Abstract: Optimization of rational geometrical and mechanical
parameters of panel with curved plywood ribs is considered in this
paper. The panel consists of cylindrical plywood ribs manufactured
from Finish plywood, upper and bottom plywood flange, stiffness
diaphragms. Panel is filled with foam. Minimal ratio of structure self
weight and load that could be applied to structure is considered as
rationality criteria. Optimization is done, by using classical beam
theory without nonlinearities. Optimization of discreet design
variables is done by Genetic algorithm.
Abstract: The cable tower of Liede Bridge is a double-column curved-lever arched-beam portal framed structure. Being novel and unique in structure, its cable tower differs in complexity from traditional ones. This paper analyzes the ultimate load capacity of cable tower by adopting the finite element calculations and model tests which indicate that constitutive relations applied here give a better simulation of actual failure process of prestressed reinforced concrete. In vertical load, horizontal load and overloading tests, the stepped loading of the tower model is of linear relationship, and the test data has good repeatability. All suggests that the cable tower has good bearing capacity, rational design and high emergency capacity.
Abstract: Shear walls are used in most of the tall buildings for
carrying the lateral load. When openings for doors or windows are
necessary to be existed in the shear walls, a special type of the shear
walls is used called "coupled shear walls" which in some cases is
stiffened by specific beams and so, called "stiffened coupled shear
walls".
In this paper, a mathematical method for geometrically nonlinear
analysis of the stiffened coupled shear walls has been presented.
Then, a suitable formulation for determining the critical load of the
stiffened coupled shear walls under gravity force has been proposed.
The governing differential equations for equilibrium and deformation
of the stiffened coupled shear walls have been obtained by setting up
the equilibrium equations and the moment-curvature relationships for
each wall. Because of the complexity of the differential equation, the
energy method has been adopted for approximate solution of the
equations.
Abstract: In the modern construction practices, industrial wastes
or by-products are largely used as raw materials in cement and
concrete. These impart many benefits to the environment and bringabout
an economic impact because the cost of waste disposal is
constantly increasing due to strict environmental regulations. It was
reported in literature that the leakage of oil onto concrete element in
older cement grinding unit resulted in concrete with greater resistance
to freezing and thawing. This effect was thought to be similar to
adding an air-entraining chemical admixture to concrete. This paper
presents an investigation on the load deflection behaviour and crack
patterns of reinforced concrete (RC) beams subjected to four point
loading. Ten 120x260x1900 mm beams were cast with 100%
ordinary Portland cement (OPC) concrete, 20% fly ash (FA) and 20%
rice husk ash (RHA) blended cement concrete. 0.15% dosage of
admixtures (used engine oil, new engine oil, and superplasticizer)
was used throughout the experiment. Results show that OPC and
OPC/RHA RC beams containing used engine oil and superplasticizer
exhibit higher capacity, 18-26% than their corresponding control
mix.
Abstract: Without uncertainty by applying external loads on
beams, bending is created. The created bending in I-beams, puts one
of the flanges in tension and the other one in compression. With increasing of bending, compression flange buckled and beam in out
of its plane direction twisted, this twisting well-known as Lateral Torsional Buckling. Providing bending moment varieties along the
beam, the critical moment is greater than the case its under pure bending. In other words, the value of bending gradient coefficient is
always greater than unite. In this article by the use of " ANSYS 10.0" software near 80 3-D finite element models developed for the
propose of analyzing beams` lateral torsional buckling and surveying influence of slenderness on beams' bending gradient coefficient.
Results show that, presented Cb coefficient via AISC is not correct for some of beams and value of this coefficient is smaller than what proposed by AISC. Therefore instead of using a constant Cb for each
case of loading , a function with two criterion for calculation of Cb coefficient for some cases is proposed.
