Abstract: The number of persons with implanted cardiac
pacemakers (PM) has increased in Western countries. The aim of this
paper is to investigate the possible situations where persons with a
PM may be exposed to extremely low frequency (ELF) electric (EF)
and magnetic fields (MF) that may disturb their PM. Based on our
earlier studies, it is possible to find such high public exposure to EFs
only in some places near 400 kV power lines, where an EF may
disturb a PM in unipolar mode. Such EFs cannot be found near 110
kV power lines. Disturbing MFs can be found near welding
machines. However, we do not have measurement data from welding.
Based on literature and earlier studies at Tampere University of
Technology, it is difficult to find public EF or MF exposure that is
high enough to interfere with PMs.
Abstract: In 2010-2011, the research on zooplankton was
conducted in the southern part of the Baltic Sea to determine seasonal
variability in changes occurring throughout the zooplankton in 2010
and 2011, both in the region of Gdańsk Deep, and in the western part
of Gdańsk Bay. The research in the sea showed that the taxonomic
composition of holoplankton in the southern part of the Baltic Sea
was similar to that recorded in this region for many years. The
maximum values of abundance and biomass of zooplankton both in
the Deep and the Bay of Gdańsk were observed in the summer
season. Copepoda dominated in the composition of zooplankton for
almost the entire study period, while rotifers occurred in larger
numbers only in the summer 2010 in the Gdańsk Deep as well as in
May and July 2010 in the western part of Gdańsk Bay, and
meroplankton – in April 2011.
Abstract: The performance of box-type solar cookers has been
reported by several researchers but little attention was paid to the
effect of the type of insulation material on the energy and exergy
efficiency of these cookers. This research aimed at evaluating the
energy and exergy efficiencies of the box-type cookers containing
different insulation materials. Energy and exergy efficiencies of five
box-type solar cookers insulated with maize cob, air (control), maize
husk, coconut coir and polyurethane foam respectively were obtained
over a period of three years. The cookers were evaluated using water
heating test procedures in determining the energy and exergy
analysis. The results were subjected to statistical analysis using
ANOVA. The result shows that the average energy input for the five
solar cookers were: 245.5, 252.2, 248.7, 241.5 and 245.5J
respectively while their respective average energy losses were: 201.2,
212.7, 208.4, 189.1 and 199.8J. The average exergy input for five
cookers were: 228.2, 234.4, 231.1, 224.4 and 228.2J respectively
while their respective average exergy losses were: 223.4, 230.6,
226.9, 218.9 and 223.0J. The energy and exergy efficiency was
highest in the cooker with coconut coir (37.35 and 3.90%
respectively) in the first year but was lowest for air (11 and 1.07%
respectively) in the third year. Statistical analysis showed significant
difference between the energy and exergy efficiencies over the years.
These results reiterate the importance of a good insulating material
for a box-type solar cooker.
Abstract: We present a framework of researcher knowledge
development in conducting a study in mathematics education. The
key components of the framework are: knowledge germane to
conducting a particular study, processes of knowledge accumulation,
and catalyzing filters that influence a researcher decision making.
The components of the framework originated from a confluence
between constructs and theories in Mathematics Education, Higher
Education and Sociology. Drawing on a self-reflective interview with
a leading researcher in mathematics education, Professor Michèle
Artigue, we illustrate how the framework can be utilized in data
analysis. Criteria for framework evaluation are discussed.
Abstract: Feed oil samples which are used as mixed feed raw
material were taken from six different feed factories in March, May
and July. All factories make production in Konya, Turkey and all of
the samples were crude soybean oils. Physical and chemical analyses,
free radical scavenger effect, and total phenol content were
determined on these oil samples. Moisture (M) content was found
between 0.10-22.23%, saponification number (SF) was determined
143.13 to 167.93 KOH/kg, free fatty acidity (FFA) was varied 0.73 to
35.00%, peroxide value (PV) was found between 1.53 and 28.43
meq/kg, unsaponifiable matter (USM) was determined from 0.40 to
17.10%, viscosity (V) was found between 34.30 and 625.67 mPas,
sediment (S) amount was determined between 0.60-18.16%, free
radical scavenger effect (FRSE) was varied 20.7 to 43.04% inhibition
of the extract and total phenol (TPC) content was found between 1.20
and 2.69mg/L extract. Different results were found between months
and factories.
