Abstract: Drought is one of the most serious problems posing a
grave threat to cereals production including maize. Maize
improvement in drought-stress tolerance poses a great challenge as
the global need for food and bio-energy increases. Thus, the current
study was planned to explore the variations and determine the
performance of target traits of maize hybrids at grain growth stage
under drought conditions during 2014 under Adana, Mediterranean
climate conditions, Turkey. Maize hybrids (Sancia, Indaco,
71May69, Aaccel, Calgary, 70May82, 72May80) were evaluated
under (irrigated and water stress). Results revealed that, grain yield
and yield traits had a negative effects because of water stress
conditions compared with the normal irrigation. As well as, based on
the result under normal irrigation, the maximum biological yield and
harvest index were recorded. According to the differences among
hybrids were found that, significant differences were observed among
hybrids with respect to yield and yield traits under current research. Based on the results, grain weight had more effect on grain yield
than grain number during grain filling growth stage under water
stress conditions. In this concern, according to low drought
susceptibility index (less grain yield losses), the hybrid (Indaco) was
more stable in grain number and grain weight. Consequently, it may
be concluded that this hybrid would be recommended for use in the
future breeding programs for production of drought tolerant hybrids.
Abstract: This paper presents the modeling approach in SBO
sequence for VVER 1000 reactors and describes the reactor core
behavior at late in-vessel phase in case of late reflooding by HPIS
and gives preliminary results for the ASTECv2 validation. The work
is focused on investigation of plant behavior during total loss of
power and the operator actions. The main goal of these analyses is to
assess the phenomena arising during the Station blackout (SBO)
followed by primary side high pressure injection system (HPIS)
reflooding of already damaged reactor core at very late “in-vessel”
phase. The purpose of the analyses is to define how the later HPIS
switching on can delay the time of vessel failure or possibly avoid
vessel failure. The times for HPP injection were chosen based on
previously performed investigations.
Abstract: Tamil handwritten document is taken as a key source
of data to identify the writer. Tamil is a classical language which has
247 characters include compound characters, consonants, vowels and
special character. Most characters of Tamil are multifaceted in
nature. Handwriting is a unique feature of an individual. Writer may
change their handwritings according to their frame of mind and this
place a risky challenge in identifying the writer. A new
discriminative model with pooled features of handwriting is proposed
and implemented using support vector machine. It has been reported
on 100% of prediction accuracy by RBF and polynomial kernel based
classification model.
Abstract: One of the most important challenging factors in
medical images is nominated as noise. Image denoising refers to the
improvement of a digital medical image that has been infected by
Additive White Gaussian Noise (AWGN). The digital medical image
or video can be affected by different types of noises. They are
impulse noise, Poisson noise and AWGN. Computed tomography
(CT) images are subjects to low quality due to the noise. Quality of
CT images is dependent on absorbed dose to patients directly in such
a way that increase in absorbed radiation, consequently absorbed
dose to patients (ADP), enhances the CT images quality. In this
manner, noise reduction techniques on purpose of images quality
enhancement exposing no excess radiation to patients is one the
challenging problems for CT images processing. In this work, noise
reduction in CT images was performed using two different
directional 2 dimensional (2D) transformations; i.e., Curvelet and
Contourlet and Discrete Wavelet Transform (DWT) thresholding
methods of BayesShrink and AdaptShrink, compared to each other
and we proposed a new threshold in wavelet domain for not only
noise reduction but also edge retaining, consequently the proposed
method retains the modified coefficients significantly that result good
visual quality. Data evaluations were accomplished by using two
criterions; namely, peak signal to noise ratio (PSNR) and Structure
similarity (Ssim).
Abstract: This paper describes how to dimension the electric
components of a 48V hybrid system considering real customer use.
Furthermore, it provides information about savings in energy and
CO2 emissions by a customer-tailored 48V hybrid. Based on measured customer profiles, the electric units such as the
electric motor and the energy storage are dimensioned. Furthermore,
the CO2 reduction potential in real customer use is determined
compared to conventional vehicles. Finally, investigations are carried
out to specify the topology design and preliminary considerations in
order to hybridize a conventional vehicle with a 48V hybrid system.
