Abstract: The separation of Hg (II) from produced water by
hollow fiber contactors (HFC) was investigation. This system
included of two hollow fiber modules in the series connecting. The
first module used for the extraction reaction and the second module
for stripping reaction. Aliquat336 extractant was fed from the organic
reservoirs into the shell side of the first hollow fiber module and
continuous to the shell side of the second module. The organic liquid
was continuously feed recirculate and back to the reservoirs. The feed
solution was pumped into the lumen (tube side) of the first hollow
fiber module. Simultaneously, the stripping solution was pumped in
the same way in tube side of the second module. The feed and
stripping solution was fed which had a countercurrent flow. Samples
were kept in the outlet of feed and stripping solution at 1 hour and
characterized concentration of Hg (II) by Inductively Couple Plasma
Atomic Emission Spectroscopy (ICP-AES). Feed solution was
produced water from natural gulf of Thailand. The extractant was
Aliquat336 dissolved in kerosene diluent. Stripping solution used was
nitric acid (HNO3) and thiourea (NH2CSNH2). The effect of carrier
concentration and type of stripping solution were investigated.
Results showed that the best condition were 10 % (v/v) Aliquat336
and 1.0 M NH2CSNH2. At the optimum condition, the extraction and
stripping of Hg (II) were 98% and 44.2%, respectively.
Abstract: Dielectric ceramic samples in the BaO-Re2O3-TiO2
ternary system were synthesized with structural formula Ba2-
xRe4+2x/3Ti8O24 where Re= rare earth metal and Re= Sm and La where
x varies from 0.0 to 0.6 with step size 0.1. Polycrystalline samples
were prepared by the conventional solid state reaction technique. The
dielectric, electrical and impedance analysis of all the samples in the
frequency range 1KHz- 1MHz at room temperature (25°C) have been
done to get the understanding of electrical conduction and dielectric
relaxation and their correlation. Dielectric response of the samples at
lower frequencies shows dielectric dispersion while at higher
frequencies it shows dielectric relaxation. The ac conductivity is well
fitted by the Jonscher law. The spectroscopic data in the impedance
plane confirms the existence of grain contribution to the relaxation.
All the properties are found out to be function of frequency as well as
the amount of substitution.
Abstract: This paper examines the utilization of public-private
partnerships for the building and operation of wastewater treatment
plants. Our research focuses on risk allocation in this kind of projects.
Our analysis builds on more than hundred wastewater treatment
plants built and operated through PPP projects in Aragon (Spain).
The paper illustrates the consequences of an inadequate management
of construction risk and an unsuitable transfer of demand risk in
wastewater treatment plants. It also shows that the involvement of
many public bodies at local, regional and national level further
increases the complexity of this kind of projects and make time
delays more likely.
Abstract: Waste load allocation (WLA) policies may use multiobjective
optimization methods to find the most appropriate and
sustainable solutions. These usually intend to simultaneously
minimize two criteria, total abatement costs (TC) and environmental
violations (EV). If other criteria, such as inequity, need for
minimization as well, it requires introducing more binary
optimizations through different scenarios. In order to reduce the
calculation steps, this study presents value index as an innovative
decision making approach. Since the value index contains both the
environmental violation and treatment costs, it can be maximized
simultaneously with the equity index. It implies that the definition of
different scenarios for environmental violations is no longer required.
Furthermore, the solution is not necessarily the point with minimized
total costs or environmental violations. This idea is testified for Haraz
River, in north of Iran. Here, the dissolved oxygen (DO) level of river
is simulated by Streeter-Phelps equation in MATLAB software. The
WLA is determined for fish farms using multi-objective particle
swarm optimization (MOPSO) in two scenarios. At first, the trade-off
curves of TC-EV and TC-Inequity are plotted separately as the
conventional approach. In the second, the Value-Equity curve is
derived. The comparative results show that the solutions are in a
similar range of inequity with lower total costs. This is due to the
freedom of environmental violation attained in value index. As a
result, the conventional approach can well be replaced by the value
index particularly for problems optimizing these objectives. This
reduces the process to achieve the best solutions and may find better
classification for scenario definition. It is also concluded that decision
makers are better to focus on value index and weighting its contents
to find the most sustainable alternatives based on their requirements.
