Abstract: A new hybrid method to realise high-precision
distortion determination for optical ultra-precision 3D measurement
systems based on stereo cameras using active light projection is
introduced. It consists of two phases: the basic distortion
determination and the refinement. The refinement phase of the
procedure uses a plane surface and projected fringe patterns as
calibration tools to determine simultaneously the distortion of both
cameras within an iterative procedure. The new technique may be
performed in the state of the device “ready for measurement" which
avoids errors by a later adjustment. A considerable reduction of
distortion errors is achieved and leads to considerable improvements
of the accuracy of 3D measurements, especially in the precise
measurement of smooth surfaces.
Abstract: Since the presentation of the backpropagation algorithm, a vast variety of improvements of the technique for training a feed forward neural networks have been proposed. This article focuses on two classes of acceleration techniques, one is known as Local Adaptive Techniques that are based on weightspecific only, such as the temporal behavior of the partial derivative of the current weight. The other, known as Dynamic Adaptation Methods, which dynamically adapts the momentum factors, α, and learning rate, η, with respect to the iteration number or gradient. Some of most popular learning algorithms are described. These techniques have been implemented and tested on several problems and measured in terms of gradient and error function evaluation, and percentage of success. Numerical evidence shows that these techniques improve the convergence of the Backpropagation algorithm.
Abstract: A simple analytical model has been developed to
optimize biasing conditions for obtaining maximum linearity among
lattice-matched, pseudomorphic and metamorphic HEMT types as
well as enhancement and depletion HEMT modes. A nonlinear
current-voltage model has been simulated based on extracted data to
study and select the most appropriate type and mode of HEMT in
terms of a given gate-source biasing voltage within the device so as
to employ the circuit for the highest possible output current or
voltage linear swing. Simulation results can be used as a basis for the
selection of optimum gate-source biasing voltage for a given type
and mode of HEMT with regard to a circuit design. The
consequences can also be a criterion for choosing the optimum type
or mode of HEMT for a predetermined biasing condition.
Abstract: The increasing recognition of the need for education to be closely aligned with team playing, project based learning and problem solving approaches has increase the interest in collaborative learning among university and college instructors. Using online collaboration learning in learning can enhance the outcome and achievement of students as well as improve their communication, critical thinking and personnel skills. The current research aims at examining the effect of OCL on the student's achievement at Kingdom of Bahrain. Numbers of objectives were set to achieve the aim of the research include: investigating the current situation regarding the collaborative learning and OCL at the Kingdom of Bahrain by identifying the advantages and effectiveness of OCL as a learning tool over traditional learning, examining the factors that affect OCL as well as examining the impact of OCL on the student's achievement. To achieve these objectives, quantitative method was adopted. Two hundred and thirty one questionnaires were distributed to students in different local and private universities at Kingdom of Bahrain. The findings of the research show that most of the students prefer to use FTFCL in learning and that OCL is already adopted in some universities especially in University of Bahrain. Moreover, the most factors affecting the adopted OCL are perceived readiness, and guidance and support.
Abstract: Pyrite (FeS2) is a promising candidate for cathode
materials in batteries because of it`s high theoretical capacity, low
cost and non-toxicity. In this study, nano size iron disulfide thin film
was prepared on graphite substrate through a new method as battery
cathode. In this way, acetylene black and poly vinylidene fluoride
were used as electron conductor and binder, respectively. Fabricated
thin films were analyzed by XRD and SEM. These results and
electrochemical data confirm improvement of battery discharge
capacity in comparison with commercial type of pyrite.
Abstract: This paper presents a method of reducing the feedback
delay time of DWA(Data Weighted Averaging) used in sigma-delta
modulators. The delay time reduction results from the elimination of
the latch at the quantizer output and also from the falling edge
operation. The designed sigma-delta modulator improves the timing
margin about 16%. The sub-circuits of sigma-delta modulator such as
SC(Switched Capacitor) integrator, 9-level quantizer, comparator, and
DWA are designed with the non-ideal characteristics taken into
account. The sigma-delta modulator has a maximum SNR (Signal to
Noise Ratio) of 84 dB or 13 bit resolution.
Abstract: The trend in the world of Information Technology
(IT) is getting increasingly large and difficult projects rather than
smaller and easier. However, the data on large-scale IT project
success rates provide cause for concern. This paper seeks to answer
why large-scale IT projects are different from and more difficult than
other typical engineering projects. Drawing on the industrial
experience, a compilation of the conditions that influence failure is
presented. With a view to improve success rates solutions are
suggested.
Abstract: Precast concrete has been widely adopted in public
housing construction of Hong Kong since the mid-1980s. While
pre-casting is considered an environmental friendly solution, there is
lack of study to investigate the life cycle performance of precast
concrete units. This study aims to bridge the knowledge gap by
providing a comprehensive life cycle assessment (LCA) study for two
precast elements namely façade and bathroom. The results show that
raw material is the most significant contributor of environmental
impact accounting for about 90% to the total impact. Furthermore,
human health is more affected by the production of precast concrete
than the ecosystems.
