Abstract: Vehicle detection is the critical step for highway monitoring. In this paper we propose background subtraction and edge detection technique for vehicle detection. This technique uses the advantages of both approaches. The practical applications approved the effectiveness of this method. This method consists of two procedures: First, automatic background extraction procedure, in which the background is extracted automatically from the successive frames; Second vehicles detection procedure, which depend on edge detection and background subtraction. Experimental results show the effective application of this algorithm. Vehicles detection rate was higher than 91%.
Abstract: In this article, the phenomenon of nonlinear
consolidation in saturated and homogeneous clay layer is studied.
Considering time-varied drainage model, the excess pore water
pressure in the layer depth is calculated. The Generalized Differential
Quadrature (GDQ) method is used for the modeling and numerical
analysis. For the purpose of analysis, first the domain of independent
variables (i.e., time and clay layer depth) is discretized by the
Chebyshev-Gauss-Lobatto series and then the nonlinear system of
equations obtained from the GDQ method is solved by means of the
Newton-Raphson approach. The obtained results indicate that the
Generalized Differential Quadrature method, in addition to being
simple to apply, enjoys a very high accuracy in the calculation of
excess pore water pressure.
Abstract: Managing knowledge of research is one way to ensure
just in time information and knowledge to support research strategist
and activities. Unfortunately researcher found the vital research
knowledge in IHL (Institutions of Higher Learning) are scattered,
unstructured and unorganized. Aiming on lay aside conceptual
foundations for understanding and developing OMS (Organizational
Memory System) to facilitate research in IHL, this research revealed
ten factors contributed to the needs of research in the IHL and seven
internal challenges of IHL in promoting research to their academic
members. This study then suggested a comprehensive support of
managing research knowledge using Organizational Memory System
(OMS). Eight OMS characteristics to support research were
identified. Finally the initial work in designing OMS was projected
using knowledge taxonomy. All analysis is derived from pertinent
research paper related to research in IHL and OMS. Further study can
be conducted to validate and verify results presented.
Abstract: Software projects are very dynamic and require
recurring adjustments of their project plans. These settings can be
understood as reconfigurations in the schedule, in the resources
allocation and other design elements. Yet, during the planning and
execution of a software project, the integration of specific activities
in the projects with the activities that take part in the organization-s
common activity flow should be considered. This article presents the
results from a systematic review of aspects related to software
projects- dynamic reconfiguration emphasizing the integration of
project management with the organizational flows. A series of studies
was analyzed from the year 2000 to the present. The results of this
work show that there is a diversity of techniques and strategies for
dynamic reconfiguration of software projects-. However, few
approaches consider the integration of software project activities with
the activities that take part in the organization-s common workflow.
Abstract: A research program is conducted to evaluate the
mechanical properties of Ultra High Performance Concrete, target
compressive strength at the age of 28 days being more than 150 MPa.
The methodology to develop such mix has been explained. The
material properties, mix design and curing regime are determined.
The material attributes are understood by studying the stress strain
behaviour of UHPC cylinders under uniaxial compressive loading.
The load –crack mouth opening displacement (cmod) of UHPC
beams, flexural strength and fracture energy was evaluated using
third point loading test. Compressive strength and Split tensile
strength results are determined to find out the compressive and tensile
behaviour. Residual strength parameters are presented vividly
explaining the flexural performance, toughness of concrete.Durability
studies were also done to compare the effect of fibre to that of a
control mix For all the studies the Mechanical properties were
evaluated by varying the percentage and aspect ratio of steel fibres
The results reflected that higher aspect ratio and fibre volume
produced drastic changes in the cube strength, cylinder strength, post
peak response, load-cmod, fracture energy flexural strength, split
tensile strength, residual strength and durability. In regards to null
application of UHPC in India, an initiative is undertaken to
comprehend the mechanical behaviour of UHPC, which will be vital
for longer run in commercialization for structural applications.
Abstract: Knowledge Discovery in Databases (KDD) has
evolved into an important and active area of research because of
theoretical challenges and practical applications associated with the
problem of discovering (or extracting) interesting and previously
unknown knowledge from very large real-world databases. Rough
Set Theory (RST) is a mathematical formalism for representing
uncertainty that can be considered an extension of the classical set
theory. It has been used in many different research areas, including
those related to inductive machine learning and reduction of
knowledge in knowledge-based systems. One important concept
related to RST is that of a rough relation. In this paper we presented
the current status of research on applying rough set theory to KDD,
which will be helpful for handle the characteristics of real-world
databases. The main aim is to show how rough set and rough set
analysis can be effectively used to extract knowledge from large
databases.
