Abstract: In this paper, two options of anodic alumina barrier
layer thinning have been demonstrated. The approaches varied with
the duration of the voltage step. It was found that too long step of the
barrier layer thinning process leads to chemical etching of the
nanopores on their top. At the bottoms pores are not fully opened
what is disadvantageous for further applications in nanofabrication.
On the other hand, while the duration of the voltage step is controlled
by the current density (value of the current density cannot exceed
75% of the value recorded during previous voltage step) the pores are
fully opened. However, pores at the bottom obtained with this
procedure have smaller diameter, nevertheless this procedure
provides electric contact between the bare aluminum (substrate) and
electrolyte, what is suitable for template assisted electrodeposition,
one of the most cost-efficient synthesis method in nanotechnology.
Abstract: This paper presents an adaptive thermal comfort
model study in the tropical country of Malaysia. A number of
researchers have been interested in applying the adaptive thermal
comfort model to different climates throughout the world, but so far
no study has been performed in Malaysia. For the use as a thermal
comfort model, which better applies to hot and humid climates, the
adaptive thermal comfort model was developed as part of this
research by using the collected results from a large field study in six
lecture halls with 178 students. The relationship between the
operative temperature and behavioral adaptations was determined. In
the developed adaptive model, the acceptable indoor neutral
temperatures lay within the range of 23.9-26.0C, with outdoor
temperatures ranging between 27.0-34.6C. The most comfortable
temperature for students in lecture hall was 25.7C.
Abstract: The belief of a heavenly God is enshrined to all
Abrahamic religions which form the three major religions of the
world today. Muslims believe in Allah who is above the seven
heavens. The youth in the United Arab Emirates (UAE) study Islamic
courses as part of their high school curriculum and are required to
take at least one Islamic course at the university level to gain credit
hours towards their general education (GENED). This paper provides
an insight of what the youth studying in the UAE think of where
Allah is. Our analysis shows that a big number of Muslim youth were
not sure, especially those from the Middle Eastern and Arab countries
bringing to conclusion that this subject needs to be revisited again in
the course work.
Abstract: Interaction between human, location and activity
defines space. In the framework of these relations, space is a
container for current specifications in relations of the 3 mentioned
elements. The change of land utility considered with average
performance range, urban regulations, society requirements etc. will
provide welfare and comfort for citizens. From an engineering view it
is fundamental that choosing a proper location for a specific civil
activity requires evaluation of locations from different perspectives.
The debate of desirable establishment of municipal service elements
in urban regions is one of the most important issues related to urban
planning. In this paper, the research type is applicable based on goal,
and is descriptive and analytical based on nature. Initially existing
terminals in Esfahan are surveyed and then new locations are
presented based on evaluated criteria. In order to evaluate terminals
based on the considered factors, an AHP model is used at first to
estimate weight of different factors and then existing and suggested
locations are evaluated using Arc GIS software and AHP model
results. The results show that existing bus terminals are located in
fairly proper locations. Further results of this study suggest new
locations to establish terminals based on urban criteria.
Abstract: Fiber Bragg optic sensor is embedded in composite
material to detect and monitor the damage that occurs in composite
structures. In this paper, we deal with the mode-Ι delamination to
determine the material strength to crack propagation, using the
coupling mode theory and T-matrix method to simulate the FBGs
spectrum for both uniform and non-uniform strain distribution. The
double cantilever beam test is modeled in FEM to determine the
longitudinal strain. Two models are implemented, the first is the
global half model, and the second is the sub-model to represent the
FBGs with higher refined mesh. This method can simulate damage in
composite structures and converting strain to a wavelength shifting in
the FBG spectrum.
Abstract: The present study was undertaken to investigate the
effect of aging parameters (time and temperature) on the mechanical
properties of Be-and/or Zr- treated Al-Mg-Zn (7075) alloys. Ultimate
tensile strength, 0.5% offset yield strength and % elongation
measurements were carried out on specimens prepared from cast and
heat treated 7075 alloys containing Be and/or Zr. Different aging
treatment were carried out for the as solution treated (SHT)
specimens (after quenching in warm water). The specimens were
aged at different conditions; Natural and artificial aging was carried
out at room temperature, 120C, 150C, 180C and 220C for different
periods of time. Duplex aging was performed for SHT conditions
(pre-aged at different time and temperature followed by high
temperature aging). Ultimate tensile strength, yield strength and %
elongation data results as a function of different aging parameters are
analysed. A statistical design of experiments (DOE) approach using
fractional factorial design is applied to acquire an understanding of
the effects of these variables and their interactions on the mechanical
properties of Be- and/or Zr- treated 7075 alloys. Mathematical
models are developed to relate the alloy mechanical properties with
the different aging parameters.
