Abstract: Steel tubular towers serving as support structures for large wind turbines are subjected to several hundred million stress cycles caused by the turbulent nature of the wind. This causes highcycle fatigue, which could govern the design of the tower. Maintaining the support structure after the wind turbines reach its typical 20-year design life has become a common practice; however, quantifying the changes in the reliability on the tower is not usual. In this paper the effect of fatigue damage in the wind turbine structure is studied whit the use of fracture mechanics, and a method to estimate the reliability over time of the structure is proposed. A representative wind turbine located in Oaxaca, Mexico is then studied. It is found that the system reliability is significantly affected by the accumulation of fatigue damage.
Abstract: The distribution of a single global clock across a chip
has become the major design bottleneck for high performance VLSI
systems owing to the power dissipation, process variability and multicycle
cross-chip signaling. A Network-on-Chip (NoC) architecture
partitioned into several synchronous blocks has become a promising
approach for attaining fine-grain power management at the system
level. In a NoC architecture the communication between the blocks is
handled asynchronously. To interface these blocks on a chip
operating at different frequencies, an asynchronous FIFO interface is
inevitable. However, these asynchronous FIFOs are not required if
adjacent blocks belong to the same clock domain. In this paper, we
have designed and analyzed a 16-bit asynchronous micropipelined
FIFO of depth four, with the awareness of place and route on an
FPGA device. We have used a commercially available Spartan 3
device and designed a high speed implementation of the
asynchronous 4-phase micropipeline. The asynchronous FIFO
implemented on the FPGA device shows 76 Mb/s throughput and a
handshake cycle of 109 ns for write and 101.3 ns for read at the
simulation under the worst case operating conditions (voltage =
0.95V) on a working chip at the room temperature.
Abstract: The thermal performance of a solar water heating with
1.00 m2 flat plate collectors in Cascavel - PR, is which presented in
this article, paper presents the solution to leverage the marketing of
solar heating systems through detailed constituent materials of the
solar collector studies, these abundant materials in construction, such
as expanded polyethylene, PVC, aluminum and glass tubes, mixing
them with new materials to minimize loss of efficiency while
decreasing its cost. The system was tested during months and the
collector obtained maximum recorded temperature of outlet fluid of
55°C, while the maximum temperature of the water at the bottom of
the hot water tank was 35°C. The average daily energy collected was
19.6 MJ/d; the energy supplied by the solar plate was 16.2 MJ/d; the
loss in the feed pipe was 3.2 MJ/d; the solar fraction was 32.2%, the
efficiency of the collector was 45.6% and the efficiency of the system
was 37.8%.
Abstract: In emerging economies, recycling is an opportunity
for the cities to increase the lifespan of sanitary landfills, reduce the
costs of the solid waste management, decrease the environmental
problems of the waste treatment through reincorporate waste in the
productive cycle and protect and develop people’s livelihoods of
informal waste pickers. However, few studies have analysed the
possibilities and strategies to integrate formal and informal sectors in
the solid waste management for the benefit of both. This study seek
to make a strength, weakness, opportunity, and threat (SWOT)
analysis in three recycling associations of Bogotá with the aim to
understand and determine the situation of recycling from perspective
of informal sector in its transition to enter as authorized waste
providers. Data used in the analysis are derived from multiple
strategies such as literature review, the Bogota’s recycling database,
focus group meetings, governmental reports, national laws and
regulations and specific interviews with key stakeholders. Results of
this study show as the main stakeholders of formal and informal
sector of waste management can identify the internal and internal
conditions of recycling in Bogotá. Several strategies were designed
based on the SWOTs determined, could be useful for Bogotá to
advance and promote recycling as a key strategy for integrated
sustainable waste management in the city.
Abstract: Verification of vented wooden façade system with
bonded joints is presented in this paper. The potential of bonded
joints is studied and described in more detail. The paper presents the results of an experimental and theoretical research about the effects of freeze cycling on the bonded joint. For the purpose of tests spruce
timber profiles were chosen for the load bearing substructure. Planks from wooden plastic composite and Siberian larch are representing facade cladding. Two types of industrial polyurethane adhesives intended for structural bonding were selected. The article is focused on the preparation as well as on the subsequent curing and conditioning of test samples. All test samples were subjected to 15 cycles that represents sudden temperature changes, i.e. immersion in a water bath at (293.15 ± 3) K for 6 hours and subsequent freezing to (253.15 ± 2) K for 18 hours. Furthermore, the retention of bond strength between substructure and cladding wastested and strength in shear was determined under tensile stress.Research data indicate that little, if any, damage to the bond results from freezingcycles. Additionally, the suitability of selected group of adhesives in combination with timber substructure was confirmed.