Abstract: Forward Osmosis (FO) polyamide thin-film composite
membranes have been prepared by interfacial polymerization using
commercial UF polyethersulfoneas membrane support. Different
interfacial polymerization times (10s, 30s and 60s) in the organic
solution containing trimesoyl chloride (TMC) at constant m-phenylenediamine
(MPD) concentration (2% w/v) were studied. The
synthesized polyamide membranes then tested for treatment of
natural organic matter (NOM) and compared to commercial Cellulose
TriAcetate (CTA) membrane. It was found that membrane prepared
with higher reaction time (30s and 60s) exhibited better membrane
performance (flux and humic acid removal) over commercial CTA
membrane.
Abstract: Verification of vented wooden façade system with
bonded joints is presented in this paper. The potential of bonded
joints is studied and described in more detail. The paper presents the results of an experimental and theoretical research about the effects of freeze cycling on the bonded joint. For the purpose of tests spruce
timber profiles were chosen for the load bearing substructure. Planks from wooden plastic composite and Siberian larch are representing facade cladding. Two types of industrial polyurethane adhesives intended for structural bonding were selected. The article is focused on the preparation as well as on the subsequent curing and conditioning of test samples. All test samples were subjected to 15 cycles that represents sudden temperature changes, i.e. immersion in a water bath at (293.15 ± 3) K for 6 hours and subsequent freezing to (253.15 ± 2) K for 18 hours. Furthermore, the retention of bond strength between substructure and cladding wastested and strength in shear was determined under tensile stress.Research data indicate that little, if any, damage to the bond results from freezingcycles. Additionally, the suitability of selected group of adhesives in combination with timber substructure was confirmed.
Abstract: Dental porcelain composites reinforced and toughened
by 20 wt.% tetragonal zirconia (3Y-TZP) were processed by hot
pressing at 1000°C. Two types of particles were tested: yttriastabilized
zirconia (ZrO2–3%Y2O3) agglomerates and pre-sintered
yttria-stabilized zirconia (ZrO2–3%Y2O3) particles. The composites
as well as the reinforcing particles were analyzed by the means of
optical and Scanning Electron Microscopy (SEM), Energy Dispersion
Spectroscopy (EDS) and X-Ray Diffraction (XRD). The mechanical
properties were obtained by the transverse rupture strength test. Wear
tests were also performed on the composites and monolithic
porcelain. The best mechanical results were displayed by the
porcelain reinforced with the pre-sintered ZrO2–3%Y2O3
agglomerates.
Abstract: Depositional environment and source potential of the
different organic-rich levels of Devonian age (up to 990m thick) from
the onshore EC-1 well (Southern Tunisia) were investigated based on
the analysis of more than 130 cutting samples by different
geochemical techniques (Rock-Eval pyrolysis, GC-MS). The
obtained results including Rock Eval Pyrolysis data and biomarker
distribution (terpanes, steranes and aromatics) have been used to
describe the depositional environment and to assess the thermal
maturity of the Devonian organic matter. These results show that the
Emsian deposits exhibit poor to fair TOC contents. The associated
organic matter is composed of mixed kerogen (type II/III), as
indicated by the predominance of C29 steranes over C27 and C28
homologous, that was deposited in a slightly reduced environment
favoring organic matter preservation. Thermal maturity assessed from
Tmax, TNR and MPI-1 values shows a mature stage of organic
matter. The Middle Devonian (Eifelian) shales are rich in type II
organic matter that was deposited in an open marine depositional
environment. The TOC values are high and vary between 2 and 7%
indicating good to excellent source rock. The relatively high HI
values (reaching 547 mg HC/g TOC) and the low values of t19/t23
tricyclic terpane ratio (< 0.2) confirm the marine origin of the organic
matter (type II). During the Upper Devonian, the organic matter was
deposited under variable redox conditions, oxic to suboxic which is
clearly indicated by the low C35/C34 hopanes ratio, immature to
marginally mature with the vitrinite reflectance ranging from 0.5 to
0.7 Ro and Tmax value of 426°C-436 °C and the TOC values range
between 0.8% to 4%.