Abstract: Early detection of breast cancer saves many thousands
of lives each year via application of mammography and genetic
screening and many more lives could be saved if nurses are involved
in breast care screening practices. So, the aim of the study was to
identify nurse's role in early detection of breast cancer through
mammography and genetic screening and its impact on patient's
outcome. In order to achieve this aim, 400 women above 40 years,
asymptomatic were recruited for mammography and genetic
screening. In addition, 50 nurses and 6 technologists were involved in
the study. A descriptive analytical design was used. Five tools were
utilized: sociodemographic, mammographic examination and risk
factors, women's before, during and after mammography, items
relaying to technologists, and items related to nurses were also
obtained. The study finding revealed that 3% of women detected for
malignancy and 7.25% for fibroadenoma. Statistically significant
differences were found between mammography results and age,
family history, genetic screening, exposure to smoke, and using
contraceptive pills. Nurses have insufficient knowledge about
screening tests. Based on these findings the present study
recommended involvement of nurses in breast care which is very
important to in force population about screening practices.
Abstract: The aim of this study is to develop an anterior lumbar
interbody fusion (ALIF) PEEK cage suitable for Korean people. In this
study, CT images were obtained from Korean male (173cm, 71kg) and
3D Korean lumbar models were reconstructed based on the CT images
to investigate anatomical characteristics. Major design parameters of
anterior lumbar interbody fusion (ALIF) PEEK Cage were selected
using the morphological measurement information of the Korean
Lumbar models. Through finite element analysis and mechanical tests,
the developed ALIFPEEK Cage prototype was compared with the
Fidji Cage (Zimmer. Inc, USA) and it was found that the ALIF
prototype showed similar and/or superior mechanical performance
compared to the FidJi Cage. Also, clinical validation for the ALIF
PEEK Cage prototype was carried out to check predictable troubles in
surgical operations. Finally, it is considered that the convenience and
stability of the prototype was clinically verified.
Abstract: The Standard Penetration Test (SPT) is the most
common in situ test for soil investigations. On the other hand, the
Cone Penetration Test (CPT) is considered one of the best
investigation tools. Due to the fast and accurate results that can be
obtained it complaints the SPT in many applications like field
explorations, design parameters, and quality control assessments.
Many soil index and engineering properties have been correlated to
both of SPT and CPT. Various foundation design methods were
developed based on the outcome of these tests. Therefore it is vital to
correlate these tests to each other so that either one of the tests can be
used in the absence of the other, especially for preliminary evaluation
and design purposes.
The primary purpose of this study was to investigate the
relationships between the SPT and CPT for different type of sandy
soils in Florida. Data for this research were collected from number of
projects sponsored by the Florida Department of Transportation
(FDOT), six sites served as the subject of SPT-CPT correlations. The
correlations were established between the cone resistance (qc), sleeve
friction (fs) and the uncorrected SPT blow counts (N) for various
soils.
A positive linear relationship was found between qc, fs and N for
various sandy soils. In general, qc versus N showed higher
correlation coefficients than fs versus N. qc/N ratios were developed
for different soil types and compared to literature values, the results
of this research revealed higher ratios than literature values.
Abstract: The industrial process adds to engineering wood
products features absent in solid wood, with homogeneous structure
and reduced defects, improved physical and mechanical properties,
bio-deterioration, resistance and better dimensional stability,
improving quality and increasing the reliability of structures wood.
These features combined with using fast-growing trees, make them
environmentally ecological products, ensuring a strong consumer
market. The wood I-joists are manufactured by the industrial profiles
bonding flange and web, an important aspect of the production of
wooden I-beams is the adhesive joint that bonds the web to the
flange. Adhesives can effectively transfer and distribute stresses,
thereby increasing the strength and stiffness of the composite. The
objective of this study is to evaluate different resins in a shear strain
specimens with the aim of analyzing the most efficient resin and
possibility of using national products, reducing the manufacturing
cost. First was conducted a literature review, where established the
geometry and materials generally used, then established and analyzed
8 national resins and produced six specimens for each.
Abstract: Iran has several potential for using renewable
energies, so use them could significantly contribute to energy supply.
