Abstract: The presence of endocrine-disrupting compounds,
such as bisphenol A (BPA), in the environment can cause serious
health problems. However, there are controversial opinions. This
study investigated the reproductive, metabolic, oxidative and
immunologic-disrupting effects of bisphenol A in male rabbits.
Rabbits were divided into five groups. The first four rabbit groups
were administered oral BPA (1, 10, 50, or 100 mg/kg/day) for ten
weeks. The fifth group was administered corn oil as the vehicle. BPA
significantly decreased serum testosterone, estradiol and the free
androgen index (FAI) and significantly increased sex hormone
binding globulin (SHBG) compared with the placebo group. The
higher doses of BPA showed a significant decrease in follicular
stimulating hormone (FSH) and luteinizing hormone (LH). A
significant increase in blood glucose levels was identified in the BPA
groups. The non-significant difference in insulin levels is a novel
finding. The cumulative testicular toxicity of BPA was clearly
demonstrated by the dose-dependent decrease in absolute testes
weight, primary measures of semen quality and a significant increase
in testicular malonaldehyde (MDA). Moreover, BPA significantly
decreased total antioxidant capacity (TAC) and significantly
increased immunoglobulin G (IgG) at the highest concentration. Our
results suggest that BPA, especially at higher doses, is associated
with many adverse effects on metabolism, oxidative stress, immunity,
sperm quality and markers of androgenic action.
Abstract: In this paper it was examined the influence of margin
regulation on stock market volatility in EU 1993 – 2014. Regulating
margin requirements or haircuts for securities financing transactions
has for a long time been considered as a potential tool to limit the
build-up of leverage and dampen volatility in financial markets. The
margin requirement dictates how much investors can borrow against
these securities. Margin can be an important part of investment.
Using daily and monthly stock returns and there is no convincing
evidence that EU Regulation margin requirements have served to
dampen stock market volatility. In this paper was detected the
expected negative relation between margin requirements and the
amount of margin credit outstanding. Also, it confirmed that changes
in margin requirements by the EU regulation have tended to follow
than lead changes in market volatility. For the analysis have been
used the modified Levene statistics to test whether the standard
deviation of stock returns in the 25, 50 and 100 days preceding
margin changes is the same as that in the succeeding 25, 50 and 100
days. The analysis started in May 1993 when it was first empowered
to set the initial margin requirement and the last sample was in May
2014. To test whether margin requirements influence stock market
volatility over the long term, the sample of stock returns was divided
into 14 periods, according to the 14 changes in margin requirements.
Abstract: The objective of the Economic Dispatch(ED) Problems
of electric power generation is to schedule the committed generating
units outputs so as to meet the required load demand at minimum
operating cost while satisfying all units and system equality and
inequality constraints. This paper presents a new method of ED
problems utilizing the Max-Min Ant System Optimization.
Historically, traditional optimizations techniques have been used,
such as linear and non-linear programming, but within the past
decade the focus has shifted on the utilization of Evolutionary
Algorithms, as an example Genetic Algorithms, Simulated Annealing
and recently Ant Colony Optimization (ACO). In this paper we
introduce the Max-Min Ant System based version of the Ant System.
This algorithm encourages local searching around the best solution
found in each iteration. To show its efficiency and effectiveness, the
proposed Max-Min Ant System is applied to sample ED problems
composed of 4 generators. Comparison to conventional genetic
algorithms is presented.
Abstract: Magnetic powder of Sr-ferrite was prepared by
conventional and sol-gel auto-combustion methods. In conventional
method, strontium carbonate and ferric oxide powders were mixed
together and then mixture was calcined. In sol-gel auto-combustion
method, a solution containing strontium nitrate, ferric nitrate and
citric acid was heated until the combustion took place automatically;
then, as-burnt powder was calcined. Thermal behavior, phase
identification, morphology and magnetic properties of powders
obtained by these two methods were compared by DTA, XRD, SEM
and VSM techniques. According to the results of DTA analysis,
formation temperature of Sr-ferrite obtained by conventional and solgel
auto-combustion methods were 1300°C and 1000°C, respectively.
XRD results confirmed the formation of pure Sr-ferrite at the
mentioned temperatures. Plate and hexagonal-shape particles of Srferrite
were observed using SEM. The Sr-ferrite powder obtained by
sol-gel auto-combustion method had saturation magnetization of
66.03 emu/g and coercivity of 5731 Oe in comparison with values of
58.20 emu/g and 4378 Oe obtained by conventional method.