Abstract: In the current work, a three-dimensional geometry of a
75% stenosed blood vessel is analyzed. Large eddy simulation (LES)
with the help of a dynamic subgrid scale Smagorinsky model is
applied to model the turbulent pulsatile flow. The geometry, the
transmural pressure and the properties of the blood and the elastic
boundary were based on clinical measurement data. For the flexible
wall model, a thin solid region is constructed around the 75%
stenosed blood vessel. The deformation of this solid region was
modelled as a deforming boundary to reduce the computational cost
of the solid model. Fluid-structure interaction is realized via a twoway
coupling between the blood flow modelled via LES and the
deforming vessel. The information of the flow pressure and the wall
motion was exchanged continually during the cycle by an arbitrary
Lagrangian-Eulerian method. The boundary condition of current time
step depended on previous solutions. The fluctuation of the velocity
in the post-stenotic region was analyzed in the study. The axial
velocity at normalized position Z=0.5 shows a negative value near
the vessel wall. The displacement of the elastic boundary was
concerned in this study. In particular, the wall displacement at the
systole and the diastole were compared. The negative displacement at
the stenosis indicates a collapse at the maximum velocity and the
deceleration phase.
Abstract: The biodegradable family of polymers
polyhydroxyalkanoates is an interesting substitute for convectional
fossil-based plastics. However, the manufacturing and environmental
impacts associated with their production via intracellular bacterial
fermentation are strongly dependent on the raw material used and on
energy consumption during the extraction process, limiting their
potential for commercialization. Industrial wastewater is studied in
this paper as a promising alternative feedstock for waste valorization.
Based on results from laboratory and pilot-scale experiments, a
conceptual process design, techno-economic analysis and life cycle
assessment are developed for the large-scale production of the most
common type of polyhydroxyalkanoate, polyhydroxbutyrate.
Intracellular polyhydroxybutyrate is obtained via fermentation of
microbial community present in industrial wastewater and the
downstream processing is based on chemical digestion with
surfactant and hypochlorite. The economic potential and
environmental performance results help identifying bottlenecks and
best opportunities to scale-up the process prior to industrial
implementation. The outcome of this research indicates that the
fermentation of wastewater towards PHB presents advantages
compared to traditional PHAs production from sugars because the
null environmental burdens and financial costs of the raw material in
the bioplastic production process. Nevertheless, process optimization
is still required to compete with the petrochemicals counterparts.
Abstract: Phelipanche ramosa is the most damaging obligate
flowering parasitic weed on wide species of cultivated plants. The
semi-arid regions of the world are considered the main centers of this
parasitic plant that causes heavy infestation. This is due to its
production of high numbers of seeds (up to 200,000) that remain
viable for extended periods (up to 20 years). In this study, 13
treatments for the control of Phelipanche were carried out, which
included agronomic, chemical, and biological treatments and the use
of resistant plant methods. In 2014, a trial was performed at the
Department of Agriculture, Food and Environment, University of
Foggia (southern Italy), on processing tomato (cv ‘Docet’) grown in
pots filled with soil taken from a field that was heavily infested by P.
ramosa). The tomato seedlings were transplanted on May 8, 2014,
into a sandy-clay soil (USDA). A randomized block design with 3
replicates (pots) was adopted. During the growing cycle of the
tomato, at 70, 75, 81 and 88 days after transplantation, the number of
P. ramosa shoots emerged in each pot was determined. The tomato
fruit were harvested on August 8, 2014, and the quantitative and
qualitative parameters were determined. All of the data were
subjected to analysis of variance (ANOVA) using the JMP software
(SAS Institute Inc. Cary, NC, USA), and for comparisons of means
(Tukey's tests). The data show that each treatment studied did not
provide complete control against P. ramosa. However, the virulence
of the attacks was mitigated by some of the treatments tried: radicon
biostimulant, compost activated with Fusarium, mineral fertilizer
nitrogen, sulfur, enzone, and the resistant tomato genotype. It is
assumed that these effects can be improved by combining some of
these treatments with each other, especially for a gradual and
continuing reduction of the “seed bank” of the parasite in the soil.
