Abstract: Introduction: Whole-Body Vibration (WBV) uses
high frequency mechanical stimuli generated by a vibration plate and
transmitted through bone, muscle and connective tissues to the whole
body. Research has shown that long-term vibration-plate training
improves neuromuscular facilitation, especially in afferent neural
pathways, responsible for the conduction of vibration and
proprioceptive stimuli, muscle function, balance and proprioception.
Some researchers suggest that the vibration stimulus briefly inhibits
the conduction of afferent signals from proprioceptors and can
interfere with the maintenance of body balance. The aim of this study
was to evaluate the influence of a single set of exercises associated
with whole-body vibration on the joint position sense and body
balance. Material and methods: The study enrolled 55 people aged
19-24 years. These individuals were randomly divided into a test
group (30 persons) and a control group (25 persons). Both groups
performed the same set of exercises on a vibration plate. The
following vibration parameters: frequency of 20Hz and amplitude of
3mm, were used in the test group. The control group performed
exercises on the vibration plate while it was off. All participants were
instructed to perform six dynamic exercises lasting 30 seconds each
with a 60-second period of rest between them. The exercises involved
large muscle groups of the trunk, pelvis and lower limbs.
Measurements were carried out before and immediately after
exercise. Joint position sense (JPS) was measured in the knee joint
for the starting position at 45° in an open kinematic chain. JPS error
was measured using a digital inclinometer. Balance was assessed in a
standing position with both feet on the ground with the eyes open and
closed (each test lasting 30 sec). Balance was assessed using Matscan
with FootMat 7.0 SAM software. The surface of the ellipse of
confidence and front-back as well as right-left swing were measured
to assess balance. Statistical analysis was performed using Statistica
10.0 PL software. Results: There were no significant differences
between the groups, both before and after the exercise (p> 0.05). JPS
did not change in both the test (10.7° vs. 8.4°) and control groups
(9.0° vs. 8.4°). No significant differences were shown in any of the
test parameters during balance tests with the eyes open or closed in
both the test and control groups (p> 0.05). Conclusions: 1.
Deterioration in proprioception or balance was not observed
immediately after the vibration stimulus. This suggests that vibrationinduced
blockage of proprioceptive stimuli conduction can have only
a short-lasting effect that occurs only as long as a vibration stimulus
is present. 2. Short-term use of vibration in treatment does not impair
proprioception and seems to be safe for patients with proprioceptive
impairment. 3. These results need to be supplemented with an
assessment of proprioception during the application of vibration
stimuli. Additionally, the impact of vibration parameters used in the
exercises should be evaluated.
Abstract: The purposes of hydraulic gate are to maintain the
functions of storing and draining water. It bears long-term hydraulic
pressure and earthquake force and is very important for reservoir and
waterpower plant. The high tensile strength of steel plate is used as
constructional material of hydraulic gate. The cracks and rusts,
induced by the defects of material, bad construction and seismic
excitation and under water respectively, thus, the mechanics
phenomena of gate with crack are probing into the cause of stress
concentration, induced high crack increase rate, affect the safety and
usage of hydroelectric power plant. Stress distribution analysis is a
very important and essential surveying technique to analyze
bi-material and singular point problems. The finite difference
infinitely small element method has been demonstrated, suitable for
analyzing the buckling phenomena of welding seam and steel plate
with crack. Especially, this method can easily analyze the singularity
of kink crack. Nevertheless, the construction form and deformation
shape of some gates are three-dimensional system. Therefore, the
three-dimensional Digital Image Correlation (DIC) has been
developed and applied to analyze the strain variation of steel plate with
crack at weld joint. The proposed Digital image correlation (DIC)
technique is an only non-contact method for measuring the variation of
test object. According to rapid development of digital camera, the cost
of this digital image correlation technique has been reduced.
Otherwise, this DIC method provides with the advantages of widely
practical application of indoor test and field test without the restriction
on the size of test object. Thus, the research purpose of this research is
to develop and apply this technique to monitor mechanics crack
variations of weld steel hydraulic gate and its conformation under
action of loading. The imagines can be picked from real time
monitoring process to analyze the strain change of each loading stage.
The proposed 3-Dimensional digital image correlation method,
developed in the study, is applied to analyze the post-buckling
phenomenon and buckling tendency of welded steel plate with crack.
Then, the stress intensity of 3-dimensional analysis of different
materials and enhanced materials in steel plate has been analyzed in
this paper. The test results show that this proposed three-dimensional
DIC method can precisely detect the crack variation of welded steel
plate under different loading stages. Especially, this proposed DIC
method can detect and identify the crack position and the other flaws
of the welded steel plate that the traditional test methods hardly detect
these kind phenomena. Therefore, this proposed three-dimensional
DIC method can apply to observe the mechanics phenomena of
composite materials subjected to loading and operating.
