Abstract: The article presents test results on the changes
occurring in sewage sludge during the process of its storage. Tests
were conducted on mechanically dehydrated sewage sludge derived
from large municipal sewage treatment plants equipped with
biological sewage treatment systems. In testing presented in the paper
the focus was on the basic fuel properties of sewage sludge: moisture
content, heat of combustion, carbon share. In the first part of the
article the overview of the issues concerning the sewage sludge
management is presented and the genesis of tests is explained.
Further in the paper, selected results of conducted tests are discussed.
Changes in tested parameters were determined in the period of a 10-
month sewage storage.
Abstract: In this paper, we propose a novel algorithm for
delineating the endocardial wall from a human heart ultrasound scan.
We assume that the gray levels in the ultrasound images are
independent and identically distributed random variables with
different Rician Inverse Gaussian (RiIG) distributions. Both synthetic
and real clinical data will be used for testing the algorithm. Algorithm
performance will be evaluated using the expert radiologist evaluation
of a soft copy of an ultrasound scan during the scanning process and
secondly, doctor’s conclusion after going through a printed copy of
the same scan. Successful implementation of this algorithm should
make it possible to differentiate normal from abnormal soft tissue and
help disease identification, what stage the disease is in and how best
to treat the patient. We hope that an automated system that uses this
algorithm will be useful in public hospitals especially in Third World
countries where problems such as shortage of skilled radiologists and
shortage of ultrasound machines are common. These public hospitals
are usually the first and last stop for most patients in these countries.
Abstract: This paper presents a remote on-line diagnostic system
for vehicles via the use of On-Board Diagnostic (OBD), GPS, and 3G
techniques. The main parts of the proposed system are on-board
computer, vehicle monitor server, and vehicle status browser. First,
the on-board computer can obtain the location of deriver and vehicle
status from GPS receiver and OBD interface, respectively. Then
on-board computer will connect with the vehicle monitor server
through 3G network to transmit the real time vehicle system status.
Finally, vehicle status browser could show the remote vehicle status
including vehicle speed, engine rpm, battery voltage, engine coolant
temperature, and diagnostic trouble codes. According to the
experimental results, the proposed system can help fleet managers and
car knockers to understand the remote vehicle status. Therefore this
system can decrease the time of fleet management and vehicle repair
due to the fleet managers and car knockers who find the diagnostic
trouble messages in time.
Abstract: Monitoring the tool flank wear without affecting the
throughput is considered as the prudent method in production
technology. The examination has to be done without affecting the
machining process. In this paper we proposed a novel work that is
used to determine tool flank wear by observing the sound signals
emitted during the turning process. The work-piece material we used
here is steel and aluminum and the cutting insert was carbide
material. Two different cutting speeds were used in this work. The
feed rate and the cutting depth were constant whereas the flank wear
was a variable. The emitted sound signal of a fresh tool (0 mm flank
wear) a slightly worn tool (0.2 -0.25 mm flank wear) and a severely
worn tool (0.4mm and above flank wear) during turning process were
recorded separately using a high sensitive microphone. Analysis
using Singular Value Decomposition was done on these sound
signals to extract the feature sound components. Observation of the
results showed that an increase in tool flank wear correlates with an
increase in the values of SVD features produced out of the sound
signals for both the materials. Hence it can be concluded that wear
monitoring of tool flank during turning process using SVD features
with the Fuzzy C means classification on the emitted sound signal is
a potential and relatively simple method.
Abstract: Forecasting the values of the indicators, which
characterize the effectiveness of performance of organizations is of
great importance for their successful development. Such forecasting
is necessary in order to assess the current state and to foresee future
developments, so that measures to improve the organization-s
activity could be undertaken in time. The article presents an
overview of the applied mathematical and statistical methods for
developing forecasts. Special attention is paid to artificial neural
networks as a forecasting tool. Their strengths and weaknesses are
analyzed and a synopsis is made of the application of artificial neural
networks in the field of forecasting of the values of different
education efficiency indicators. A method of evaluation of the
activity of universities using the Balanced Scorecard is proposed and
Key Performance Indicators for assessment of e-learning are
selected. Resulting indicators for the evaluation of efficiency of the
activity are proposed. An artificial neural network is constructed and
applied in the forecasting of the values of indicators for e-learning
efficiency on the basis of the KPI values.
