Abstract: This paper describes analysis of low velocity transverse impact on fully backed sandwich beams with composite faces from Eglass/epoxy and cores from Polyurethane or PVC. Indentation on sandwich beams has been analyzed with the existing theories and modeled with the FE code ABAQUS, also loadings have been done experimentally to verify theoretical results. Impact on fully backed has been modeled in two cases of impactor energy with SDOF model (single-degree-of-freedom) and indentation stiffness: lower energy for elastic indentation of sandwich beams and higher energy for plastic area in indentation. Impacts have been modeled by ABAQUS. Impact results can describe response of beam in terms of core and faces thicknesses, core material, indentor energy and energy absorbed. The foam core is modeled using the crushable foam material model and response of the foam core is experimentally characterized in uniaxial compression with higher velocity loading to define quasi impact behaviour.
Abstract: This study is a descriptive-normative research. It
attempted to investigate the restaurants’ firm performance in terms of
the customers and restaurant personnel’s degree of satisfaction. A
total of 12 restaurants in Bangkok, Thailand that offer Thai cuisine
were included in this study. It involved 24 stockholders/managers,
120 subordinates and 360 customers. General Managers and
restaurants’ stockholders, 10 staffs, and 30 costumers for each
restaurant were chosen for random sampling. This study found that
respondents are slightly satisfied with their work environment but are
generally satisfied with the accessibility to transportation, to malls,
convenience, safety, recreation, noise-free, and attraction; customers
find the Quality of Food in most Thai Cuisines like services, prices of
food, sales promotion, and capital and length of service satisfactory.
Therefore, both stockholder-related and personnel-related factors
which are influenced by restaurant, personnel, and customer-related
factors are partially accepted whereas; customer-related factors which
are influenced by restaurant, personnel and customer-related factors
are rejected.
Abstract: Fuller’s earth is a fine-grained, naturally occurring substance that has a substantial ability to adsorb impurities. In the present study Fuller’s earth has been characterized and used for the removal of Pb(II) from aqueous solution. The effect of various physicochemical parameters such as pH, adsorbent dosage and shaking time on adsorption were studied. The result of the equilibrium studies showed that the solution pH was the key factor affecting the adsorption. The optimum pH for adsorption was 5. Kinetics data for the adsorption of Pb(II) was best described by pseudo-second order model. The effective diffusion co-efficient for Pb(II) adsorption was of the order of 10-8 m2/s. The adsorption data for metal adsorption can be well described by Langmuir adsorption isotherm. The maximum uptake of metal was 103.3 mg/g of adsorbent. Mass transfer analysis was also carried out for the adsorption process. The values of mass transfer coefficients obtained from the study indicate that the velocity of the adsorbate transport from bulk to the solid phase was quite fast. The mean sorption energy calculated from Dubinin-Radushkevich isotherm indicated that the metal adsorption process was chemical in nature.
Abstract: Multi criteria decision making (MCDM) methods like analytic hierarchy process, ELECTRE and multi-attribute utility theory are critically studied. They have irregularities in terms of the reliability of ranking of the best alternatives. The Routing Decision Support (RDS) algorithm is trying to improve some of their deficiencies. This paper gives a mathematical verification that the RDS algorithm conforms to the test criteria for an effective MCDM method when a linear preference function is considered.
Abstract: Semiconductor nanomaterials like TiO2 nanoparticles
(TiO2-NPs) approximately less than 100 nm in diameter have become
a new generation of advanced materials due to their novel and
interesting optical, dielectric, and photo-catalytic properties. With the
increasing use of NPs in commerce, to date few studies have
investigated the toxicological and environmental effects of NPs.
Motivated by the importance of TiO2-NPs that may contribute to the
cancer research field especially from the treatment prospective
together with the fractal analysis technique, we have investigated the
effect of TiO2-NPs on colony morphology in the dark condition
using fractal dimension as a key morphological characterization
parameter. The aim of this work is mainly to investigate the cytotoxic
effects of TiO2-NPs in the dark on the growth of human cervical
carcinoma (HeLa) cell colonies from morphological aspect. The in
vitro studies were carried out together with the image processing
technique and fractal analysis. It was found that, these colonies were
abnormal in shape and size. Moreover, the size of the control
colonies appeared to be larger than those of the treated group. The
mean Df +/- SEM of the colonies in untreated cultures was
1.085±0.019, N= 25, while that of the cultures treated with TiO2-NPs
was 1.287±0.045. It was found that the circularity of the control
group (0.401±0.071) is higher than that of the treated group
(0.103±0.042). The same tendency was found in the diameter
parameters which are 1161.30±219.56 μm and 852.28±206.50 μm
for the control and treated group respectively. Possible explanation of
the results was discussed, though more works need to be done in
terms of the for mechanism aspects. Finally, our results indicate that
fractal dimension can serve as a useful feature, by itself or in
conjunction with other shape features, in the classification of cancer
colonies.