Abstract: After the internet explosion in the 90’s, technology
was immediately integrated into the school system. Technology
which symbolizes advancement in human knowledge was seen as a
setback by many educators. Efforts have been made to help stem this
erroneous believes and help educators realize the benefits of
technology and ways of implementing it in the classrooms especially
in the sciences. This advancement created a constantly expanding gap
between the pupil’s perception on the use of technology within the
learning atmosphere and the teacher’s perception and limitations
hence, the focus of this paper is on the need to refocus on the use of
Science and Technology in enhancing children’s potentials in
learning at school especially in Science for sustainable development
in Nigeria. The paper recommended measures for facilitating the
sustenance of science and technology in Nigerian schools so as to
enhance the potentials of our children in Science and Technology for
a better tomorrow.
Abstract: Taking into account the significance of measuring the
daily use of the study space in the libraries in order to develop and
reorganize the space for enhancing the efficiency of the study space,
the current study aimed to apply GIS in analyzing the study halls of
the Central Library and Document Center of Tehran University in
order to determine how study desks and chairs were used by the
students. The study used a combination of survey-descriptive and
system design method. In order to gather the required data, surveydescriptive
method was used. For implementing and entering data
into ArcGIS and analyzing the data and displaying the results on the
maps of the study halls of the library, system design method was
utilized. The design of the spatial database of the use of the study
halls was measured through the extent of occupancy of the space by
the library users and the maps of the study halls of the central library
of Tehran University as the case study. The results showed that
Abooreyhan hall had the highest rate of occupancy of the desks and
chairs compared to the other halls. The Hall of Science and
Technology, with an average occupancy rate of 0.39 for the tables
represented the lowest number of users and Rashid al-Dins hall, and
Science and Technology hall with an average occupancy rate (0.40)
had the lowest number of users for seats. In this study, the
comparison of the space occupied at different periods in the morning,
evenings, afternoons, and several months was performed through
GIS. This system analyzed the space relationships effectively and
efficiently. The output of this study would be used by administrators
and librarians to determine the exact extent of use of the equipment
of the study halls and librarians can use the output map to design the
space more efficiently at the library.
Abstract: Experimental production methods of Chevreul’s salt
being an intermediate stage product in copper recovery were
investigated on this article. Chevreul’s salt, Cu2SO3.CuSO3.2H2O,
being a mixed valence copper sulphite compound, has been obtained
by using different methods and reagents. Chevreul’s salt has an
intense brick-red color. It is highly stable and expensive. The
production of Chevreul’s salt plays a key role in hydrometallurgy.
Thermodynamic tendency on precipitation of Chevreul’s salt is
related to pH and temperature. Besides, SO2 gaseous is a versatile
reagent for precipitating of copper sulphites, Using of SO2 for
selective precipitation can be made by appropriate adjustments of pH
and temperature. Chevreul’s salt does not form in acidic solutions if
those solutions contains considerable amount of sulfurous acid. It is
necessary to maintain between pH 2–4.5, because, solubility of
Chevreul’s salt increases with decreasing of pH values. Also, the
region which Chevreul’s salt is stable can be seen from the potentialpH
diagram.
Abstract: The mechanisms underlying the association between
obesity and asthma may be related to a decreased immunological
tolerance induced by a defective function of regulatory T cells
(Tregs). The aim of this study is to establish the potential link
between these diseases and CD4+, CD25+ FoxP3+ Tregs as well as T
helper cells (Ths) in children. This is a prospective case control
study. Obese (n:40), asthmatic (n:40), asthmatic obese (n:40) and
healthy children (n:40), who don't have any acute or chronic diseases,
were included in this study. Obese children were evaluated according
to WHO criteria. Asthmatic patients were chosen based on GINA
criteria. Parents were asked to fill up the questionnaire. Informed
consent forms were taken. Blood samples were marked with CD4+,
CD25+ and FoxP3+ in order to determine Tregs and Ths by flow
cytometric method. Statistical analyses were performed. p≤0.05 was
chosen as meaningful threshold. Tregs exhibiting anti-inflammatory
nature were significantly lower in obese (0,16%; p≤0,001), asthmatic
(0,25%; p≤0,01) and asthmatic obese (0,29%; p≤0,05) groups than
the control group (0,38%). Ths were counted higher in asthma group
than the control (p≤0,01) and obese (p≤0,001) groups. T cell
immunity plays important roles in obesity and asthma pathogeneses.
