Abstract: This paper proposes five level diode clamped Z source
Inverter. The existing PWM techniques used for ZSI are restricted for
two level. The two level Z Source Inverter have high harmonic
distortions which effects the performance of the grid connected PV
system. To improve the performance of the system the number of
voltage levels in the output waveform need to be increased. This
paper presents comparative analysis of a five level diode clamped Z
source Inverter with different carrier based Modified Pulse Width
Modulation techniques. The parameters considered for comparison
are output voltage, voltage gain, voltage stress across switch and total
harmonic distortion when powered by same DC supply. Analytical
results are verified using MATLAB.
Abstract: Most people today are aware that global climate
change is not just a scientific theory but also a fact with worldwide
consequences. Global climate change is due to rapid urbanization,
industrialization, high population growth and current vulnerability of
the climatic condition. Water is becoming scarce as a result of global
climate change. To mitigate the problem arising due to global climate
change and its drought effect, harvesting rainwater from green roofs,
an environmentally-friendly and versatile technology, is becoming
one of the best assessment criteria and gaining attention in Malaysia.
This paper addresses the sustainability of green roofs and examines
the quality of water harvested from green roofs in comparison to
rainwater. The factors that affect the quality of such water, taking
into account, for example, roofing materials, climatic conditions, the
frequency of rainfall frequency and the first flush. A green roof was
installed on the Humid Tropic Centre (HTC) is a place of the study
on monitoring program for urban Stormwater Management Manual
for Malaysia (MSMA), Eco-Hydrological Project in Kuala Lumpur,
and the rainwater was harvested and evaluated on the basis of four
parameters i.e., conductivity, dissolved oxygen (DO), pH and
temperature. These parameters were found to fall between Class I and
Class III of the Interim National Water Quality Standards (INWQS)
and the Water Quality Index (WQI). Some preliminary treatment
such as disinfection and filtration could likely to improve the value of
these parameters to class I. This review paper clearly indicates that
there is a need for more research to address other microbiological and
chemical quality parameters to ensure that the harvested water is
suitable for use potable water for domestic purposes. The change in
all physical, chemical and microbiological parameters with respect to
storage time will be a major focus of future studies in this field.
Abstract: Array-based gene expression analysis is a powerful
tool to profile expression of genes and to generate information on
therapeutic effects of new anti-cancer compounds. Anti-apoptotic
effect of thymoquinone was studied in MCF7 breast cancer cell line
using gene expression profiling with cDNA microarray. The purity
and yield of RNA samples were determined using RNeasyPlus Mini
kit. The Agilent RNA 6000 NanoLabChip kit evaluated the quantity
of the RNA samples. AffinityScript RT oligo-dT promoter primer
was used to generate cDNA strands. T7 RNA polymerase was used to
convert cDNA to cRNA. The cRNA samples and human universal
reference RNA were labelled with Cy-3-CTP and Cy-5-CTP,
respectively. Feature Extraction and GeneSpring softwares analysed
the data. The single experiment analysis revealed involvement of 64
pathways with up-regulated genes and 78 pathways with downregulated
genes. The MAPK and p38-MAPK pathways were
inhibited due to the up-regulation of PTPRR gene. The inhibition of
p38-MAPK suggested up-regulation of TGF-ß pathway. Inhibition of
p38-MAPK caused up-regulation of TP53 and down-regulation of
Bcl2 genes indicating involvement of intrinsic apoptotic pathway.
Down-regulation of CARD16 gene as an adaptor molecule regulated
CASP1 and suggested necrosis-like programmed cell death and
involvement of caspase in apoptosis. Furthermore, down-regulation
of GPCR, EGF-EGFR signalling pathways suggested reduction of
ER. Involvement of AhR pathway which control cytochrome P450
and glucuronidation pathways showed metabolism of Thymoquinone.
The findings showed differential expression of several genes in
apoptosis pathways with thymoquinone treatment in estrogen
receptor-positive breast cancer cells.