Abstract: A method based on the power series solution is proposed to solve the natural frequency of flapping vibration for the rotating inclined Euler beam with constant angular velocity. The vibration of the rotating beam is measured from the position of the corresponding steady state axial deformation. In this paper the governing equations for linear vibration of a rotating Euler beam are derived by the d'Alembert principle, the virtual work principle and the consistent linearization of the fully geometrically nonlinear beam theory in a rotating coordinate system. The governing equation for flapping vibration of the rotating inclined Euler beam is linear ordinary differential equation with variable coefficients and is solved by a power series with four independent coefficients. Substituting the power series solution into the corresponding boundary conditions at two end nodes of the rotating beam, a set of homogeneous equations can be obtained. The natural frequencies may be determined by solving the homogeneous equations using the bisection method. Numerical examples are studied to investigate the effect of inclination angle on the natural frequency of flapping vibration for rotating inclined Euler beams with different angular velocity and slenderness ratio.
Abstract: In this paper, the torsion capacity of ultimate point on rectangular beams with spiral reinforcements in the torsion direction and its anti-direction are investigated. Therefore, models of above-mentioned beams have been numerically analyzed under various loads using ANSYS software. It was observed that, spirallyreinforced prismatic beam and beam with spiral links, show lower torsion capacity than beam with normal links also in anti-direction. The result is that the concrete regulations are violated in this case.
Abstract: This paper deals with the problem of non-uniform
torsion in thin-walled elastic beams with asymmetric cross-section,
removing the basic concept of a fixed center of twist, necessary in the
Vlasov-s and Benscoter-s theories to obtain a warping stress field
equivalent to zero. In this new torsion/flexure theory, despite of the
classical ones, the warping function will punctually satisfy the first
indefinite equilibrium equation along the beam axis and it wont- be
necessary to introduce the classical congruence condition, to take into
account the effect of the beam restraints. The solution, based on the
Fourier development of the displacement field, is obtained assuming
that the applied external torque is constant along the beam axis and
on both beam ends the unit twist angle and the warping axial
displacement functions are totally restrained.
Finally, in order to verify the feasibility of the proposed method
and to compare it with the classical theories, two applications are
carried out. The first one, relative to an open profile, is necessary to
test the numerical method adopted to find the solution; the second
one, instead, is relative to a simplified containership section,
considered as full restrained in correspondence of two adjacent
transverse bulkheads.
Abstract: To investigate the applicability of the EDR-2 film for
clinical radiation dosimetry, percentage depth-doses, profiles and
distributions in open and dynamically wedged fields were measured
using film and compared with data from a Treatment Planning
system.The validity of the EDR2 film to measure dose in a plane
parallel to the beam was tested by irradiating 10 cm×10 cm and 4
cm×4 cm fields from a Siemens, primus linac with a 6MV beam and
a source-to-surface distance of 100 cm. The film was placed
Horizontally between solid water phantom blocks and marked
with pin holes at a depth of 10 cm from the incident beam surface.
The film measurement results, in absolute dose, were compared with
ion chamber measurements using a Welhoffer scanning water tank
system and Treatment Planning system. Our results indicate a
maximum underestimate of calculated dose of 8 % with Treatment
Planning system.
Abstract: The paper deals with an analysis of visibility records collected from 210 European airports to obtain a realistic estimation of the availability of Free Space Optical (FSO) data links. Commercially available optical links usually operate in the 850nm waveband. Thus the influence of the atmosphere on the optical beam and on the visible light is similar. Long-term visibility records represent an invaluable source of data for the estimation of the quality of service of FSO links. The model used characterizes both the statistical properties of fade depths and the statistical properties of individual fade durations. Results are presented for Italy, France, and Germany.
Abstract: The present work deals with the structural analysis of
turbine blades and modeling of turbine blades. A common failure
mode for turbine machines is high cycle of fatigue of compressor and
turbine blades due to high dynamic stresses caused by blade vibration
and resonance within the operation range of the machinery. In this
work, proper damping system will be analyzed to reduce the
vibrating blade. The main focus of the work is the modeling of under
platform damper to evaluate the dynamic analysis of turbine-blade
vibrations. The system is analyzed using Bond graph technique. Bond
graph is one of the most convenient ways to represent a system from
the physical aspect in foreground. It has advantage of putting together
multi-energy domains of a system in a single representation in a
unified manner. The bond graph model of dry friction damper is
simulated on SYMBOLS-shakti® software. In this work, the blades
are modeled as Timoshenko beam. Blade Vibrations under different
working conditions are being analyzed numerically.