Abstract: This paper aims at to develop a robust optimization methodology for the mechatronic modules of machine tools by considering all important characteristics from all structural and control domains in one single process. The relationship between these two domains is strongly coupled. In order to reduce the disturbance caused by parameters in either one, the mechanical and controller design domains need to be integrated. Therefore, the concurrent integrated design method Design For Control (DFC), will be employed in this paper. In this connect, it is not only applied to achieve minimal power consumption but also enhance structural performance and system response at same time. To investigate the method for integrated optimization, a mechatronic feed drive system of the machine tools is used as a design platform. Pro/Engineer and AnSys are first used to build the 3D model to analyze and design structure parameters such as elastic deformation, nature frequency and component size, based on their effects and sensitivities to the structure. In addition, the robust controller,based on Quantitative Feedback Theory (QFT), will be applied to determine proper control parameters for the controller. Therefore, overall physical properties of the machine tool will be obtained in the initial stage. Finally, the technology of design for control will be carried out to modify the structural and control parameters to achieve overall system performance. Hence, the corresponding productivity is expected to be greatly improved.
Abstract: The objective of the research was to evaluate the
quality of milk pomade sweet – sherbet packed in different packaging
materials (Multibarrier 60, met.BOPET/PE, Aluthen), by several
packaging technologies – active and modified atmosphere (MAP)
(consisting of 100% CO2), and control – in air ambiance.
Experiments were carried out at the Faculty of Food Technology of
Latvia University of Agriculture. Samples were stored at the room
temperature +21±1 °C. The physiochemical properties – weight
losses, moisture, hardening, colour and changes in headspace
atmosphere concentration (CO2 and O2) of packs were analysed
before packaging and after 2, 4, 6, 8, 10 and 12 storage weeks.
Abstract: Abrasive waterjet is a novel machining process capable of processing wide range of hard-to-machine materials. This research addresses modeling and optimization of the process parameters for this machining technique. To model the process a set of experimental data has been used to evaluate the effects of various parameter settings in cutting 6063-T6 aluminum alloy. The process variables considered here include nozzle diameter, jet traverse rate, jet pressure and abrasive flow rate. Depth of cut, as one of the most important output characteristics, has been evaluated based on different parameter settings. The Taguchi method and regression modeling are used in order to establish the relationships between input and output parameters. The adequacy of the model is evaluated using analysis of variance (ANOVA) technique. The pairwise effects of process parameters settings on process response outputs are also shown graphically. The proposed model is then embedded into a Simulated Annealing algorithm to optimize the process parameters. The optimization is carried out for any desired values of depth of cut. The objective is to determine proper levels of process parameters in order to obtain a certain level of depth of cut. Computational results demonstrate that the proposed solution procedure is quite effective in solving such multi-variable problems.
Abstract: This paper demonstrates a model of an e-Learning
system based on nowadays learning theory and distant education
practice. The relationships in the model are designed to be simple
and functional and do not necessarily represent any particular e-
Learning environments. It is meant to be a generic e-Learning
system model with implications for any distant education course
instructional design. It allows online instructors to move away from
the discrepancy between the courses and body of knowledge. The
interrelationships of four primary sectors that are at the e-Learning
system are presented in this paper. This integrated model includes
[1] pedagogy, [2] technology, [3] teaching, and [4] learning. There
are interactions within each of these sectors depicted by system loop
map.
Abstract: Technology assessment is a vital part of decision process in manufacturing, particularly for decisions on selection of new sustainable manufacturing processes. To assess these processes, a matrix approach is introduced and sustainability assessment models are developed. Case studies show that the matrix-based approach provides a flexible and practical way for sustainability evaluation of new manufacturing technologies such as those used in surface coating. The technology assessment of coating processes reveals that compared with powder coating, the sol-gel coating can deliver better technical, economical and environmental sustainability with respect to the selected sustainability evaluation criteria for a decorative coating application of car wheels.
Abstract: A Laboratory-scale packed bed reactor with microbial
cellulose as the biofilm carrier was used to investigate the
denitrification of high-strength nitrate wastewater with specific
emphasis on the effect the nitrogen loading rate and hydraulic
retention time. Ethanol was added as a carbon source for
denitrification. As a result of this investigation, it was found that up
to 500 mg/l feed nitrate concentration the present system is able to
produce an effluent with nitrate content below 10 ppm at 3 h
hydraulic retention time. The highest observed denitrification rate
was 4.57 kg NO3-N/ (m3 .d) at a nitrate load of 5.64 kg NO3-
N/(m3 .d), and removal efficiencies higher than 90% were obtained
for loads up to 4.2 kg NO3-N/(m3 .d). A mass relation between COD
consumed and NO3-N removed around 2.82 was observed. This
continuous-flow bioreactor proved an efficient denitrification system
with a relatively low retention time.