The purpose of this paper is to identify the potential of the country
and select the appropriate DG technologies with consideration the
potential and primary energy resources in the regions. In this context,
hybrid energy systems proportionate with the potential of different
regions will be determined based on technical, economic, and
environmental aspect. In the following the proposed structure will be
optimized in terms of size and cost. DG technologies used in this
project include photovoltaic system, wind turbine, diesel generator
and battery bank. The HOMER software is applied for choosing the
appropriate structure and the optimization of system sizing. The
results have been analyzed in terms of technical and economic. The
performance and the cost of each project demonstrate the appropriate
structure of hybrid energy system in that region.
Abstract: The western Tombolo of the Giens peninsula in
southern France, known as Almanarre beach, is subject to coastal
erosion. We are trying to use computer simulation in order to propose
solutions to stop this erosion. Our aim was first to determine the main
factors for this erosion and successfully apply a coupled hydrosedimentological
numerical model based on observations and
measurements that have been performed on the site for decades.
We have gathered all available information and data about waves,
winds, currents, tides, bathymetry, coastal line, and sediments
concerning the site. These have been divided into two sets: one
devoted to calibrating a numerical model using Mike 21 software, the
other to serve as a reference in order to numerically compare the
present situation to what it could be if we implemented different
types of underwater constructions.
This paper presents the first part of the study: selecting and
melting different sources into a coherent data basis, identifying the
main erosion factors, and calibrating the coupled software model
against the selected reference period.
Our results bring calibration of the numerical model with good
fitting coefficients. They also show that the winter South-Western
storm events conjugated to depressive weather conditions constitute a
major factor of erosion, mainly due to wave impact in the northern
part of the Almanarre beach. Together, current and wind impact is
shown negligible.
Abstract: The use of technology in the classroom is an issue that
is constantly evolving. Digital age students learn differently than their
teachers did, so now the teacher should be constantly evolving their
methods and teaching techniques to be more in touch with the
student. In this paper a case study presents how were used some of
these technologies by accompanying a classroom course, this in order
to provide students with a different and innovative experience as their
teacher usually presented the activities to develop. As students
worked in the various activities, they increased their digital skills by
employing unknown tools that helped them in their professional
training. The twenty-first century teacher should consider the use of
Information and Communication Technologies in the classroom
thinking in skills that students of the digital age should possess. It
also takes a brief look at the history of distance education and it is
also highlighted the importance of integrating technology as part of
the student's training.
Abstract: The Great East Japan Earthquake occurred at 14:46 on Friday, March 11, 2011. It was the most powerful known earthquake to have hit Japan. The earthquake triggered extremely destructive tsunami waves of up to 40.5 meters in height. We focus on the ship’s evacuation from tsunami. Then we analyze about ships evacuation from tsunami using multi-agent simulation and we want to prepare for a coming earthquake. We developed a simulation model of ships that set sail from the port in order to evacuate from the tsunami considering the ship carrying dangerous goods.
Abstract: A collection of thirty cultivars/clones of a red pitaya
was used to investigate flowering response to lighting
supplementation in the winter season of 2013-2014 in southern
Taiwan. The night-breaking treatment was conducted during the
period of 10 Oct. 2013 to 5 Mar. 2014 with 4-continuous hours
(22.00 – 02.00 hrs) of additional lighting daily using incandescent
bulbs (100W). Among cultivars and clones tested, twenty-three
genotypes, most belonging to the red-magenta flesh type, were found
to have positively flowering response to the lighting treatment. The
duration of night-breaking treatment for successful flowering
initiation varied from 33- 48 days. The lighting-sensitive genotypes
bore 1-2 flowering flushes. Floral and fruiting stages took 21-26 and
46-59 days, respectively. Among sixteen fruiting genotypes, the
highest fruit set rates were found in Damao 9, D4, D13, Chaozou
large, Chaozhou 5, Small Nick and F22. Five cultivars and clones
(Orejona, D4, Chaozhou large, Chaozhou 5 and Small Nick) produced
fruits with an average weight of more than 300 g per fruit which were
higher than those of the fruits formed in the summer of 2013. Fruits
produced during off-season containing total soluble solids (TSS)
from 17.5 to 20.7oBrix, which were higher than those produced inseason.
Abstract: The aim of this paper is to give an assessment of
environmental effects of IPPC permit conditions of installations that
are in specific territory with high concentration of industrial
activities.
The IPPC permit is the permit that each operator should hold to
operate the installation as stated by the directive 2010/75/UE on
industrial emissions (integrated pollution prevention and control),
known as IED (Industrial Emissions Directive).