Abstract: Laser engraving is a manufacturing method for those applications where previously Electrical Discharge Machining (EDM) was the only choice. Laser engraving technology removes material layer-by-layer and the thickness of layers is usually in the range of few microns. The aim of the present work is to investigate the influence of the process parameters on the surface quality when machined by laser engraving. The examined parameters were: the pulse frequency, the beam speed and the layer thickness. The surface quality was determined by the surface roughness for every set of parameters. Experimental results on Al7075 material showed that the surface roughness strictly depends on the process parameters used.
Abstract: Buildings with floating column are highly undesirable built in seismically active areas. Many urban multi-storey buildings today have floating column buildings which are adopted to accommodate parking at ground floor or reception lobbies in the first storey. The earthquake forces developed at different floor levels in a building need to be brought down along the height to the ground by the shortest path; any deviation or discontinuity in this load transfer path results in poor performance of the building. Floating column buildings are severely damaged during earthquake. Damage on this structure can be reduce by taking the effect of infill wall. This paper presents the effect of stiffness of infill wall to the damage occurred in floating column building when ground shakes. Modelling and analysis are carried out by non linear analysis programme IDARC-2D. Damage occurred in beams, columns, storey are studied by formulating modified Park & Ang model to evaluate damage indices. Overall structural damage indices in buildings due to shaking of ground are also obtained. Dynamic response parameters i.e. lateral floor displacement, storey drift, time period, base shear of buildings are obtained and results are compared with the ordinary moment resisting frame buildings. Formation of cracks, yield, plastic hinge, are also observed during analysis.
Abstract: In this paper comparison of Reflector Antenna
analyzing techniques based on wave and ray nature of optics is
presented for an offset reflector antenna using GRASP (General
Reflector antenna Analysis Software Package) software. The results
obtained using PO (Physical Optics), PTD (Physical theory of
Diffraction), and GTD (Geometrical Theory of Diffraction) are
compared. The validity of PO and GTD techniques in regions around
the antenna, caustic behavior of GTD in main beam, and deviation of
GTD in case of near-in sidelobes of radiation pattern are discussed.
The comparison for far-out sidelobes predicted by PO, PO + PTD
and GTD is described. The effect of Direct Radiations from feed
which results in feed selection for the system is addressed.
Abstract: IPN and IPE sections, which are commonly used European I shapes, are widely used in steel structures as cantilever beams to support overhangs. A considerable number of studies exist on calculating lateral torsional buckling load of I sections. However, most of them provide series solutions or complex closed-form equations. In this paper, a simple equation is presented to calculate lateral torsional buckling load of IPN and IPE section cantilever beams. First, differential equation of lateral torsional buckling is solved numerically for various loading cases. Then a parametric study is conducted on results to present an equation for lateral torsional buckling load of European IPN and IPE beams. Finally, results obtained by presented equation are compared to differential equation solutions and finite element model results. ABAQUS software is utilized to generate finite element models of beams. It is seen that the results obtained from presented equation coincide with differential equation solutions and ABAQUS software results. It can be suggested that presented formula can be safely used to calculate critical lateral torsional buckling load of European IPN and IPE section cantilevers.
Abstract: Quaternary InxAlyGa1-x-yN semiconductors have
attracted much research interest because the use of this quaternary
offer the great flexibility in tailoring their band gap profile while
maintaining their lattice-matching and structural integrity. The
structural and optical properties of InxAlyGa1-x-yN alloys grown by
molecular beam epitaxy (MBE) is presented. The structural quality of
InxAlyGa1-x-yN layers was characterized using high-resolution X-ray
diffraction (HRXRD). The results confirm that the InxAlyGa1-x-yN
films had wurtzite structure and without phase separation. As the In
composition increases, the Bragg angle of the (0002) InxAlyGa1-x-yN
peak gradually decreases, indicating the increase in the lattice constant
c of the alloys. FWHM of (0002) InxAlyGa1-x-yN decreases with
increasing In composition from 0 to 0.04, that could indicate the
decrease of quality of the samples due to point defects leading to
non-uniformity of the epilayers. UV-VIS spectroscopy have been used
to study the energy band gap of InxAlyGa1-x-yN. As the indium (In)
compositions increases, the energy band gap decreases. However, for
InxAlyGa1-x-yN with In composition of 0.1, the band gap shows a
sudden increase in energy. This is probably due to local alloy
compositional fluctuations in the epilayer. The bowing parameter
which appears also to be very sensitive on In content is investigated
and obtained b = 50.08 for quaternary InxAlyGa1-x-yN alloys. From
photoluminescence (PL) measurement, green luminescence (GL)
appears at PL spectrum of InxAlyGa1-x-yN, emitted for all x at ~530 nm
and it become more pronounced as the In composition (x) increased,
which is believed cause by gallium vacancies and related to isolated
native defects.