Abstract: Botanical gardens are very significant organizations
which protect the environment against the increasing environmental
problems, provide environmental education for people, offer
recreation possibilities, etc. This article describes botanical gardens
and their functions. The most important function of botanical garden
is to provide environmental education for people and improve
environmental awareness. Considering this function, some botanical
gardens were examined and opinions were suggested about the
subject.
Abstract: Globally, many women are still disadvantaged when it
comes to business opportunities. Entrepreneurship development
programs, specifically designed to assist women entrepreneurs, are
assisting in solving this problem to a certain extent. The purpose of
this study is to identify the factors that motivate females to start their
own business. Females, from three different groups (2013, 2014 and
2015), who were all enrolled in a short learning program specifically
designed for women in early start-up stage or intending to start a
business, were asked what motivated them to start a business. The
results indicated that, from all three groups, the majority of the
women wanted to start a business to be independent and have
freedom and to add towards a social goal. The results further
indicated that in general, women would enter into entrepreneurship
activity due to pull factors rather than push factors.
Abstract: The education sector is constantly faced with rapid
changes in technologies in terms of ensuring that the curriculum is up
to date and in terms of making sure that students are aware of these
technological changes. This challenge can be seen as the motivation
for this study, which is to examine the factors affecting computing
students’ awareness of the latest Information Technologies (ICTs).
The aim of this study is divided into two sub-objectives which are:
the selection of relevant theories and the design of a conceptual
model to support it as well as the empirical testing of the designed
model. The first objective is achieved by a review of existing
literature on technology adoption theories and models. The second
objective is achieved using a survey of computing students in the four
universities of the KwaZulu-Natal province of South Africa. Data
collected from this survey is analyzed using Statistical package for
the Social Science (SPSS) using descriptive statistics, ANOVA and
Pearson correlations. The main hypothesis of this study is that there is
a relationship between the demographics and the prior conditions of
the computing students and their awareness of general ICT trends and
of Digital Switch Over (DSO) a new technology which involves the
change from analog to digital television broadcasting in order to
achieve improved spectrum efficiency. The prior conditions of the
computing students that were considered in this study are students’
perceived exposure to career guidance and students’ perceived
curriculum currency. The results of this study confirm that gender,
ethnicity, and high school computing course affect students’
perceived curriculum currency while high school location affects
students’ awareness of DSO. The results of this study also confirm
that there is a relationship between students prior conditions and their
awareness of general ICT trends and DSO in particular.
Abstract: The laser-ultrasonic method is realized for
quantifying the influence of porosity on the local Young’s
modulus of isotropic composite materials. The method is based on
a laser thermooptical method of ultrasound generation combined
with measurement of the phase velocity of longitudinal and shear
acoustic waves in samples. The main advantage of this method
compared with traditional ultrasonic research methods is the
efficient generation of short and powerful probing acoustic pulses
required for reliable testing of ultrasound absorbing and
scattering heterogeneous materials. Using as an example samples
of a metal matrix composite with reinforcing microparticles of
silicon carbide in various concentrations, it is shown that to
provide an effective increase in Young’s modulus with increasing
concentration of microparticles, the porosity of the final sample
should not exceed 2%.
Abstract: As computing technology advances, smartphone
applications can assist student learning in a pervasive way. For
example, the idea of using mobile apps for the PA Common Trees,
Pests, Pathogens, in the field as a reference tool allows middle school
students to learn about trees and associated pests/pathogens without
bringing a textbook. While working on the development of three heterogeneous mobile
apps, we ran into numerous challenges. Both the traditional waterfall
model and the more modern agile methodologies failed in practice.
The waterfall model emphasizes the planning of the duration for each
phase. When the duration of each phase is not consistent with the
availability of developers, the waterfall model cannot be employed.
When applying Agile Methodologies, we cannot maintain the high
frequency of the iterative development review process, known as
‘sprints’. In this paper, we discuss the challenges and solutions. We
propose a hybrid model known as the Relay Race Methodology to
reflect the concept of racing and relaying during the process of
software development in practice. Based on the development project,
we observe that the modeling of the relay race transition between any
two phases is manifested naturally. Thus, we claim that the RRM
model can provide a de fecto rather than a de jure basis for the core
concept in the software development model. In this paper, the background of the project is introduced first.
Then, the challenges are pointed out followed by our solutions.
Finally, the experiences learned and the future works are presented.
