Abstract: Motion capturing technology has been used for quite a
while and several research has been done within this area. Nevertheless,
we discovered open issues within current motion capturing
environments. In this paper we provide a state-of-the-art overview of
the addressed research areas and show issues with current motion
capturing environments. Observations, interviews and questionnaires
have been used to reveal the challenges actors are currently facing in
a motion capturing environment. Furthermore, the idea to create a
more immersive motion capturing environment to improve the acting
performances and motion capturing outcomes as a potential solution
is introduced. It is hereby the goal to explain the found open issues
and the developed ideas which shall serve for further research as a
basis. Moreover, a methodology to address the interaction and
systems design issues is proposed. A future outcome could be that
motion capture actors are able to perform more naturally, especially
if using a non-body-worn solution.
Abstract: This paper describes a practical approach to design
and develop a hybrid learning with acceleration feedback control
(HLC) scheme for input tracking and end-point vibration suppression
of flexible manipulator systems. Initially, a collocated proportionalderivative
(PD) control scheme using hub-angle and hub-velocity
feedback is developed for control of rigid-body motion of the system.
This is then extended to incorporate a further hybrid control scheme
of the collocated PD control and iterative learning control with
acceleration feedback using genetic algorithms (GAs) to optimize the
learning parameters. Experimental results of the response of the
manipulator with the control schemes are presented in the time and
frequency domains. The performance of the HLC is assessed in terms
of input tracking, level of vibration reduction at resonance modes and
robustness with various payloads.
Abstract: The present paper deals with the analysis and development of noise-reduction transformer that has a filter function for conductive noise transmission. Two types of prototype noise-reduction transformers with two different output voltages are proposed. To determine an optimum design for the noise-reduction transformer, noise attenuation characteristics are discussed based on the experiments and the equivalent circuit analysis. The analysis gives a relation between the circuit parameters and the noise attenuation. High performance step-down noise-reduction transformer for direct power supply to electronics equipment is developed. The input voltage of the transformer is 100 V and the output voltage is 5 V. Frequency characteristics of noise attenuation are discussed, and prevention of pulse noise transmission is demonstrated. Normal mode noise attenuation of this transformer is –80 dB, and common mode exceeds –90 dB. The step-down noise-reduction transformer eliminates pulse noise efficiently.
Abstract: Facial recognition and expression analysis is rapidly
becoming an area of intense interest in computer science and humancomputer
interaction design communities. The most expressive way
humans display emotions is through facial expressions. In this paper
skin and non-skin pixels were separated. Face regions were extracted
from the detected skin regions. Facial expressions are analyzed from
facial images by applying Gabor wavelet transform (GWT) and
Discrete Cosine Transform (DCT) on face images. Radial Basis
Function (RBF) Network is used to identify the person and to classify
the facial expressions. Our method reliably works even with faces,
which carry heavy expressions.
Abstract: In this document, we have proposed a robust
conceptual strategy, in order to improve the robustness against the manufacturing defects and thus the reliability of logic CMOS circuits. However, in order to enable the use of future CMOS
technology nodes this strategy combines various types of design:
DFR (Design for Reliability), techniques of tolerance: hardware
redundancy TMR (Triple Modular Redundancy) for hard error
tolerance, the DFT (Design for Testability. The Results on largest ISCAS and ITC benchmark circuits show that our approach improves
considerably the reliability, by reducing the key factors, the area costs and fault tolerance probability.
Abstract: The impact of OO design on software quality
characteristics such as defect density and rework by mean of
experimental validation. Encapsulation, inheritance, polymorphism,
reusability, Data hiding and message-passing are the major attribute
of an Object Oriented system. In order to evaluate the quality of an
Object oriented system the above said attributes can act as indicators.
The metrics are the well known quantifiable approach to express any
attribute. Hence, in this paper we tried to formulate a framework of
metrics representing the attributes of object oriented system.
Empirical Data is collected from three different projects based on
object oriented paradigms to calculate the metrics.
Abstract: Computer aided design accounts with the support of
parametric software in the design of machine components as well as
of any other pieces of interest. The complexities of the element under
study sometimes offer certain difficulties to computer design, or ever
might generate mistakes in the final body conception. Reverse
engineering techniques are based on the transformation of already
conceived body images into a matrix of points which can be
visualized by the design software. The literature exhibits several
techniques to obtain machine components dimensional fields, as
contact instrument (MMC), calipers and optical methods as laser
scanner, holograms as well as moiré methods. The objective of this
research work was to analyze the moiré technique as instrument of
reverse engineering, applied to bodies of nom complex geometry as
simple solid figures, creating matrices of points. These matrices were
forwarded to a parametric software named SolidWorks to generate
the virtual object. Volume data obtained by mechanical means, i.e.,
by caliper, the volume obtained through the moiré method and the
volume generated by the SolidWorks software were compared and
found to be in close agreement. This research work suggests the
application of phase shifting moiré methods as instrument of reverse
engineering, serving also to support farm machinery element designs.