Abstract: Assertion-Based software testing has been shown to
be a promising tool for generating test cases that reveal program
faults. Because the number of assertions may be very large for
industry-size programs, one of the main concerns to the applicability
of assertion-based testing is the amount of search time required to
explore a large number of assertions. This paper presents a new
approach for assertions exploration during the process of Assertion-
Based software testing. Our initial exterminations with the proposed
approach show that the performance of Assertion-Based testing may
be improved, therefore, making this approach more efficient when
applied on programs with large number of assertions.
Abstract: Climate change would cause mean sea level to rise +1
m by 2100. To prevent coastal floods resulting from the sea level
rising, different flood control structures have been built, with
acceptable protection levels. Gothenburg with the River Göta älv
located on the southwest coast of Sweden is a vulnerable city to the
accelerated rises in mean sea level. We evaluated using a sea barrage
in the River Göta älv to protect Gothenburg during this century. The
highest sea level was estimated to 2.95 m above the current mean sea
level by 2100. To verify flood protection against such high sea levels,
both barriers have to be closed. To prevent high water level in the
River Göta älv reservoir, the barriers would be open when the sea
level is low. The suggested flood control structures would
successfully protect the city from flooding events during this century.
Abstract: Food contamination occurs during post process
handling. This leads to spoilage and growth of pathogenic
microorganisms in the food, thereby reducing its shelf life or
spreading of food borne diseases. Several methods are tried and one
of which is use of antimicrobial packaging. Here, papain, a protease
enzyme, is covalently immobilized with the help of glutarldehyde on
polyurethane and used as a food wrap to protect food from microbial
contamination. Covalent immobilization of papain was achieved at a
pH of 7.4; temperature of 4°C; glutaraldehyde concentration of 0.5%;
incubation time of 24h; and 50mg of papain. The formation of -C=Nobserved
in the Fourier transform infrared spectrum confirmed the
immobilization of the enzyme on the polymer. Immobilized enzyme
retained higher activity than the native free enzyme. The modified
polyurethane showed better reduction of Staphylococcus aureus
biofilm than bare polymer film (eight folds reduction in live colonies,
two times reduction in protein and 6 times reduction in
carbohydrates). The efficacy of this was studied by wrapping it over
S. aureus contaminated cottage cheese (paneer) and cheese and
stored at a temperature of 4°C for 7days. The modified film reduced
the bacterial contamination by eight folds when compared to the bare
film. FTIR also indicated reduction in lipids, sugars and proteins in
the biofilm.
Abstract: Columns have traditionally been constructed of
reinforced concrete or structural steel. Much attention was allocated
to estimate the axial capacity of the traditional column sections to the
detriment of other forms of construction. Other forms of column
construction such as Concrete Filled Double Skin Tubes received
little research attention, and almost no attention when subjected to
eccentric loading. This paper investigates the axial capacity of
columns when subjected to eccentric loading. The experimental axial
capacities are compared to other established theoretical formulae on
concentric loading to determine a possible relationship. The study
found a good correlation between the reduction in axial capacity for
different column lengths and hollow section ratios.
Abstract: Pavement surface unevenness plays a pivotal role on
roughness index of road which affects on riding comfort ability.
Comfort ability refers to the degree of protection offered to vehicle
occupants from uneven elements in the road surface. So, it is
preferable to have a lower roughness index value for a better riding
quality of road users. Roughness is generally defined as an
expression of irregularities in the pavement surface which can be
measured using different equipments like MERLIN, Bump integrator,
Profilometer etc. Among them Bump Integrator is quite simple and
less time consuming in case of long road sections. A case study is
conducted on low volume roads in West District in Tripura to
determine roughness index (RI) using Bump Integrator at the
standard speed of 32 km/h. But it becomes too tough to maintain the
requisite standard speed throughout the road section. The speed of
Bump Integrator (BI) has to lower or higher in some distinctive
situations. So, it becomes necessary to convert these roughness index
values of other speeds to the standard speed of 32 km/h. This paper
highlights on that roughness index conversional model. Using SPSS
(Statistical Package of Social Sciences) software a generalized
equation is derived among the RI value at standard speed of 32 km/h
and RI value at other speed conditions.
Abstract: This paper discusses about the findings of preliminary
survey on MATLAB software learning among power electronics
students. One of the main focuses of power electronics course is on
DC to DC boost convertors, because boost convertors are generally
used in different industrial and non industrial applications. Population
samples of this study were randomly selected final year bachelor of
electronics and electrical engineering students from University Tun
Hussein Onn Malaysia (UTHM).As per the results from the survey
questioner analysis, almost eighty percent students are facing
problem and difficulties in Dc to Dc boost convertors experimental
understanding without using MATLAB simulink package. As per
finding of this study it is clear that MATLAB play an effective and
efficient function for better understanding of boost convertors
experimental work among power electronics learners.