Abstract: The need to use high volumes of data and the high
competition are only two reasons which make necessary the use of
information technologies. The objective of our research is to establish
the impact of information technologies on the accounting department
of the Romanian companies. In order to achieve it, starting from the
literature review we made an empirical research based on a
questionnaire. We investigated the types of technologies used, the
reasons which led to the implementation of certain technologies, the
benefits brought by the use of the information technologies, the
difficulties brought by the implementation and the future effects of
the applications. The conclusions show that there is an evolution in
the degree of implementation of the information technologies in the
Romanian companies, compared with the results of other studies
conducted a few years before.
Abstract: Quantitative radiobiological models can be used to
assess the optimum clinical outcome from sophisticated therapeutic
modalities by calculating tumor control probability (TCP) and normal
tissue complication probability (NTCP). In this study two 3D-CRT
and an IMRT treatment plans were developed with an initial
prescription dose of 60 Gy in 2 Gy/fraction to prostate. Sensitivity of
TCP and Complication free tumor control probability (P+) to the
different values of α/β ratio was investigated for various prescription
doses planned to be delivered in either a fixed number of fractions (I)
or in a fixed dose per fraction (II) in each of the three different
treatment plans. High dose/fraction and high α/β value result in
comparatively smaller P+ and IMRT plans resulted in the highest P+,
mainly due to the decrease in NTCP. If α/β is lower than expected,
better tumor control can be achieved by increasing dose/fraction but
decreasing the number of fractions.
Abstract: Medicinal plants are now gaining attractiveness in
treatment of bacterial infections and food preservation. The objective
of this study was to assess antibacterial activity of some medicinal
plants on pathogenic bacteria. Screening of antibacterial activity of
aqueous and methanol extracts of some plants: Jojoba, Ginger, Sage,
Thyme and Clove against Bacillus cereus, Salmonella typhimurium,
Staphylococcus aureus, Clostridium perfringens and Escherichia coli
were investigated. Antibacterial activity was performed by agar
diffusion and disc diffusion method. Jatropha, Jojoba, Clove and
Ginger extracts showed notable bacterial activity in the first
screening step then selected to be tested against Bacillus cereus
(Gram+), Staphylococcus aureus (Gram+) and Salmonella
typhimurium (Gram−) and their effect was compared using
antibiotics as control. Screening results showed potential antibacterial
activity of the tested plant extracts against the screened bacterial
strains. It was found that methanol extracts exhibited higher
antibacterial activity than aqueous extracts. Methanol extract of
Jatropha showed the highest inhibition zone against Staphylococcus
aureus (Gram+) with 24.00 mm diameter, compared to the other
plant extracts followed by clove. Meanwhile, the inhibition zones of
methanol extracts of Jojoba and Ginger were the same (12mm).The
Gram-positive bacteria were found to be more sensitive to aqueous
and methanol extracts than Gram-negative bacteria.
Abstract: In this research article of modeling Underwater
Wireless Sensor Network Simulators, we provide a comprehensive
overview of the various currently available simulators used in UWSN
modeling. In this work, we compare their working environment,
software platform, simulation language, key features, limitations and
corresponding applications. Based on extensive experimentation and
performance analysis, we provide their efficiency for specific
applications. We have also provided guidelines for developing
protocols in different layers of the protocol stack, and finally these
parameters are also compared and tabulated. This analysis is
significant for researchers and designers to find the right simulator
for their research activities.
Abstract: This paper analyses the heat transfer performance and
fluid flow using different nanofluids in a square enclosure. The
energy equation and Navier-Stokes equation are solved numerically
using finite volume scheme. The effect of volume fraction
concentration on the enhancement of heat transfer has been studied
icorporating the Brownian motion; the influence of effective thermal
conductivity on the enhancement was also investigated for a range of
volume fraction concentration. The velocity profile for different
Rayleigh number. Water-Cu, water AL2O3 and water-TiO2 were
tested.
Abstract: The article presents a plasma chemical technology for
processing solid fuels, using examples of bituminous and brown
coals. Thermodynamic and experimental investigation of the
technology was made. The technology allows producing synthesis
gas from the coal organic mass and valuable components (technical
silicon, ferrosilicon, aluminum, and carbon silicon, as well as
microelements of rare metals, such as uranium, molybdenum,
vanadium, etc.) from the mineral mass. The thusly produced highcalorific
synthesis gas can be used for synthesis of methanol, as a
high-calorific reducing gas instead of blast-furnace coke as well as
power gas for thermal power plants.