The emission model results from an empiric approach also taking into
account the effects of engine dynamics on emissions. We analyzed
transient engine emissions during representative customer driving
profiles and created emission meta models. The investigation showed
a significant difference in emissions when simulating realistic
customer driving profiles using the created verified meta models
compared to static approaches which are commonly used for vehicle
simulation.
Abstract: One of the fundamental characteristics of Information
and Communication Technology (ICT) has been the ever-changing
nature of continuous release and models of ICTs with its impact on
the academic, social, and psychological benefits of its introduction in
schools. However, there seems to be a growing concern about its
negative impact on students when introduced early in schools for
teaching and learning. This study aims to design a model of child
development factors affecting the early introduction of ICTs in
schools in an attempt to improve the understanding of child
development and introduction of ICTs in schools. The proposed
model is based on a sound theoretical framework. It was designed
following a literature review of child development theories and child
development factors. The child development theoretical framework
that fitted to the best of all child development factors was then chosen
as the basis for the proposed model. This study hence found that the
Jean Piaget cognitive developmental theory is the most adequate
theoretical frameworks for modeling child development factors for
ICT introduction in schools.
Abstract: Damaturu is the capital of Yobe State in northeastern
Nigeria where civic amenities and facilities are not adequate even
after 24 years of its existence. The volatile security and political
situations are most significant causes for the same. The basic facility
for the citizens in terms of drinking water and electricity are not
available. For the drinking water, they have to rely on personal
boreholes or the filtered borehole waters available in packaged
sachets in market. The present study is concerned with environmental
impact of indiscriminate disposal of drinking synthetic polythene
water sachets in Damaturu. The sachet water is popularly called as
“pure water”, but its purity is questionable. Increased production and
consumption of sachet water has led to indiscriminate dumping and
disposal of empty sachets leading to serious environmental threat.
The evidence of this is seen for sachets littering the streets and the
drainages blocked by ‘blocks’ of water sachet waste. Sachet water
gained much popularity in Nigeria because the product is convenient
for use, affordable and economically viable. The present study aims
to find out the solution to this environmental problem. The fieldbased
study has found some significant factors that cause
environmental and socio economic effect due to this. Some
recommendations have been made based on research findings
regarding sustainable waste management, recycling and re-use of the
non-biodegradable products in society.
Abstract: E-retailing is the sale of goods online that takes place
over the Internet. The Internet has shrunk the entire World. World eretailing
is growing at an exponential rate in the Americas, Europe
and Asia. However, e-retailing costs require expensive investment,
such as hardware, software, and security systems. Cloud computing
technology is internet-based computing for the management and
delivery of applications and services. Cloud-based e-retailing
application models allow enterprises to lower their costs with their
effective implementation of e-retailing activities. In this paper, we
describe the concept of cloud computing and present the architecture
of cloud computing, combining the features of e-retailing. In
addition, we propose a strategy for implementing cloud computing
with e-retailing. Finally, we explain the benefits from the
architecture.
Abstract: Erosion and abrasion are wear mechanisms reducing
the lifetime of machine elements like valves, pump and pipe systems.
Both wear mechanisms are acting at the same time, causing a
“Synergy” effect, which leads to a rapid damage of the surface.
Different parameters are effective on erosive abrasive wear rate. In
this study effect of particle impact angle on wear rate and wear
mechanism of ductile and brittle materials was investigated. A new
slurry pot was designed for experimental investigation. As abrasive
particle, silica sand was used. Particle size was ranking between 200-
500 μm. All tests were carried out in a sand-water mixture of 20%
concentration for four hours. Impact velocities of the particles were
4.76 m/s. As ductile material steel St 37 with Vickers Hardness
Number (VHN) of 245 and quenched St 37 with 510 VHN was used
as brittle material. After wear tests, morphology of the eroded
surfaces were investigated for better understanding of the wear
mechanisms acting at different impact angles by using Scanning
Electron Microscope. The results indicated that wear rate of ductile
material was higher than brittle material. Maximum wear rate was
observed by ductile material at a particle impact angle of 300 and
decreased further by an increase in attack angle. Maximum wear rate
by brittle materials was by impact angle of 450 and decreased further
up to 900. Ploughing was the dominant wear mechanism by ductile
material. Microcracks on the surface were detected by ductile
materials, which are nucleation centers for crater formation. Number
of craters decreased and depth of craters increased by ductile
materials by attack angle higher than 300. Deformation wear
mechanism was observed by brittle materials. Number and depth of
pits decreased by brittle materials by impact angles higher than 450.