Abstract: Parabolic solar trough systems have seen limited
deployments in cold northern climates as they are more suitable for
electricity production in southern latitudes. A numerical dynamic
model is developed to simulate troughs installed in cold climates and
validated using a parabolic solar trough facility in Winnipeg. The
model is developed in Simulink and will be utilized to simulate a trigeneration
system for heating, cooling and electricity generation in
remote northern communities. The main objective of this simulation
is to obtain operational data of solar troughs in cold climates and use
the model to determine ways to improve the economics and address
cold weather issues.
In this paper the validated Simulink model is applied to simulate a
solar assisted absorption cooling system along with electricity
generation using Organic Rankine Cycle (ORC) and thermal storage.
A control strategy is employed to distribute the heated oil from solar
collectors among the above three systems considering the
temperature requirements. This modelling provides dynamic
performance results using measured meteorological data recorded
every minute at the solar facility location. The purpose of this
modeling approach is to accurately predict system performance at
each time step considering the solar radiation fluctuations due to
passing clouds. Optimization of the controller in cold temperatures is
another goal of the simulation to for example minimize heat losses in
winter when energy demand is high and solar resources are low.
The solar absorption cooling is modeled to use the generated heat
from the solar trough system and provide cooling in summer for a
greenhouse which is located next to the solar field.
The results of the simulation are presented for a summer day in
Winnipeg which includes comparison of performance parameters of
the absorption cooling and ORC systems at different heat transfer
fluid (HTF) temperatures.
Abstract: Applications of the Hausdorff space and its mappings
into tangent spaces are outlined, including their fractal dimensions
and self-similarities. The paper details this theory set up and further
describes virtualizations and atomization of manufacturing processes.
It demonstrates novel concurrency principles that will guide
manufacturing processes and resources configurations. Moreover,
varying levels of details may be produced by up folding and breaking
down of newly introduced generic models. This choice of layered
generic models for units and systems aspects along specific aspects
allows research work in parallel to other disciplines with the same
focus on all levels of detail. More credit and easier access are granted
to outside disciplines for enriching manufacturing grounds. Specific
mappings and the layers give hints for chances for interdisciplinary
outcomes and may highlight more details for interoperability
standards, as already worked on the international level. The new rules
are described, which require additional properties concerning all
involved entities for defining distributed decision cycles, again on the
base of self-similarity. All properties are further detailed and assigned
to a maturity scale, eventually displaying the smartness maturity of a
total shopfloor or a factory. The paper contributes to the intensive
ongoing discussion in the field of intelligent distributed
manufacturing and promotes solid concepts for implementations of
Cyber Physical Systems and the Internet of Things into
manufacturing industry, like industry 4.0, as discussed in German-speaking
countries.
Abstract: An innovative concept called “Flexy-Energy” is developing at 2iE. This concept aims to produce electricity at lower cost by smartly mix different available energy sources in accordance to the load profile of the region. With a higher solar irradiation and due to the fact that Diesel generator are massively used in sub-Saharan rural areas, PV/Diesel hybrid systems could be a good application of this concept and a good solution to electrify this region, provided they are reliable, cost effective and economically attractive to investors. Presentation of the developed approach is the aims of this paper. The PV/Diesel hybrid system designed consists to produce electricity and/or heat from a coupling between Diesel Diesel generators and PV panels without batteries storage, while ensuring the substitution of gasoil by bio-fuels available in the area where the system will be installed. The optimal design of this system is based on his technical performances; the Life Cycle Cost (LCC) and Levelized Cost of Energy are developed and use as economic criteria. The Net Present Value (NPV), the internal rate of return (IRR) and the discounted payback (DPB) are also evaluated according to dual electricity pricing (in sunny and unsunny hours). The PV/Diesel hybrid system obtained is compared to the standalone Diesel Diesel generators. The approach carried out in this paper has been applied to Siby village in Mali (Latitude 12 ° 23'N 8 ° 20'W) with 295 kWh as daily demand.This approach provides optimal physical characteristics (size of the components, number of component) and dynamical characteristics in real time (number of Diesel generator on, their load rate, fuel specific consumptions, and PV penetration rate) of the system. The system obtained is slightly cost effective; but could be improved with optimized tariffing strategies.
