Abstract: In this study, we examine some spectral properties
of non-selfadjoint matrix-valued difference equations consisting of
a polynomial-type Jost solution. The aim of this study is to
investigate the eigenvalues and spectral singularities of the difference
operator L which is expressed by the above-mentioned difference
equation. Firstly, thanks to the representation of polynomial type Jost
solution of this equation, we obtain asymptotics and some analytical
properties. Then, using the uniqueness theorems of analytic functions,
we guarantee that the operator L has a finite number of eigenvalues
and spectral singularities.
Abstract: Public participation in recycling domestic waste is still
very low in Malaysia. Only 10.5% of solid waste was recycled up to
now which is far below than of in developed countries. Therefore,
understanding public motivations towards recycling domestic waste
are important to improve current recycling rate. Thus, this study
attempts to identify what are the possible motivations and hindrances
for the public to recycle. Open-ended questions format were
administered to 484 people in Kota Kinabalu, Sabah, Malaysia. Two
specific questions we asked to explore their general determinants and
barriers in practicing recycling: “What motivates you to recycle?”
and “What are the barriers you encountered in doing recycling
activities?” Thematic was conducted on the open-ended questions in
which themes were created with the raw comments. It was found that
the underlying recycling motivations are (i) awareness’ towards the
environment; (ii) benefits to the society and individual; and (iii)
social influence. Non participations are influence by (i) attitudes; (ii)
commitment; (iii) facilities; (iv) knowledge; (v) inconvenience; and
(vi) enforcement.
Abstract: On account of the concern of the fossil fuel is
depleting and its negative effects on the environment, interest in
alternative energy sources is increasing day by day. However,
considering the importance of transportation in human life, instead of
oil and its derivatives fueled vehicles with internal combustion
engines, electric vehicles which are sensitive to the environment and
working with electrical energy has begun to develop. In this study,
simulation was carried out for providing energy management and
recovering regenerative braking in fuel cell-battery hybrid electric
vehicle. The main power supply of the vehicle is fuel cell on the other
hand not only instantaneous power is supplied by the battery but also
the energy generated due to regenerative breaking is stored in the
battery. Obtained results of the simulation is analyzed and discussed.
Abstract: In this paper, a asymptotically periodic predator-prey
model with Modified Leslie-Gower and Holling-Type II schemes
is investigated. Some sufficient conditions for the uniformly strong
persistence of the system are established. Our result is an important
complementarity to the earlier results.
Abstract: A mixed method for model order reduction is
presented in this paper. The denominator polynomial is derived by
matching both Markov parameters and time moments, whereas
numerator polynomial derivation and error minimization is done
using Genetic Algorithm. The efficiency of the proposed method can
be investigated in terms of closeness of the response of reduced order
model with respect to that of higher order original model and a
comparison of the integral square error as well.
Abstract: Friction stir welding and tungsten inert gas welding
techniques were employed to weld armor grade aluminum alloy to
investigate the effect of welding processes on tensile behavior of
weld joints. Tensile tests, Vicker microhardness tests and optical
microscopy were performed on developed weld joints and base metal.
Welding process influenced tensile behavior and microstructure of
weld joints. Friction stir welded joints showed tensile behavior better
than tungsten inert gas weld joints.
Abstract: One of the tasks of optical surveillance is to detect
anomalies in large amounts of image data. However, if the size of the
anomaly is very small, limited information is available to distinguish
it from the surrounding environment. Spectral detection provides a
useful source of additional information and may help to detect
anomalies with a size of a few pixels or less. Unfortunately, spectral
cameras are expensive because of the difficulty of separating two
spatial in addition to one spectral dimension. We investigate the
possibility of modifying a simple spectral line detector for outdoor
detection. This may be especially useful if the area of interest forms a
line, such as the horizon. We use a monochrome CCD that also
enables detection into the near infrared. A simple camera is attached
to the setup to determine which part of the environment is spectrally
imaged. Our preliminary results indicate that sensitive detection of
very small targets is indeed possible. Spectra could be taken from the
various targets by averaging columns in the line image. By imaging a
set of lines of various widths we found narrow lines that could not be
seen in the color image but remained visible in the spectral line
image. A simultaneous analysis of the entire spectra can produce
better results than visual inspection of the line spectral image. We are
presently developing calibration targets for spatial and spectral
focusing and alignment with the spatial camera. This will present
improved results and more use in outdoor application.