Abstract: The seismic rehabilitation designs of two reinforced
concrete school buildings, representative of a wide stock of similar
edifices designed under earlier editions of the Italian Technical
Standards, are presented in this paper. The mutual retrofit solution
elaborated for the two buildings consists in the incorporation of a
dissipative bracing system including pressurized fluid viscous springdampers
as passive protective devices. The mechanical parameters,
layouts and locations selected for the constituting elements of the
system; the architectural renovation projects developed to properly
incorporate the structural interventions and improve the appearance
of the buildings; highlights of the installation works already
completed in one of the two structures; and a synthesis of the
performance assessment analyses carried out in original and
rehabilitated conditions, are illustrated. The results of the analyses
show a remarkable enhancement of the seismic response capacities of
both structures. This allows reaching the high performance objectives
postulated in the retrofit designs with much lower costs and
architectural intrusion as compared to traditional rehabilitation
interventions designed for the same objectives.
Abstract: Flat double-layer grid is from category of space structures that are formed from two flat layers connected together with diagonal members. Increased stiffness and better seismic resistance in relation to other space structures are advantages of flat double layer space structures. The objective of this study is assessment and calculation of Behavior factor of flat double layer space structures. With regarding that these structures are used widely but Behavior factor used to design these structures against seismic force is not determined and exact, the necessity of study is obvious. This study is theoretical. In this study we used structures with span length of 16m and 20 m. All connections are pivotal. ANSYS software is used to non-linear analysis of structures.
Abstract: This paper describes the NEAR (Navigating Exhibitions, Annotations and Resources) panel, a novel interactive visualization technique designed to help people navigate and interpret groups of resources, exhibitions and annotations by revealing hidden relations such as similarities and references. NEAR is implemented on A•VI•RE, an extended online information repository. A•VI•RE supports a semi-structured collection of exhibitions containing various resources and annotations. Users are encouraged to contribute, share, annotate and interpret resources in the system by building their own exhibitions and annotations. However, it is hard to navigate smoothly and efficiently in A•VI•RE because of its high capacity and complexity. We present a visual panel that implements new navigation and communication approaches that support discovery of implied relations. By quickly scanning and interacting with NEAR, users can see not only implied relations but also potential connections among different data elements. NEAR was tested by several users in the A•VI•RE system and shown to be a supportive navigation tool. In the paper, we further analyze the design, report the evaluation and consider its usage in other applications.
Abstract: Flood management is one of the important fields in
urban storm water management. Floods are influenced by the
increase of huge storm event, or improper planning of the area. This study mainly provides the flood protection in four stages; planning,
flood event, responses and evaluation. However it is most effective then flood protection is considered in planning/design and
evaluation stages since both stages represent the land development of the area. Structural adjustments are often more reliable than nonstructural
adjustments in providing flood protection, however
structural adjustments are constrained by numerous factors such as
political constraints and cost. Therefore it is important to balance
both adjustments with the situation. The technical decisions provided
will have to be approved by the higher-ups who have the power to
decide on the final solution. Costs however, are the biggest factor in
determining the final decision. Therefore this study recommends
flood protection system should have been integrated and enforces
more in the early stages (planning and design) as part of the storm
water management plan. Factors influencing the technical decisions
provided should be reduced as low as possible to avoid a reduction in
the expected performance of the proposed adjustments.
Abstract: Numerical analysis naturally finds applications in all
fields of engineering and the physical sciences, but in the
21st century, the life sciences and even the arts have adopted
elements of scientific computations. The numerical data analysis
became key process in research and development of all the fields [6].
In this paper we have made an attempt to analyze the specified
numerical patterns with reference to the association rule mining
techniques with minimum confidence and minimum support mining
criteria. The extracted rules and analyzed results are graphically
demonstrated. Association rules are a simple but very useful form of
data mining that describe the probabilistic co-occurrence of certain
events within a database [7]. They were originally designed to
analyze market-basket data, in which the likelihood of items being
purchased together within the same transactions are analyzed.
Abstract: It is hard to express emotion through only speech when
we watch a character in a movie or a play because we cannot estimate
the size, kind, and quantity of emotion. So this paper proposes an
artificial emotion model for visualizing current emotion with color and
location in emotion model. The artificial emotion model is designed
considering causality of generated emotion, difference of personality,
difference of continual emotional stimulus, and co-relation of various
emotions. This paper supposed the Emotion Field for visualizing
current emotion with location, and current emotion is expressed by
location and color in the Emotion Field. For visualizing changes
within current emotion, the artificial emotion model is adjusted to
characters in Hamlet.