Abstract: The study explored varied types of human smiles and
extracted most of the key factors affecting the smiles. These key
factors then were converted into a set of control points which could
serve to satisfy the needs for creation of facial expression for 3D
animators and be further applied to the face simulation for robots in the
future. First, hundreds of human smile pictures were collected and
analyzed to identify the key factors for face expression. Then, the
factors were converted into a set of control points and sizing
parameters calculated proportionally. Finally, two different faces
were constructed for validating the parameters via the process of
simulating smiles of the same type as the original one.
Abstract: With the exponential progress of technological
development comes a strong sense that events are moving too quickly
for our schools and that teachers may be losing control of them in the
process. This paper examines the impact of e-learning and e-teaching
in universities, from both the student and teacher perspective. In
particular, it is shown that e-teachers should focus not only on the
technical capacities and functions of IT materials and activities, but
must attempt to more fully understand how their e-learners perceive
the learning environment. From the e-learner perspective, this paper
indicates that simply having IT tools available does not automatically
translate into all students becoming effective learners. More
evidence-based evaluative research is needed to allow e-learning and
e-teaching to reach full potential.
Abstract: According as the Architecture, Engineering and Construction (AEC) Industry projects have grown more complex and larger, the number of utilization of BIM for 3D design and simulation is increasing significantly. Therefore, typical applications of BIM such as clash detection and alternative measures based on 3-dimenstional planning are expanded to process management, cost and quantity management, structural analysis, check for regulation, and various domains for virtual design and construction. Presently, commercial BIM software is operated on single-user environment, so initial cost is so high and the investment may be wasted frequently. Cloud computing that is a next-generation internet technology enables simple internet devices (such as PC, Tablet, Smart phone etc) to use services and resources of BIM software. In this paper, we suggested developing method of the BIM software based on cloud computing environment in order to expand utilization of BIM and reduce cost of BIM software. First, for the benchmarking, we surveyed successful case of BIM and cloud computing. And we analyzed needs and opportunities of BIM and cloud computing in AEC Industry. Finally, we suggested main functions of BIM software based on cloud computing environment and developed a simple prototype of cloud computing BIM software for basic BIM model viewing.
Abstract: System-level design based on high-level abstractions
is becoming increasingly important in hardware and embedded
system design. This paper analyzes meta-design techniques oriented
at developing meta-programs and meta-models for well-understood
domains. Meta-design techniques include meta-programming and
meta-modeling. At the programming level of design process, metadesign
means developing generic components that are usable in a
wider context of application than original domain components. At the
modeling level, meta-design means developing design patterns that
describe general solutions to the common recurring design problems,
and meta-models that describe the relationship between different
types of design models and abstractions. The paper describes and
evaluates the implementation of meta-design in hardware design
domain using object-oriented and meta-programming techniques.
The presented ideas are illustrated with a case study.
Abstract: The counting and analysis of blood cells allows the
evaluation and diagnosis of a vast number of diseases. In particular,
the analysis of white blood cells (WBCs) is a topic of great interest to
hematologists. Nowadays the morphological analysis of blood cells is
performed manually by skilled operators. This involves numerous
drawbacks, such as slowness of the analysis and a nonstandard
accuracy, dependent on the operator skills. In literature there are only
few examples of automated systems in order to analyze the white
blood cells, most of which only partial. This paper presents a
complete and fully automatic method for white blood cells
identification from microscopic images. The proposed method firstly
individuates white blood cells from which, subsequently, nucleus and
cytoplasm are extracted. The whole work has been developed using
MATLAB environment, in particular the Image Processing Toolbox.
Abstract: The purpose of this study was to develop and examine a
Teaching Commitment Scale of Health and Physical Education
(TCS-HPE) for Taiwanese elementary school teachers. First of all,
based on teaching commitment related theory and literatures to
develop a original scale with 40 items, later both stratified random
sampling and cluster sampling were used to sample participants.
During the first stage, 300 teachers were sampled and 251 valid scales
(83.7%) returned. Later, the data was analyzed by exploratory factor
analysis to obtain 74.30% of total variance for the construct validity.
