Abstract: A mathematical model based on a mass and energy
balance for the combustion in a cement rotary kiln was developed.
The model was used to investigate the impact of replacing about
45 % of the primary coal energy by different alternative fuels.
Refuse derived fuel, waste wood, solid hazardous waste and liquid
hazardous waste were used in the modeling. The results showed that
in order to keep the kiln temperature unchanged, and thereby
maintain the required clinker quality, the production capacity had to
be reduced by 1-15 %, depending on the fuel type. The reason for the
reduction is increased exhaust gas flow rates caused by the fuel
characteristics. The model, which has been successfully validated in a
full-scale experiment, was also used to show that the negative impact
on the production capacity can be avoided if a relatively small part of
the combustion air is replaced by pure oxygen.
Abstract: Waste problem is becoming a future problem all over the world. Magnesium wastes which can be used in recycling processes are produced by many industrial activities. Magnesium borates which have useful properties such as; high heat resistance, corrosion resistance, supermechanical strength, superinsulation, light weight, high coefficient of elasticity and so on. Addition, magnesium borates have great potential in the development of ceramic and detergents industry, whisker-reinforced composites, antiwear, and reducing friction additives.
In this study, using the starting materials of waste magnesium and H3BO3 the hydrothermal method was applied at a moderate temperature of 70oC with different reaction times. Several reaction times of waste magnesium to H3BO3 were selected as; 30, 60, 120, 240 minutes. After the synthesis, X-Ray Diffraction (XRD) and Fourier Transform Infrared Spectroscopy (FT-IR) techniques were applied to products. As a result, the forms of Admontite [MgO(B2O3)3.7(H2O)] and Mcallisterite [Mg2(B6O7(OH)6)2.9(H2O)] were synthesized.
Abstract: Variational methods for optical flow estimation are
known for their excellent performance. The method proposed by Brox
et al. [5] exemplifies the strength of that framework. It combines
several concepts into single energy functional that is then minimized
according to clear numerical procedure. In this paper we propose
a modification of that algorithm starting from the spatiotemporal
gradient constancy assumption. The numerical scheme allows to
establish the connection between our model and the CLG(H) method
introduced in [18]. Experimental evaluation carried out on synthetic
sequences shows the significant superiority of the spatial variant of
the proposed method. The comparison between methods for the realworld
sequence is also enclosed.
Abstract: The main goal of this seminal paper is to introduce the
application of Wireless Sensor Networks (WSN) in long distance
infrastructure monitoring (in particular in pipeline infrastructure
monitoring) – one of the on-going research projects by the Wireless
Communication Research Group at the department of Electronic and
Computer Engineering, Nnamdi Azikiwe University, Awka. The
current sensor network architectures for monitoring long distance
pipeline infrastructures are previewed. These are wired sensor
networks, RF wireless sensor networks, integrated wired and wireless
sensor networks. The reliability of these architectures is discussed.
Three reliability factors are used to compare the architectures in
terms of network connectivity, continuity of power supply for the
network, and the maintainability of the network. The constraints and
challenges of wireless sensor networks for monitoring and protecting
long distance pipeline infrastructure are discussed.
Abstract: This work presents a methodology for the design and
manufacture of propellers oriented to the experimental verification of
theoretical results based on the combined model. The design process
begins by using algorithms in Matlab which output data contain the
coordinates of the points that define the blade airfoils, in this case the
NACA 6512 airfoil was used. The modeling for the propeller blade
was made in NX7, through the imported files in Matlab and with the
help of surfaces. Later, the hub and the clamps were also modeled.
Finally, NX 7 also made possible to create post-processed files to the
required machine. It is possible to find the block of numbers with G
& M codes about the type of driver on the machine. The file
extension is .ptp. These files made possible to manufacture the blade,
and the hub of the propeller.
