Abstract: Carbon Capture & Storage (CCS) is one of the various
methods that can be used to reduce the carbon footprint of the
energy sector. This paper focuses on the absorption of CO2 from
flue gas using packed columns, whose efficiency is highly dependent
on the structure of the liquid films within the column. To study the
characteristics of liquid films a CFD solver, OpenFOAM is utilised
to solve two-phase, isothermal film flow using the volume-of-fluid
(VOF) method. The model was validated using existing experimental
data and the Nusselt theory. It was found that smaller plate inclination
angles, with respect to the horizontal plane, resulted in larger wetted
areas on smooth plates. However, only a slight improvement in
the wetted area was observed. Simulations were also performed
using a ridged plate and it was observed that these surface textures
significantly increase the wetted area of the plate. This was mainly
attributed to the channelling effect of the ridges, which helped to
oppose the surface tension forces trying to minimise the surface area.
Rivulet formations on the ridged plate were also flattened out and
spread across a larger proportion of the plate width.
Abstract: In this paper, a bond graph dynamic model for a valvecontrolled
hydraulic cylinder has been developed. A simplified bond
graph model of the inter-actuator interactions in a multi-cylinder
hydraulic system has also been presented. The overall bond graph
model of a valve-controlled hydraulic cylinder was developed by
combining the bond graph sub-models of the pump, spool valve and
the actuator using junction structures. Causality was then assigned
in order to obtain a computational model which could be simulated.
The causal bond graph model of the hydraulic cylinder was verified
by comparing the open loop state responses to those of an ODE
model which had been developed in literature based on the same
assumptions. The results were found to correlate very well both
in the shape of the curves, magnitude and the response times,
thus indicating that the developed model represents the hydraulic
dynamics of a valve-controlled cylinder. A simplified model for interactuator
interaction was presented by connecting an effort source with
constant pump pressure to the zero-junction from which the cylinders
in a multi-cylinder system are supplied with a constant pressure from
the pump. On simulating the state responses of the developed model
under different situations of cylinder operations, indicated that such
a simple model can be used to predict the inter-actuator interactions.
Abstract: This study explored the relationship between
psychological traits, demographics and financial behavioral biases for
individual investors in Taiwan stock market. By using questionnaire
survey method conducted in 2010, there are 554 valid convenient
samples collected to examine the determinants of three types of
behavioral biases. Based on literature review, two hypothesized
models are constructed and further used to evaluate the effects of big
five personality traits and demographic variables on investment biases
through Structural Equation Model (SEM) analysis. The results
showed that investment biases of individual investors are significantly
related to four personality traits as well as some demographics.
Abstract: Transient eddy current problem is solved in the
present paper by the method of the Laplace transform for the case of
a double conductor line located parallel to a conducting half-space.
The Fourier sine and cosine integral transforms are used in order to
find the Laplace transform of the solution. The inverse Laplace
transform of the solution is found in closed form. The integrated
electromotive force per unit length of the double conductor line is
calculated in the form of an improper integral.
Abstract: Single crystals of Magnesium alloys such as Mg-1Al,
Mg-1Zn-0.5Y, Mg-3Li, and AZ31 alloys were successfully fabricated in this study by employing the modified Bridgman method. Single
crystals of pure Mg were also made in this study. To determine the exact orientation of crystals, Laue back-reflection method and pole figure measurement were carried out on each single crystal. Dimensions of single crystals were 10 mm in diameter and 120 mm in
length. Hardness and compression tests were conducted and the results
revealed that hardness and the strength strongly depended on the
orientation. The closer to basal one the orientation was, the higher hardness and compressive strength were. The effect of alloying was
not higher than that of orientation. After compressive deformation of single crystals, the orientation of the crystals was found to rotate and to be parallel to the basal orientation.
Abstract: α-Pinene is the main component of the most
turpentine oils. The hydration of α-pinene with acid catalysts leads to
a complex mixture of monoterpenes. In order to obtain more valuable
products, the α-pinene in the turpentine can be hydrated in dilute
mineral acid solutions to produce α-terpineol. The design of
separation processes requires information on phase equilibrium and
related thermodynamic properties. This paper reports the results of
study on liquid-liquid equilibrium (LLE) of system containing α-
pinene + water and α-terpineol + water.
Binary LLE for α-pinene + water system, and α-terpineol + water
systems were determined by experiment at 301K and atmospheric
pressure. The two component mixture was stirred for about 30min,
then the mixture was left for about 2h for complete phase separation.
The composition of both phases was analyzed by using a Gas
Chromatograph. The experimental data were correlated by
considering both NRTL and UNIQUAC activity coefficient models.
The LLE data for the system of α-pinene + water and α-terpineol +
water were correlated successfully by the NRTL model. The
experimental data were not satisfactorily fitted by the UNIQUAC
model. The NRTL model (α =0.3) correlates the LLE data for the
system of α-pinene + water at 301K with RMSD of 0.0404%. And
the NRTL model (α =0.61) at 301K with RMSD of 0.0058 %. The
NRTL model (α =0.3) correlates the LLE data for the system of α-
terpineol + water at 301K with RMSD of 0.1487% and the NRTL
model (α =0.6) at 301K with RMSD of 0.0032%, between the
experimental and calculated mole fractions.