Abstract: This paper reports the worldwide status of building
information modeling (BIM) adoption from the perspectives of the
engagement level, the Hype Cycle model, the technology diffusion
model, and BIM services. An online survey was distributed, and 156
experts from six continents responded. Overall, North America was
the most advanced continent, followed by Oceania and Europe.
Countries in Asia perceived their phase mainly as slope of
enlightenment (mature) in the Hype Cycle model. In the technology
diffusion model, the main BIM-users worldwide were “early majority”
(third phase), but those in the Middle East/Africa and South America
were “early adopters” (second phase). In addition, the more advanced
the country, the more number of BIM services employed in general. In
summary, North America, Europe, Oceania, and Asia were advancing
rapidly toward the mature stage of BIM, whereas the Middle
East/Africa and South America were still in the early phase. The
simple indexes used in this study may be used to track the worldwide
status of BIM adoption in long-term surveys.
Abstract: This technical contribution treats of a novel approach
to condition-oriented maintenance as elaborated by Collaborative
Research Centre 653 at the Leibniz University in Hanover. The
objective resides in the targeted analysis of information about a
component's lifecycle for maintenance purposes. The information in
question is collected by means of the Collaborative Research Centre's
innovative technologies. This enables preventive maintenance of
components on the basis of their condition. This contribution initially
explains condition-oriented maintenance, before introducing the
Collaborative Research Centre and finally presenting the
methodology for analyzing the information. The current state of
development is described and an outlook provided for expanding the
methodology.
Abstract: Degradation of agricultural soils has increased rapidly
during the last 20 years due to the indiscriminate use of pesticides
and other anthropogenic activities. Currently, there is an urgent need
of soil restoration to increase agricultural production. Utilization of
sewage sludge or municipal solid waste is an important way to
recycle nutrient elements and improve soil quality. With these
amendments, nutrient availability in the aqueous phase might be
increased and production of healthier crops can be accomplished.
This research project aimed to achieve sustainable management of
tropical agricultural soils, specifically in Puerto Rico, through the
amendment of water treatment plant sludge’s. This practice avoids
landfill disposal of sewage sludge and at the same time results costeffective
practice for recycling solid waste residues. Coriander
sativum was cultivated in a compost-soil-sludge mixture at different
proportions. Results showed that Coriander grown in a mixture of
25% compost+50% Voladora soi+25% sludge had the best growth
and development. High chlorophyll content (33.01 ± 0.8) was
observed in Coriander plants cultivated in 25% compost+62.5%
Coloso soil+ 12.5% sludge compared to plants grown with no sludge
(32.59 ± 0.7). ICP-OES analysis showed variations in mineral
element contents (macro and micronutrients) in coriander plant
grown I soil amended with sludge and compost.
Abstract: The paper presents a thermodynamic cycle analysis
for three turboshaft engines. The first cycle is a Brayton cycle,
describing the evolution of a classical turboshaft, based on the
Klimov TV2 engine. The other four cycles aim at approaching an
Ericsson cycle, by replacing the Brayton cycle adiabatic expansion in
the turbine by quasi-isothermal expansion. The maximum quasi-
Ericsson cycles temperature is set to a lower value than the maximum
Brayton cycle temperature, equal to the Brayton cycle power turbine
inlet temperature, in order to decrease the engine NOx emissions.
Also, the power/expansion ratio distribution over the stages of the gas
generator turbine is maintained the same. In two of the considered
quasi-Ericsson cycles, the efficiencies of the gas generator turbine, as
well as the power/expansion ratio distribution over the stages of the
gas generator turbine are maintained the same as for the reference
case, while for the other two cases, the efficiencies are increased in
order to obtain the same shaft power as in the reference case. For the
two cases respecting the first condition, both the shaft power and the
thermodynamic efficiency of the engine decrease, while for the other
two, the power and efficiency are maintained, as a result of assuming
new, more efficient gas generator turbines.