Abstract: Medicinal plants are most suitable crops for ecological production systems because of their role in human health and the aim of sustainable agriculture to improve ecosystem efficiency and its products quality. Calculations include energy output (contents of energy in seed) and energy inputs (consumption of fertilizers, pesticides, labor, machines, fuel and electricity). The ratio of output of the production to inputs is called the energy outputs / inputs ratio or energy efficiency. One way to quantify essential parts of agricultural development is the energy flow method. The output / input energy ratio is proposed as the most comprehensive single factor in pursuing the objective of sustainability. Sylibum marianum L. is one of the most important medicinal plants in Iran and has effective role on health of growing population in Iran. The objective of this investigation was to find out energy efficiency in conventional and low input production system of Milk thistle. This investigation was carried out in the spring of 2005 – 2007 in the Research Station of Rangelands in Hamand - Damavand region of IRAN. This experiment was done in split-split plot based on randomized complete block design with 3 replications. Treatments were 2 production systems (Conventional and Low input system) in the main plots, 3 planting time (25 of March, 4 and 14 of April) in the sub plots and 2 seed types (Improved and Native of Khoozestan) in the sub-sub plots. Results showed that in conventional production system energy efficiency, because of higher inputs and less seed yield, was less than low input production system. Seed yield was 1199.5 and 1888 kg/ha in conventional and low input systems, respectively. Total energy inputs and out puts for conventional system was 10068544.5 and 7060515.9 kcal. These amounts for low input system were 9533885.6 and 11113191.8 kcal. Results showed that energy efficiency for seed production in conventional and low input system was 0.7 and 1.16, respectively. So, milk thistle seed production in low input system has 39.6 percent higher energy efficiency than conventional production system. Also, higher energy efficiency were found in sooner planting time (25 of March) and native seed of Khoozestan.
Abstract: Scolothrips longicornis Priesner is one of the
important predators of tetranychid mites with a wide distribution
throughout Iran. Life table and population growth parameters of S.
longicornis feeding on two-spotted spider mite, Tetranychus
turkestani Ugarov & Nikolski were investigated under laboratory
condition (26±1ºC, 65±5% R.H. and 16L: 8D). To carry of these
experiments, S. longicornis collections reared on cowpea infested
with T. turkestani were prepared. The eggs with less than 24 hours
old were selected and reared. The emerged larvae feeding directly on
cowpea leaf discs which were infested with T. turkestani. Thirty
females of S. longicornis with 24 hours age were selected and
released on infested leaf discs. They replaced daily to a new leaf disc
and the laying eggs have counted. The experiment continued till the
last thrips had died. The result showed that the mean age mortality of
the adult female thrips were between 21-25 days which is nearly
equal life expectancy (ex) at the time of adult eclosion. Parameters
related to reproductive table including gross reproductive rate, net
reproductive rate, intrinsic rate of natural increase and finite rate of
increase were 48.91, 37.63, 0.26 and 2.3, respectively. Mean age per
female/day, mean fertile egg per female/day, gross hatch rate, mean
net age fertility, mean net age fecundity, net fertility rate and net
fecundity rate were 2.23, 1.76, 0.87, 13.87, 14.26, 69.1 and 78.5,
respectively. Sex ratio of offspring also recorded daily. The highest
sex ratio for females was 0.88 in first day of oviposition. The sex
ratio decreased gradually and reached under 0.46 after the day 26 and
the oviposition rate declined. Then it seems that maintenance of
rearing culture of predatory thrips for mass rearing later than 26 days
after egg-laying commence is not profitable.