At the end it is concluded that wear rate could not be directly related
to impact angle of particles due to the different reaction of ductile and
brittle materials.
Abstract: Nitrification is essential to biological processes
designed to remove ammonia and/or total nitrogen. It removes excess
nitrogenous compound in wastewater which could be very toxic to
the aquatic fauna or cause serious imbalance of such aquatic
ecosystem. Efficient nitrification is linked to an in-depth knowledge
of the structure and dynamics of the nitrifying community structure
within the wastewater treatment systems. In this study, molecular
technique was employed for characterizing the microbial structure of
activated sludge [ammonia oxidizing bacteria (AOB) and nitrite
oxidizing bacteria (NOB)] in a municipal wastewater treatment with
intention of linking it to the plant efficiency. PCR based phylogenetic
analysis was also carried out. The average operating and
environmental parameters as well as specific nitrification rate of plant
was investigated during the study. During the investigation the average temperature was 23±1.5oC.
Other operational parameters such as mixed liquor suspended solids
and chemical oxygen demand inversely correlated with ammonia
removal. The dissolved oxygen level in the plant was constantly
lower than the optimum (between 0.24 and 1.267 mg/l) during this
study. The plant was treating wastewater with influent ammonia
concentration of 31.69 and 24.47 mg/L. The influent flow rates
(ML/Day) was 96.81 during period. The dominant nitrifiers include:
Nitrosomonas spp. Nitrobacter spp. and Nitrospira spp. The AOB
had correlation with nitrification efficiency and temperature. This
study shows that the specific ammonia oxidizing rate and the specific
nitrate formation rates can serve as good indicator of the plant overall
nitrification performance.
Abstract: This paper discusses the general methods to saturation
in the steady-state, two axis (d & q) frame models of synchronous
machines. In particular, the important role of the magnetic coupling
between the d-q axes (cross-magnetizing phenomenon), is
demonstrated. For that purpose, distinct methods of saturation
modeling of dumper synchronous machine with cross-saturation are
identified, and detailed models synthesis in d-q axes. A number of
models are given in the final developed form. The procedure and the
novel models are verified by a critical application to prove the
validity of the method and the equivalence between all developed
models is reported. Advantages of some of the models over the
existing ones and their applicability are discussed.
Abstract: There are a number of Distributed Generations (DGs)
installed in microgrid, which may have diverse path and direction of
power flow or fault current. The overcurrent protection scheme for the
traditional radial type distribution system will no longer meet the
needs of microgrid protection. Integrating the Intelligent Electronic
Device (IED) and a Supervisory Control and Data Acquisition
(SCADA) with IEC 61850 communication protocol, the paper
proposes a Microgrid Protection Management System (MPMS) to
protect power system from the fault. In the proposed method, the
MPMS performs logic programming of each IED to coordinate their
tripping sequence. The GOOSE message defined in IEC 61850 is used
as the transmission information medium among IEDs. Moreover, to
cope with the difference in fault current of microgrid between
grid-connected mode and islanded mode, the proposed MPMS applies
the group setting feature of IED to protect system and robust
adaptability. Once the microgrid topology varies, the MPMS will
recalculate the fault current and update the group setting of IED.
Provided there is a fault, IEDs will isolate the fault at once. Finally, the
Matlab/Simulink and Elipse Power Studio software are used to
simulate and demonstrate the feasibility of the proposed method.
Abstract: Sweden has succeeded to maintain a high level of
growth and development and has managed to sustain highly ranked
position among the world’s developed countries. In this regard,
Swedish universities are playing a vital role in supporting innovation
and entrepreneurship at all levels and developing Swedish knowledge
economy. This paper is aiming to draw on the experiences of two leading
Swedish universities, addressing their transformation approach to
create entrepreneurial universities and fulfilling their objectives in the
era of knowledge economy. The objectives of the paper include: 1) Introducing the Swedish
higher education and its characteristics. 2) Examining the
infrastructure elements for innovation and Entrepreneurship at two of
the Swedish entrepreneurial universities. 3) Addressing the key
aspects of support systems in the initiatives of both Chalmers and
Gothenburg universities to support innovation and advance
entrepreneurial practices. The paper will contribute to two discourses: 1) Examining the
relationship between support systems for innovation and
entrepreneurship and the Universities’ policies and practices. 2)
Lessons for University leaders to assist the development and
implementation of effective innovation and entrepreneurship policies
and practices.