Abstract: This study mainly aims at assessing the level of
microbial pollution of the water used in the chair system in dental
clinics. For this purpose 36 samples have been randomly collected
from a number of dental surgeries in the city of Tripoli in Libya.
However, 32 of the samples have tested positive to microbial
pollution including 13 of the samples, which have tested positives to
Pseudomonas aeruginosa. Based on the results of the test a further
investigation of the biofilms incorporated within the dental chair
system has been conducted. The laboratory tests of biofilms with
similar design to those found in dental chairs have proved that
bacterial pollution takes place through saliva of the patients who use
the chairs, and that this saliva is rich with nutrients which provides a
suitable breeding ground for all types of bacteria.
Abstract: Reduced switching loss favours Pulse Skipping
Modulation mode of switching dc-to-dc converters at light loads.
Under certain conditions the converter operates in discontinuous
conduction mode (DCM). Inductor current starts from zero in each
switching cycle as the switching frequency is constant and not
adequately high. A DC-to-DC buck converter is modelled and
simulated in this paper under DCM. Effect of ESR of the filter
capacitor in input current frequency components is studied. The
converter is studied for its operation under input voltage and load
variation. The operating frequency is selected to be close to and
above audio range.
Abstract: The Indian subcontinent is facing a massive challenge with regards to the energy security in member countries, i.e. providing a reliable source of electricity to facilitate development across various sectors of the economy and thereby achieve the developmental targets it has set for itself. A highly precarious situation exists in the subcontinent which is observed in the series of system failures which most of the times leads to system collapses-blackouts. To mitigate the issues related with energy security as well as keep in check the increasing supply demand gap, a possible solution that stands in front of the subcontinent is the deployment of an interconnected electricity ‘Supergrid’ designed to carry huge quanta of power across the sub continent as well as provide the infra structure for RES integration. This paper assesses the need and conditions for a Supergrid deployment and consequently proposes a meshed topology based on VSC HVDC converters for the Supergrid modeling.
Abstract: In this paper, a new model predictive PID controller
design method for the slip suppression control of EVs (electric
vehicles) is proposed. The proposed method aims to improve the
maneuverability and the stability of EVs by controlling the wheel
slip ratio. The optimal control gains of PID framework are derived
by the model predictive control (MPC) algorithm. There also include
numerical simulation results to demonstrate the effectiveness of the
method.
Abstract: During last decades, developing multi-objective
evolutionary algorithms for optimization problems has found
considerable attention. Flexible job shop scheduling problem, as an
important scheduling optimization problem, has found this attention
too. However, most of the multi-objective algorithms that are
developed for this problem use nonprofessional approaches. In
another words, most of them combine their objectives and then solve
multi-objective problem through single objective approaches. Of
course, except some scarce researches that uses Pareto-based
algorithms. Therefore, in this paper, a new Pareto-based algorithm
called controlled elitism non-dominated sorting genetic algorithm
(CENSGA) is proposed for the multi-objective FJSP (MOFJSP). Our
considered objectives are makespan, critical machine work load, and
total work load of machines. The proposed algorithm is also
compared with one the best Pareto-based algorithms of the literature
on some multi-objective criteria, statistically.
Abstract: This article proposes a current-mode square-rooting
circuit using current follower transconductance amplifier (CTFA).
The amplitude of the output current can be electronically controlled
via input bias current with wide input dynamic range. The proposed
circuit consists of only single CFTA. Without any matching
conditions and external passive elements, the circuit is then
appropriate for an IC architecture. The magnitude of the output signal
is temperature-insensitive. The PSpice simulation results are
depicted, and the given results agree well with the theoretical
anticipation. The power consumption is approximately 1.96mW at
±1.5V supply voltages.
Abstract: Nowadays e-Learning is more popular, in Vietnam
especially. In e-learning, materials for studying are very important.
It is necessary to design the knowledge base systems and expert
systems which support for searching, querying, solving of
problems. The ontology, which was called Computational Object
Knowledge Base Ontology (COB-ONT), is a useful tool for
designing knowledge base systems in practice. In this paper, a
design method for knowledge base systems in education using
COKB-ONT will be presented. We also present the design of a
knowledge base system that supports studying knowledge and
solving problems in higher mathematics.
Abstract: The amount and heterogeneity of data in biomedical research, notably in interdisciplinary research, requires new methods for the collection, presentation and analysis of information. Important data from laboratory experiments as well as patient trials are available but come out of distributed resources. The Charite Medical School in Berlin has established together with the German Research Foundation (DFG) a new information service center for kidney diseases and transplantation (Open European Nephrology Science Centre - OpEN.SC). The system is based on a service-oriented architecture (SOA) with main and auxiliary modules arranged in four layers. To improve the reuse and efficient arrangement of the services the functionalities are described as business processes using the standardised Business Process Execution Language (BPEL).