The IPPC permit includes all the measures necessary to achieve a
high level of protection of the environment as a whole, also defining
the monitoring requirements as measurement methodology,
frequency and evaluation procedure. The emissions monitoring of a
specific plant may also give indications of the contribution of these
emissions on the air quality of a definite area.
So, it is clear that the IPPC permits are important tools both to
improve the environmental framework and to achieve the air quality
standards, assisting to assess the possible industrial sources
contributions to air pollution.
Abstract: The present paper summarizes the analysis of the
request for consultation of information and data on industrial
emissions made publicly available on the web site of the Ministry of
Environment, Land and Sea on integrated pollution prevention and
control from large industrial installations, the so called “AIA Portal”.
As a matter of fact, a huge amount of information on national
industrial plants is already available on internet, although it is usually
proposed as textual documentation or images.
Thus, it is not possible to access all the relevant information
through interoperability systems and also to retrieval relevant
information for decision making purposes as well as rising of
awareness on environmental issue.
Moreover, since in Italy the number of institutional and private
subjects involved in the management of the public information on
industrial emissions is substantial, the access to the information is
provided on internet web sites according to different criteria; thus, at
present it is not structurally homogeneous and comparable.
To overcome the mentioned difficulties in the case of the
Coordinating Committee for the implementation of the Agreement
for the industrial area in Taranto and Statte, operating before the
IPPC permit granting procedures of the relevant installation located
in the area, a big effort was devoted to elaborate and to validate data
and information on characterization of soil, ground water aquifer and
coastal sea at disposal of different subjects to derive a global
perspective for decision making purposes. Thus, the present paper
also focuses on main outcomes matured during such experience.
Abstract: An analysis is carried out to investigate the effect of
magnetic field and heat source on the steady boundary layer flow and
heat transfer of a Casson nanofluid over a vertical cylinder stretching
exponentially along its radial direction. Using a similarity
transformation, the governing mathematical equations, with the
boundary conditions are reduced to a system of coupled, non –linear
ordinary differential equations. The resulting system is solved
numerically by the fourth order Runge – Kutta scheme with shooting
technique. The influence of various physical parameters such as
Reynolds number, Prandtl number, magnetic field, Brownian motion
parameter, thermophoresis parameter, Lewis number and the natural
convection parameter are presented graphically and discussed for non
– dimensional velocity, temperature and nanoparticle volume
fraction. Numerical data for the skin – friction coefficient, local
Nusselt number and the local Sherwood number have been tabulated
for various parametric conditions. It is found that the local Nusselt
number is a decreasing function of Brownian motion parameter Nb
and the thermophoresis parameter Nt.
Abstract: Collaborative technologies or software known as
groupware are key enabling tools for communication, collaboration
and co-ordination among individuals, work groups and businesses.
Available reviews of the groupware literature are very few,
and mostly neither systematic nor recent.
This paper is an effort to fill this gap, and to provide researchers,
with a more up-to-date and wide systematic literature review. For this
purpose, 1087 scholarly articles, published from 1990 to 2013, on the
topic of groupware, were collected by the literature search. The study
here adopted the systematic approach of lexical analysis for the
analysis of those articles.
Abstract: Verification and Validation of Simulated Process
Model is the most important phase of the simulator life cycle.
Evaluation of simulated process models based on Verification and
Validation techniques checks the closeness of each component model
(in a simulated network) with the real system/process with respect to
dynamic behaviour under steady state and transient conditions. The
process of Verification and Validation helps in qualifying the process
simulator for the intended purpose whether it is for providing
comprehensive training or design verification. In general, model
verification is carried out by comparison of simulated component
characteristics with the original requirement to ensure that each step
in the model development process completely incorporates all the
design requirements. Validation testing is performed by comparing
the simulated process parameters to the actual plant process
parameters either in standalone mode or integrated mode.
A Full Scope Replica Operator Training Simulator for PFBR -
Prototype Fast Breeder Reactor has been developed at IGCAR,
Kalpakkam, INDIA named KALBR-SIM (Kalpakkam Breeder
Reactor Simulator) where in the main participants are
engineers/experts belonging to Modeling Team, Process Design and
Instrumentation & Control design team. This paper discusses about
the Verification and Validation process in general, the evaluation
procedure adopted for PFBR operator training Simulator, the
methodology followed for verifying the models, the reference
documents and standards used etc. It details out the importance of
internal validation by design experts, subsequent validation by
external agency consisting of experts from various fields, model
improvement by tuning based on expert’s comments, final
qualification of the simulator for the intended purpose and the
difficulties faced while co-coordinating various activities.