Abstract: Nanocrystalline powders of the lead-free piezoelectric
material, tantalum-substituted potassium sodium niobate
(K0.5Na0.5)(Nb0.9Ta0.1)O3 (KNNT), were produced using a Retsch
PM100 planetary ball mill by setting the milling time to 15h, 20h,
25h, 30h, 35h and 40h, at a fixed speed of 250rpm. The average
particle size of the milled powders was found to decrease from 12nm
to 3nm as the milling time increases from 15h to 25h, which is in
agreement with the existing theoretical model. An anomalous
increase to 98nm and then a drop to 3nm in the particle size were
observed as the milling time further increases to 30h and 40h
respectively. Various sizes of these starting KNNT powders were
used to investigate the effect of milling time on the microstructure,
dielectric properties, phase transitions and piezoelectric properties of
the resulting KNNT ceramics. The particle size of starting KNNT
was somewhat proportional to the grain size. As the milling time
increases from 15h to 25h, the resulting ceramics exhibit
enhancement in the values of relative density from 94.8% to 95.8%,
room temperature dielectric constant (εRT) from 878 to 1213, and
piezoelectric charge coefficient (d33) from 108pC/N to 128pC/N. For
this range of ceramic samples, grain size refinement suppresses the
maximum dielectric constant (εmax), shifts the Curie temperature (Tc)
to a lower temperature and the orthorhombic-tetragonal phase
transition (Tot) to a higher temperature. Further increase of milling
time from 25h to 40h produces a gradual degradation in the values of
relative density, εRT, and d33 of the resulting ceramics.
Abstract: The research conducted in early seventies apparently
assumed the existence of a universal decision model for union
negotiators and furthermore tended to regard financial information as
a ‘neutral’ input into a rational decision making process. However,
research in the eighties began to question the neutrality of financial
information as an input in collective bargaining rather viewing it as a
potentially effective means for controlling the labour force.
Furthermore, this later research also started challenging the simplistic
assumptions relating particularly to union objectives which have
underpinned the earlier search for universal union decision models.
Despite the above developments there seems to be a dearth of studies
in developing countries concerning the use of financial information in
collective bargaining. This paper seeks to begin to remedy this
deficiency. Utilising a case study approach based on two enterprises,
one in the public sector and the other a multinational, the universal
decision model is rejected and it is argued that the decision whether
or not to use financial information is a contingent one and such a
contingency is largely defined by the context and environment in
which both union and management negotiators work. An attempt is
also made to identify the factors constraining as well as promoting
the use of financial information in collective bargaining, these being
regarded as unique to the organisations within which the case studies
are conducted.
Abstract: As enterprise computing becomes more and more
complex, the costs and technical challenges of IT system maintenance
and support are increasing rapidly. One popular approach to managing
IT system maintenance is to prepare and use a FAQ (Frequently Asked
Questions) system to manage and reuse systems knowledge. Such a
FAQ system can help reduce the resolution time for each service
incident ticket. However, there is a major problem where over time the
knowledge in such FAQs tends to become outdated. Much of the
knowledge captured in the FAQ requires periodic updates in response
to new insights or new trends in the problems addressed in order to
maintain its usefulness for problem resolution. These updates require a
systematic approach to define the exact portion of the FAQ and its
content. Therefore, we are working on a novel method to
hierarchically structure the FAQ and automate the updates of its
structure and content. We use structured information and the
unstructured text information with the timelines of the information in
the service incident tickets. We cluster the tickets by structured
category information, by keywords, and by keyword modifiers for the
unstructured text information. We also calculate an urgency score
based on trends, resolution times, and priorities. We carefully studied
the tickets of one of our projects over a 2.5-year time period. After the
first 6 months we started to create FAQs and confirmed they improved
the resolution times. We continued observing over the next 2 years to
assess the ongoing effectiveness of our method for the automatic FAQ
updates. We improved the ratio of tickets covered by the FAQ from
32.3% to 68.9% during this time. Also, the average time reduction of
ticket resolution was between 31.6% and 43.9%. Subjective analysis
showed more than 75% reported that the FAQ system was useful in
reducing ticket resolution times.
Abstract: Enterprise Architecture (EA) Implementation
Methodologies have become an important part of EA projects.
Several implementation methodologies have been proposed, as a
theoretical and practical approach, to facilitate and support the
development of EA within an enterprise. A significant question when
facing the starting of EA implementation is deciding which
methodology to utilize. In order to answer this question, a framework
with several criteria is applied in this paper for the comparative
analysis of existing EA implementation methodologies. Five EA
implementation methodologies including: EAP, TOGAF, DODAF,
Gartner, and FEA are selected in order to compare with proposed
framework. The results of the comparison indicate that those
methodologies have not reached a sufficient maturity as whole due to
lack of consideration on requirement management, maintenance,
continuum, and complexities in their process. The framework has
also ability for the evaluation of any kind of EA implementation
methodologies.