Abstract: The main objective of this article is to present the semi-active vibration control using an electro-rheological fluid embedded sandwich structure for a cantilever beam. ER fluid is a smart material, which cause the suspended particles polarize and connect each other to form chain. The stiffness and damping coefficients of the ER fluid can be changed in 10 micro seconds; therefore, ERF is suitable to become the material embedded in the tunable vibration absorber to become a smart absorber. For the ERF smart material embedded structure, the fuzzy control law depends on the experimental expert database and the proposed self-tuning strategy. The electric field is controlled by a CRIO embedded system to implement the real application. This study investigates the different performances using the Type-1 fuzzy and interval Type-2 fuzzy controllers. The Interval type-2 fuzzy control is used to improve the modeling uncertainties for this ERF embedded shock absorber. The self-tuning vibration controllers using Type-1 and Interval Type-2 fuzzy law are implemented to the shock absorber system. Based on the resulting performance, Internal Type-2 fuzzy is better than the traditional Type-1 fuzzy control for this vibration control system.
Abstract: We address the problem of joint beamforming and multipath channel parameters estimation in Wideband Code Division Multiple Access (WCDMA) communication systems that employ Multiple-Access Interference (MAI) suppression techniques in the uplink (from mobile to base station). Most of the existing schemes rely on time multiplex a training sequence with the user data. In WCDMA, the channel parameters can also be estimated from a code multiplexed common pilot channel (CPICH) that could be corrupted by strong interference resulting in a bad estimate. In this paper, we present new methods to combine interference suppression together with channel estimation when using multiple receiving antennas by using adaptive signal processing techniques. Computer simulation is used to compare between the proposed methods and the existing conventional estimation techniques.
Abstract: Adopting the measured constitutive relationship of
stress-strain of river ice, the finite element analysis model of
percussive force of river ice and pier is established, by the explicit
dynamical analysis software package LS-DYNA. Effects of element
types, contact method and arithmetic of ice and pier, coupled modes
between different elements, mesh density of pier, and ice sheet in
contact area on the collision force are studied. Some of measures for
the collision force analysis of river ice and pier are proposed as
follows: bridge girder can adopt beam161 element with 3-node; pier
below the line of 1.30m above ice surface and ice sheet use solid164
element with 8-node; in order to accomplish the connection of
different elements, the rigid body with 0.01-0.05m thickness is defined
between solid164 and beam161; the contact type of ice and pier adopts
AUTOMATIC_SURFACE_TO_SURFACE, using symmetrical
penalty function algorithms; meshing size of pier below the line of
1.30m above ice surface should not less than 0.25×0.25×0.5m3. The
simulation results have the advantage of high precision by making a
comparison between measured and computed data. The research
results can be referred for collision force study between river ice and
pier.
Abstract: Concrete pavement has superior durability and longer
structural life than asphalt pavement. Concrete pavement requires
less maintenance compared to asphalt pavement which requires maintenance and major rehabilitation. Use of the concrete pavement
has been grown over the past decade in developing countries. Fibre reinforced concrete (FRC) has been successfully used in design of concrete pavement in past decade. In this research, the effect of fibre
volume fraction in modulus of rupture, load-deflection, equivalent flexural strength (fe,3) and the equivalent flexural strength ratio (Re,3)
has been used in different fibre volume fraction. Crimped-type flat
steel fibre of size 50 x 2.0 x 0.6 mm was used with 1.0%, 1.5% and 2.0% volume fraction. Beam specimens of size 500 x 100 x 100 mm were used for flexural as well as with JCI method for analysis flexural toughness, equivalent flexural strength. It was obtained as the 2% fibre volume fractions; reduce 45% of the concrete pavement
thickness.