Abstract: The problem of incompressible steady flow simulation around an airfoil is discussed. For some simplest airfoils (circular, elliptical, Zhukovsky airfoils) the exact solution is known from complex analysis. It allows to compute the intensity of vortex layer which simulates the airfoil. Some modifications of the vortex element method are proposed and test computations are carried out. It-s shown that the these approaches are much more effective in comparison with the classical numerical scheme.
Abstract: Gas turbine systems with wet compression have a
potential for future power generation, since they can offer a high
efficiency and a high specific power with a relatively low cost. In this
study influence of ambient condition on the performance of the wet
compression process is investigated with a non-equilibrium analytical
modeling based on droplet evaporation. Transient behaviors of droplet
diameter and temperature of mixed air are investigated for various
ambient temperatures. Special attention is paid for the effects of
ambient temperature, pressure ratio, and water injection ratios on the
important wet compression variables including compressor outlet
temperature and compression work. Parametric studies show that
downing of the ambient temperature leads to lower compressor outlet
temperature and consequently lower consumption of compression
work even in wet compression processes.
Abstract: The objective of this paper is the introduction to a
unified optimization framework for research and education. The
OPTILIB framework implements different general purpose algorithms
for combinatorial optimization and minimum search on standard continuous
test functions. The preferences of this library are the straightforward
integration of new optimization algorithms and problems
as well as the visualization of the optimization process of different
methods exploring the search space exclusively or for the real time
visualization of different methods in parallel. Further the usage of
several implemented methods is presented on the basis of two use
cases, where the focus is especially on the algorithm visualization.
First it is demonstrated how different methods can be compared
conveniently using OPTILIB on the example of different iterative
improvement schemes for the TRAVELING SALESMAN PROBLEM.
A second study emphasizes how the framework can be used to find
global minima in the continuous domain.
Abstract: The purpose of this paper is to analyze determinants of
information security affecting adoption of the Web-based integrated
information systems (IIS). We introduced Web-based information
systems which are designed to formulate strategic plans for Peruvian
government. Theoretical model is proposed to test impact of
organizational factors (deterrent efforts and severity; preventive
efforts) and individual factors (information security threat; security
awareness) on intentions to proactively use the Web-based IIS .Our
empirical study results highlight that deterrent efforts and deterrent
severity have no significant influence on the proactive use intentions
of IIS, whereas, preventive efforts play an important role in proactive
use intentions of IIS. Thus, we suggest that organizations need to do
preventive efforts by introducing various information security
solutions, and try to improve information security awareness while
reducing the perceived information security threats.
Abstract: This study include the effect of strain and storage
period and their interaction on some quantitative and qualitative traits
and percentages of the egg components in the eggs collected at the
start of production (at age 24 weeks). Eggs were divided into three
storage periods (1, 7 and 14) days under refrigerator temperature (5-
7)0C. Fifty seven eggs obtained randomly from each strain including
Isa Brown and Lohman White. General Linear Model within
SAS programme was used to analyze the collected data
and correlations between the studied traits were calculated for each
strain.Average egg weight (EW), Haugh Unit (HU), yolk index (YI),
yolk % (HP), albumin % (AP) and yolk to albumin ratio (YAR) was
56.629 gm, 87.968 %, 0.493, 22.13%, 67.74% and 32.76
respectively. Egg produced from ISA Brown surpassed those
produced by Lohman White significantly (P
Abstract: This paper is aimed to give an illustration on the
application of Data Envelopment Analysis (DEA) as a tool to assess
Quality Management (QM) efficiency. A variant of DEA, slack based
measure (SBM) is used for this purpose. From this study, it is found
that DEA is suitable to measure QM efficiency and give
improvement suggestions to the inefficient QM.
Abstract: This paper presents the stabilization potential of Class
F pond ash (PA) from a coal fired thermal power station on tropical
peat soil. Peat or highly organic soils are well known for their high
compressibility, natural moisture content, low shear strength and
long-term settlement. This study investigates the effect of different
amount (i.e., 5, 10, 15 and 20%) of PA on peat soil, collected from
Sarawak, Malaysia, mainly compaction and unconfined compressive
strength (UCS) properties. The amounts of PA added to the peat soil
sample as percentage of the dry peat soil mass. With the increase in
PA content, the maximum dry density (MDD) of peat soil increases,
while the optimum moisture content (OMC) decreases. The UCS
value of the peat soils increases significantly with the increase of PA
content and also with curing periods. This improvement on
compressive strength of tropical peat soils indicates that PA has the
potential to be used as a stabilizer for tropical peat soil. Also, the use
of PA in soil stabilization helps in reducing the pond volume and
achieving environment friendly as well as a sustainable development
of natural resources.
