Abstract: High strength concrete has been used in situations
where it may be exposed to elevated temperatures. Numerous authors
have shown the significant contribution of polypropylene fiber to the
spalling resistance of high strength concrete.
When cement-based composite that reinforced by polypropylene
fibers heated up to 170 °C, polypropylene fibers readily melt and
volatilize, creating additional porosity and small channels in to the
matrix that cause the poor structure and low strength.
This investigation develops on the mechanical properties of mortar
incorporating polypropylene fibers exposed to high temperature.
Also effects of different pozzolans on strength behaviour of samples
at elevated temperature have been studied.
To reach this purpose, the specimens were produced by partial
replacement of cement with finely ground glass, silica fume and rice
husk ash as high reactive pozzolans. The amount of this replacement
was 10% by weight of cement to find the effects of pozzolans as a
partial replacement of cement on the mechanical properties of
mortars. In this way, lots of mixtures with 0%, 0.5%, 1% and 1.5% of
polypropylene fibers were cast and tested for compressive and
flexural strength, accordance to ASTM standard. After that
specimens being heated to temperatures of 300, 600 °C, respectively,
the mechanical properties of heated samples were tested.
Mechanical tests showed significant reduction in compressive
strength which could be due to polypropylene fiber melting. Also
pozzolans improve the mechanical properties of sampels.
Abstract: Use of fly ash as a supplementary cementing material
in large volumes can bring both technological and economic benefits
for concrete industry. In this investigation mix proportions for high
volume fly ash concrete were determined at cement replacement
levels of 50%, 55%, 60% and 65% with low calcium fly ash. Flexural
and compressive strengths of different mixes were measured at ages
of 7, 28 and 90 days. Flexural strength of composite section prepared
from pavement quality and lean high volume fly ash concrete was
determined at the age of 28 days. High volume fly ash concrete mixes
exhibited higher rate of strength gain and age factors than
corresponding reference concrete mixes. The optimum cement
replacement level for pavement quality concrete was found to be
60%. The consideration of bond between pavement quality and lean
of high volume fly ash concrete will be beneficial in design of rigid
pavements.
Abstract: An on-line condition monitoring method for transmission line is proposed using electrical circuit theory and IT technology in this paper. It is reasonable that the circuit parameters such as resistance (R), inductance (L), conductance (g) and capacitance (C) of a transmission line expose the electrical conditions and physical state of the line. Those parameters can be calculated from the linear equation composed of voltages and currents measured by synchro-phasor measurement technique at both end of the line. A set of linear voltage drop equations containing four terminal constants (A, B ,C ,D ) are mathematical models of the transmission line circuits. At least two sets of those linear equations are established from different operation condition of the line, they may mathematically yield those circuit parameters of the line. The conditions of line connectivity including state of connecting parts or contacting parts of the switching device may be monitored by resistance variations during operation. The insulation conditions of the line can be monitored by conductance (g) and capacitance(C) measurements. Together with other condition monitoring devices such as partial discharge, sensors and visual sensing device etc.,they may give useful information to monitor out any incipient symptoms of faults. The prototype of hardware system has been developed and tested through laboratory level simulated transmission lines. The test has shown enough evident to put the proposed method to practical uses.
Abstract: Nowadays predicting political risk level of country
has become a critical issue for investors who intend to achieve
accurate information concerning stability of the business
environments. Since, most of the times investors are layman and
nonprofessional IT personnel; this paper aims to propose a
framework named GECR in order to help nonexpert persons to
discover political risk stability across time based on the political
news and events.
To achieve this goal, the Bayesian Networks approach was
utilized for 186 political news of Pakistan as sample dataset.
Bayesian Networks as an artificial intelligence approach has been
employed in presented framework, since this is a powerful technique
that can be applied to model uncertain domains. The results showed
that our framework along with Bayesian Networks as decision
support tool, predicted the political risk level with a high degree of
accuracy.
Abstract: Electronic commerce is growing rapidly with on-line
sales already heading for hundreds of billion dollars per year. Due to
the huge amount of money transferred everyday, an increased
security level is required. In this work we present the architecture of
an intelligent speaker verification system, which is able to accurately
verify the registered users of an e-commerce service using only their
voices as an input. According to the proposed architecture, a
transaction-based e-commerce application should be complemented
by a biometric server where customer-s unique set of speech models
(voiceprint) is stored. The verification procedure requests from the
user to pronounce a personalized sequence of digits and after
capturing speech and extracting voice features at the client side are
sent back to the biometric server. The biometric server uses pattern
recognition to decide whether the received features match the stored
voiceprint of the customer who claims to be, and accordingly grants
verification. The proposed architecture can provide e-commerce
applications with a higher degree of certainty regarding the identity
of a customer, and prevent impostors to execute fraudulent
transactions.