Abstract: We have studied the migration of a charged permeable aggregate in electrolyte under the influence of an axial electric field and pressure gradient. The migration of the positively charged aggregate leads to a deformation of the anionic cloud around it. The hydrodynamics of the aggregate is governed by the interaction of electroosmotic flow in and around the particle, hydrodynamic friction and electric force experienced by the aggregate. We have computed the non-linear Nernest-Planck equations coupled with the Dracy- Brinkman extended Navier-Stokes equations and Poisson equation for electric field through a finite volume method. The permeability of the aggregate enable the counterion penetration. The penetration of counterions depends on the volume charge density of the aggregate and ionic concentration of electrolytes at a fixed field strength. The retardation effect due to the double layer polarization increases the drag force compared to an uncharged aggregate. Increase in migration sped from the electrophretic velocity of the aggregate produces further asymmetry in charge cloud and reduces the electric body force exerted on the particle. The permeability of the particle have relatively little influence on the electric body force when Double layer is relatively thin. The impact of the key parameters of electrokinetics on the hydrodynamics of the aggregate is analyzed.
Abstract: S-Curves are commonly used in technology forecasting. They show the paths of product performance in relation to time or investment in R&D. It is a useful tool to describe the inflection points and the limit of improvement of a technology. Companies use this information to base their innovation strategies.
However inadequate use and some limitations of this technique lead
to problems in decision making. In this paper first technology
forecasting and its importance for company level strategies will be
discussed. Secondly the S-Curve and its place among other
forecasting techniques will be introduced. Thirdly its use in
technology forecasting will be discussed based on its advantages,
disadvantages and limitations. Finally an application of S-curve on
3D TV technology using patent data will also be presented and the
results will be discussed.
Abstract: This paper presents the system identification by
physical-s law method and designs the controller for the Azimuth
Angle Control of the Platform of the Multi-Launcher Rocket System
(MLRS) by Root Locus technique. The plant mathematical model
was approximated using MATLAB for simulation and analyze the
system. The controller proposes the implementation of PID
Controller using Programmable Logic Control (PLC) for control the
plant. PID Controllers are widely applicable in industrial sectors and
can be set up easily and operate optimally for enhanced productivity,
improved quality and reduce maintenance requirement. The results
from simulation and experiments show that the proposed a PID
Controller to control the elevation angle that has superior control
performance by the setting time less than 12 sec, the rise time less
than 1.6 sec., and zero steady state. Furthermore, the system has a
high over shoot that will be continue development.
Abstract: Simulation accuracy by recent dynamic vehicle
simulation multidimensional expression significantly has progressed
and acceptable results not only for passive vehicles but also for
active vehicles normally equipped with advanced electronic
components is also provided. Recently, one of the subjects that has it
been considered, is increasing the safety car in design. Therefore,
many efforts have been done to increase vehicle stability especially
in the turn. One of the most important efforts is adjusting the camber
angle in the car suspension system. Optimum control camber angle in
addition to the vehicle stability is effective in the wheel adhesion on
road, reducing rubber abrasion and acceleration and braking. Since
the increase or decrease in the camber angle impacts on the stability
of vehicles, in this paper, a car suspension system mechanism is
introduced that could be adjust camber angle and the mechanism is
application and also inexpensive. In order to reach this purpose, in
this paper, a passive double wishbone suspension system with
variable camber angle is introduced and then variable camber
mechanism designed and analyzed for study the designed system
performance, this mechanism is modeled in Visual Nastran software
and kinematic analysis is revealed.
Abstract: This paper introduces a mixed integer programming model to find the optimum development plan for port Anzali. The model minimizes total system costs taking into account both port infrastructure costs and shipping costs. Due to the multipurpose function of the port, the model consists of 1020 decision variables and 2490 constraints. Results of the model determine the optimum number of berths that should be constructed in each period and for each type of cargo. In addition to, the results of sensitivity analysis on port operation quantity provide useful information for managers to choose the best scenario for port planning with the lowest investment risks. Despite all limitations-due to data availability-the model offers a straightforward decision tools to port planners aspiring to achieve optimum port planning steps.
Abstract: The performance of Advection Upstream Splitting
Method AUSM schemes are evaluated against experimental flow
fields at different Mach numbers and results are compared with
experimental data of subsonic, supersonic and hypersonic flow fields.