Abstract: We propose new multiple-channel piezoelectric (PZT)
actuated tunable optical filter based on racetrack multi-ring
resonators for wavelength de-multiplexing network applications. We
design tunable eight-channel wavelength de-multiplexer consisting of
eight cascaded PZT actuated tunable multi-ring resonator filter with a
channel spacing of 1.6nm. The filter for each channel is basically
structured on a suspended beam, sandwiched with piezoelectric
material and built in integrated ring resonators which are placed on
the middle of the beam to gain uniform stress and linearly varying
longitudinal strain. A reference single mode serially coupled multi
stage racetrack ring resonator with the same radii and coupling length
is designed with a line width of 0.8974nm with a flat top pass band at
1dB of 0.5205nm and free spectral range of about 14.9nm. In each
channel, a small change in the perimeter of the rings is introduced to
establish the shift in resonance wavelength as per the defined channel
spacing. As a result, when a DC voltage is applied, the beams will
elongate, which involves mechanical deformation of the ring
resonators that induces a stress and a strain, which brings a change in
refractive index and perimeter of the rings leading to change in the
output spectrum shift providing the tunability of central wavelength
in each channel. Simultaneous wave length shift as high as
45.54pm/
Abstract: In wastewater treatment processes, aeration introduces
air into a liquid. In these systems, air is introduced by different
devices submerged in the wastewater. Smaller bubbles result in more
bubble surface area per unit of volume and higher oxygen transfer
efficiency. Jet pumps are devices that use air bubbles and are widely
used in wastewater treatment processes. The principle of jet pumps is
their ability to transfer energy of one fluid, called primary or motive,
into a secondary fluid or gas. These pumps have no moving parts and
are able to work in remote areas under extreme conditions. The
objective of this work is to study experimentally the characteristics of
the jet pump and the size of air bubbles in the laboratory water tank.
The effect of flow rate ratio on pump performance is investigated in
order to have a better understanding about pump behavior under
various conditions, in order to determine the efficiency of receiving
air bubbles different sizes. The experiments show that we should take
care when increasing the flow rate ratio while seeking to decrease
bubble size in the outlet flow. This study will help improve and
extend the use of the jet pump in many practical applications.
Abstract: Many industrial materials like magnets need to be
tested for the radiation environment expected at linear colliders (LC)
where the accelerator and detectors will be subjected to large
influences of beta, neutron and gamma’s over their life Gamma
irradiation of the permanent sample magnets using a 60Co source was
investigated up to an absorbed dose of 700Mrad shows a negligible
effect on some magnetic properties of Nd-Fe-B. In this work it has
been tried to investigate the change of some important properties of
Barium hexa ferrite. Results showed little decreases of magnetic
properties at doses rang of 0.5 to 2.5 Mrad. But at the gamma
irradiation dose up to 10 Mrad it is showed a few increase of
properties. Also study of gamma irradiation of Nd-Fe-B showed
considerably increase of magnetic properties.
Abstract: One of the most famous techniques which affect the
efficiency of a production line is the assembly line balancing (ALB)
technique. This paper examines the balancing effect of a whole
production line of a real auto glass manufacturer in three steps. In the
first step, processing time of each activity in the workstations is
generated according to a practical approach. In the second step, the
whole production process is simulated and the bottleneck stations
have been identified, and finally in the third step, several
improvement scenarios are generated to optimize the system
throughput, and the best one is proposed. The main contribution of
the current research is the proposed framework which combines two
famous approaches including Assembly Line Balancing and
Optimization via Simulation technique (OvS). The results show that
the proposed framework could be applied in practical environments,
easily.
Abstract: The secondary alloy A226 is used for many
automotive casting produced by mould casting and high pressure die
casting. This alloy has excellent castability, good mechanical
properties and cost-effectiveness. Production of primary aluminium
alloys belong to heavy source fouling of life environs. The European
Union calls for the emission reduction and reduction in energy
consumption therefore increase production of recycled (secondary)
aluminium cast alloys. The contribution is deal with influence of
recycling on the quality of the casting made from A226 in automotive
industry. The properties of the casting made from secondary
aluminium alloys were compared with the required properties of
primary aluminium alloys. The effect of recycling on microstructure
was observed using combination different analytical techniques (light
microscopy upon black-white etching, scanning electron microscopy
- SEM upon deep etching and energy dispersive X-ray analysis -
EDX). These techniques were used for the identification of the
various structure parameters, which was used to compare secondary
alloy microstructure with primary alloy microstructure.