Abstract: The various applications of VLSI circuits in highperformance
computing, telecommunications, and consumer
electronics has been expanding progressively, and at a very hasty
pace. This paper describes a new model for partitioning a circuit
using DBSCAN and fuzzy ARTMAP neural network. The first step
is concerned with feature extraction, where we had make use
DBSCAN algorithm. The second step is the classification and is
composed of a fuzzy ARTMAP neural network. The performance of
both approaches is compared using benchmark data provided by
MCNC standard cell placement benchmark netlists. Analysis of the
investigational results proved that the fuzzy ARTMAP with
DBSCAN model achieves greater performance then only fuzzy
ARTMAP in recognizing sub-circuits with lowest amount of
interconnections between them The recognition rate using fuzzy
ARTMAP with DBSCAN is 97.7% compared to only fuzzy
ARTMAP.
Abstract: Scaffolds play a key role in tissue engineering and can be produced in many different ways depending on the applications and the materials used. Most researchers used an experimental trialand- error approach into new biomaterials but computer simulation applied to tissue engineering can offer a more exhaustive approach to test and screen out biomaterials. This paper develops the model of scaffolds and Computational Fluid Dynamics that show the value of computer simulations in determining the influence of the geometrical scaffold parameter porosity, pore size and shape on the permeability of scaffolds, magnitude of velocity, drop pressure, shear stress distribution and level and the proper design of the geometry of the scaffold. This creates a need for more advanced studies that include aspects of dynamic conditions of a micro fluid passing through the scaffold were characterized for tissue engineering applications and differentiation of tissues within scaffolds.
Abstract: In this paper, a Dynamic Economic Dispatch (DED) model is developed for the system consisting of both thermal generators and wind turbines. The inclusion of a significant amount of wind energy into power systems has resulted in additional constraints on DED to accommodate the intermittent nature of the output. The probability of stochastic wind power based on the Weibull probability density function is included in the model as a constraint; A Here-and-Now Approach. The Environmental Protection Agency-s hourly emission target, which gives the maximum emission during the day, is used as a constraint to reduce the atmospheric pollution. A 69-bus test system with non-smooth cost function is used to illustrate the effectiveness of the proposed model compared with static economic dispatch model with including the wind power.
Abstract: Thepurpose of the research is to characterize the levels
of satisfaction of the students in e-learning post-graduate courses,
taking into account specific dimensions of the course which were
considered as benchmarks for the quality of this type of online
learning initiative, as well as the levels of satisfaction towards each
specific indicator identified in each dimension. It was also an aim of
this study to understand how thesedimensions relate to one another.
Using a quantitative research approach in the collection and analysis
of the data, the study involves the participation of the students who
attended on e-learning course in 2010/2011. The conclusions of this
study suggest that online students present relatively high levels of
satisfaction, which points towards a positive experience during the
course. It is possible to note that there is a correlation between the
different dimensions studied, consequently leading to different
improvement strategies. Ultimately, this investigation aims to
contribute to the promotion of quality and the success of e-learning
initiatives in Higher Education.
Abstract: This paper describes WiPoD (Wireless Position
Detector) which is a pure software based location determination and
tracking (positioning) system. It uses empirical signal strength measurements from different wireless access points for mobile user
positioning. It is designed to determine the location of users having
802.11 enabled mobile devices in an 802.11 WLAN infrastructure
and track them in real time. WiPoD is the first main module in our
LBS (Location Based Services) framework. We tested K-Nearest
Neighbor and Triangulation algorithms to estimate the position of a
mobile user. We also give the analysis results of these algorithms for
real time operations. In this paper, we propose a supportable, i.e.
understandable, maintainable, scalable and portable wireless
positioning system architecture for an LBS framework. The WiPoD
software has a multithreaded structure and was designed and implemented with paying attention to supportability features and real-time constraints and using object oriented design principles. We also describe the real-time software design issues of a wireless positioning system which will be part of an LBS framework.