Abstract: Many problems in science and engineering field require
the solution of shifted linear systems with multiple right hand
sides and multiple shifts. To solve such systems efficiently, the
implicitly restarted global GMRES algorithm is extended in this
paper. However, the shift invariant property could no longer hold over
the augmented global Krylov subspace due to adding the harmonic
Ritz matrices. To remedy this situation, we enforce the collinearity
condition on the shifted system and propose shift implicitly restarted
global GMRES. The new method not only improves the convergence
but also has a potential to simultaneously compute approximate
solution for the shifted systems using only as many matrix vector
multiplications as the solution of the seed system requires. In
addition, some numerical experiments also confirm the effectiveness
of our method.
Abstract: We have experimentally demonstrated bright-dark
pulses in a nonlinear polarization rotation (NPR) based mode-locked
Erbium-doped fiber laser (EDFL) with a long cavity configuration.
Bright–dark pulses could be achieved when the laser works in the
passively mode-locking regime and the net group velocity dispersion
is quite anomalous. The EDFL starts to generate a bright pulse train
with degenerated dark pulse at the mode-locking threshold pump
power of 35.09 mW by manipulating the polarization states of the
laser oscillation modes using a polarization controller (PC). A split
bright–dark pulse is generated when further increasing the pump
power up to 37.95 mW. Stable bright pulses with no obvious
evidence of a dark pulse can also be generated when further adjusting
PC and increasing the pump power up to 52.19 mW. At higher pump
power of 54.96 mW, a new form of bright-dark pulse emission was
successfully identified with the repetition rate of 29 kHz. The bright
and dark pulses have a duration of 795.5 ns and 640 ns, respectively.
Abstract: In this paper it was examined the influence of margin
regulation on stock market volatility in EU 1993 – 2014. Regulating
margin requirements or haircuts for securities financing transactions
has for a long time been considered as a potential tool to limit the
build-up of leverage and dampen volatility in financial markets. The
margin requirement dictates how much investors can borrow against
these securities. Margin can be an important part of investment.
Using daily and monthly stock returns and there is no convincing
evidence that EU Regulation margin requirements have served to
dampen stock market volatility. In this paper was detected the
expected negative relation between margin requirements and the
amount of margin credit outstanding. Also, it confirmed that changes
in margin requirements by the EU regulation have tended to follow
than lead changes in market volatility. For the analysis have been
used the modified Levene statistics to test whether the standard
deviation of stock returns in the 25, 50 and 100 days preceding
margin changes is the same as that in the succeeding 25, 50 and 100
days. The analysis started in May 1993 when it was first empowered
to set the initial margin requirement and the last sample was in May
2014. To test whether margin requirements influence stock market
volatility over the long term, the sample of stock returns was divided
into 14 periods, according to the 14 changes in margin requirements.
Abstract: Kuosheng nuclear power plant (NPP) is a BWR/6 type
NPP and located on the northern coast of Taiwan. First, Kuosheng
NPP TRACE model were developed in this research. In order to assess
the system response of Kuosheng NPP TRACE model, startup tests
data were used to evaluate Kuosheng NPP TRACE model. Second, the
overpressurization transient analysis of Kuosheng NPP TRACE model
was performed. Besides, in order to confirm the mechanical property
and integrity of fuel rods, FRAPTRAN analysis was also performed in
this study.
Abstract: Voltage sags are the most common power quality
disturbance in the distribution system. It occurs due to the fault in the
electrical network or by the starting of a large induction motor and
this can be solved by using the custom power devices such as
Dynamic Voltage Restorer (DVR). In this paper DVR is proposed to
compensate voltage sags on critical loads dynamically. The DVR
consists of VSC, injection transformers, passive filters and energy
storage (lead acid battery). By injecting an appropriate voltage, the
DVR restores a voltage waveform and ensures constant load voltage.
The simulation and experimental results of a DVR using MATLAB
software shows clearly the performance of the DVR in mitigating
voltage sags.
Abstract: This research proposes a novel reconstruction protocol
for restoring missing surfaces and low-quality edges and shapes in
photos of artifacts at historical sites. The protocol starts with the
extraction of a cloud of points. This extraction process is based on
four subordinate algorithms, which differ in the robustness and
amount of resultant. Moreover, they use different -but
complementary- accuracy to some related features and to the way
they build a quality mesh. The performance of our proposed protocol
is compared with other state-of-the-art algorithms and toolkits. The
statistical analysis shows that our algorithm significantly outperforms
its rivals in the resultant quality of its object files used to reconstruct
the desired model.