Abstract: The reheating furnace is used to reheat the steel slabs
before the hot-rolling process. The supported system includes the
stationary/moving beams, and the skid buttons which block some
thermal radiation transmitted to the bottom of the slabs. Therefore, it is
important to analyze the steel slab temperature distribution during the
heating period. A three-dimensional mathematical transient heat
transfer model for the prediction of temperature distribution within the
slab has been developed. The effects of different skid button height
(H=60mm, 90mm, and 120mm) and different gap distance between
two slabs (S=50mm, 75mm, and 100mm) on the slab skid mark
formation and temperature profiles are investigated. Comparison with
the in-situ experimental data from Steel Company in Taiwan shows
that the present heat transfer model works well for the prediction of
thermal behavior of the slab in the reheating furnace. It is found that
the skid mark severity decreases with an increase in the skid button
height. The effect of gap distance is important only for the slab edge
planes, while it is insignificant for the slab central planes.
Abstract: Automated Teller Machines (ATMs) can be
considered among one of the most important service facilities in the
banking industry. The investment in ATMs and the impact on the
banking industry is growing steadily in every part of the world. The
banks take into consideration many factors like safety, convenience,
visibility, and cost in order to determine the optimum locations of
ATMs. Today, ATMs are not only available in bank branches but
also at retail locations. Another important factor is the cash
management in ATMs. A cash demand model for every ATM is
needed in order to have an efficient cash management system. This
forecasting model is based on historical cash demand data which is
highly related to the ATMs location. So, the location and the cash
management problem should be considered together. This paper
provides a general review on studies, efforts and development in
ATMs location and cash management problem.
Abstract: Wicking and evaporation of water in porous knitted fabrics is investigated by combining experimental and analytical approaches: The standard wicking model from Lucas and Washburn is enhanced to account for evaporation and gravity effects. The goal is to model the effect of gravity and evaporation on wicking using simple analytical expressions and investigate the influence of fabrics geometrical parameters, such as porosity and thickness on evaporation impact on maximum reachable height values. The results show that fabric properties have a significant influence on evaporation effect. In this paper, an experimental study of determining water kinetics from different knitted fabrics were gravimetrically investigated permitting the measure of the mass and the height of liquid rising in fabrics in various atmospheric conditions. From these measurements, characteristic pore parameters (capillary radius and permeability) can be determined.
Abstract: This study aims at improving the urban hydrological
cycle of the Orléans agglomeration (France) and understanding the
relationship between physical and chemical parameters of urban
surface runoff and the hydrological conditions. In particular water
quality parameters such as pH, conductivity, total dissolved solids,
major dissolved cations and anions, and chemical and biological
oxygen demands were monitored for three types of urban water
discharges (wastewater treatment plant output (WWTP), storm
overflow and stormwater outfall) under two hydrologic scenarios (dry
and wet weather). The first results were obtained over a period of five
months. Each investigated (Ormes, l’Egoutier and La Corne) outfall
represents an urban runoff source that receives water from runoff
roads, gutters, the irrigation of gardens and other sources of flow over
the Earth’s surface that drains in its catchments and carries it to the
Loire River. In wet weather conditions there is rain water runoff and
an additional input from the roof gutters that have entered the
stormwater system during rainfall. For the comparison the results La
Chilesse is a storm overflow that was selected in our study as a
potential source of waste water which is located before the (WWTP). The comparison of the physical-chemical parameters (total
dissolved solids, turbidity, pH, conductivity, dissolved organic
carbon (DOC), concentration of major cations and anions) together
with the chemical oxygen demand (COD) and biological oxygen
demand (BOD) helped to characterize sources of runoff waters in the
different watersheds. It also helped to highlight the infiltration of
wastewater in some stormwater systems that reject directly in the
Loire River. The values of the conductivity measured in the outflow
of Ormes were always higher than those measured in the other two
outlets. The results showed a temporal variation for the Ormes outfall
of conductivity from 1465 μS cm-1 in the dry weather flow to 650 μS
cm-1 in the wet weather flow and also a spatial variation in the wet
weather flow from 650 μS cm-1 in the Ormes outfall to 281 μS cm-1
in L’Egouttier outfall. The ultimate BOD (BOD28) showed a
significant decrease in La Corne outfall from 181 mg L-1 in the wet
weather flow to 95 mg L-1 in the dry weather flow because of the
nutrient load that was transported by the runoff.