Abstract: Academics and researchers are interested in the effects of social media on college students, with a specific focus on the most popular social media website; Facebook. Previous studied have found contradictory result on the relationship between Facebook usage and the student engagement with positive, detrimental and no significant relationships. However, these studies were limited to western higher education system. This paper fills a gap in the literature by using a sample (300) of Sri Lankan management undergraduates to examine the relationship between Facebook usage and student engagement. Student engagement was measured 35 item scale based on the National Survey of Student Engagement and Facebook usage by Facebook intensity scale. Descriptive statistics, path analysis and structural equation modeling were applied as statistical tools and techniques. Results indicate that student engagement scale was significantly negatively related with the Facebook usage with the influence from student engagement on Facebook usage.
Abstract: Student-s movements have been going increasing in
last decades. International students can have different psychological
and sociological problems in their adaptation process. Depression is
one of the most important problems in this procedure. This research
purposed to reveal level of foreign students- depression, kinds of
interpersonal communication networks (host/ethnic interpersonal
communication) and media usage (host/ethnic media usage).
Additionally study aimed to display the relationship between
depression and communication (host/ethnic interpersonal
communication and host/ethnic media usage) among foreign
university students. A field research was performed among 283
foreign university students who have been attending 8 different
universities in Turkey. A purposeful sampling technique was used in
this research cause of data collect facilities. Results indicated that
58.3% of foreign students- depression stage was “intermediate" while
33.2% of foreign students- depression level was “low". Add to this,
host interpersonal communication behaviors and Turkish web sites
usages were negatively and significantly correlated with depression.
Abstract: Among the technologies available to reduce methane
emitted from the pig industry, biofiltration seems to be an effective
and inexpensive solution. In methane (CH4) biofiltration, nitrogen is
an important macronutrient for the microorganisms growth. The
objective of this research project was to study the effect of
ammonium (NH4
+) on the performance, the biomass production and
the nitrogen conversion of a biofilter treating methane. For NH4
+
concentrations ranging from 0.05 to 0.5 gN-NH4
+/L, the CH4 removal
efficiency and the dioxide carbon production rate decreased linearly
from 68 to 11.8 % and from 7.1 to 0.5 g/(m3-h), respectively. The dry
biomass content varied from 4.1 to 5.8 kg/(m3 filter bed). For the
same range of concentrations, the ammonium conversion decreased
while the specific nitrate production rate increased. The specific
nitrate production rate presented negative values indicating
denitrification in the biofilter.
Abstract: This study evaluated the microbiological quality
and the sensory characteristics of carp fillets processed by the
sousvide method when stored at 2 and 10 °C. Four different
combinations of sauced–storage were studied then stored at 2 or 10
°C was evaluate periodically sensory, microbiological and
chemical quality. Batches stored at 2 °C had lower growth rates of
mesophiles and psychrotrophs. Moreover, these counts decreased
by increasing the heating temperature and time. Staphylococcus
aureus, Bacillus cereus, Clostridium perfringens and Listeria
monocytogenes were not found in any of the samples. The heat
treatment of 90 °C for 15 min and sauced was the most effective to
ensure the safety and extend the shelf-life of sousvide carp
preserving its sensory characteristics. This study establishes the
microbiological quality of sous vide carp and emphasizes the
relevance of the raw materials, heat treatment and storage
temperature to ensure the safety of the product.
Abstract: One of the most important secrets of succesful companies is the fact that cooperation with NGOs will create a good reputation for them so that they can be immunized to economic crisis. The performance of the most admired companies in the world based on the ratings of Forbes and Fortune show us that most of these firms also have close relationships with their NGOs. Today, if companies do something wrong this information spreads very quickly to do the society. If people do not like the activities of a company, it can find itself in public relations nightmare that can threaten its repuation. Since the cost of communication has dropped dramatically due to the vast use of internet, the increase in communication among stakeholders via internet makes companies more visible. These multiple and interdependent interactions among the network of stakeholders is called as the network relationships. NGOs play the role of catalyst among the stakeholders of a firm to enhance the awareness. Succesful firms are aware of this fact that NGOs have a central role in today-s business world. Firms are also aware of the fact that they can enhance their corporate reputation via cooperation with the NGOs. This fact will be illustrated in this paper by examining some of the actions of the most succesful companies in terms of their cooperations with the NGOs.
Abstract: A local municipality has decided to build a sewage pit
to receive residential sewage waste arriving by tank trucks. Daily
accumulated waste are to be pumped to a nearby waste water
treatment facility to be re-consumed for agricultural and construction
projects. A discrete-event simulation model using Arena Software
was constructed to assist in defining the capacity of the system in
cubic meters, number of tank trucks to use the system, number of
unload docks required, number of standby areas needed and
manpower required for data collection at entrance checkpoint and
truck tank load toxicity testing. The results of the model are
statistically validated. Simulation turned out to be an excellent tool
in the facility planning effort for the pit project, as it insured smooth
flow lines of tank trucks load discharge and best utilization of
facilities on site.