Abstract: In this paper, we discuss the performance of applying
hybrid spiral dynamic bacterial chemotaxis (HSDBC) optimisation
algorithm on an intelligent controller for a differential drive robot. A
unicycle class of differential drive robot is utilised to serve as a basis
application to evaluate the performance of the HSDBC algorithm. A
hybrid fuzzy logic controller is developed and implemented for the
unicycle robot to follow a predefined trajectory. Trajectories of
various frictional profiles and levels were simulated to evaluate the
performance of the robot at different operating conditions. Controller
gains and scaling factors were optimised using HSDBC and the
performance is evaluated in comparison to previously adopted
optimisation algorithms. The HSDBC has proven its feasibility in
achieving a faster convergence toward the optimal gains and resulted
in a superior performance.
Abstract: Solid waste management in steel industry is broadly
classified in “4 Rs” i.e. reduce, reuse, recycle and restore the
materials. Reuse and recycling the entire solid waste generated in the
process of steel making is a viable solution in targeting a clean, green
and zero waste technology leading to sustainable development of the
steel industry. Solid waste management has gained importance in
steel industry in view of its uncertainty, volatility and speculation due
to world competitive standards, rising input costs, scarcity of raw
materials and solid waste generated like in other sectors. The
challenges that the steel Industry faces today are the requirement of a
sustainable development by meeting the needs of our present
generation without compromising the ability of future generations.
Technologies are developed not only for gainful utilization of solid
wastes in manufacture of conventional products but also for
conversion of same in to completely new products.
Abstract: Hurling a successful Construction and Demolition
Waste (C&DW) recycling operation around the globe is a challenge
today, predominantly because secondary materials markets are yet to
be integrated. Reducing, Reusing and recycling of (C&DW) have
been employed over the years, and various techniques have been
investigated. However, the economic and environmental viability of
its application seems limited. This paper discusses the costs and
benefits in using secondary materials and focus on investigating reuse
and recycling process for five major types of construction materials:
concrete, metal, wood, cardboard/paper and plasterboard. Data
obtained from demolition specialists and contractors are considered
and evaluated. The research paper found that construction material
recovery process fully incorporate a 3R’s principle contributing to
saving energy and natural resources. This scrutiny leads to the
empathy of grand challenges in construction material recovery
process. Recommendations to deepen material recovery process are
also discussed.
Abstract: Over the past four decades, the fatigue behavior of
nickel-based alloys has been widely studied. However, in recent
years, significant advances in the fabrication process leading to grain
size reduction have been made in order to improve fatigue properties
of aircraft turbine discs. Indeed, a change in particle size affects the
initiation mode of fatigue cracks as well as the fatigue life of the
material. The present study aims to investigate the fatigue behavior of
a newly developed nickel-based superalloy under biaxial-planar
loading. Low Cycle Fatigue (LCF) tests are performed at different
stress ratios so as to study the influence of the multiaxial stress state
on the fatigue life of the material. Full-field displacement and strain
measurements as well as crack initiation detection are obtained using
Digital Image Correlation (DIC) techniques. The aim of this
presentation is first to provide an in-depth description of both the
experimental set-up and protocol: the multiaxial testing machine, the
specific design of the cruciform specimen and performances of the
DIC code are introduced. Second, results for sixteen specimens
related to different load ratios are presented. Crack detection, strain
amplitude and number of cycles to crack initiation vs. triaxial stress
ratio for each loading case are given. Third, from fractographic
investigations by scanning electron microscopy it is found that the
mechanism of fatigue crack initiation does not depend on the triaxial
stress ratio and that most fatigue cracks initiate from subsurface
carbides.
Abstract: Previous studies on financial distress prediction choose
the conventional failing and non-failing dichotomy; however, the
distressed extent differs substantially among different financial
distress events. To solve the problem, “non-distressed”, “slightlydistressed”
and “reorganization and bankruptcy” are used in our article
to approximate the continuum of corporate financial health. This paper
explains different financial distress events using the two-stage method.
First, this investigation adopts firm-specific financial ratios, corporate
governance and market factors to measure the probability of various
financial distress events based on multinomial logit models.
Specifically, the bootstrapping simulation is performed to examine the
difference of estimated misclassifying cost (EMC). Second, this work
further applies macroeconomic factors to establish the credit cycle
index and determines the distressed cut-off indicator of the two-stage
models using such index. Two different models, one-stage and
two-stage prediction models are developed to forecast financial
distress, and the results acquired from different models are compared
with each other, and with the collected data. The findings show that the
one-stage model has the lower misclassification error rate than the
two-stage model. The one-stage model is more accurate than the
two-stage model.