Abstract: Red pepper (Capsicum annum L.) has long been
recognized as a good source of antioxidants, being rich in ascorbic
acid and other phytochemicals. In Turkish cuisine red pepper is
sometimes consumed raw in salads and baked as a garnish, but its
most wide consumption type is red pepper paste. The processing of
red pepper into pepper paste includes various thermal treatment steps
such as heating and pasteurizing. There are reports demonstrating an
enhancement or reduction in antioxidant activity of vegetables after
thermal treatment. So this study was conducted to investigate the
total phenolic, ascorbic acid and total carotenoids as well as free
radical scavenging activity of raw red pepper and various red pepper
pastes obtainable on the market. The samples were analyzed for
radical-scavenging activity (RSA) and total polyphenol (TP) content
using 1,1-diphenyl-2-picrylhydrazyl (DPPH) and Folin-Ciocalteu
methods, respectively. Total carotenoids and ascorbic acid contents
were determined spectrophotometrically. Results suggest that hot
pepper paste contained significantly (P0.05) difference in RSA, ascorbic acid and total carotenoids
content between sweet and hot red pepper paste products. It is
concluded that the red pepper paste, that has a wide range of
consumption in Turkish cuisine, presents a good dose of phenolic
compounds and antioxidant capacity and it should be regarded as a
functional food.
Abstract: A large variety of pipe flange is required in marine
and construction industry. Pipe flanges are usually welded or screwed
to the pipe end and are connected with bolts. This approach is very
simple and widely used for a long time; however, it results in high
development cost and low productivity, and the productions made by
this approach usually have safety problem at the welding area. In this
research, a new approach of forming pipe flange based on cold
forging and floating die concept is presented. This innovative
approach increases the effectiveness of the material usage and save
the time cost compared with conventional welding method. To ensure the dimensional accuracy of the final product, the finite
element analysis (FEA) was carried out to simulate the process of
cold forging, and the orthogonal experiment methods were used to
investigate the influence of four manufacturing factors (pin die angle,
pipe flange angle, rpm, pin die distance from clamp jig) and predicted
the best combination of them. The manufacturing factors were
obtained by numerical and experimental studies and it shows that the
approach is very useful and effective for the forming of pipe flange,
and can be widely used later.
Abstract: The market competition is moving from the single
firm to the whole supply chain because of increasing competition and
growing need for operational efficiencies and customer orientation.
Supply chain management allows companies to look beyond their
organizational boundaries to develop and leverage resources and
capabilities of their supply chain partners. This creates competitive
advantages in the marketplace and because of this SCM has acquired
strategic importance. Lean Approach is a management strategy that focuses on reducing
every type of waste present in an organization. This approach is
becoming more and more popular among supply chain managers. The supply chain application of lean approach is not frequent. In
particular, it is not well studied which are the impacts of lean
approach principles in a supply chain context. In literature there are
only few studies aimed at understanding the qualitative impact of the
lean approach in supply chains. Therefore, the goal of this research
work is to study the impacts of lean principles implementation along
a supply chain. To achieve this, a simulation model of a threeechelon
multi-product supply chain has been built. Kanban system (and several priority policies) and setup time
reduction degrees are implemented in the lean-configured supply
chain to apply pull and lot-sizing decrease principles respectively. To
evaluate the benefits of lean approach, lean supply chain is compared
with an EOQ-configured supply chain. The simulation results show
that Kanban system and setup-time reduction improve inventory
stock level. They also show that logistics efforts are affected to lean
implementation degree. The paper concludes describing
performances of lean supply chain in different contexts.