Abstract: This paper explains about the voltage output for DC to
DC boost converter between open loop, PID controller and fuzzy
logic controller through Matlab Simulink. Simulink input voltage was
set at 12V and the voltage reference was set at 24V. The analysis on
the deviation of voltage resulted that the difference between reference
voltage setting and the output voltage is always lower. Comparison
between open loop, PID and FLC shows that, the open loop circuit
having a bit higher on the deviation of voltage. The PID circuit
boosts for FLC has a lesser deviation of voltage and proved that it is
such a better performance on control the deviation of voltage during
the boost mode.
Abstract: The bean (Phaseolus vulgaris L.) is one of the best
known of the legumes, and it has a long cultivation tradition in Italy.
The territory of “Subappennino Dauno” (southern Italy) is at around
700 m a.s.l. and is predominantly grown with cereals, olive trees and
grapevines. Ecotypes of white beans to eat dry (such as cannellini
beans) are also grown, which are sought for their palatability, high
digestibility, and ease of cooking. However, these are not easy to find
on the market due to their low production in relatively small areas
and on small family farms that use seeds handed down from
generation to generation. The introduction of these ecotypes in plain
areas of the Puglia region would provide an opportunity to promote
the diffusion of this type of bean. To investigate the adaptability of
these ecotypes in plain environments (Cerignola, in southern Italy) a
comparative trial was carried out between three ‘Monti Dauni’
ecotypes (E1, E2, E3) that are native to mountain areas and the
similar commercial variety, ‘Cannellini’. The data provide useful
information about the quantitative and qualitative characteristics of
these ecotypes when grown in lowland environments. Ecotype E3
provided the greatest bean production (2.34 t ha-1) compared to
‘Cannellini’ (1.28 t ha-1) and the other ecotypes (0.55 and 0.40 t ha-1,
for E1 and E2, respectively), due to its greater plant growth and the
larger size of the seed (and thickness, in particular). Finally, ecotype
E2 provided the greatest protein content (31.2%), although not
significantly different from the commercial cultivar ‘Cannellini’
(32.1%).
Abstract: This study offers a comprehensive review of the
research papers published in the field of cooling towers and gives an
insight into the latest developments of the natural draught cooling
towers. Different modeling, analysis and design techniques are
summarized and the challenges are discussed. The 118 references
included in this paper are mostly concentrated on the review of the
published papers after 2005. The present paper represents a complete
collection of the studies done for cooling towers and would give an
updated material for the researchers and design engineers in the field
of hyperbolic cooling towers.
Abstract: Through this paper we present a method for automatic
generation of ontological model from any data source using Model
Driven Architecture (MDA), this generation is dedicated to the
cooperation of the knowledge engineering and software engineering.
Indeed, reverse engineering of a data source generates a software
model (schema of data) that will undergo transformations to generate
the ontological model. This method uses the meta-models to validate
software and ontological models.
Abstract: Curcuma longa L. (Zingiberaceae), commonly known
as turmeric, has a long history of traditional uses for culinary
purposes as a spice and a food colorant. The present study aimed to
document the ethnobotanical knowledge about Curcuma longa, and
to assess the variation in the herbalists’ experience in Northeastern
Algeria. Data were collected using semi-structured questionnaires
and direct interviews with 30 herbalists. Ethnobotanical indices,
including the fidelity level (FL%), the relative frequency citation
(RFC), and use value (UV) were determined by quantitative methods.
Diversity in the level of knowledge was analyzed using univariate,
non-parametric, and multivariate statistical methods. Three main
categories of uses were recorded for C. longa: for food, for medicine,
and for cosmetic purposes. As a medicine, turmeric was used for the
treatment of gastrointestinal, dermatological, and hepatic diseases.
Medicinal and food uses were correlated with both forms of
preparation (rhizome and powder). The age group did not influence
the use. Multivariate analyses showed a significant variation in
traditional knowledge, associated with the use value, origin, quality,
and efficacy of the drug. The findings suggested that the geographical
origin of C. longa affected the use in Algeria.
Abstract: The effective development of a geoscience education
and training program takes account of the rapidly changing
environment in the geoscience market, includes information about
resource-rich countries which have international education demands.
In this paper, we introduce the geoscience program run by the
International School for Geoscience Resources at the Korea Institute
of Geoscience and Mineral Resources (IS-Geo of KIGAM), and show
its remarkable performance. To further effective geoscience program
planning and operation, we present recommendations for strategic
management for customer-oriented operation with a more favorable
program format and advanced training aids. Above all, the IS-Geo of
KIGAM should continue improve through ‘plan-do-see-feedback’
activities based on the recommendations.