Abstract: The check-in area of airport terminal is one of the
busiest sections at airports at certain periods. The passengers are
subjected to queues and delays during the check-in process. These
delays and queues are due to constraints in the capacity of service
facilities. In this project, the airport terminal is decomposed into
several check-in areas. The airport check-in scheduling problem
requires both a deterministic (integer programming) and stochastic
(simulation) approach. Integer programming formulations are
provided to minimize the total number of counters in each check-in
area under the realistic constraint that counters for one and the same
flight should be adjacent and the desired number of counters
remaining in each area should be fixed during check-in operations.
By using simulation, the airport system can be modeled to study the
effects of various parameters such as number of passengers on a
flight and check-in counter opening and closing time.
Abstract: In the past few decades, the field of chemistry
education has grown tremendously and researches indicated that after
traditional chemistry instruction students often lacked deep
conceptual understanding and failed to integrate their ideas into
coherent conceptual framework. For several concepts in chemistry,
students at all levels have demonstrated difficulty in changing their
initial perceptions. Their perceptions are most often wrong and don't
agree with correct scientific concepts. This study explored the
effectiveness of intervention discussion sections for a college general
chemistry course designed to apply research on students
preconceptions, knowledge integration and student explanation.
Three interventions discussions lasting three hours on bond energy
and spontaneity were done tested and intervention (treatment)
students’ performances were compared with that of control group
which did not use the experimental pedagogy. Results indicated that
this instruction which was capable of identifying students'
misconceptions, initial conceptions and integrating those ideas into
class discussion led to enhanced conceptual understanding and better
achievement for the experimental group.
Abstract: The main aim of the presented experiments is to
improve behaviour of sandwich structures under dynamic loading,
such as crash or explosion. This paper describes experimental
investigation on the response of new advanced materials to low and
high velocity load. Blast wave energy absorbers were designed using
two types of porous lightweight raw particle materials based on
expanded glass and ceramics with dimensions of 0.5-1 mm,
combined with polymeric binder. The effect of binder amount on the
static and dynamic properties of designed materials was observed.
Prism shaped specimens were prepared and loaded to obtain physicomechanical
parameters – bulk density, compressive and flexural
strength under quasistatic load, the dynamic response was determined
using Split Hopkinson Pressure bar apparatus. Numerical
investigation of the material behaviour in sandwich structure was
performed using implicit/explicit solver LS-Dyna. As the last step,
the developed material was used as the interlayer of blast resistant
litter bin, and it´s functionality was verified by real field blast tests.
Abstract: In this paper we consider the equation of motion for
the F (R, T) gravity on their property of conformal invariance. It
is shown that in the general case, such a theory is not conformal
invariant. Studied special cases for the functions v and u in which
can appear properties of the theory. Also we consider cosmological
aspects F (R, T) theory of gravity, having considered particular case
F (R, T) = μR+νT^2. Showed that in this case there is a nonlinear
dependence of the parameter equation of state from time to time,
which affects its evolution.
Abstract: Using the pseudopotential technique the Sagdeev
potential equation has been derived in a plasma consisting of twotemperature
nonisothermal electrons, negatively charged dust grains
and warm positive ions. The study shows that the presence of
nonisothermal two-temperature electrons and charged dust grains
have significant effects on the excitation and structure of the ionacoustic
double layers in the model plasma under consideration. Only
compressive type double layer is obtained in the present plasma
model. The double layer solution has also been obtained by including
higher order nonlinearity and nonisothermality, which is shown to
modify the amplitude and deform the shape of the double layer.