Abstract: Large-scale machine tools for the manufacturing of
large work pieces, e.g. blades, casings or gears for wind turbines,
feature pose-dependent dynamic behavior. Small structural damping
coefficients lead to long decay times for structural vibrations that
have negative impacts on the production process. Typically, these
vibrations are handled by increasing the stiffness of the structure by
adding mass. This is counterproductive to the needs of sustainable
manufacturing as it leads to higher resource consumption both in
material and in energy. Recent research activities have led to higher
resource efficiency by radical mass reduction that is based on controlintegrated
active vibration avoidance and damping methods. These
control methods depend on information describing the dynamic
behavior of the controlled machine tools in order to tune the
avoidance or reduction method parameters according to the current
state of the machine. This paper presents the appearance, consequences and challenges
of the pose-dependent dynamic behavior of lightweight large-scale
machine tool structures in production. It starts with the theoretical
introduction of the challenges of lightweight machine tool structures
resulting from reduced stiffness. The statement of the pose-dependent
dynamic behavior is corroborated by the results of the experimental
modal analysis of a lightweight test structure. Afterwards, the
consequences of the pose-dependent dynamic behavior of lightweight
machine tool structures for the use of active control and vibration
reduction methods are explained. Based on the state of the art of
pose-dependent dynamic machine tool models and the modal
investigation of an FE-model of the lightweight test structure, the
criteria for a pose-dependent model for use in vibration reduction are
derived. The description of the approach for a general posedependent
model of the dynamic behavior of large lightweight
machine tools that provides the necessary input to the aforementioned
vibration avoidance and reduction methods to properly tackle
machine vibrations is the outlook of the paper.
Abstract: This study presents experimental and optimization of
nanoparticle mass concentration and heat input based on the total
thermal resistance (Rth) of loop heat pipe (LHP), employed for PCCPU
cooling. In this study, silica nanoparticles (SiO2) in water with
particle mass concentration ranged from 0% (pure water) to 1% is
considered as the working fluid within the LHP. The experimental
design and optimization is accomplished by the design of
experimental tool, Response Surface Methodology (RSM). The
results show that the nanoparticle mass concentration and the heat
input have significant effect on the Rth of LHP. For a given heat
input, the Rth is found to decrease with the increase of the
nanoparticle mass concentration up to 0.5% and increased thereafter.
It is also found that the Rth is decreased when the heat input is
increased from 20W to 60W. The results are optimized with the
objective of minimizing the Rth, using Design-Expert software, and
the optimized nanoparticle mass concentration and heat input are
0.48% and 59.97W, respectively, the minimum thermal resistance
being 2.66 (ºC/W).
Abstract: Excessive fretting wear at the taper-trunnion junction
(trunnionosis) apparently contributes to the high failure rates of hip
implants. Implant wear and corrosion lead to the release of metal
particulate debris and subsequent release of metal ions at the tapertrunnion
surface. This results in a type of metal poisoning referred to
as metallosis. The consequences of metal poisoning include;
osteolysis (bone loss), osteoarthritis (pain), aseptic loosening of the
prosthesis and revision surgery. Follow up after revision surgery,
metal debris particles are commonly found in numerous locations. Background: A stable connection between the femoral ball head
(taper) and stem (trunnion) is necessary to prevent relative motions
and corrosion at the taper junction. Hence, the importance of
component assembly cannot be over-emphasized. Therefore, the aim
of this study is to determine the influence of head-stem junction
assembly by press fitting and the subsequent
disengagement/disassembly on the connection strength between the
taper ball head and stem. Methods: CoCr femoral heads were assembled with High stainless
hydrogen steel stem (trunnion) by Push-in i.e. press fit; and
disengaged by pull-out test. The strength and stability of the two
connections were evaluated by measuring the head pull-out forces
according to ISO 7206-10 standards. Findings: The head-stem junction strength linearly increases with
assembly forces.
Abstract: Novel wind-lens turbine designs can augment power
output. Vacuum-Assisted Resin Transfer Molding (VARTM) is used
to form large and complex structures from a Carbon Fiber Reinforced
Polymer (CFRP) composite. Typically, wind-lens turbine structures
are fabricated in segments, and then bonded to form the final structure.
This paper introduces five new adhesive joints, divided into two
groups: one is constructed between dry carbon and CFRP fabrics, and
the other is constructed with two dry carbon fibers. All joints and
CFRP fabrics were made in our laboratory using VARTM
manufacturing techniques. Specimens were prepared for tensile testing
to measure joint performance. The results showed that the second
group of joints achieved a higher tensile strength than the first group.
On the other hand, the tensile fracture behavior of the two groups
showed the same pattern of crack originating near the joint ends
followed by crack propagation until fracture.
