impeller appeared to be very effective at
transonic flow velocities. Stator elements efficiency is acceptable at
design Mach numbers too. Their loss coefficient versus inlet flow
angle performances correlates well with Universal modeling
prediction. The impeller demonstrates ability of satisfactory operation
at design flow rate. Supersonic flow behavior in the impeller inducer
at the shroud blade to blade surface Φ des deserves additional study.
Abstract: There is an evident trend to elevate pressure ratio of a
single stage of a turbo compressors - axial compressors in particular.
Whilst there was an opinion recently that a pressure ratio 1,9 was a
reasonable limit, later appeared information on successful modeling
tested of stages with pressure ratio up to 2,8. The authors recon that
lack of information on high pressure stages makes actual a study of
rational choice of design parameters before high supersonic flow
problems solving. The computer program of an engineering type was
developed. Below is presented a sample of its application to study
possible parameters of the impeller of the stage with pressure ratio
3,0. Influence of two main design parameters on expected efficiency,
periphery blade speed and flow structure is demonstrated. The results
had lead to choose a variant for further analysis and improvement by
CFD methods.
Abstract: Many organizations bring e-Learning to use as a tool
in their training and human development department. It is getting
more popular because it is easy to access to get knowledge all the
time and also it provides a rich content, which can develop the
employees’ skill efficiently. This study is focused on the factors that
affect using e-Learning efficiently, so it will make job satisfaction
increasing. The questionnaires were sent to employees in large
commercial banks, which use e-Learning located in Bangkok, the
results from multiple linear regression analysis showed that
employee’s characteristics, characteristics of e-Learning, learning and
growth have influence on job satisfaction.
Abstract: Vancron 40, a nitrided powder metallurgical tool
Steel, is used in cold work applications where the predominant failure
mechanisms are adhesive wear or galling. Typical applications of
Vancron 40 are among others fine blanking, cold extrusion, deep
drawing and cold work rolls for cluster mills. Vancron 40 positive
results for cold work rolls for cluster mills and as a tool for some
severe metal forming process makes it competitive compared to other
type of work rolls that require higher precision, among others in cold
rolling of thin stainless steel, which required high surface finish
quality. In this project, three roll materials for cold rolling of stainless
steel strip was examined, Vancron 40, Narva 12B (a high-carbon,
high-chromium tool steel alloyed with tungsten) and Supra 3 (a
Chromium-molybdenum tungsten-vanadium alloyed high speed
steel). The purpose of this project was to study the depth profiles of
the ironed stainless steel strips, emergence of galling and to study the
lubrication performance used by steel industries. Laboratory
experiments were conducted to examine scratch of the strip, galling
and surface roughness of the roll materials under severe tribological
conditions. The critical sliding length for onset of galling was
estimated for stainless steel with four different lubricants. Laboratory
experiments result of performance evaluation of resistance capability
of rolls toward adhesive wear under severe conditions for low and
high reductions. Vancron 40 in combination with cold rolling
lubricant gave good surface quality, prevents galling of
metal surfaces and good bearing capacity.
Abstract: Physics Education Research (PER) results have shown
that students do not achieve the expected level of competency in
understanding the concepts of different domains of Physics learning
when taught by the traditional teaching methods, the concepts of
Electricity and Magnetism (E&M) being one among them.
Simulation being one of the valuable instructional tools renders an
opportunity to visualize varied experiences with such concepts.
Considering the electric force concept which requires extensive use
of vector representations, we report here the outcome of the research
results pertaining to the student understanding of this concept and the
role of simulation in using vector representation. The simulation
platform provides a positive impact on the use of vector
representation.
The first stage of this study involves eliciting and analyzing
student responses to questions that probe their understanding of the
concept of electrostatic force and this is followed by four stages of
student interviews as they use the interactive simulations of electric
force in one dimension. Student responses to the questions are
recorded in real time using electronic pad. A validation test interview
is conducted to evaluate students' understanding of the electric force
concept after using interactive simulation. Results indicate lack of
procedural knowledge of the vector representation. The study
emphasizes the need for the choice of appropriate simulation and
mode of induction for learning.
Abstract: Building loss estimation methodologies which have
been advanced considerably in recent decades are usually used to
estimate socio and economic impacts resulting from seismic structural
damage. In accordance with these methods, this paper presents the
evaluation of an annual loss probability of a reinforced concrete
moment resisting frame designed according to Korean Building Code.
The annual loss probability is defined by (1) a fragility curve obtained
from a capacity spectrum method which is similar to a method adopted
from HAZUS, and (2) a seismic hazard curve derived from annual
frequencies of exceedance per peak ground acceleration. Seismic
fragilities are computed to calculate the annual loss probability of a
certain structure using functions depending on structural capacity,
seismic demand, structural response and the probability of exceeding
damage state thresholds. This study carried out a nonlinear static
analysis to obtain the capacity of a RC moment resisting frame
selected as a prototype building. The analysis results show that the
probability of being extensive structural damage in the prototype
building is expected to 0.01% in a year.