Abstract: Hollow section for bridge columns has some
advantages. However, current seismic design codes do not provide
design regulations for hollow bridge piers. There have been many
experimental studied for hollow reinforced concrete piers in the world.
But, Study for hollow section for bridge piers in Korea has been begun
with approximately 2000s. There has been conducted experimental
study for hollow piers of flexural controlled sections by Yeungnam
University, Sung kyunkwan University, Korea Expressway
Corporation in 2009. This study concluded that flexural controlled
sections for hollow piers showed the similar behavior to solid sections.
And there have been conducted experimental study for hollow piers of
compression controlled sections by Yeungnam University, Korea
Institute of Construction Technology in 2012. This study concluded
that compression controlled sections for hollow piers showed
compression fracture of concrete in inside wall face. Samsung
Construction & Trading Corporation has been conducted study with
Yeungnam University for reduce the quantity of reinforcement details
about hollow piers. Reduce the quantity of reinforcement details are
triangular cross tie. This study concluded that triangular reinforcement
details showed the similar behavior as compared with existing
reinforcement details.
Abstract: This study aims to increase understanding of the
transition of business models in servitization. The significance of
service in all business has increased dramatically during the past
decades. Service-dominant logic (SDL) describes this change in the
economy and questions the goods-dominant logic on which business
has primarily been based in the past. A business model canvas is one
of the most cited and used tools in defining end developing business
models. The starting point of this paper lies in the notion that the
traditional business model canvas is inherently goods-oriented and
best suits for product-based business. However, the basic differences
between goods and services necessitate changes in business model
representations when proceeding in servitization. Therefore, new
knowledge is needed on how the conception of business model and
the business model canvas as its representation should be altered in
servitized firms in order to better serve business developers and interfirm
co-creation. That is to say, compared to products, services are
intangible and they are co-produced between the supplier and the
customer. Value is always co-created in interaction between a
supplier and a customer, and customer experience primarily depends
on how well the interaction succeeds between the actors. The role of
service experience is even stronger in service business compared to
product business, as services are co-produced with the customer. This paper provides business model developers with a service
business model canvas, which takes into account the intangible,
interactive, and relational nature of service. The study employs a
design science approach that contributes to theory development via
design artifacts. This study utilizes qualitative data gathered in
workshops with ten companies from various industries. In particular,
key differences between Goods-dominant logic (GDL) and SDLbased
business models are identified when an industrial firm
proceeds in servitization. As the result of the study, an updated version of the business
model canvas is provided based on service-dominant logic. The
service business model canvas ensures a stronger customer focus and
includes aspects salient for services, such as interaction between
companies, service co-production, and customer experience. It can be
used for the analysis and development of a current service business
model of a company or for designing a new business model. It
facilitates customer-focused new service design and service
development. It aids in the identification of development needs, and
facilitates the creation of a common view of the business model.
Therefore, the service business model canvas can be regarded as a
boundary object, which facilitates the creation of a common
understanding of the business model between several actors involved.
The study contributes to the business model and service business
development disciplines by providing a managerial tool for
practitioners in service development. It also provides research insight
into how servitization challenges companies’ business models.
Abstract: This paper will discuss how we optimize our physical
verification flow in our IC Design Department having various rule
decks from multiple foundries. Our ultimate goal is to achieve faster
time to tape-out and avoid schedule delay. Currently the physical
verification runtimes and memory usage have drastically increased
with the increasing number of design rules, design complexity, and
the size of the chips to be verified. To manage design violations, we
use a number of solutions to reduce the amount of violations needed
to be checked by physical verification engineers. The most important
functions in physical verifications are DRC (design rule check), LVS
(layout vs. schematic), and XRC (extraction). Since we have a
multiple number of foundries for our design tape-outs, we need a
flow that improve the overall turnaround time and ease of use of the
physical verification process. The demand for fast turnaround time is
even more critical since the physical design is the last stage before
sending the layout to the foundries.