Abstract: Changing technology and increased constituent
demand for government services derive the need for governmental
responsiveness. The government organisations in the developing
countries will be under increased pressure to change their
bureaucratic systems to be able to respond rapidly to changing and
increasing requirements and rapid technology advancements. This
paper aims to present a conceptual framework for explaining the
main barriers and drivers of public e-service development. Therefore,
the framework provides a basic context within which the process and
practice of E-Service can be implemented successfully in the public
sector organisations. The framework is flexible enough to be adopted
by governments at different levels; national or local by developing
countries around the world.
Abstract: While in practice negotiation is always a mix of
cooperation and competition, these two elements correspond to
different approaches of the relationship and also different orientations
in term of strategy, techniques, tactics and arguments employed by
the negotiators with related effects and in the end leading to different
outcomes. The levels of honesty, trust and therefore cooperation are
influenced not only by the uncertainty of the situation, the objectives,
stakes or power but also by the orientation given from the very
beginning of the relationship. When negotiation is reduced to a
confrontation of power, participants rely on coercive measures, using
different kinds of threats or make false promises and bluff in order to
establish a more acceptable balance of power.
Most of the negotiators have a tendency to complain about the
unethical aspects of the tactics used by their counterparts while, as
the same time, they are mostly unaware of the sources of influence of
their own vision and practices. In this article, our intention is to
clarify these sources and try to understand what can lead negotiators
to unethical practices.
Abstract: The effectiveness of consuming a nutrient fortified oat drink on iron, zinc, vitamin A and vitamin C status was assessed among a cohort of school-aged Filipino children. Ultimate study implementation permitted only a within-subject comparison of change in nutritional status after four months of consuming a nutrient fortified oat drink. Thirty-eight anemic children (5-8 years) consumed an oat drink fortified with iron as NaFeEDTA, zinc, vitamin A and vitamin C for 120 days. Height, weight, serum nutrient levels, anemia status and dietary intake were assessed pre and post intervention. Thirty-four anemic children completed the intervention. After 4 months of intervention, prevalence of anemia decreased by 68% and significant improvements in iron and vitamin A status were observed. Results demonstrate the effectiveness of the fortified oat drink in alleviating anemia in young children and highlight the value of fortification programs
Abstract: Because of its global reach, reduction of time
restraints, and ability to reduce costs and increase sales, use of the
Internet, the World Wide Web (WWW), and related technologies
can be a competitive tool in the arsenal of small and medium-sized
enterprises (SMEs). Countries the world over are interested in the
successful adoption of the Internet by SMEs. Because a vast
majority of jobs come from that sector, greater financial success of
SMEs translates into greater job growth and, subsequently, higher
tax revenue to the government. This research investigated the level
of Internet usage for business solutions by small and medium
enterprises in Jordan. Through the survey of a random sample of
100 firms with less than 500 employees and from data obtained
from this survey that formed the basis for our study, we found that
a majority of respondents use the Internet in business activities ,
the adoption of the Internet as a business tool is limited to a
brochure where Web site which primarily provides one way. As
such, there wasn't interactive information about the company and
its products and services.
Abstract: In a competitive energy market, system reliability
should be maintained at all times. Power system operation being of
online in nature, the energy balance requirements must be satisfied to
ensure reliable operation the system. To achieve this, information
regarding the expected status of the system, the scheduled
transactions and the relevant inputs necessary to make either a
transaction contract or a transmission contract operational, have to be
made available in real time. The real time procedure proposed,
facilitates this. This paper proposes a quadratic curve learning
procedure, which enables a generator-s contribution to the retailer
demand, power loss of transaction in a line at the retail end and its
associated losses for an oncoming operating scenario to be predicted.
Matlab program was used to test in on a 24-bus IEE Reliability Test
System, and the results are found to be acceptable.
Abstract: Analytical investigation of the sedimentation
processes in the river engineering and hydraulic structures is of vital
importance as this can affect water supply for the cultivating lands in
the command area. The reason being that gradual sediment formation
behind the reservoir can reduce the nominal capacity of these dams.
The aim of the present paper is to analytically investigate
sedimentation process along the river course and behind the storage
reservoirs in general and the Eastern Intake of the Dez Diversion weir
in particular using the SHARC software. Results of the model
indicated the water level at 115.97m whereas the real time
measurement from the river cross section was 115.98 m which
suggests a significantly close relation between them. The average
transported sediment load in the river was measured at 0.25mm ,
from which it can be concluded that nearly 100% of the suspended
loads in river are moving which suggests no sediment settling but
indicates that almost all sediment loads enters into the intake. It was
further showed the average sediment diameter entering the intake to
be 0.293 mm which in turn suggests that about 85% of suspended
sediments in the river entre the intake. Comparison of the results
from the SHARC model with those obtained form the SSIIM
software suggests quite similar outputs but distinguishing the
SHARC model as more appropriate for the analysis of simpler
problems than other model.