Decreased numbers of Tregs found in obese, asthmatic and asthmatic
obese children may help to elucidate some questions in
pathophysiology of these diseases. For HOMA-IR levels, any
significant difference was not noted between control and obese
groups, but statistically higher values were found for obese
asthmatics. The values obtained in all groups were found to be below
the critical cut off points. This finding has made the statistically
significant difference observed between Tregs of obese, asthmatic,
obese asthmatic and control groups much more valuable. These
findings will be useful in diagnosis and treatment of these disorders
and future studies are needed. The production and propagation of
Tregs may be promising in alternative asthma and obesity treatments.
Abstract: There are several possibilities of reducing the required
amount of cement in concrete production. Natural zeolite is one of
the raw materials which can partly substitute Portland cement. The
effort to reduce the amount of Portland cement used in concrete
production is brings both economical as well as ecological benefits.
The paper presents the properties of concrete containing natural
zeolite as an active admixture in the concrete which partly substitutes
Portland cement. The properties discussed here bring information
about the basic mechanical properties and frost resistance of concrete
containing zeolite. The properties of concretes with the admixture of
zeolite are compared with a reference concrete with no content of
zeolite. The properties of the individual concretes are observed for
360 days.
Abstract: Experimental study of natural convection heat transfer
inside smooth and rough surfaces of vertical and inclined equilateral
triangular channels of different inclination angles with a uniformly
heated surface are performed. The inclination angle is changed from
15º to 90º. Smooth and rough surface of average roughness (0.02mm)
are used and their effect on the heat transfer characteristics are
studied. The local and average heat transfer coefficients and Nusselt
number are obtained for smooth and rough channels at different heat
flux values, different inclination angles and different Rayleigh
numbers (Ra) 6.48 × 105 ≤ Ra ≤ 4.78 × 106. The results show that
the local Nusselt number decreases with increase of axial distance
from the lower end of the triangular channel to a point near the upper
end of channel, and then, it slightly increases. Higher values of local
Nusselt number for rough channel along the axial distance compared
with the smooth channel. The average Nusselt number of rough
channel is higher than that of smooth channel by about 8.1% for
inclined case at θ = 45o and 10% for vertical case. The results
obtained are correlated using dimensionless groups for both rough
and smooth surfaces of the inclined and vertical triangular channels.
Abstract: In the current work, a three-dimensional geometry of a
75% stenosed blood vessel is analyzed. Large eddy simulation (LES)
with the help of a dynamic subgrid scale Smagorinsky model is
applied to model the turbulent pulsatile flow. The geometry, the
transmural pressure and the properties of the blood and the elastic
boundary were based on clinical measurement data. For the flexible
wall model, a thin solid region is constructed around the 75%
stenosed blood vessel. The deformation of this solid region was
modelled as a deforming boundary to reduce the computational cost
of the solid model. Fluid-structure interaction is realized via a twoway
coupling between the blood flow modelled via LES and the
deforming vessel. The information of the flow pressure and the wall
motion was exchanged continually during the cycle by an arbitrary
Lagrangian-Eulerian method. The boundary condition of current time
step depended on previous solutions. The fluctuation of the velocity
in the post-stenotic region was analyzed in the study. The axial
velocity at normalized position Z=0.5 shows a negative value near
the vessel wall. The displacement of the elastic boundary was
concerned in this study. In particular, the wall displacement at the
systole and the diastole were compared. The negative displacement at
the stenosis indicates a collapse at the maximum velocity and the
deceleration phase.
Abstract: Background - The TrendCare Patient Dependency
System is currently used by a large number of maternity Services
across Australia, New Zealand and Singapore. In 2012, 2013 and
2014 validation studies were initiated in all three countries to validate
the acuity tools used for women in labour, and postnatal mothers and
babies. This paper will present the findings of the validation study.
Aim - The aim of this study was to; identify if the care hours
provided by the TrendCare acuity system was an accurate reflection
of the care required by women and babies; obtain evidence of
changes required to acuity indicators and/or category timings to
ensure the TrendCare acuity system remains reliable and valid across
a range of maternity care models in three countries.