Abstract: Now in some countries of the world the cellular
market is on the point of saturation, in others - positive dynamics of
development kept on. The reasons for it are also different, but there
are united by their general susceptibility to innovation changes, if
they are really innovative. If to take as an example the cellular market
of Kazakhstan it is defined by the low percent of smart phones at
consumers, the low population density, undercapacity of the 3G
channel, and absence of universal access to the LTE technology that
limits dynamical growth of this branch. These moments are
aggravated by failures of starting commercial projects by private
companies which prevent to be implemented and widely adopted to a
new product among consumers. The object of the research is possible
integration of wireless and program technologies at which
introduction the idea can regenerate in an innovation. The analysis of
existing projects in the market and the possible union of the
technologies through a prism of theoretical bases of innovative
activity shows that efficiency of the company by development and
introduction of innovations is possible only thanks to strict
observance of all terms and conditions of the innovative process
which main term is profit. Despite that fact that on a global scale the
innovativeness issue of companies is very popular, there are no
researches about possibility of innovative breaks in the field of
wireless access to the Internet in the cellular market of Kazakhstan.
Abstract: Exact solution of an unsteady flow of elastico-viscous
fluid through a porous media in a tube of ellipsoidal cross section
under the influence of constant pressure gradient has been obtained in
this paper. Initially, the flow is generated by a constant pressure
gradient. After attaining the steady state, the pressure gradient is
suddenly withdrawn and the resulting fluid motion in a tube of
ellipsoidal cross section by taking into account of the porosity factor
of the bounding surface is investigated. The problem is solved in twostages
the first stage is a steady motion in tube under the influence of
a constant pressure gradient, the second stage concern with an
unsteady motion. The problem is solved employing separation of
variables technique. The results are expressed in terms of a nondimensional
porosity parameter (K) and elastico-viscosity parameter
(β), which depends on the Non-Newtonian coefficient. The flow
parameters are found to be identical with that of Newtonian case as
elastic-viscosity parameter tends to zero and porosity tends to
infinity. It is seen that the effect of elastico-viscosity parameter and
the porosity parameter of the bounding surface has significant effect
on the velocity parameter.
Abstract: This study aimed to identify the alignment of
understanding and assessment practices among secondary school
teachers. The study was carried out using quantitative descriptive
study. The sample consisted of 164 teachers who taught Form 1 and 2
from 11 secondary schools in the district of North Kinta, Perak,
Malaysia. Data were obtained from 164 respondents who answered
Expectation Alignment Understanding and Practices of School
Assessment (PEKDAPS) questionnaire. The data were analysed
using SPSS 17.0+. The Cronbach’s alpha value obtained through
PEKDAPS questionnaire pilot study was 0.86. The results showed
that teachers' performance in PEKDAPS based on the mean value
was less than 3, which means that perfect alignment does not occur
between the understanding and practices of school assessment. Two
major PEKDAPS sub-constructs of articulation across grade and age
and usability of the system were higher than the moderate alignment
of the understanding and practices of school assessment (Min=2.0).
The content focused of PEKDAPs sub-constructs which showed
lower than the moderate alignment of the understanding and practices
of school assessment (Min=2.0). Another two PEKDAPS subconstructs
of transparency and fairness and the pedagogical
implications showed moderate alignment (2.0). The implications of
the study is that teachers need to fully understand the importance of
alignment among components of assessment, learning and teaching
and learning objectives as strategies to achieve quality assessment
process.
Abstract: The dissimilar joint between aluminum/titanium
alloys (Al 6082 and Ti G2) were successfully achieved by CO2 laser
welding with a single pass and without filler material using the
overlap joint design. Laser welding parameters ranges combinations
were experimentally determined using Taguchi approach with the
objective of producing welded joint with acceptable welding profile
and high quality of mechanical properties. In this study a joining of
dissimilar Al 6082 / Ti G2 was resulted in three distinct regions
fusion area in the weldment. These regions are studied in terms of its
microstructural characteristics and microhardness which are directly
affecting the welding quality.
The weld metal was mainly composed of martensite alpha prime.
In two different metals in the two different sides of joint HAZ, grain
growth was detected. The microhardness of the joint distribution also
has shown microhardness increasing in the HAZ of two base metals
and a varying microhardness in fusion zone.