Abstract: Well logging records can help to answer many
questions from a wide range of special interested information and
basic petrophysical properties to formation evaluation of oil and gas
reservoirs. The accurate calculations of porosity in carbonate
reservoirs are the most challenging aspects of the well logging
analysis. Many equations have been developed over the years based
on known physical principles or on empirically derived relationships,
which are used to calculate porosity, estimate lithology, and water
saturation; however these parameters are calculated from well logs by
using modern technique in a current study. Nasiriya oil field is one of
the giant oilfields in the Middle East, and the formation under study
is the Mishrif carbonate formation which is the shallowest
hydrocarbon bearing zone in this oilfield. Neurolog software was
used to digitize the scanned copies of the available logs.
Environmental corrections had been made as per Schlumberger charts
2005, which supplied in the Interactive Petrophysics software. Three
saturation models have been used to calculate water saturation of
carbonate formations, which are simple Archie equation, Dual water
model, and Indonesia model. Results indicate that the Mishrif
formation consists mainly of limestone, some dolomite, and shale.
The porosity interpretation shows that the logging tools have a good
quality after making the environmental corrections. The average
formation water saturation for Mishrif formation is around 0.4-
0.6.This study is provided accurate behavior of petrophysical
properties with depth for this formation by using modern software.
Abstract: Non-linear dynamic time history analysis is
considered as the most advanced and comprehensive analytical
method for evaluating the seismic response and performance of
multi-degree-of-freedom building structures under the influence of
earthquake ground motions. However, effective and accurate
application of the method requires the implementation of advanced
hysteretic constitutive models of the various structural components
including masonry infill panels. Sophisticated computational research
tools that incorporate realistic hysteresis models for non-linear
dynamic time-history analysis are not popular among the professional
engineers as they are not only difficult to access but also complex and
time-consuming to use. In addition, commercial computer programs
for structural analysis and design that are acceptable to practicing
engineers do not generally integrate advanced hysteretic models
which can accurately simulate the hysteresis behavior of structural
elements with a realistic representation of strength degradation,
stiffness deterioration, energy dissipation and ‘pinching’ under cyclic
load reversals in the inelastic range of behavior. In this scenario,
push-over or non-linear static analysis methods have gained
significant popularity, as they can be employed to assess the seismic
performance of building structures while avoiding the complexities
and difficulties associated with non-linear dynamic time-history
analysis. “Push-over” or non-linear static analysis offers a practical
and efficient alternative to non-linear dynamic time-history analysis
for rationally evaluating the seismic demands. The present paper is
based on the analytical investigation of the effect of distribution of
masonry infill panels over the elevation of planar masonry infilled
reinforced concrete [R/C] frames on the seismic demands using the
capacity spectrum procedures implementing nonlinear static analysis
[pushover analysis] in conjunction with the response spectrum
concept. An important objective of the present study is to numerically
evaluate the adequacy of the capacity spectrum method using
pushover analysis for performance based design of masonry infilled
R/C frames for near-field earthquake ground motions.
Abstract: This paper addresses the problem of offline path
planning for Unmanned Aerial Vehicles (UAVs) in complex threedimensional
environment with obstacles, which is modelled by 3D
Cartesian grid system. Path planning for UAVs require the
computational intelligence methods to move aerial vehicles along the
flight path effectively to target while avoiding obstacles. In this paper
Modified Particle Swarm Optimization (MPSO) algorithm is applied
to generate the optimal collision free 3D flight path for UAV. The
simulations results clearly demonstrate effectiveness of the proposed
algorithm in guiding UAV to the final destination by providing
optimal feasible path quickly and effectively.
Abstract: Paper deals with the modeling and simulation of energy consumption and GHG production of two different modes of regional passenger transport – road and railway. These two transport modes use the same type of fuel – diesel. Modeling and simulation of the energy consumption in transport is often used due to calculation satisfactory accuracy and cost efficiency. Paper deals with the calculation based on EN standards and information collected from technical information from vehicle producers and characteristics of tracks. Calculation included maximal theoretical capacity of bus and train and real passenger’s measurement from operation. Final energy consumption and GHG production is calculated by using software simulation. In evaluation of the simulation is used system “well to wheel”.
Abstract: The paper is focused to the evaluation railway tracks
in the Slovakia by using Multi-Criteria method. Evaluation of railway
tracks has important impacts for the assessment of investment in
technical equipment. Evaluation of railway tracks also has an
important impact for the allocation of marshalling yards. Marshalling
yards are in transport model as centers for the operation assigned
catchment area. This model is one of the effective ways to meet the
development strategy of the European Community's railways. By
applying this model in practice, a transport company can guarantee a
higher quality of service and then expect an increase in performance.
