Abstract: In this paper, the effects of thermodynamic,
hydrodynamic and geometric of an air cooled condenser on COP of
vapor compression cycle are investigated for a fixed condenser facing
surface area. The system is utilized with a scroll compressor,
modeled based on thermodynamic and heat transfer equations
employing Matlab software. The working refrigerant is R134a whose
thermodynamic properties are called from Engineering Equation
Software. This simulation shows that vapor compression cycle can
be designed by different configurations and COPs, economical and
optimum working condition can be obtained via considering these
parameters.
Abstract: In this paper, an improved technique for contingency
ranking using artificial neural network (ANN) is presented. The
proposed approach is based on multi-layer perceptrons trained by
backpropagation to contingency analysis. Severity indices in dynamic
stability assessment are presented. These indices are based on the
concept of coherency and three dot products of the system variables.
It is well known that some indices work better than others for a
particular power system. This paper along with test results using
several different systems, demonstrates that combination of indices
with ANN provides better ranking than a single index. The presented
results are obtained through the use of power system simulation
(PSS/E) and MATLAB 6.5 software.
Abstract: This paper deals with the tuning of parameters for Automatic Generation Control (AGC). A two area interconnected hydrothermal system with PI controller is considered. Genetic Algorithm (GA) and Particle Swarm optimization (PSO) algorithms have been applied to optimize the controller parameters. Two objective functions namely Integral Square Error (ISE) and Integral of Time-multiplied Absolute value of the Error (ITAE) are considered for optimization. The effectiveness of an objective function is considered based on the variation in tie line power and change in frequency in both the areas. MATLAB/SIMULINK was used as a simulation tool. Simulation results reveal that ITAE is a better objective function than ISE. Performances of optimization algorithms are also compared and it was found that genetic algorithm gives better results than particle swarm optimization algorithm for the problems of AGC.
Abstract: This paper deals with the modeling and the evaluation of a multiplicative phase noise influence on the bit error ratio in a general space communication system. Our research is focused on systems with multi-state phase shift keying modulation techniques and it turns out, that the phase noise significantly affects the bit error rate, especially for higher signal to noise ratios. These results come from a system model created in Matlab environment and are shown in a form of constellation diagrams and bit error rate dependencies. The change of a user data bit rate is also considered and included into simulation results. Obtained outcomes confirm theoretical presumptions.
Abstract: The present work encounters the solution of the defect identification problem with the use of an evolutionary algorithm combined with a simplex method. In more details, a Matlab implementation of Genetic Algorithms is combined with a Simplex method in order to lead to the successful identification of the defect. The influence of the location and the orientation of the depressed ellipsoidal flaw was investigated as well as the use of different amount of static data in the cost function. The results were evaluated according to the ability of the simplex method to locate the global optimum in each test case. In this way, a clear impression regarding the performance of the novel combination of the optimization algorithms, and the influence of the geometrical parameters of the flaw in defect identification problems was obtained.
Abstract: The object of this paper is to design and analyze a
proportional – integral (PI) control for positive output elementary
super lift Luo converter (POESLLC), which is the start-of-the-art
DC-DC converter. The positive output elementary super lift Luo
converter performs the voltage conversion from positive source
voltage to positive load voltage. This paper proposes a
development of PI control capable of providing the good static and
dynamic performance compared to proportional – integralderivative
(PID) controller. Using state space average method
derives the dynamic equations describing the positive output
elementary super lift luo converter and PI control is designed. The
simulation model of the positive output elementary super lift Luo
converter with its control circuit is implemented in
Matlab/Simulink. The PI control for positive output elementary
super lift Luo converter is tested for transient region, line changes,
load changes, steady state region and also for components
variations.
Abstract: This paper introduces a hand gesture recognition system to recognize real time gesture in unstrained environments. Efforts should be made to adapt computers to our natural means of communication: Speech and body language. A simple and fast algorithm using orientation histograms will be developed. It will recognize a subset of MAL static hand gestures. A pattern recognition system will be using a transforrn that converts an image into a feature vector, which will be compared with the feature vectors of a training set of gestures. The final system will be Perceptron implementation in MATLAB. This paper includes experiments of 33 hand postures and discusses the results. Experiments shows that the system can achieve a 90% recognition average rate and is suitable for real time applications.