Abstract: Over the years, it has been extensively established that
the practice of assuming a structure being fixed at base, leads to gross
errors in evaluation of its overall response due to dynamic loadings
and overestimations in design. The extent of these errors depends on
a number of variables; soil type being one of the major factor. This
paper studies the effect of Soil Structure Interaction (SSI) on multistorey
buildings with varying under-laying soil types after proper
validation of the effect of SSI. Analysis for soft, stiff and very stiff
base soils has been carried out, using a powerful Finite Element
Method (FEM) software package ANSYS v14.5. Results lead to
some very important conclusions regarding time period, deflection
and acceleration responses.
Abstract: Semiconductor crystals smaller than about 10 nm,
known as quantum dots, have properties that differ from large
samples, including a band gap that becomes larger for smaller
particles. These properties create several applications for quantum
dots. In this paper new shapes of quantum dot arrays are used to
enhance the photo physical properties of gold nano-particles. This
paper presents a study of the effect of nano-particles shape, array, and
size on their absorption characteristics.
Abstract: We are facing serious problems related to long-term
depopulation and an aging society with a falling birth rate in Japan. In
this situation, we are suffering from a shortfall in human resources as
well as a shortage of workforce in rural regions. In addition, we are
struggling with a protracted economic slump and excess concentration
of population in the Tokyo Metropolitan area. It is an urgent national
issue to consider how to live in this country and what kind of structure
of society and administration policy is needed. It is necessary to clarify
people’s desire for their way of living and social assistance to be
provided. The aim of this study is to clarify the characteristics of
regional issues and the degree of their seriousness in local
municipalities of Japan. We conducted a questionnaire survey about
regional agenda in all local municipalities in Japan. We obtained
responses concerning the degree of seriousness of regional issues and
degree of importance of policies. Based on the data gathered from the
survey, it is apparent that many local municipalities are facing an
aging population and declining population. We constructed a model to
analyze factors for declining population. Using the model, it was
clarified that a population’s age structure, job opportunities and
income level affect the decline of population. In addition, we showed
the way of the evaluation of state of local municipality.
Abstract: The building sector is responsible, in many
industrialized countries, for about 40% of the total energy
requirements, so it seems necessary to devote some efforts in this
area in order to achieve a significant reduction of energy
consumption and of greenhouse gases emissions.
The paper presents a study aiming at providing a design
methodology able to identify the best configuration of the system
building/plant, from a technical, economic and environmentally point
of view.
Normally, the classical approach involves a building's energy
loads analysis under steady state conditions, and subsequent selection
of measures aimed at improving the energy performance, based on
previous experience made by architects and engineers in the design
team. Instead, the proposed approach uses a sequence of two wellknown
scientifically validated calculation methods (TRNSYS and
RETScreen), that allow quite a detailed feasibility analysis.
To assess the validity of the calculation model, an existing,
historical building in Central Italy, that will be the object of
restoration and preservative redevelopment, was selected as a casestudy.
The building is made of a basement and three floors, with a
total floor area of about 3,000 square meters.
The first step has been the determination of the heating and
cooling energy loads of the building in a dynamic regime by means,
which allows simulating the real energy needs of the building in
function of its use. Traditional methodologies, based as they are on
steady-state conditions, cannot faithfully reproduce the effects of
varying climatic conditions and of inertial properties of the structure.
With this model is possible to obtain quite accurate and reliable
results that allow identifying effective combinations building-HVAC
system.
The second step has consisted of using output data obtained as
input to the calculation model, which enables to compare different
system configurations from the energy, environmental and financial
point of view, with an analysis of investment, and operation and
maintenance costs, so allowing determining the economic benefit of
possible interventions.
The classical methodology often leads to the choice of
conventional plant systems, while our calculation model provides a
financial-economic assessment for innovative energy systems and
low environmental impact.