Abstract: Many factors influence the educational outcome of
students. Some of these have been studied by researchers with many
emphasizing the role of students, schools, governments, peer groups
and so on. More often than not, some of these factors influencing the
academic achievement of the students have been traced back to
parents and family; being the primary platform on which learning not
only begins but is nurtured, encouraged and developed which later
transforms to the performance of the students. This study not only
explores parental and related factors that predict academic
achievement through the review of relevant literatures but also,
investigates the influence of parental background on the academic
achievement of senior secondary school students in Ibadan North
Local Government Area of Oyo State, Nigeria. As one of the criteria
of the quality of education, students’ academic achievement was
investigated because it is most often cited as an indicator of school
effectiveness by school authorities and educationists. The data
collection was done through interviews and use of well-structured
questionnaires administered to one hundred students (100) within the
target local government. This was statistically analysed and the result
showed that parents’ attitudes towards their children’s education had
significant effect(s) on students’ self-reporting of academic
achievement. However, such factors as parental education and socioeconomic
background had no significant relationship with the
students’ self-reporting of academic achievement.
Abstract: The iron environment in Fe-doped Vycor Anode was
investigated with EXAFS using Brookhaven Synchrotron Light
Source. The iron-reducing Shewanella oneidensis culture was grown
in a microbial fuel cell under anaerobic respiration. The Fe bond
length was found to decrease and correlate with the amount of
biofilm growth on the Fe-doped Vycor Anode. The data suggests that
Fe-doped Vycor Anode would be a good substrate to study the
Shewanella oneidensis nanowire structure using EXAFS.
Abstract: The arsenic and iron environments in different growth
stages have been studied with EXAFS and XANES using
Brookhaven Synchrotron Light Source. Collard Greens plants were
grown and tissue samples were harvested. The project studied the
EXAFS and XANES of tissue samples using As and Fe K-edges. The
Fe absorption and the Fourier transform bond length information
were used as a control comparison. The Fourier transform of the
XAFS data revealed the coexistence of As (III) and As (V) in the As
bonding environment inside the studied plant tissue samples,
although the soil only had As (III). The data suggests that Collard
Greens has a novel pathway to handle arsenic absorption in soil.
Abstract: The aim of this paper is to present the concept of an
agile enterprise model and to initiate discussion on the research
assumptions of the model presented. The implementation of the
research project "The agility of enterprises in the process of adapting
to the environment and its changes" began in August 2014 and is
planned to last three years. The article has the form of a work-inprogress
paper which aims to verify and initiate a debate over the
proposed research model. In the literature there are very few
publications relating to research into agility; it can be concluded that
the most controversial issue in this regard is the method of measuring
agility. In previous studies the operationalization of agility was often
fragmentary, focusing only on selected areas of agility, for example
manufacturing, or analysing only selected sectors. As a result the
measures created to date can only be treated as contributory to the
development of precise measurement tools. This research project
aims to fill a cognitive gap in the literature with regard to the
conceptualization and operationalization of an agile company. Thus,
the original contribution of the author of this project is the
construction of a theoretical model that integrates manufacturing
agility (consisting mainly in adaptation to the environment) and
strategic agility (based on proactive measures). The author of this
research project is primarily interested in the attributes of an agile
enterprise which indicate that the company is able to rapidly adapt to
changing circumstances and behave pro-actively.
Abstract: With the flourishing development of online shopping,
an increasing number of customers see online shopping as an
entertaining experience. Because the online consumer has a double
identity as a shopper and an Internet user, online shopping should offer
hedonic values of shopping and Internet usage. The purpose of this
study is to investigate hedonic online shopping motivations from the
perspectives of traditional hedonic value and flow theory.
The study adopted a focus group interview method, including two
online and two offline interviews. Four focus groups of shoppers
consisted of online professionals, online college students, offline
professionals and offline college students. The results of the study
indicate that traditional hedonic values and dimensions of flow theory
exist in the online shopping environment. The study indicated that
online shoppers seem to appreciate being able to learn things and grow
to become competitive achievers online. Comparisons of online
hedonic motivations between groups are conducted. This study serves
as a basis for the future growth of Internet marketing.