Abstract: New advancement of technology and never satisfying demands of the civilization are putting huge pressure on the natural fuel resources and these resources are at a constant threat to its sustainability. To get the best out of the automobile, the optimum balance between performance and fuel economy is important. In the present state of art, either of the above two aspects are taken into mind while designing and development process which puts the other in the loss as increase in fuel economy leads to decrement in performance and vice-versa. In-depth observation of the vehicle dynamics apparently shows that large amount of energy is lost during braking and likewise large amount of fuel is consumed to reclaim the initial state, this leads to lower fuel efficiency to gain the same performance. Current use of Kinetic Energy Recovery System is only limited to sports vehicles only because of the higher cost of this system. They are also temporary in nature as power can be squeezed only during a small time duration and use of superior parts leads to high cost, which results on concentration on performance only and neglecting the fuel economy. In this paper Kinetic Energy Recovery System for storing the power and then using the same while accelerating has been discussed. The major storing element in this system is a Flat Spiral Spring that will store energy by compression and torsion.
The use of spring ensure the permanent storage of energy until used by the driver unlike present mechanical regeneration system in which the energy stored decreases with time and is eventually lost. A combination of internal gears and spur gears will be used in order to make the energy release uniform which will lead to safe usage. The system can be used to improve the fuel efficiency by assisting in overcoming the vehicle’s inertia after braking or to provide instant acceleration whenever required by the driver. The performance characteristics of the system including response time, mechanical efficiency and overall increase in efficiency are demonstrated. This technology makes the KERS (Kinetic Energy Recovery System) more flexible and economical allowing specific application while at the same time increasing the time frame and ease of usage.
Abstract: In this paper, we propose a fuzzy aggregate
production planning (APP) model for blending problem in a brass
factory which is the problem of computing optimal amounts of raw
materials for the total production of several types of brass in a
period. The model has deterministic and imprecise parameters
which follows triangular possibility distributions. The brass casting
APP model can not always be solved by using common approaches
used in the literature. Therefore a mathematical model is presented
for solving this problem. In the proposed model, the Lai and
Hwang-s fuzzy ranking concept is relaxed by using one constraint
instead of three constraints. An application of the brass casting
APP model in a brass factory shows that the proposed model
successfully solves the multi-blend problem in casting process and
determines the optimal raw material purchasing policies.
Abstract: The conjugate gradient optimization algorithm is combined with the modified back propagation algorithm to yield a computationally efficient algorithm for training multilayer perceptron (MLP) networks (CGFR/AG). The computational efficiency is enhanced by adaptively modifying initial search direction as described in the following steps: (1) Modification on standard back propagation algorithm by introducing a gain variation term in the activation function, (2) Calculation of the gradient descent of error with respect to the weights and gains values and (3) the determination of a new search direction by using information calculated in step (2). The performance of the proposed method is demonstrated by comparing accuracy and computation time with the conjugate gradient algorithm used in MATLAB neural network toolbox. The results show that the computational efficiency of the proposed method was better than the standard conjugate gradient algorithm.
Abstract: Software reuse can be considered as the most realistic
and promising way to improve software engineering productivity and
quality. Automated assistance for software reuse involves the
representation, classification, retrieval and adaptation of components.
The representation and retrieval of components are important to
software reuse in Component-Based on Software Development
(CBSD). However, current industrial component models mainly focus
on the implement techniques and ignore the semantic information
about component, so it is difficult to retrieve the components that
satisfy user-s requirements. This paper presents a method of business
component retrieval based on specification matching to solve the
software reuse of enterprise information system. First, a business
component model oriented reuse is proposed. In our model, the
business data type is represented as sign data type based on XML,
which can express the variable business data type that can describe the
variety of business operations. Based on this model, we propose
specification match relationships in two levels: business operation
level and business component level. In business operation level, we
use input business data types, output business data types and the
taxonomy of business operations evaluate the similarity between
business operations. In the business component level, we propose five
specification matches between business components. To retrieval
reusable business components, we propose the measure of similarity
degrees to calculate the similarities between business components.
Finally, a business component retrieval command like SQL is
proposed to help user to retrieve approximate business components
from component repository.
Abstract: Electricity market activities and a growing demand for electricity have led to heavily stressed power systems. This requires operation of the networks closer to their stability limits. Power system operation is affected by stability related problems, leading to unpredictable system behavior. Voltage stability refers to the ability of a power system to sustain appropriate voltage levels through large and small disturbances. Steady-state voltage stability is concerned with limits on the existence of steady-state operating points for the network. FACTS devices can be utilized to increase the transmission capacity, the stability margin and dynamic behavior or serve to ensure improved power quality. Their main capabilities are reactive power compensation, voltage control and power flow control. Among the FACTS controllers, Static Var Compensator (SVC) provides fast acting dynamic reactive compensation for voltage support during contingency events. In this paper, voltage stability assessment with appropriate representations of tap-changer transformers and SVC is investigated. Integrating both of these devices is the main topic of this paper. Effect of the presence of tap-changing transformers on static VAR compensator controller parameters and ratings necessary to stabilize load voltages at certain values are highlighted. The interrelation between transformer off nominal tap ratios and the SVC controller gains and droop slopes and the SVC rating are found. P-V curves are constructed to calculate loadability margins.