Abstract: Thrombosis can be life threatening, necessitating therefore its instant treatment. Hydergine, a nootropic agent is used as a cognition enhancer in stroke patients but relatively little is known about its anti-thrombolytic effect. To investigate this aspect, in vivo and ex vivo experiments were designed and conducted. Three groups of rats were injected 1.5mg, 3.0mg and 4.5mg hydergine intraperitonealy with and without prior exposure to fresh plasma. Positive and negative controls were run in parallel. Animals were sacrificed after 1.5hrs and BT, CT, PT, INR, APTT, plasma calcium levels were estimated. For ex vivo analyses, each 1ml blood aspirated was exposed to 0.1mg, 0.2mg, 0.3mg dose of hydergine with parallel controls. Parameters analyzed were as above. Statistical analysis was through one-way ANOVA. Dunken-s and Tukey-s tests provided intra-group variance. BT, CT, PT, INR and APTT increased while calcium levels dropped significantly (P
Abstract: This work presents a numerical model developed to
simulate the dynamics and vibrations of a multistage tractor gearbox.
The effect of time varying mesh stiffness, time varying frictional
torque on the gear teeth, lateral and torsional flexibility of the shafts
and flexibility of the bearings were included in the model. The model
was developed by using the Lagrangian method, and it was applied to
study the effect of three design variables on the vibration and stress
levels on the gears. The first design variable, module, had little effect
on the vibration levels but a higher module resulted to higher bending
stress levels. The second design variable, pressure angle, had little
effect on the vibration levels, but had a strong effect on the stress
levels on the pinion of a high reduction ratio gear pair. A pressure
angle of 25o resulted to lower stress levels for a pinion with 14 teeth
than a pressure angle of 20o. The third design variable, contact ratio,
had a very strong effect on both the vibration levels and bending
stress levels. Increasing the contact ratio to 2.0 reduced both the
vibration levels and bending stress levels significantly. For the gear
train design used in this study, a module of 2.5 and contact ratio of
2.0 for the various meshes was found to yield the best combination
of low vibration levels and low bending stresses. The model can
therefore be used as a tool for obtaining the optimum gear design
parameters for a given multistage spur gear train.
Abstract: In this paper, Fabless Prototyping Methodology is
introduced for the design and analysis of MEMS devices.
Conventionally Finite Element Analysis (FEA) is performed before
system level simulation. In our proposed methodology, system level
simulation is performed earlier than FEA as it is computationally less
extensive and low cost. System level simulations are based on
equivalent behavioral models of MEMS device. Electrostatic
actuation based MEMS Microgripper is chosen as case study to
implement this methodology. This paper addresses the behavioral
model development and simulation of actuator part of an
electrostatically actuated Microgripper. Simulation results show that
the actuator part of Microgripper works efficiently for a voltage range
of 0-45V with the corresponding jaw displacement of 0-4.5425μm.
With some minor changes in design, this range can be enhanced to
15μm at 85V.
Abstract: This study aimed to develop and initially validate an instrument that measures social competency among tertiary level faculty members. A review of extant literature on social competence was done. The review of extant literature led to the writing of the items in the initial instrument which was evaluated by 11 Subject Matter Experts (SMEs). The SMEs were either educators or psychologists. The results of the evaluations done by the SMEs served as bases for the creation of the pre-try-out instrument used in the first trial-run. Insights from the first trial-run participants led to the development of the main try-out instrument used in the final test administration. One Hundred Forty-one participants from five private Higher Education Institutions (HEIs) in the National Capital Region (NCR) and five private HEIs in Central Luzon in the Philippines participated in the final test administration. The reliability of the instrument was evaluated using Cronbach-s Coefficient Alpha formula and had a Cronbach-s Alpha of 0.92. On the other hand, Factor Analysis was used to evaluate the validity of the instrument and six factors were identified. The development of the final instrument was based on the results of the evaluation of the instrument-s reliability and validity. For purposes of recognition, the instrument was named “Social Competency Inventory for Tertiary Level Faculty Members (SCI-TLFM)."
Abstract: To achieve reliable solutions, today-s numerical and
experimental activities need developing more accurate methods and
utilizing expensive facilities, respectfully in microchannels. The analytical
study can be considered as an alternative approach to alleviate
the preceding difficulties. Among the analytical solutions, those with
high robustness and low complexities are certainly more attractive.
The perturbation theory has been used by many researchers to analyze
microflows. In present work, a compressible microflow with constant
heat flux boundary condition is analyzed. The flow is assumed to be
fully developed and steady. The Mach and Reynolds numbers are also
assumed to be very small. For this case, the creeping phenomenon
may have some effect on the velocity profile. To achieve robustness
solution it is assumed that the flow is quasi-isothermal. In this study,
the creeping term which appears in the slip boundary condition
is formulated by different mathematical formulas. The difference
between this work and the previous ones is that the creeping term
is taken into account and presented in non-dimensionalized form.