Abstract: Multimedia information availability has increased
dramatically with the advent of video broadcasting on handheld
devices. But with this availability comes problems of maintaining the
security of information that is displayed in public. ISMA Encryption
and Authentication (ISMACryp) is one of the chosen technologies for
service protection in DVB-H (Digital Video Broadcasting-
Handheld), the TV system for portable handheld devices. The
ISMACryp is encoded with H.264/AVC (advanced video coding),
while leaving all structural data as it is. Two modes of ISMACryp are
available; the CTR mode (Counter type) and CBC mode (Cipher
Block Chaining) mode. Both modes of ISMACryp are based on 128-
bit AES algorithm. AES algorithms are more complex and require
larger time for execution which is not suitable for real time
application like live TV. The proposed system aims to gain a deep
understanding of video data security on multimedia technologies and
to provide security for real time video applications using selective
encryption for H.264/AVC. Five level of security proposed in this
paper based on the content of NAL unit in Baseline Constrain profile
of H.264/AVC. The selective encryption in different levels provides
encryption of intra-prediction mode, residue data, inter-prediction
mode or motion vectors only. Experimental results shown in this
paper described that fifth level which is ISMACryp provide higher
level of security with more encryption time and the one level provide
lower level of security by encrypting only motion vectors with lower
execution time without compromise on compression and quality of
visual content. This encryption scheme with compression process
with low cost, and keeps the file format unchanged with some direct
operations supported. Simulation was being carried out in Matlab.
Abstract: The design of Automatic Generation Control (AGC) system plays a vital role in automation of power system. This paper proposes Hybrid Neuro Fuzzy (HNF) approach for AGC of two-area interconnected reheat thermal power system with the consideration of Generation Rate Constraint (GRC). The advantage of proposed controller is that it can handle the system non-linearities and at the same time the proposed approach is faster than conventional controllers. The performance of HNF controller has been compared with that of both conventional Proportional Integral (PI) controller as well as Fuzzy Logic Controller (FLC) both in the absence and presence of Generation Rate Constraint (GRC). System performance is examined considering disturbance in each area of interconnected power system.
Abstract: High precision in motion is required to manipulate the
micro objects in precision industries for micro assembly, cell
manipulation etc. Precision manipulation is achieved based on the
appropriate mechanism design of micro devices such as
microgrippers. Design of a compliant based mechanism is the better
option to achieve a highly precised and controlled motion. This
research article highlights the method of designing a compliant based
three fingered microgripper suitable for holding asymmetric objects.
Topological optimization technique, a systematic method is
implemented in this research work to arrive a topologically optimized
design of the mechanism needed to perform the required micro
motion of the gripper. Optimization technique has a drawback of
generating senseless regions such as node to node connectivity and
staircase effect at the boundaries. Hence, it is required to have post
processing of the design to make it manufacturable. To reduce the
effect of post processing stage and to preserve the edges of the image,
a cubic spline interpolation technique is introduced in the MATLAB
program. Structural performance of the topologically developed
mechanism design is tested using finite element method (FEM)
software. Further the microgripper structure is examined to find its
fatigue life and vibration characteristics.
Abstract: In the present paper, active control system is used in
different heights of the building and the most effective part was
studied where the active control system is applied. The mathematical
model of the building is established in MATLAB and in order to
active control the system FLC method was used. Three different
locations of the building are chosen to apply active control system,
namely at the lowest story, the middle height of the building, and at
the highest point of the building with TMD system. The equation of
motion was written for high rise building and it was solved by statespace
method. Also passive control was used with Tuned Mass
Damper (TMD) at the top floor of the building to show the robustness
of FLC method when compared with passive control system.
Abstract: The problem of robust stability and robust stabilization for a class of discrete-time uncertain systems with time delay is investigated. Based on Tchebychev inequality, by constructing a new augmented Lyapunov function, some improved sufficient conditions ensuring exponential stability and stabilization are established. These conditions are expressed in the forms of linear matrix inequalities (LMIs), whose feasibility can be easily checked by using Matlab LMI Toolbox. Compared with some previous results derived in the literature, the new obtained criteria have less conservatism. Two numerical examples are provided to demonstrate the improvement and effectiveness of the proposed method.
Abstract: This paper studies the mean square exponential synchronization problem of a class of stochastic neutral type chaotic neural networks with mixed delay. On the Basis of Lyapunov stability theory, some sufficient conditions ensuring the mean square exponential synchronization of two identical chaotic neural networks are obtained by using stochastic analysis and inequality technique. These conditions are expressed in the form of linear matrix inequalities (LMIs), whose feasibility can be easily checked by using Matlab LMI Toolbox. The feedback controller used in this paper is more general than those used in previous literatures. One simulation example is presented to demonstrate the effectiveness of the derived results.
Abstract: With the advent of inexpensive 32 bit floating point digital signal processor-s availability in market, many computationally intensive algorithms such as Kalman filter becomes feasible to implement in real time. Dynamic simulation of a self excited DC motor using second order state variable model and implementation of Kalman Filter in a floating point DSP TMS320C6713 is presented in this paper with an objective to introduce and implement such an algorithm, for beginners. A fractional hp DC motor is simulated in both Matlab® and DSP and the results are included. A step by step approach for simulation of DC motor in Matlab® and “C" routines in CC Studio® is also given. CC studio® project file details and environmental setting requirements are addressed. This tutorial can be used with 6713 DSK, which is based on floating point DSP and CC Studio either in hardware mode or in simulation mode.