Abstract: Researches and concerns in power quality gained
significant momentum in the field of power electronics systems over
the last two decades globally. This sudden increase in the number of
concerns over power quality problems is a result of the huge increase
in the use of non-linear loads. In this paper, power quality evaluation
of some distribution networks at Misurata - Libya has been done
using a power quality and energy analyzer (Fluke 437 Series II). The
results of this evaluation are used to minimize the problems of power
quality. The analysis shows the main power quality problems that
exist and the level of awareness of power quality issues with the aim
of generating a start point which can be used as guidelines for
researchers and end users in the field of power systems.
Abstract: The fight against climate change and the replacement
of fossil energies nearing exhaustion gradually emerge as major
societal and economic challenges. It is possible to develop common
dates of low commercial value, and put on the local and international
market a new generation of products with high added values such as
bio ethanol. Besides its use in chemical synthesis, bio ethanol can be
blended with gasoline to produce a clean fuel while improving the
octane.
Abstract: In this paper the vibration of a synchronous belt drive
during start-up is analyzed and discussed. Besides considering the
belt elasticity, the model here proposed also takes into consideration
the electromagnetic response of the DC motor. The solution of the
motion equations is obtained by means of the modal analysis in
state space, which allows to obtain the decoupling of all equations,
without introducing the hypothesis of proportional damping. The
mathematical model of the transmission and the solution algorithms
have been implemented within a computing software that allows the
user to simulate the dynamics of the system and to evaluate the effects
due to the elasticity of the belt branches and to the electromagnetic
behavior of the DC motor. In order to show the details of the
calculation procedure, the paper presents a case study developed with
the aid of the above-mentioned software.
Abstract: The concept of corporate social responsibility (CSR) in the Czech Republic has evolved notably during the last few years and an issue that started as an interest- and motive-based activity for businesses is becoming more commonplace. Governments have a role to play in ensuring that corporations behave according to the rules and norms of society and can legislate, foster, collaborate with businesses and endorse good practice in order to facilitate the development of CSR. The purpose of this paper is to examine the opportunities and options of CSR in government policy and research its relevance to a business sector. An increasing number of companies is engaging in responsible activities, the public awareness of CSR is rising, and customers are giving higher importance to CSR of companies in their choice. By drawing on existing CSR approach in Czech and understanding of CSR are demonstrated. The paper provides an overview, more detailed government approach of CSR.
Abstract: In the past, the most comprehensively adopted light
source was incandescent light bulbs, but with the appearance of LED
light sources, traditional light sources have been gradually replaced by
LEDs because of its numerous superior characteristics. However,
many of the standards do not apply to LEDs as the two light sources
are characterized differently. This also intensifies the significance of
studies on LEDs. As a Kansei design study investigating the visual
glare produced by traffic arrows implemented with LEDs, this study
conducted a semantic analysis on the styles of traffic arrows used in
domestic and international occasions. The results will be able to
reduce drivers’ misrecognition that results in the unsuccessful arrival
at the destination, or in traffic accidents. This study started with a
literature review and surveyed the status quo before conducting
experiments that were divided in two parts. The first part involved a
screening experiment of arrow samples, where cluster analysis was
conducted to choose five representative samples of LED displays. The
second part was a semantic experiment on the display of arrows using
LEDs, where the five representative samples and the selected ten
adjectives were incorporated. Analyzing the results with
Quantification Theory Type I, it was found that among the
composition of arrows, fletching was the most significant factor that
influenced the adjectives. In contrast, a “no fletching” design was
more abstract and vague. It lacked the ability to convey the intended
message and might bear psychological negative connotation including
“dangerous,” “forbidden,” and “unreliable.” The arrow design
consisting of “> shaped fletching” was found to be more concrete and
definite, showing positive connotation including “safe,” “cautious,”
and “reliable.” When a stimulus was placed at a farther distance, the
glare could be significantly reduced; moreover, the visual evaluation
scores would be higher. On the contrary, if the fletching and the shaft
had a similar proportion, looking at the stimuli caused higher
evaluation at a closer distance. The above results will be able to be
applied to the design of traffic arrows by conveying information
definitely and rapidly. In addition, drivers’ safety could be enhanced
by understanding the cause of glare and improving visual
recognizability.