The model is also applicable to other rail networks. This model
supplements a theoretical problem of train formation problem of new
ways of looking at evaluation of factors affecting the organization of
wagon flows.
Abstract: The article includes the results and conclusions from
empirical researches that had been done. The research focuses on the
impact of investments made in small and medium-sized enterprises
financed from EU funds on the competitiveness of these companies.
The researches includes financial results in sales revenue and net
income, expenses, and many other new products/services on offer,
higher quality products and services, more modern methods of
production, innovation in management processes, increase in the
number of customers, increase in market share, increase in
profitability of production and provision of services. The main
conclusions are that, companies with direct investments under this
measure shall apply the modern methods of production. The
consequence of this is to increase the quality of our products and
services. Furthermore, both small and medium-sized enterprises have
introduced new products and services. Investments were carried out,
thus enabling better work organization in enterprises. Entrepreneurs
would guarantee higher quality of service, which would result in
better relationships with their customers, what is more, noting the rise
in number of clients. More than half of the companies indicated that
the investments contributed to the increase in market share. Same
thing as for market reach and brand recognition of particular
company. An interesting finding is that, investments in small
enterprises were more effective than medium-sized enterprises.
Abstract: Polymorphism is one of the main pillars of objectoriented
paradigm. It induces hidden forms of class dependencies
which may impact software quality, resulting in higher cost factor for
comprehending, debugging, testing, and maintaining the software. In
this paper, a new cognitive complexity metric called Cognitive
Weighted Polymorphism Factor (CWPF) is proposed. Apart from the
software structural complexity, it includes the cognitive complexity
on the basis of type. The cognitive weights are calibrated based on 27
empirical studies with 120 persons. A case study and experimentation
of the new software metric shows positive results. Further, a
comparative study is made and the correlation test has proved that
CWPF complexity metric is a better, more comprehensive, and more
realistic indicator of the software complexity than Abreu’s
Polymorphism Factor (PF) complexity metric.
Abstract: Brain-Computer Interfaces (BCIs) measure brain
signals activity, intentionally and unintentionally induced by users,
and provides a communication channel without depending on the
brain’s normal peripheral nerves and muscles output pathway.
Feature Selection (FS) is a global optimization machine learning
problem that reduces features, removes irrelevant and noisy data
resulting in acceptable recognition accuracy. It is a vital step
affecting pattern recognition system performance. This study presents
a new Binary Particle Swarm Optimization (BPSO) based feature
selection algorithm. Multi-layer Perceptron Neural Network
(MLPNN) classifier with backpropagation training algorithm and
Levenberg-Marquardt training algorithm classify selected features.
Abstract: This investigation is focused on using of Mon dance
in Pathum Thani Province’s tradition and has the following
objectives: 1) to study the background of Mon dance in Pathum
Thani Province; 2) to study Mon dance in Pathum Thani Province;
and 3) to study of using Mon dance in Pathum Thani province’s
tradition. This qualitative research was conducted in Pathum Thani
province (in the central of Thailand). Data was collected from
documentary study and field data by means of observation, interview,
and group discussion. Workshops were also held with a total of 100
attendees, comprised of 20 key informants, 40 casual informants and
40 general informants. Data was validated using the triangulation
technique and the findings are presented using the descriptive
analysis. The results of the study show that the historical background
of Mon dance in Pathum Thani Province initiated during the war
evacuation from Martaban (south of Burma) to settle down in Sam
Khok, Pathum Thani Province in Ayutthaya period to Rattanakosin.
The study found that Mon dance typically consists of 12-13 dancing
process. The melodies have 12-13 songs. Piphat Mon (Mon
traditional music ensemble) is used in the performance. Performers
are dressed in Mon traditional costumes. The performers are 6-12
women and depending on the employer’s demands. Length of the
performance varies from the duration of music orchestration. Rituals
and customs performed are paying homage to teachers before the
performance. The offerings are composed of flowers, incense sticks,
candles, money gifts which are well arranged on a tray with pedestal,
and also liquors, tobaccos and pure water for asking propitiousness.
For the use of Mon dance in Pathum Thani Province’s tradition, it is
found that the dance is commonly performed in the funeral
ceremonial tradition at present because the physical postures of the
performance are considered graceful and exquisite. In addition, as for
its value, it has long been believed since the ancient times that Mon
dance was a sacred thing considered as the dignity and glorification
especially for funeral ceremonies of priest or royal hierarchy classes.
However, Mon dance has continued to be used in the traditions
associated with Mon people activities in Pathum Thani Province for
instance customary welcome for honor guest and Songkran festival.