Computational analysis can help in the design phase, particularly
in the case of complex structures with centralized plant systems, by
comparing the data returned by the calculation model for different
design options.
Abstract: Comparing other methods of waste water treatment,
constructed wetlands are one of the most fascinating practices
because being a natural process they are eco-friendly have low
construction and maintenance cost and have considerable capability
of wastewater treatment. The current research was focused mainly on
comparison of Ranunculus muricatus and Typha latifolia as wetland
plants for domestic wastewater treatment by designing and
constructing efficient pilot scale horizontal subsurface flow
mesocosms. Parameters like chemical oxygen demand, biological
oxygen demand, phosphates, sulphates, nitrites, nitrates, and
pathogenic indicator microbes were studied continuously with
successive treatments. Treatment efficiency of the system increases
with passage of time and with increase in temperature. Efficiency of
T. latifolia planted setups in open environment was fairly good for
parameters like COD and BOD5 which was showing reduction up to
82.5% for COD and 82.6% for BOD5 while DO was increased up to
125%. Efficiency of R. muricatus vegetated setup was also good but
lowers than that of T. latifolia planted showing 80.95% removal of
COD and BOD5. Ranunculus muricatus was found effective in
reducing bacterial count in wastewater. Both macrophytes were
found promising in wastewater treatment.
Abstract: Cemented carbide balls are usually implemented in
industry under the environment of high speed, high temperature,
corrosiveness and strong collisions. However, its application is limited
due to high fabrication cost, processing efficiency and quality. A novel
eccentric lapping method with two rotatable lapping plates was
proposed in this paper. A mathematical model was constructed to
analyze the influence of each design parameter on this lapping method.
To validate this new lapping method, an orthogonal experiment was
conducted with cemented carbide balls (YG6). The simulation model
was verified and the optimal lapping parameters were derived. The
results show that the surface roundness of the balls reaches to 0.65um
from 2um in 1 hour using this lapping method. So, using this novel
lapping method, it can effectively improve the machining precision
and efficiency of cemented carbide balls.
Abstract: New physical insights into the nonlinear Lorenz
equations related to flow resistance is discussed in this work. The
chaotic dynamics related to Lorenz equations has been studied in
many papers, which is due to the sensitivity of Lorenz equations to
initial conditions and parameter uncertainties. However, the physical
implication arising from Lorenz equations about convectional motion
attracts little attention in the relevant literature. Therefore, as a first
step to understand the related fluid mechanics of convectional motion,
this paper derives the Lorenz equations again with different forced
conditions in the model. Simulation work of the modified Lorenz
equations without the viscosity or buoyancy force is discussed. The
time-domain simulation results may imply that the states of the
Lorenz equations are related to certain flow speed and flow resistance.
The flow speed of the underlying fluid system increases as the flow
resistance reduces. This observation would be helpful to analyze the
coupling effects of different fluid parameters in a convectional model
in future work.
Abstract: Thin-walled elements with a matrix set on a base of
high-valuable Portland cement with dispersed reinforcement from
alkali-resistant glass fibres are used in a range of applications as
claddings of buildings and infrastructure constructions as well as
various architectural elements of residential buildings.
Even though their elementary thickness and therefore total weight
is quite low, architects and building companies demand on even
further decreasing of the bulk density of these fibre-cement elements
for the reason of loading elimination of connected superstructures
and easier assembling in demand conditions.
By the means of various kinds of light-weight aggregates it is
possible to achieve light-weighing of these composite elements.
From the range of possible fillers with different material properties
granulated expanded glass worked the best.
By the means of laboratory testing an effect of two fillers based on
expanded glass on the fibre reinforced cement composite was
verified.
Practical applicability was tested in the production of commonly
manufactured glass fibre reinforced concrete elements, such as
channels for electrical cable deposition, products for urban equipment
and especially various cladding elements.
Even though these are not structural elements, it is necessary to
evaluate also strength characteristics and resistance to environment
for their durability in certain applications.