Abstract: The highly nonlinear characteristics of drying
processes have prompted researchers to seek new nonlinear control
solutions. However, the relation between the implementation
complexity, on-line processing complexity, reliability control
structure and controller-s performance is not well established. The
present paper proposes high performance nonlinear fuzzy controllers
for a real-time operation of a drying machine, being developed under
a consistent match between those issues. A PCI-6025E data
acquisition device from National Instruments® was used, and the
control system was fully designed with MATLAB® / SIMULINK
language. Drying parameters, namely relative humidity and
temperature, were controlled through MIMOs Hybrid Bang-bang+PI
(BPI) and Four-dimensional Fuzzy Logic (FLC) real-time-based
controllers to perform drying tests on biological materials. The
performance of the drying strategies was compared through several
criteria, which are reported without controllers- retuning. Controllers-
performance analysis has showed much better performance of FLC
than BPI controller. The absolute errors were lower than 8,85 % for
Fuzzy Logic Controller, about three times lower than the
experimental results with BPI control.
Abstract: In this paper effect of stator slots structure and
switching angle on a cylindrical single-phase brushless direct current
motor (BLDC) is analyzed. BLDC motor with three different
structures for stator slots is designed by using RMxprt software and
efficiency of BLDC motor for different structures in full-load
condition has been presented. Then the BLDC motor in different
conditions by using Maxwell 3D software is designed and with finite
element method is analyzed electromagnetically. At the end with the
use of MATLAB software influence of switching angle on motor
performance investigated and optimal angle has been determined.
The results indicate that with correct choosing of stator slots structure
and switching angle, maximum efficiency can be found.
Abstract: This paper presents a new high speed simulation methodology to solve the long simulation time problem of CMOS image sensor matrix. Generally, for integrating the pixel matrix in SOC and simulating the system performance, designers try to model the pixel in various modeling languages such as VHDL-AMS, SystemC or Matlab. We introduce a new alternative method based on spice model in cadence design platform to achieve accuracy and reduce simulation time. The simulation results indicate that the pixel output voltage maximum error is at 0.7812% and time consumption reduces from 2.2 days to 13 minutes achieving about 240X speed-up for the 256x256 pixel matrix.
Abstract: Induction motors are being used in greater numbers
throughout a wide variety of industrial and commercial applications
because it provides many benefits and reliable device to convert the
electrical energy into mechanical motion. In some application it-s
desired to control the speed of the induction motor. Because of the
physics of the induction motor the preferred method of controlling its
speed is to vary the frequency of the AC voltage driving the motor. In
recent years, with the microcontroller incorporated into an appliance
it becomes possible to use it to generate the variable frequency AC
voltage to control the speed of the induction motor.
This study investigates the microcontroller based variable
frequency power inverter. the microcontroller is provide the variable
frequency pulse width modulation (PWM) signal that control the
applied voltage on the gate drive, which is provides the required
PWM frequency with less harmonics at the output of the power
inverter.
The fully controlled bridge voltage source inverter has been
implemented with semiconductors power devices isolated gate
bipolar transistor (IGBT), and the PWM technique has been
employed in this inverter to supply the motor with AC voltage.
The proposed drive system for three & single phase power inverter
is simulated using Matlab/Simulink. The Matlab Simulation Results
for the proposed system were achieved with different SPWM. From
the result a stable variable frequency inverter over wide range has
been obtained and a good agreement has been found between the
simulation and hardware of a microcontroller based single phase
inverter.
Abstract: This paper describes a steady state model of a multiple
effect evaporator system for simulation and control purposes. The
model includes overall as well as component mass balance equations,
energy balance equations and heat transfer rate equations for area
calculations for all the effects. Each effect in the process is
represented by a number of variables which are related by the energy
and material balance equations for the feed, product and vapor flow
for backward, mixed and split feed. For simulation 'fsolve' solver in
MATLAB source code is used. The optimality of three sequences i.e.
backward, mixed and splitting feed is studied by varying the various
input parameters.
Abstract: End milling process is one of the common metal
cutting operations used for machining parts in manufacturing
industry. It is usually performed at the final stage in manufacturing a
product and surface roughness of the produced job plays an
important role. In general, the surface roughness affects wear
resistance, ductility, tensile, fatigue strength, etc., for machined parts
and cannot be neglected in design. In the present work an
experimental investigation of end milling of aluminium alloy with
carbide tool is carried out and the effect of different cutting
parameters on the response are studied with three-dimensional
surface plots. An artificial neural network (ANN) is used to establish
the relationship between the surface roughness and the input cutting
parameters (i.e., spindle speed, feed, and depth of cut). The Matlab
ANN toolbox works on feed forward back propagation algorithm is
used for modeling purpose. 3-12-1 network structure having
minimum average prediction error found as best network architecture
for predicting surface roughness value. The network predicts surface
roughness for unseen data and found that the result/prediction is
better. For desired surface finish of the component to be produced
there are many different combination of cutting parameters are
available. The optimum cutting parameter for obtaining desired
surface finish, to maximize tool life is predicted. The methodology is
demonstrated, number of problems are solved and algorithm is coded
in Matlab®.