Method - A non-experimental action research methodology was
used across maternity services in four District Health Boards in New
Zealand, a large tertiary and a large secondary maternity service in
Singapore and a large public maternity service in Australia.
Standardised data collection forms and timing devices were used to
collect midwife contact times, with women and babies included in the
study. Rejection processes excluded samples when care was not
completed/rationed, and contact timing forms were incomplete. The
variances between actual timed midwife/mother/baby contact and the
TrendCare acuity category times were identified and investigated.
Results - Thirty two (88.9%) of the 36 TrendCare acuity category
timings, fell within the variance tolerance levels when compared to
the actual timings recorded for midwifery care. Four (11.1%)
TrendCare categories provided less minutes of care than the actual
timings and exceeded the variance tolerance level. These were all
night shift category timings. Nine postnatal categories were not able
to be compared as the sample size for these categories was
statistically insignificant. 100% of labour ward TrendCare categories
matched actual timings for midwifery care, all falling within the
variance tolerance levels.
The actual time provided by core midwifery staff to assist lead
maternity carer (LMC) midwives in New Zealand labour wards
showed a significant deviation to previous studies. The findings of
the study demonstrated the need for additional time allocations in
TrendCare to accommodate an increased level of assistance given to
LMC midwives.
Conclusion - The results demonstrated the importance of regularly
validating the TrendCare category timings with actual timings of the
care hours provided. It was evident from the findings that variances
to models of care and length of stay in maternity units have increased
midwifery workloads on the night shift. The level of assistance
provided by the core labour ward staff to the LMC midwife has
increased substantially.
Outcomes - As a consequence of this study, changes were made to
the night duty TrendCare maternity categories, additional acuity
indicators were developed and times for assisting LMC midwives in
labour ward increased. The updated TrendCare version was delivered
to maternity services in 2014.
Abstract: Non-water based fixed abrasive polishing was adopted
to manufacture LBO crystal for nano precision surface quality because
of its deliquescent. Ethyl alcohol was selected as the non-water based
slurry solvent and ethanediamine, lactic acid, hydrogen peroxide was
added in the slurry as a chemical additive, respectively. Effect of
different additives with non-water based slurry on material removal
rate, surface topography, microscopic appearances, and surface
roughness were investigated in fixed abrasive polishing of LBO
crystal. The results show the best surface quality of LBO crystal with
surface roughness Sa 8.2 nm and small damages was obtained by
non-water based slurry with lactic acid. Non-water based fixed
abrasive polishing can achieve nano precision surface quality of LBO
crystal with high material removal.
Abstract: This article presents modeling studies of NiAl alloy
under solid-particle erosion and liquid-drop erosion. In the
solid-particle erosion simulation, attention is paid to the oxide scale
thickness variation on the alloy in high-temperature erosion
environments. The erosion damage is assumed to be deformation wear
and cutting wear mechanisms, incorporating the influence of the oxide
scale on the eroded surface; thus the instantaneous oxide thickness is
the result of synergetic effect of erosion and oxidation. For liquid-drop
erosion, special interest is in investigating the effects of drop velocity
and drop size on the damage of the target surface. The models of
impact stress wave, mean depth of penetration, and maximum depth of
erosion rate (Max DER) are employed to develop various maps for
NiAl alloy, including target thickness vs. drop size (diameter), rate of
mean depth of penetration (MDRP) vs. drop impact velocity, and
damage threshold velocity (DTV) vs. drop size.
Abstract: Air-cooled Blast Furnace Slag Aggregate (BFSA) is
usually referred to as a material providing for unique properties of
concrete. On the other hand, negative influences are also presented in
many aspects. The freeze-thaw resistance of concrete is dependent on
many factors, including regional specifics and when a concrete mix is
specified it is still difficult to tell its exact freeze-thaw resistance due
to the different components affecting it. An important consideration
in working with BFSA is the granularity and whether slag is sorted or
not. The experimental part of the article represents a comparative
testing of concrete using both the sorted and unsorted BFSA through
the freeze-thaw resistance as an indicator of durability. Unsorted
BFSA is able to be successfully used for concretes as they are
specified for exposure class XF4 with providing that the type of
cement is precisely selected.