The Cronbach-s alpha coefficient of sum scale reliability was 0.94, and
subscale coefficients were between 0.80 and 0.96. In the second stage,
400 teachers were sampled and 318 valid scales (79.5%) returned.
Finally, this study used confirmatory factor analysis to test validity and
reliability of TCS-HPE. The result showed that the fit indexes reached
acceptable criteria(¤ç2
(246 ) =557.64 , p
Abstract: The present study deals with the analysis of the cylindrical part of a CNG storage vessel, combining a plastic liner and an over wrapped filament wound composite. Three kind of polymer are used in the present analysis: High density Polyethylene HDPE, Light low density Polyethylene LLDPE and finally blend of LLDPE/HDPE. The effect of the mechanical properties on the behavior of type IV vessel may be then investigated. In the present paper, the effect of the order of the circumferential winding on the stacking sequence may be then investigated. Based on mechanical considerations, the present model provides an exact solution for stresses and deformations on the cylindrical section of the vessel under thermo-mechanical static loading. The result show a good behavior of HDPE liner compared to the other plastic materials. The presence of circumferential winding angle in the stacking improves the rigidity of vessel by improving the burst pressure.
Abstract: Electrocardiogram (ECG) is considered to be the
backbone of cardiology. ECG is composed of P, QRS & T waves and
information related to cardiac diseases can be extracted from the
intervals and amplitudes of these waves. The first step in extracting
ECG features starts from the accurate detection of R peaks in the
QRS complex. We have developed a robust R wave detector using
wavelets. The wavelets used for detection are Daubechies and
Symmetric. The method does not require any preprocessing therefore,
only needs the ECG correct recordings while implementing the
detection. The database has been collected from MIT-BIH arrhythmia
database and the signals from Lead-II have been analyzed. MatLab
7.0 has been used to develop the algorithm. The ECG signal under
test has been decomposed to the required level using the selected
wavelet and the selection of detail coefficient d4 has been done based
on energy, frequency and cross-correlation analysis of decomposition
structure of ECG signal. The robustness of the method is apparent
from the obtained results.
Abstract: In today-s turbulent environment, companies are faced with two principal challenges. On the one hand, it is necessary to produce ever more cost-effectively to remain competitive. On the other hand, factories need to be transformable in order to manage unpredictable changes in the corporate environment. To deal with these different challenges, companies use the philosophy of lean production in the first case, in the second case the philosophy of transformability. To a certain extent these two approaches follow different directions. This can cause conflicts when designing factories. Therefore, the Institute of Production Systems and Logistics (IFA) of the Leibniz University of Hanover has developed a procedure to allow companies to evaluate and design their factories with respect to the requirements of both philosophies.
Abstract: An empirical study of web applications that use
software frameworks is presented here. The analysis is based on two
approaches. In the first, developers using such frameworks are
required, based on their experience, to assign weights to parameters
such as database connection. In the second approach, a performance
testing tool, OpenSTA, is used to compute start time and other such
measures. From such an analysis, it is concluded that open source
software is superior to proprietary software. The motivation behind
this research is to examine ways in which a quantitative assessment
can be made of software in general and frameworks in particular.
Concepts such as metrics and architectural styles are discussed along
with previously published research.
Abstract: The hand is one of the essential parts of the body for
carrying out Activities of Daily Living (ADLs). Individuals use their
hands and fingers in everyday activities in the both the workplace
and home. Hand-intensive tasks require diverse and sometimes
extreme levels of exertion, depending on the action, movement or
manipulation involved. The authors have undertaken several studies
looking at grip choice and comfort. It is hoped that in providing
improved understanding of discomfort during ADLs this will aid in
the design of consumer products.
Previous work by the authors outlined a methodology for
calculating pain frequency and pain level for a range of tasks. From
an online survey undertaken by the authors with regards
manipulating objects during everyday tasks, tasks involving
gripping were seen to produce the highest levels of pain and
discomfort. Questioning of the participants showed that cleaning
tasks were seen to be ADL's that produced the highest levels of
discomfort, with women feeling higher levels of discomfort than
men.