Abstract: Optimizing the parameters in the controller plays a
vital role in the control theory and its applications. Optimizing the
PID parameters is finding out the best value from the feasible
solutions. Finding the optimal value is an optimization problem.
Inverted Pendulum is a very good platform for control engineers to
verify and apply different logics in the field of control theory. It is
necessary to find an optimization technique for the controller to tune
the values automatically in order to minimize the error within the
given bounds. In this paper, the algorithmic concepts of Harmony
search (HS) and Genetic Algorithm (GA) have been analyzed for the
given range of values. The experimental results show that HS
performs well than GA.
Abstract: The study investigated efficiency cassava peel carbon
and Zinc Chloride activated cassava peel carbon at 1:3, 2:3 and 1:1
activation levels in the removal of nitrates from oxidized cassava
processing wastewater. Results showed that the CPC and CPAC were
effective in adsorption of nitrates. A summary of results from the
study revealed that CPAC at 1:3 exhibited the highest initial
decontamination (69.5% after 2 hrs) while CPAC at 1:1 activation
ratio showed a slower initial decontamination rate. The CPC &
CPAC exhibited Langmuir Rα values of 0.15, 0.11, 0.09, and 0.07 for
the 0:1, 1:3, 2:3 and 1:1 confirming its suitability as adsorption
material.
Abstract: Processing of high-silicon bauxite on the base of the
traditional clinkering method is related to high power consumption
and capital investments, which makes production of alumina from
those ores non-competitive in terms of basic economic showings. For
these reasons, development of technological solutions enabling to
process bauxites with various chemical and mineralogical structures
efficiently with low level of thermal power consumption is important.
Flow sheet of the studies on washability of ores from the Timanskoe
and the Severo-Onezhskoe deposits is on the base of the flotation
method.
Abstract: This work deals with the problem of MHD mixed
convection in a completely porous and differentially heated vertical
channel. The model of Darcy-Brinkman-Forchheimer with the
Boussinesq approximation is adopted and the governing equations are
solved by the finite volume method. The effects of magnetic field and
buoyancy force intensities are given by the Hartmann and Richardson
numbers respectively, as well as the Joule heating represented by
Eckert number on the velocity and temperature fields, are examined.
The main results show an augmentation of heat transfer rate with the
decrease of Darcy number and the increase of Ri and Ha when Joule
heating is neglected.
Abstract: The research explores the relationship between
management responsibility and corporate governance of listed
companies in Kazakhstan. This research employs firm level data of
selected listed non-financial firms and firm level data “operational”
financial sector, consisted from banking sector, insurance companies
and accumulated pension funds using multivariate regression analysis
under fixed effect model approach. Ownership structure includes
institutional ownership, managerial ownership and private investor’s
ownership. Management responsibility of the firm is expressed by the
decision of the firm on amount of leverage. Results of the cross
sectional panel study for non-financial firms showed that only
institutional shareholding is significantly negatively correlated with
debt to equity ratio. Findings from “operational” financial sector
show that leverage is significantly affected only by the CEO/Chair
duality and the size of financial institutions, and insignificantly
affected by ownership structure. Also, the findings show, that there is
a significant negative relationship between profitability and the debt
to equity ratio for non-financial firms, which is consistent with
pecking order theory. Generally, the found results suggest that
corporate governance and a management responsibility play
important role in corporate performance of listed firms in
Kazakhstan.
Abstract: Our sowing date experiment took place in the
Demonstration Garden of Institution of Plant Sciences, Centre for
Agricultural Sciences of University of Debrecen, in 2012-2014. The
paper contains data of test year 2014. Our purpose, besides several
other examinations, was to observe how sowing date influences the
leaf area index and the activity of photosynthesis of maize hybrids,
and how those factors affect fruiting. In the experiment we monitored
the change of the leaf area index and the photosynthesis of hybrids
with four different growing seasons. The results obtained confirm
that not only the environmental and agricultural factors in the
growing season have effect on the yield, but also other factors like
the leaf area index and the photosynthesis are determinative
parameters, and all those factors together, modifying the effects of
each other, develop average yields.