Abstract: The electromagnetic spectrum is a natural resource
and hence well-organized usage of the limited natural resources is the
necessities for better communication. The present static frequency
allocation schemes cannot accommodate demands of the rapidly
increasing number of higher data rate services. Therefore, dynamic
usage of the spectrum must be distinguished from the static usage to
increase the availability of frequency spectrum. Cognitive radio is not
a single piece of apparatus but it is a technology that can incorporate
components spread across a network. It offers great promise for
improving system efficiency, spectrum utilization, more effective
applications, reduction in interference and reduced complexity of
usage for users. Cognitive radio is aware of its environmental,
internal state, and location, and autonomously adjusts its operations
to achieve designed objectives. It first senses its spectral environment
over a wide frequency band, and then adapts the parameters to
maximize spectrum efficiency with high performance. This paper
only focuses on the analysis of Bit-Error-Rate in cognitive radio by
using Particle Swarm Optimization Algorithm. It is theoretically as
well as practically analyzed and interpreted in the sense of
advantages and drawbacks and how BER affects the efficiency and
performance of the communication system.
Abstract: One challenging direction of mobile commerce (mcommerce)
that is getting a great deal of attention globally is mobile
financing. The smart-phone and PDA users all around the world are
facing difficulties to become accustomed and trust in m-commerce.
The main rationale can be the slow variation and lack of trust in
mobile payment systems. Mobile payment systems that are in use
need to be more effective and efficient. This paper proposes: the
interface design is not the only factor affecting the m-commerce
adoption and lack of trust; in fact it is the combined effect of
interface usability and trustworthy mobile payment systems, because
it-s the money that the user has to spend at the end of the day, which
the user requires to get transferred securely. The purpose of this
research is to identify the problems regarding the trust and adaption
of m-commerce applications by mobile users and to provide the best
possible solution with respect to human computer interaction (HCI)
principles.
Abstract: In this research, Response Surface Methodology (RSM) is used to investigate the effect of four controllable input variables namely: discharge current, pulse duration, pulse off time and applied voltage Surface Roughness (SR) of on Electrical Discharge Machined surface. To study the proposed second-order polynomial model for SR, a Central Composite Design (CCD) is used to estimation the model coefficients of the four input factors, which are alleged to influence the SR in Electrical Discharge Machining (EDM) process. Experiments were conducted on AISI D2 tool steel with copper electrode. The response is modeled using RSM on experimental data. The significant coefficients are obtained by performing Analysis of Variance (ANOVA) at 5% level of significance. It is found that discharge current, pulse duration, and pulse off time and few of their interactions have significant effect on the SR. The model sufficiency is very satisfactory as the Coefficient of Determination (R2) is found to be 91.7% and adjusted R2-statistic (R2 adj ) 89.6%.
Abstract: The psychological and physical trauma associated with the loss of a human limb can severely impact on the quality of life of an amputee rendering even the most basic of tasks very difficult. A prosthetic device can be of great benefit to the amputee in the performance of everyday human tasks. This paper outlines a proposed mechanical design of a 12 degree-of-freedom SMA actuated artificial hand. It is proposed that the SMA wires be embedded intrinsically within the hand structure which will allow for significant flexibility for use either as a prosthetic hand solution, or as part of a complete lower arm prosthetic solution. A modular approach is taken in the design facilitating ease of manufacture and assembly, and more importantly, also allows the end user to easily replace SMA wires in the event of failure. A biomimetric approach has been taken during the design process meaning that the artificial hand should replicate that of a human hand as far as is possible with due regard to functional requirements. The proposed design has been exposed to appropriate loading through the use of finite element analysis (FEA) to ensure that it is structurally sound. Theoretical analysis of the mechanical framework was also carried out to establish the limits of the angular displacement and velocity of the finger tip as well finger tip force generation. A combination of various polymers and Titanium, which are suitably lightweight, are proposed for the manufacture of the design.
Abstract: This research proposes an Interactive 3D Experience to
enhance customer value in the fantasy era. As products reach maturity,
they become more similar in the range of functions that they provide.
This leads to competition via reduced retail price and ultimately
reduced profitability. A competitive design method is therefore
needed that can produce higher value products. An Enhanced Value
Experience has been identified that can assist designers to provide
quality products and to give them a unique positioning. On the basis of
this value opportunity, the method of Interactive 3D Experience has
been formulated and applied to the domain of retail furniture. Through
this, customers can create their own personalized styling via the
interactive 3D platform.
Abstract: An information procuring and processing emerging technology wireless sensor network (WSN) Consists of autonomous nodes with versatile devices underpinned by applications. Nodes are equipped with different capabilities such as sensing, computing, actuation and wireless communications etc. based on application requirements. A WSN application ranges from military implementation in the battlefield, environmental monitoring, health sector as well as emergency response of surveillance. The nodes are deployed independently to cooperatively monitor the physical and environmental conditions. The architecture of WSN differs based on the application requirements and focus on low cost, flexibility, fault tolerance capability, deployment process as well as conserve energy. In this paper we have present the characteristics, architecture design objective and architecture of WSN
Abstract: Machine Translation, (hereafter in this document
referred to as the "MT") faces a lot of complex problems from its
origination. Extracting multiword expressions is also one of the
complex problems in MT. Finding multiword expressions during
translating a sentence from English into Urdu, through existing
solutions, takes a lot of time and occupies system resources. We have
designed a simple relational data approach, in which we simply set a
bit in dictionary (database) for multiword, to find and handle
multiword expression. This approach handles multiword efficiently.