The turbulent model used here is SST model by Menter. The
numerical predictions include lift coefficient, drag coefficient and
pitching moment coefficient at different mach numbers and angle of
attacks. This work describes a computational study undertaken to
compute the Aerodynamic characteristics of different air vehicles
configurations using a structured Navier-Stokes computational
technique. The CFD code bases on the idea of upwind scheme for the
convective (convective-moving) fluxes. CFD results for GLC305
airfoil and cone cylinder tail fined missile calculated on above
mentioned turbulence model are compared with the available data.
Wide ranges of Mach number from subsonic to hypersonic speeds are
simulated and results are compared. When the computation is done
by using viscous turbulence model the above mentioned coefficients
have a very good agreement with the experimental values. AUSM
scheme is very efficient in the regions of very high pressure gradients
like shock waves and discontinuities. The AUSM versions simulate
the all types of flows from lower subsonic to hypersonic flow without
oscillations.
Abstract: In the last decade, carbohydrates have attracted great
attention as renewable resources for the chemical industry.
Carbohydrates are abundantly found in nature in the form of
monomers, oligomers and polymers, or as components of
biopolymers and other naturally occurring substances. As natural
products, they play important roles in conferring certain physical,
chemical, and biological properties to their carrier molecules.The
synthesis of this particular carbohydrate glycomonomer is part of our
work to obtain biodegradable polymers. Our current paper describes
the synthesis and characterization of a novel carbohydrate
glycomonomer starting from D-glucose, in several synthesis steps,
that involve the protection/deprotection of the D-glucose ring via
acetylation, tritylation, then selective deprotection of the aromaticaliphatic
protective group, in order to obtain 1,2,3,4-tetra-O-acetyl-
6-O-allyl-β-D-glucopyranose. The glycomonomer was then obtained
by the allylation in drastic conditions of 1,2,3,4-tetra-O-acetyl-6-Oallyl-
β-D-glucopyranose with allylic alcohol in the presence of
stannic chloride, in methylene chloride, at room temperature. The
proposed structure of the glycomonomer, 2,3,4-tri-O-acetyl-1,6-di-
O-allyl-β-D-glucopyranose, was confirmed by FTIR, NMR and
HPLC-MS spectrometry. This glycomonomer will be further
submitted to copolymerization with certain acrylic or methacrylic
monomers in order to obtain competitive plastic materials for
applications in the biomedical field.
Abstract: Multimedia security is an incredibly significant area of concern. The paper aims to discuss a robust image watermarking scheme, which can withstand geometric attacks. The source image is initially moment normalized in order to make it withstand geometric attacks. The moment normalized image is wavelet transformed. The first level wavelet transformed image is segmented into blocks if size 8x8. The product of mean and standard and standard deviation of each block is computed. The second level wavelet transformed image is divided into 8x8 blocks. The product of block mean and the standard deviation are computed. The difference between products in the two levels forms the watermark. The watermark is inserted by modulating the coefficients of the mid frequencies. The modulated image is inverse wavelet transformed and inverse moment normalized to generate the watermarked image. The watermarked image is now ready for transmission. The proposed scheme can be used to validate identification cards and financial instruments. The performance of this scheme has been evaluated using a set of parameters. Experimental results show the effectiveness of this scheme.
Abstract: As German companies roll out their standardized
production systems to offshore manufacturing plants, they face the
challenge of implementing them in different cultural environments.
Studies show that the local adaptation is one of the key factors for a
successful implementation. Thus the question arises of where the line
between standardization and adaptation can be drawn. To answer
this question the influence of culture on production systems is
analysed in this paper. The culturally contingent components of
production systems are identified. Also the contingency factors are
classified according to their impact on the necessary adaptation
changes and implementation effort. Culturally specific decision
making, coordination, communication and motivation patterns
require one-time changes in organizational and process design. The
attitude towards rules requires more intense coaching and controlling.
Lastly a framework is developed to depict standardization and
adaption needs when transplanting production systems into different
cultural environments.