Abstract: The mechanical deformation and the electrical conductivity of lanthanum strontium cobalt ferrite oxide under uniaxial compression were investigated at various temperatures up to 1073 K. The material reveals a rather complex mechanical behaviour related to its ferroelasticity and completely different stress-strain curves are obtained during the 1st and 2nd loading cycles. A distinctive ferroelastic creep was observed at 293 K whilst typical ferroelastic stress-strain curve were obtained in the temperature range from 473 K to 873 K. At 1073 K, on the other hand, high-temperature creep deformation was observed instead of ferroelastic deformation. The conductivity increases with increasing compressive stress at all the temperatures. The increase in conductivity is related to both geometrical and piezoelectric effects. From 293 K to 873 K, where the material exhibits ferroelastic behaviour, the variation in the total conductivity decreases with increasing temperature. The contribution of the piezoelectric effect to the total conductivity variation also decreases with increasing temperature and the maximum in piezoconductivity has a value of about 0.75 % at 293 K for a compressive stress of 100 MPa. There is no effect of domain switching on conductivity except for the geometric effect. At 1073 K, the conductivity is simply proportional to the compressive strain.
Abstract: Mutations of the telomeric copy of the survival motor neuron 1 (SMN1) gene cause spinal muscular atrophy. A deletion of the Eef1a2 gene leads to lower motor neuron degeneration in wasted mice. Indirect evidences have been shown that the eEF1A protein family may interact with SMN, and our previous study showed that abnormalities of neuromuscular junctions in wasted mice were similar to those of Smn mutant mice. To determine potential colocalization between SMN and tissue-specific translation elongation factor 1A2 (eEF1A2), an immunochemical analysis of HeLa cells transfected with the plasmid pcDNA3.1(+)C-hEEF1A2- myc and a new quantitative test of colocalization by intensity correlation analysis (ICA) was used to explore the association of SMN and eEF1A2. Here the results showed that eEF1A2 redistributed from the cytoplasm to the nucleus in response to serum and epidermal growth factor. In the cytoplasm, compelling evidence showed that staining for myc-tagged eEF1A2 varied in synchrony with that for SMN, consistent with the formation of a SMN-eEF1A2 complex in the cytoplasm of HeLa cells. These findings suggest that eEF1A2 may colocalize with SMN in the cytoplasm and may be a component of the SMN complex. However, the limitation of the ICA method is an inability to resolve colocalization in components of small organelles such as the nucleus.
Abstract: This paper presents a new and efficient approach for capacitor placement in radial distribution systems that determine the optimal locations and size of capacitor with an objective of improving the voltage profile and reduction of power loss. The solution methodology has two parts: in part one the loss sensitivity factors are used to select the candidate locations for the capacitor placement and in part two a new algorithm that employs Plant growth Simulation Algorithm (PGSA) is used to estimate the optimal size of capacitors at the optimal buses determined in part one. The main advantage of the proposed method is that it does not require any external control parameters. The other advantage is that it handles the objective function and the constraints separately, avoiding the trouble to determine the barrier factors. The proposed method is applied to 9, 34, and 85-bus radial distribution systems. The solutions obtained by the proposed method are compared with other methods. The proposed method has outperformed the other methods in terms of the quality of solution.
Abstract: The main emphasis of metallurgists has been to process the materials to obtain the balanced mechanical properties for the given application. One of the processing routes to alter the properties is heat treatment. Nearly 90% of the structural applications are related to the medium carbon an alloyed steels and hence are regarded as structural steels. The major requirement in the conventional steel is to improve workability, toughness, hardness and grain refinement. In this view, it is proposed to study the mechanical and tribological properties of unalloyed structural (AISI 1140) steel with different thermal (heat) treatments like annealing, normalizing, tempering and hardening and compared with as brought (cold worked) specimen. All heat treatments are carried out in atmospheric condition. Hardening treatment improves hardness of the material, a marginal decrease in hardness value with improved ductility is observed in tempering. Annealing and normalizing improve ductility of the specimen. Normalized specimen shows ultimate ductility. Hardened specimen shows highest wear resistance in the initial period of slide wear where as above 25KM of sliding distance, as brought steel dominates the hardened specimen. Both mild and severe wear regions are observed. Microstructural analysis shows the existence of pearlitic structure in normalized specimen, lath martensitic structure in hardened, pearlitic, ferritic structure in annealed specimen.