Abstract: The number of Ground Motion Prediction Equations
(GMPEs) used for predicting peak ground acceleration (PGA) and
the number of earthquake recordings that have been used for fitting
these equations has increased in the past decades. The current PF-L
database contains 3550 recordings. Since the GMPEs frequently
model the peak ground acceleration the goal of the present study was
to refit a selection of 44 of the existing equation models for PGA in
light of the latest data. The algorithm Levenberg-Marquardt was used
for fitting the coefficients of the equations and the results are
evaluated both quantitatively by presenting the root mean squared
error (RMSE) and qualitatively by drawing graphs of the five best
fitted equations. The RMSE was found to be as low as 0.08 for the
best equation models. The newly estimated coefficients vary from the
values published in the original works.
Abstract: The prepreg process among the CFRP (Carbon Fiber
Reinforced Plastic) forming methods is the short term of
‘Pre-impregnation’, which is widely used for aerospace composites
that require a high quality property such as a fiber-reinforced woven
fabric, in which an epoxy hardening resin is impregnated the reality.
However, that this process requires continuous researches and
developments for its commercialization because the delamination
characteristically develops between the layers when a great weight is
loaded from outside to supplement such demerit, three lamination
methods among the prepreg lamination methods of CFRP were
designed to minimize the delamination between the layers due to
external impacts. Further, the newly designed methods and the
existing lamination methods were analyzed through a mechanical
characteristic test, Interlaminar Shear Strength test. The Interlaminar
Shear Strength test result confirmed that the newly proposed three
lamination methods, i.e. the Roll, Half and Zigzag laminations,
presented more excellent strengths compared to the conventional Ply
lamination. The interlaminar shear strength in the roll method with
relatively dense fiber distribution was approximately 1.75% higher
than that in the existing ply lamination method, and in the half method,
it was approximately 0.78% higher.
Abstract: In this paper, the electromagnetic shielding
characteristics of an up-to-date typical carbon filler material, carbon
fiber used with a metal mesh were investigated. Carbon fiber
12k-prepregs, where carbon fibers were impregnated with epoxy, were
laminated with wire meshes, vacuum bag-molded and hardened to
manufacture hybrid-type specimens, with which an electromagnetic
shield test was performed in accordance with ASTM D4935-10,
through which was known as the most excellent reproducibility is
obtainable among electromagnetic shield tests. In addition, glass fiber
prepregs whose electromagnetic shielding effect were known as
insignificant were laminated and formed with wire meshes to verify
the validity of the electromagnetic shield effect of wire meshes in
order to confirm the electromagnetic shielding effect of metal meshes
corresponding existing carbon fiber 12k-prepregs. By grafting carbon
fibers, on which studies are being actively underway in the
environmental aspects and electromagnetic shielding effect, with
hybrid-type wire meshes that were analysed through the tests, in this
study, the applicability and possibility are proposed.
Abstract: Bacterial strains capable of degradation of malathion
from the domestic sewage were isolated by an enrichment culture
technique. Three bacterial strains were screened and identified as
Acinetobacter baumannii (AFA), Pseudomonas aeruginosa (PS1),
and Pseudomonas mendocina (PS2) based on morphological,
biochemical identification and 16S rRNA sequence analysis.
Acinetobacter baumannii AFA was the most efficient malathion
degrading bacterium, so used for further biodegradation study. AFA
was able to grow in mineral salt medium (MSM) supplemented with
malathion (100 mg/l) as a sole carbon source, and within 14 days,
84% of the initial dose was degraded by the isolate measured by high
performance liquid chromatography. Strain AFA could also degrade
other organophosphorus compounds including diazinon, chlorpyrifos
and fenitrothion. The effect of different culture conditions on the
degradation of malathion like inoculum density, other carbon or
nitrogen sources, temperature and shaking were examined.
Degradation of malathion and bacterial cell growth were accelerated
when culture media were supplemented with yeast extract, glucose
and citrate. The optimum conditions for malathion degradation by
strain AFA were; an inoculum density of 1.5x 10^12CFU/ml at 30°C
with shaking. A specific polymerase chain reaction primers were
designed manually using multiple sequence alignment of the
corresponding carboxylesterase enzymes of Acinetobacter species.
Sequencing result of amplified PCR product and phylogenetic
analysis showed low degree of homology with the other
carboxylesterase enzymes of Acinetobacter strains, so we suggested
that this enzyme is a novel esterase enzyme. Isolated bacterial strains
may have potential role for use in bioremediation of malathion
contaminated.