Abstract: It has been proven that early establishment of
microbial flora in digestive tract of ruminants, has a beneficial effect
on their health condition and productivity. A probiotic compound,
made from five bacteria isolated from adult bovine cattle, was dosed
to 15 Holstein newborn calves in order to measure its capacity of
improving body weight gain and reduce diarrhea incidence. The test
was performed in the municipality of Cajicá (Colombia), at 2580
m.a.s.l., throughout rainy season, with environmental temperature
that oscillated between 4 to 25 °C. Five calves were allotted to
control (no addition of probiotic). Treatments 1, and 2 (5 calves per
group) received 10 ml Probiotic mix 1 and 2, respectively. Probiotic
mixes 1 and 2 where similar in microbial composition but different in
production process. Probiotics were added to the morning milk and
dosed on a daily basis by a month and then on a weekly basis for
three additional months. Diarrhea incidence was measured by
observance of number of animals affected in each group; each animal
was weighed up on a daily basis for obtaining weight gain and rumen
fluid samples were extracted with oro-esophageal catheter for
determining level of fiber and grain consumption.
Abstract: Charging and discharging phenomenon on the surface
of materials can be found in plasma display panel, spacecraft
charging, high voltage insulator, etc. This report gives a simple
explanation on this phenomenon. A scanning electron microscope
was used not only as a tool to produce energetic electron beam to
charge an insulator without metallic coating and to produce a surface
discharging (surface breakdown/flashover) but also to observe the
visible charging and discharging on the sample surface. A model of
electric field distribution on the surface was developed in order to
explain charging and discharging phenomena. Since charging and
discharging process involves incubation time, therefore this process
can be used to evaluate the insulation property of materials under
electron bombardment.
Abstract: Since IEC61850 substation communication standard represents the trend to develop new generations of Substation Automation System (SAS), many IED manufacturers pursue this technique and apply for KEMA. In order to put on the market to meet customer demand as fast as possible, manufacturers often apply their products only for basic environment standard certification but claim to conform to IEC61850 certification. Since verification institutes generally perform verification tests only on specific IEDs of the manufacturers, the interoperability between all certified IEDs cannot be guaranteed. Therefore the interoperability between IEDs from different manufacturers needs to be tested. Based upon the above reasons, this study applies the definitions of the information models, communication service, GOOSE functionality and Substation Configuration Language (SCL) of the IEC61850 to build the concept of communication protocols, and build the test environment. The procedures of the test of the data collection and exchange of the P2P communication mode and Client / Server communication mode in IEC61850 are outlined as follows. First, test the IED GOOSE messages communication capability from different manufacturers. Second, collect IED data from each IED with SCADA system and use HMI to display the SCADA platform. Finally, problems generally encountered in the test procedure are summarized.
Abstract: Bubble columns have a variety of applications in
absorption, bio-reactions, catalytic slurry reactions, and coal
liquefaction; because they are simple to operate, provide good heat
and mass transfer, having less operational cost. The use of
Computational Fluid Dynamics (CFD) for bubble column becomes
important, since it can describe the fluid hydrodynamics on both local
and global scale. Euler- Euler two-phase fluid model has been used to
simulate two-phase (air and water) transient up-flow in bubble
column (15cm diameter) using FLUENT6.3. These simulations and
experiments were operated over a range of superficial gas velocities
in the bubbly flow and churn turbulent regime (1 to16 cm/s) at
ambient conditions. Liquid velocity was varied from 0 to 16cm/s. The
turbulence in the liquid phase is described using the standard k-ε
model. The interactions between the two phases are described
through drag coefficient formulations (Schiller Neumann). The
objectives are to validate CFD simulations with experimental data,
and to obtain grid-independent numerical solutions. Quantitatively
good agreements are obtained between experimental data for hold-up
and simulation values. Axial liquid velocity profiles and gas holdup
profiles were also obtained for the simulation.