Abstract: This study was carried out to develop a flotation
procedure for an oxide copper ore from a Region in Central Africa
for producing an 18% copper concentrate for downstream processing
at maximum recovery from a 4% copper feed grade. The copper
recoveries achieved from the test work were less than 50% despite
changes in reagent conditions (multistage sulphidisation, use of RCA
emulsion and mixture, use of AM 2, etc). The poor recoveries were
attributed to the mineralogy of the ore from which copper silicates
accounted for approximately 70% (mass) of the copper minerals in
the ore. These can be complex and difficult to float using
conventional flotation methods. Best results were obtained using
basic sulphidisation procedures, a high flotation temperature and
extended flotation residence time.
Abstract: Fishbone of Nile Tilapia (Tilapia nilotica), waste from the frozen Nile Tilapia fillet factory, is one of calcium sources. In order to increase fish bone powder value, this study aimed to investigate the effect of Tilapia bone flour (TBF) addition (5, 10, 15% by flour weight) on cooking quality, texture and sensory attributes of noodles. The results indicated that tensile strength, color value (a*) and water absorption of noodles significantly decreased (p£0.05) as the levels of TBF increased from 0-15%. While cooking loss, cooking time and color values (L* and b*) of noodles significantly increased (p£0.05). Sensory evaluation indicated that noodles with 5% TBF received the highest overall acceptability score.
Abstract: Human Resource (HR) applications can be used to
provide fair and consistent decisions, and to improve the
effectiveness of decision making processes. Besides that, among
the challenge for HR professionals is to manage organization
talents, especially to ensure the right person for the right job at the
right time. For that reason, in this article, we attempt to describe
the potential to implement one of the talent management tasks i.e.
identifying existing talent by predicting their performance as one of
HR application for talent management. This study suggests the
potential HR system architecture for talent forecasting by using
past experience knowledge known as Knowledge Discovery in
Database (KDD) or Data Mining. This article consists of three
main parts; the first part deals with the overview of HR
applications, the prediction techniques and application, the general
view of Data mining and the basic concept of talent management
in HRM. The second part is to understand the use of Data Mining
technique in order to solve one of the talent management tasks, and
the third part is to propose the potential HR system architecture for
talent forecasting.
Abstract: A multiphase harmonic load flow algorithm is developed based on backward/forward sweep to examine the effects of various factors on the neutral to earth voltage (NEV), including unsymmetrical system configuration, load unbalance and harmonic injection. The proposed algorithm composes fundamental frequency and harmonic frequencies power flows. The algorithm and the associated models are tested on IEEE 13 bus system. The magnitude of NEV is investigated under various conditions of the number of grounding rods per feeder lengths, the grounding rods resistance and the grounding resistance of the in feeding source. Additionally, the harmonic injection of nonlinear loads has been considered and its influences on NEV under different conditions are shown.
Abstract: The compressive strength development through
polymerization process of alkaline solution and fly ash blended with Microwave Incinerated Rice Husk Ash (MIRHA) is described in this
paper. Three curing conditions, which are hot gunny curing, ambient
curing, and external humidity curing are investigated to obtain the suitable curing condition for cast in situ provision. Fly ash was
blended with MIRHA at 3%, 5%, and 7% to identify the effect of blended mixes to the compressive strength and microstructure
properties of geopolymer concrete. Compressive strength results
indicated an improvement in the strength development with external humidity curing concrete samples compared to hot gunny curing and
ambient curing. Blended mixes also presented better performance
than control mixes. Improvement of interfacial transition zone (ITZ)
and micro structure in external humidity concrete samples were also
identified compared to hot gunny and ambient curing.
Abstract: Data Envelopment Analysis (DEA) is one of the most
widely used technique for evaluating the relative efficiency of a set
of homogeneous decision making units. Traditionally, it assumes that
input and output variables are known in advance, ignoring the critical
issue of data uncertainty. In this paper, we deal with the problem
of efficiency evaluation under uncertain conditions by adopting the
general framework of the stochastic programming. We assume that
output parameters are represented by discretely distributed random
variables and we propose two different models defined according to a
neutral and risk-averse perspective. The models have been validated
by considering a real case study concerning the evaluation of the
technical efficiency of a sample of individual firms operating in
the Italian leather manufacturing industry. Our findings show the
validity of the proposed approach as ex-ante evaluation technique
by providing the decision maker with useful insights depending on
his risk aversion degree.