Abstract: Space Vector Pulse Width Modulation is popular for
variable frequency drives. The method has several advantages over
carried based PWM and is computation intensive. The
implementation of SVPWM for multilevel inverter requires special
attention and at the same time consumes considerable resources. Due
to faster processing power and reduced over all computational
burden, FPGAs are being investigated as an alternative for other
controllers. In this paper, a space vector PWM algorithm is
implemented using FPGA which requires less computational area and
is modular in structure. The algorithm is verified experimentally for
Neutral Point Clamped inverter using FPGA development board
xc3s5000-4fg900.
Abstract: The current tools for real time management of sewer
systems are based on two software tools: the software of weather
forecast and the software of hydraulic simulation. The use of the first
ones is an important cause of imprecision and uncertainty, the use of
the second requires temporal important steps of decision because of
their need in times of calculation. This way of proceeding fact that
the obtained results are generally different from those waited. The major idea of this project is to change the basic paradigm by
approaching the problem by the "automatic" face rather than by that
"hydrology". The objective is to make possible the realization of a
large number of simulations at very short times (a few seconds)
allowing to take place weather forecasts by using directly the real
time meditative pluviometric data. The aim is to reach a system
where the decision-making is realized from reliable data and where
the correction of the error is permanent. A first model of control laws was realized and tested with different
return-period rainfalls. The gains obtained in rejecting volume vary
from 19 to 100 %. The development of a new algorithm was then
used to optimize calculation time and thus to overcome the
subsequent combinatorial problem in our first approach. Finally, this
new algorithm was tested with 16- year-rainfall series. The obtained
gains are 40 % of total volume rejected to the natural environment
and of 65 % in the number of discharges.
Abstract: When high strength reinforced concrete is exposed to
high temperature due to a fire, deteriorations occur such as loss in
strength and elastic modulus, cracking and spalling of the concrete.
Therefore, it is important to understand risk of structural safety in
building structures by studying structural behaviors and rehabilitation
of fire damaged high strength concrete structures. This paper aims at
investigating rehabilitation effect on fire damaged high strength
concrete beams using experimental and analytical methods. In the
experiments, flexural specimens with high strength concrete are
exposed to high temperatures according to ISO 834 standard time
temperature curve. From four-point loading test, results show that
maximum loads of the rehabilitated beams are similar to or higher than
those of the non-fire damaged RC beam. In addition, structural
analyses are performed using ABAQUS 6.10-3 with same conditions
as experiments to provide accurate predictions on structural and
mechanical behaviors of rehabilitated RC beams. The parameters are
the fire cover thickness and strengths of repairing mortar. Analytical
results show good rehabilitation effects, when the results predicted
from the rehabilitated models are compared to structural behaviors of
the non-damaged RC beams. In this study, fire damaged high strength concrete beams are
rehabilitated using polymeric cement mortar. The predictions from the
finite element (FE) models show good agreements with the
experimental results and the modeling approaches can be used to
investigate applicability of various rehabilitation methods for further
study.
Abstract: This paper is aimed to study combustion characteristics
of low NOx burner using petroleum cokes as fuel. The petroleum coke,
which is produced through the oil refining process, is an attractive fuel
in terms of its high heating value and low price. But petroleum coke is
a challenging fuel because of its low volatile content, high sulfur and
nitrogen content, which give rise to undesirable emission
characteristics and low ignitability. Therefore, the research and
development regarding the petroleum coke burner is needed for
applying this industrial system. In this study, combustion and emission
characteristics of petroleum cokes burner are experimentally
investigated in an industrial steam boiler. The low NOx burner is
designed to control fuel and air mixing to achieve staged combustion,
which, in turn reduces both flame temperature and oxygen. Air
distribution ratio of triple staged air is optimized experimentally. The
result showed that NOx concentration is lowest when overfire air is
used, and the burner function at a fuel rich condition. That is, the
burner is operated at the equivalence ratio of 1.67 and overall
equivalence ratio including overfire air is kept 0.87.