Abstract: In this paper, the effect of the moving platform size on the workspace volume of 6–6 cable-suspended parallel robots is investigated in details for different geometric configurations and orientations of the moving platform. The obtained hints can be used as a rule of thumb in designing this type of robot.
Abstract: Electro-optical (EO) stabilized platforms have been widely used for surveillance and reconnaissance on various types of vehicles, from surface ships to unmanned air vehicles (UAVs). EO stabilized platforms usually consist of an assembly of structure, bearings, and motors called gimbals in which a gyroscope is installed. EO elements such as a CCD camera and IR camera, are mounted to a gimbal, which has a range of motion in elevation and azimuth and can designate and track a target. In addition, a laser range finder (LRF) can be added to the gimbal in order to acquire the precise slant range from the platform to the target. Recently, a versatile functionality of target localization is needed in order to cooperate with the weapon systems that are mounted on the same platform. The target information, such as its location or velocity, needed to be more accurate. The accuracy of the target information depends on diverse component errors and alignment errors of each component. Specially, the type of moving platform can affect the accuracy of the target information. In the case of flying platforms, or UAVs, the target location error can be increased with altitude so it is important to measure altitude as precisely as possible. In the case of surface ships, target location error can be increased with obliqueness of the elevation angle of the gimbal since the altitude of the EO stabilized platform is supposed to be relatively low. The farther the slant ranges from the surface ship to the target, the more extreme the obliqueness of the elevation angle. This can hamper the precise acquisition of the target information. So far, there have been many studies on EO stabilized platforms of flying vehicles. However, few researchers have focused on ship-borne EO stabilized platforms of the surface ship. In this paper, we deal with a target localization method when an EO stabilized platform is located on the mast of a surface ship. Especially, we need to overcome the limitation caused by the obliqueness of the elevation angle of the gimbal. We introduce a well-known approach for target localization using Unscented Kalman Filter (UKF) and present the problem definition showing the above-mentioned limitation. Finally, we want to show the effectiveness of the approach that will be demonstrated through computer simulations.
Abstract: Industrial robots play a vital role in automation
however only little effort are taken for the application of robots in
machining work such as Grinding, Cutting, Milling, Drilling,
Polishing etc. Robot parallel manipulators have high stiffness,
rigidity and accuracy, which cannot be provided by conventional
serial robot manipulators. The aim of this paper is to perform the
modeling and the workspace analysis of a 3 DOF Parallel
Manipulator (3 DOF PM). The 3 DOF PM was modeled and
simulated using 'ADAMS'. The concept involved is based on the
transformation of motion from a screw joint to a spherical joint
through a connecting link. This paper work has been planned to
model the Parallel Manipulator (PM) using screw joints for very
accurate positioning. A workspace analysis has been done for the
determination of work volume of the 3 DOF PM. The position of the
spherical joints connected to the moving platform and the
circumferential points of the moving platform were considered for
finding the workspace. After the simulation, the position of the joints
of the moving platform was noted with respect to simulation time and
these points were given as input to the 'MATLAB' for getting the
work envelope. Then 'AUTOCAD' is used for determining the work
volume. The obtained values were compared with analytical
approach by using Pappus-Guldinus Theorem. The analysis had been
dealt by considering the parameters, link length and radius of the
moving platform. From the results it is found that the radius of
moving platform is directly proportional to the work volume for a
constant link length and the link length is also directly proportional
to the work volume, at a constant radius of the moving platform.
Abstract: This article proposes modeling, simulation and
kinematic and workspace analysis of a spatial cable suspended robot
as incompletely Restrained Positioning Mechanism (IRPM). These
types of robots have six cables equal to the number of degrees of
freedom. After modeling, the kinds of workspace are defined then an
statically reachable combined workspace for different geometric
structures of fixed and moving platform is obtained. This workspace
is defined as the situations of reference point of the moving platform
(center of mass) which under external forces such as weight and with
ignorance of inertial effects, the moving platform should be in static
equilibrium under conditions that length of all cables must not be
exceeded from the maximum value and all of cables must be at
tension (they must have non-negative tension forces). Then the effect
of various parameters such as the size of moving platform, the size of
fixed platform, geometric configuration of robots, magnitude of
applied forces and moments to moving platform on workspace of
these robots with different geometric configuration are investigated.
Obtained results should be effective in employing these robots under
different conditions of applied wrench for increasing the workspace
volume.
Abstract: A Cable-Driven Locomotion Interface provides a low
inertia haptic interface and is used as a way of enabling the user
to walk and interact with virtual surfaces. These surfaces generate
Cartesian wrenches which must be optimized for each motorized
reel in order to reproduce a haptic sensation in both feet. However,
the use of wrench control requires a measure of the cable tensions
applied to the moving platform. The latter measure may be inaccurate
if it is based on sensors located near the reel. Moreover, friction
hysteresis from the reel moving parts needs to be compensated
for with an evaluation of low angular velocity of the motor shaft.
Also, the pose of the platform is not known precisely due to cable
sagging and mechanical deformation. This paper presents a non-ideal
motorized reel design with its corresponding control strategy that
aims at overcoming the aforementioned issues. A transfert function
of the reel based on frequency responses in function of cable tension
and cable length is presented with an optimal adaptative PIDF
controller. Finally, an hybrid position/tension control is discussed with
an analysis of the stability for achieving a complete functionnality of
the haptic platform.
Abstract: Detecting object in video sequence is a challenging
mission for identifying, tracking moving objects. Background
removal considered as a basic step in detected moving objects tasks.
Dual static cameras placed in front and rear moving platform
gathered information which is used to detect objects. Background
change regarding with speed and direction moving platform, so
moving objects distinguished become complicated. In this paper, we
propose framework allows detection moving object with variety of
speed and direction dynamically. Object detection technique built on
two levels the first level apply background removal and edge
detection to generate moving areas. The second level apply Moving
Areas Filter (MAF) then calculate Correlation Score (CS) for
adjusted moving area. Merging moving areas with closer CS and
marked as moving object. Experiment result is prepared on real scene
acquired by dual static cameras without overlap in sense. Results
showing accuracy in detecting objects compared with optical flow
and Mixture Module Gaussian (MMG), Accurate ratio produced to
measure accurate detection moving object.