Abstract: Today, the means of following the developments in
the area of science and technology is to keep up with the pace of the
advancements in this area. As is in every profession, apart from their
personal efforts, the training of teachers in the period after they start
their careers is only possible through in-service training. The aim of
the present study is to determine the views of Information
Technologies (IT) teachers regarding the in-service training courses
organized by the Ministry of National Education. In this study, in
which quantitative research methods and techniques were employed,
the views of 196 IT teachers were collected by using the “Views on
In-service Training” questionnaire developed by the authors of the
paper. Independent groups t-test was used to determine whether the
views of IT teachers regarding in-service training differed depending
on gender, age and professional seniority. One-way analysis of
variance (ANOVA) was used to investigate whether the views of IT
teachers regarding in-service training differed depending on the
number of in-service training courses they joined and the type of inservice
training course they wanted to take. According to the findings
obtained in the study, the views of IT teachers on in-service training
did not show a significant difference depending on gender and age,
whereas those views differed depending on professional seniority, the
number of in-service training courses they joined and the type of inservice
training course they wanted to take.
Abstract: In this paper, a backward semi-Lagrangian scheme
combined with the second-order backward difference formula
is designed to calculate the numerical solutions of nonlinear
advection-diffusion equations. The primary aims of this paper are
to remove any iteration process and to get an efficient algorithm
with the convergence order of accuracy 2 in time. In order to achieve
these objects, we use the second-order central finite difference and the
B-spline approximations of degree 2 and 3 in order to approximate
the diffusion term and the spatial discretization, respectively. For the
temporal discretization, the second order backward difference formula
is applied. To calculate the numerical solution of the starting point
of the characteristic curves, we use the error correction methodology
developed by the authors recently. The proposed algorithm turns out
to be completely iteration free, which resolves the main weakness
of the conventional backward semi-Lagrangian method. Also, the
adaptability of the proposed method is indicated by numerical
simulations for Burgers’ equations. Throughout these numerical
simulations, it is shown that the numerical results is in good
agreement with the analytic solution and the present scheme offer
better accuracy in comparison with other existing numerical schemes.
Abstract: In this paper, for detection of inclined eccentricity in an induction motor, time–frequency analysis of the stator startup current is carried out. For this purpose, the discrete wavelet transform is used. Data are obtained from simulations, using winding function approach. The results show the validity of the approach for detecting the fault and discriminating with respect to other faults.
Abstract: Accurate Short Term Load Forecasting (STLF) is essential for a variety of decision making processes. However, forecasting accuracy can drop due to the presence of uncertainty in the operation of energy systems or unexpected behavior of exogenous variables. Interval Type 2 Fuzzy Logic System (IT2 FLS), with additional degrees of freedom, gives an excellent tool for handling uncertainties and it improved the prediction accuracy. The training data used in this study covers the period from January 1, 2012 to February 1, 2012 for winter season and the period from July 1, 2012 to August 1, 2012 for summer season. The actual load forecasting period starts from January 22, till 28, 2012 for winter model and from July 22 till 28, 2012 for summer model. The real data for Iraqi power system which belongs to the Ministry of Electricity.
Abstract: The design of an optimised horizontal axis 5-meter-long wind turbine rotor blade in according with IEC 61400-2 standard is a research and development project in order to fulfil the requirements of high efficiency of torque from wind production and to optimise the structural components to the lightest and strongest way possible. For this purpose, a research study is presented here by focusing on the structural characteristics of a composite wind turbine blade via finite element modelling and analysis tools. In this work, first, the required data regarding the general geometrical parts are gathered. Then, the airfoil geometries are created at various sections along the span of the blade by using CATIA software to obtain the two surfaces, namely; the suction and the pressure side of the blade in which there is a hat shaped fibre reinforced plastic spar beam, so-called chassis starting at 0.5m from the root of the blade and extends up to 4 m and filled with a foam core. The root part connecting the blade to the main rotor differential metallic hub having twelve hollow threaded studs is then modelled. The materials are assigned as two different types of glass fabrics, polymeric foam core material and the steel-balsa wood combination for the root connection parts. The glass fabrics are applied using hand wet lay-up lamination with epoxy resin as METYX L600E10C-0, is the unidirectional continuous fibres and METYX XL800E10F having a tri-axial architecture with fibres in the 0,+45,-45 degree orientations in a ratio of 2:1:1. Divinycell H45 is used as the polymeric foam. The finite element modelling of the blade is performed via MSC PATRAN software with various meshes created on each structural part considering shell type for all surface geometries, and lumped mass were added to simulate extra adhesive locations. For the static analysis, the boundary conditions are assigned as fixed at the root through aforementioned bolts, where for dynamic analysis both fixed-free and free-free boundary conditions are made. By also taking the mesh independency into account, MSC NASTRAN is used as a solver for both analyses. The static analysis aims the tip deflection of the blade under its own weight and the dynamic analysis comprises normal mode dynamic analysis performed in order to obtain the natural frequencies and corresponding mode shapes focusing the first five in and out-of-plane bending and the torsional modes of the blade. The analyses results of this study are then used as a benchmark prior to modal testing, where the experiments over the produced wind turbine rotor blade has approved the analytical calculations.