This paper looks at the methodology for calculating pain
frequency and pain level with particular regards to gripping
activities. This methodology shows that activities such as mopping,
sweeping and hoovering shows the highest numbers of pain
frequency and pain level at 3112.5 frequency per month while the
pain level per person doing this action was 0.78.The study then uses
thin-film force sensors to analyze the force distribution in the hand
whilst hoovering and compares this for differing grip styles and
genders. Women were seen to have more of their hand under a
higher pressure than men when undertaking hoovering. This
suggests that women may feel greater discomfort than men since
their hand is at a higher pressure more of the time.
Abstract: The Muslim faith requires individuals to fast between
the hours of sunrise and sunset during the month of Ramadan. Our
recent work has concentrated on some of the changes that take place
during the daytime when fasting. A questionnaire was developed to
assess subjective estimates of physical, mental and social activities,
and fatigue. Four days were studied: in the weeks before and after
Ramadan (control days) and during the first and last weeks of
Ramadan (experimental days). On each of these four days, this
questionnaire was given several times during the daytime and once
after the fast had been broken and just before individuals retired at
night.
During Ramadan, daytime mental, physical and social activities
all decreased below control values but then increased to abovecontrol
values in the evening. The desires to perform physical and
mental activities showed very similar patterns. That is, individuals
tried to conserve energy during the daytime in preparation for the
evenings when they ate and drank, often with friends. During
Ramadan also, individuals were more fatigued in the daytime and
napped more often than on control days. This extra fatigue probably
reflected decreased sleep, individuals often having risen earlier
(before sunrise, to prepare for fasting) and retired later (to enable
recovery from the fast).
Some physiological measures and objective measures of
performance (including the response to a bout of exercise) have also
been investigated. Urine osmolality fell during the daytime on
control days as subjects drank, but rose in Ramadan to reach values
at sunset indicative of dehydration. Exercise performance was also
compromised, particularly late in the afternoon when the fast had
lasted several hours. Self-chosen exercise work-rates fell and a set
amount of exercise felt more arduous. There were also changes in
heart rate and lactate accumulation in the blood, indicative of greater
cardiovascular and metabolic stress caused by the exercise in
subjects who had been fasting. Daytime fasting in Ramadan produces
widespread effects which probably reflect combined effects of sleep
loss and restrictions to intakes of water and food.
Abstract: Reciprocating compressors are flexible to handle wide capacity and condition swings, offer a very efficient method of compressing almost any gas mixture in wide range of pressure, can generate high head independent of density, and have numerous applications and wide power ratings. These make them vital component in various units of industrial plants. In this paper optimum reciprocating compressor configuration regarding interstage pressures, low suction pressure, non-lubricated cylinder, speed of machine, capacity control system, compressor valve, lubrication system, piston rod coating, cylinder liner material, barring device, pressure drops, rod load, pin reversal, discharge temperature, cylinder coolant system, performance, flow, coupling, special tools, condition monitoring (including vibration, thermal and rod drop monitoring), commercial points, delivery and acoustic conditions are presented.
Abstract: This study aims to propose three evaluation methods to
evaluate the Tokyo Cap and Trade Program when emissions trading is
performed virtually among enterprises, focusing on carbon dioxide
(CO2), which is the only emitted greenhouse gas that tends to increase.
The first method clarifies the optimum reduction rate for the highest
cost benefit, the second discusses emissions trading among enterprises
through market trading, and the third verifies long-term emissions
trading during the term of the plan (2010-2019), checking the validity
of emissions trading partly using Geographic Information Systems
(GIS). The findings of this study can be summarized in the following
three points.
1. Since the total cost benefit is the greatest at a 44% reduction rate, it
is possible to set it more highly than that of the Tokyo Cap and
Trade Program to get more total cost benefit.
2. At a 44% reduction rate, among 320 enterprises, 8 purchasing
enterprises and 245 sales enterprises gain profits from emissions
trading, and 67 enterprises perform voluntary reduction without
conducting emissions trading. Therefore, to further promote
emissions trading, it is necessary to increase the sales volumes of
emissions trading in addition to sales enterprises by increasing the
number of purchasing enterprises.
3. Compared to short-term emissions trading, there are few enterprises
which benefit in each year through the long-term emissions trading
of the Tokyo Cap and Trade Program. Only 81 enterprises at the
most can gain profits from emissions trading in FY 2019. Therefore,
by setting the reduction rate more highly, it is necessary to increase
the number of enterprises that participate in emissions trading and
benefit from the restraint of CO2 emissions.