Abstract: The use of information and communication
technologies such as computers, mobile phones and the Internet is
becoming prevalent in today’s world; and it is facilitating access to a
vast amount of data, services and applications for the improvement of
people’s lives. However, this prevalence of ICTs is hampered by the
problem of low income levels in developing countries to the point
where people cannot timeously replace or repair their ICT devices
when damaged or lost; and this problem serves as a motivation for
this study whose aim is to examine the perceptions of teachers on the
reliability of cellphones when used for teaching and learning
purposes. The research objectives unfolding this aim are of two
types: Objectives on the selection and design of theories and models,
and objectives on the empirical testing of these theories and models.
The first type of objectives is achieved using content analysis in an
extensive literature survey: and the second type of objectives is
achieved through a survey of high school teachers from the ILembe
and UMgungundlovu districts in the KwaZulu-Natal province of
South Africa. Data collected from this questionnaire based survey is
analysed in SPSS using descriptive statistics and Pearson correlations
after checking the reliability and validity of the questionnaires. The
main hypothesis driving this study is that there is a relationship
between the demographics and the attribution identity of teachers on
one hand, and their perceptions on the reliability of cellphones on the
other hand, as suggested by existing literature; except that attribution
identities are considered in this study under three angles: intention,
knowledge and ability, and action. The results of this study confirm
that the perceptions of teachers on the reliability of cellphones for
teaching and learning are affected by the school location of these
teachers, and by their perceptions on learners’ cellphones usage
intentions and actual use.
Abstract: The handwriting is a physical demonstration of a
complex cognitive process learnt by man since his childhood. People
with disabilities or suffering from various neurological diseases are
facing so many difficulties resulting from problems located at the
muscle stimuli (EMG) or signals from the brain (EEG) and which
arise at the stage of writing. The handwriting velocity of the same
writer or different writers varies according to different criteria: age,
attitude, mood, writing surface, etc. Therefore, it is interesting to
reconstruct an experimental basis records taking, as primary
reference, the writing speed for different writers which would allow
studying the global system during handwriting process. This paper
deals with a new approach of the handwriting system modeling based
on the velocity criterion through the concepts of artificial neural
networks, precisely the Radial Basis Functions (RBF) neural
networks. The obtained simulation results show a satisfactory
agreement between responses of the developed neural model and the
experimental data for various letters and forms then the efficiency of
the proposed approaches.
Abstract: At-site flood frequency analysis is used to estimate
flood quantiles when at-site record length is reasonably long. In
Australia, FLIKE software has been introduced for at-site flood
frequency analysis. The advantage of FLIKE is that, for a given
application, the user can compare a number of most commonly
adopted probability distributions and parameter estimation methods
relatively quickly using a windows interface. The new version of
FLIKE has been incorporated with the multiple Grubbs and Beck test
which can identify multiple numbers of potentially influential low
flows. This paper presents a case study considering six catchments in
eastern Australia which compares two outlier identification tests
(original Grubbs and Beck test and multiple Grubbs and Beck test)
and two commonly applied probability distributions (Generalized
Extreme Value (GEV) and Log Pearson type 3 (LP3)) using FLIKE
software. It has been found that the multiple Grubbs and Beck test
when used with LP3 distribution provides more accurate flood
quantile estimates than when LP3 distribution is used with the
original Grubbs and Beck test. Between these two methods, the
differences in flood quantile estimates have been found to be up to
61% for the six study catchments. It has also been found that GEV
distribution (with L moments) and LP3 distribution with the multiple
Grubbs and Beck test provide quite similar results in most of the
cases; however, a difference up to 38% has been noted for flood
quantiles for annual exceedance probability (AEP) of 1 in 100 for one
catchment. This finding needs to be confirmed with a greater number
of stations across other Australian states.
Abstract: Present study is aimed on the cutting process of circular
cross-section rods where the fracture is used to separate one rod
into two pieces. Incorporating the phenomenological ductile fracture
model into the explicit formulation of finite element method, the
process can be analyzed without the necessity of realizing too many
real experiments which could be expensive in case of repetitive
testing in different conditions. In the present paper, the steel AISI
1045 was examined and the tensile tests of smooth and notched
cylindrical bars were conducted together with biaxial testing of the
notched tube specimens to calibrate material constants of selected
phenomenological ductile fracture models. These were implemented
into the Abaqus/Explicit through user subroutine VUMAT and used
for cutting process simulation. As the calibration process is based
on variables which cannot be obtained directly from experiments,
numerical simulations of fracture tests are inevitable part of the
calibration. Finally, experiments regarding the cutting process were
carried out and predictive capability of selected fracture models is
discussed. Concluding remarks then make the summary of gained
experience both with the calibration and application of particular
ductile fracture criteria.