The results obtained from perturbation theory are presented based
on four non-dimensionalized parameters including the Reynolds,
Mach, Prandtl and Brinkman numbers. The axial velocity, normal
velocity and pressure profiles are obtained. Solutions for velocities
and pressure for two cases with different Br numbers are compared
with each other and the results show that the effect of creeping
phenomenon on the velocity profile becomes more important when
Br number is less than O(ε).
Abstract: Detecting object in video sequence is a challenging
mission for identifying, tracking moving objects. Background
removal considered as a basic step in detected moving objects tasks.
Dual static cameras placed in front and rear moving platform
gathered information which is used to detect objects. Background
change regarding with speed and direction moving platform, so
moving objects distinguished become complicated. In this paper, we
propose framework allows detection moving object with variety of
speed and direction dynamically. Object detection technique built on
two levels the first level apply background removal and edge
detection to generate moving areas. The second level apply Moving
Areas Filter (MAF) then calculate Correlation Score (CS) for
adjusted moving area. Merging moving areas with closer CS and
marked as moving object. Experiment result is prepared on real scene
acquired by dual static cameras without overlap in sense. Results
showing accuracy in detecting objects compared with optical flow
and Mixture Module Gaussian (MMG), Accurate ratio produced to
measure accurate detection moving object.
Abstract: This study discusses the effect of uncertainty on
production levels of a petrochemical complex. Uncertainly or
variations in some model parameters, such as prices, supply and
demand of materials, can affect the optimality or the efficiency of any
chemical process. For any petrochemical complex with many plants,
there are many sources of uncertainty and frequent variations which
require more attention. Many optimization approaches are proposed
in the literature to incorporate uncertainty within the model in order
to obtain a robust solution. In this work, a stability analysis approach
is applied to a deterministic LP model of a petrochemical complex
consists of ten plants to investigate the effect of such variations on
the obtained optimal production levels. The proposed approach can
determinate the allowable variation ranges of some parameters,
mainly objective or RHS coefficients, before the system lose its
optimality. Parameters with relatively narrow range of variations, i.e.
stability limits, are classified as sensitive parameters or constraints
that need accurate estimate or intensive monitoring. These stability
limits offer easy-to-use information to the decision maker and help in
understanding the interaction between some model parameters and
deciding when the system need to be re-optimize. The study shows
that maximum production of ethylene and the prices of intermediate
products are the most sensitive factors that affect the stability of the
optimum solution
Abstract: This paper discusses a qualitative simulator QRiOM
that uses Qualitative Reasoning (QR) technique, and a process-based
ontology to model, simulate and explain the behaviour of selected
organic reactions. Learning organic reactions requires the application
of domain knowledge at intuitive level, which is difficult to be
programmed using traditional approach. The main objective of
QRiOM is to help learners gain a better understanding of the
fundamental organic reaction concepts, and to improve their
conceptual comprehension on the subject by analyzing the multiple
forms of explanation generated by the software. This paper focuses
on the generation of explanation based on causal theories to explicate
various phenomena in the chemistry subject. QRiOM has been tested
with three classes problems related to organic chemistry, with
encouraging results. This paper also presents the results of
preliminary evaluation of QRiOM that reveal its explanation
capability and usefulness.
Abstract: Implementing Information Technology/ Information
System (IT/IS) is critical for every industry as its potential benefits
have been to motivate many industries including the Malaysian
construction industry to invest in it. To successfully implement IT/IS
has become the major concern for every organisation. Identifying the
critical success factors (CSFs) has become the main agenda for
researchers, academicians and practitioners due to the wide number
of failures reported. This research paper seeks to identify the CSFs
that influence the successful implementation of IT/IS in construction
industry in Malaysia. Limited factors relating to people issue will be
highlighted here to showcase some as it becomes one of the major
contributing factors to the failure. Three (3) organisations have
participated in this study. Semi-structured interviews are employed as
they offer sufficient flexibility to ensure that all relevant factors are
covered. Several key issues contributing to successful
implementations of IT/IS are identified. The results of this study
reveal that top management support, communication, user
involvement, IT staff roles and responsibility, training/skills, leader/
IT Leader, organisation culture, knowledge/ experience, motivation,
awareness, focus and ambition, satisfaction, teamwork/ collaboration,
willingness to change, attitude, commitment, management style,
interest in IT, employee behaviour towards collaborative
environment, trust, interpersonal relationship, personal characteristic
and competencies are significantly associated with the successful
implementations of IT/IS. It is anticipated that this study will create
awareness and contribute to a better understanding amongst
construction industry players and will assist them to successfully
implement IT/IS.