Abstract: One of the major disadvantages of the minimally
invasive surgery (MIS) is the lack of tactile feedback to the surgeon.
In order to identify and avoid any damage to the grasped complex
tissue by endoscopic graspers, it is important to measure the local
softness of tissue during MIS. One way to display the measured
softness to the surgeon is a graphical method. In this paper, a new
tactile sensor has been reported. The tactile sensor consists of an
array of four softness sensors, which are integrated into the jaws of a
modified commercial endoscopic grasper. Each individual softness
sensor consists of two piezoelectric polymer Polyvinylidene Fluoride
(PVDF) films, which are positioned below a rigid and a compliant
cylinder. The compliant cylinder is fabricated using a micro molding
technique. The combination of output voltages from PVDF films is
used to determine the softness of the grasped object. The theoretical
analysis of the sensor is also presented.
A method has been developed with the aim of reproducing the
tactile softness to the surgeon by using a graphical method. In this
approach, the proposed system, including the interfacing and the data
acquisition card, receives signals from the array of softness sensors.
After the signals are processed, the tactile information is displayed
by means of a color coding method. It is shown that the degrees of
softness of the grasped objects/tissues can be visually differentiated
and displayed on a monitor.
Abstract: Dynamic shear test on simulated phantom can be used
to validate magnetic resonance elastography (MRE) measurements.
Phantom gel has been usually utilized for the cell culture of cartilage
and soft tissue and also been used for mechanical property
characterization using imaging systems. The viscoelastic property of
the phantom would be important for dynamic experiments and
analyses. In this study, An axisymmetric FE model is presented for
determining the dynamic shear behaviour of brain simulated phantom
using ABAQUS. The main objective of this study was to investigate
the effect of excitation frequencies and boundary conditions on shear
modulus and shear viscosity in viscoelastic media.
Abstract: Field Association (FA) terms are a limited set of discriminating terms that give us the knowledge to identify document fields which are effective in document classification, similar file retrieval and passage retrieval. But the problem lies in the lack of an effective method to extract automatically relevant Arabic FA Terms to build a comprehensive dictionary. Moreover, all previous studies are based on FA terms in English and Japanese, and the extension of FA terms to other language such Arabic could be definitely strengthen further researches. This paper presents a new method to extract, Arabic FA Terms from domain-specific corpora using part-of-speech (POS) pattern rules and corpora comparison. Experimental evaluation is carried out for 14 different fields using 251 MB of domain-specific corpora obtained from Arabic Wikipedia dumps and Alhyah news selected average of 2,825 FA Terms (single and compound) per field. From the experimental results, recall and precision are 84% and 79% respectively. Therefore, this method selects higher number of relevant Arabic FA Terms at high precision and recall.
Abstract: The purpose of study was to design and construction
the semi-automatic sliced ginger machine for reduce production times
in sheet and slice ginger procedure furthermore, reduced amount of
labor of slides and cutting method. Take consider into clean and safety of workers and consumers. The principle of machines, used 1
horsepower motor, rotation speed of sliced blade 967 rpm, the diameter of sliced dish 310 mm, consists of 2 blades for sheet cutting
ginger and the power from motor which transfer to rotate the sliced blade roller, rotation speed 440 rpm. The slice cutter roller was sliced
ginger from sheet ginger to line ginger. The conveyer could
adjustment level of motors, used to the beginning area that sheet
ginger was transference to the roller for sheet and sliced cutting in next process. The cover of sliced cutting had channel for 1 tuber of
ginger. The semi-automatic sliced ginger machine could produced sheet ginger 81.8 kg/h (6.2 times of labor) and line ginger 17.9 kg/h
(2.5 times of labor) compare with, labor work could produced sheet
ginger 13.2 kg/h and line ginger 7.1 kg/h, and when timekeeper, the
total times of semi auto machine 30.86 kg/h and labor 4.6 kg/h, there
for the semi auto machine was 6.7 times of labor. The semiautomatic
sliced ginger machine convenient, easy for use and
maintain, in addition to reduce fatigue of body and seriousness from
works; must be used high skill, and protection accident in slicing
procedure. Beside, machine could used with other vegetables for
example potato, carrot .etc
Abstract: The present project was conducted with the
circumferential-fuel-jets inverse diffusion flame (CIDF) burner
burning liquefied petroleum gas (LPG) enriched with 50% of
hydrogen fuel (H2). The range of stable operation of the CIDF burner
in terms of Reynolds number (from laminar to turbulent flow regions),
equivalence ratio and fuel jet velocity of LPG of the 50% H2-LPG
mixed fuel was identified. Experiments were also carried out to
investigate the flame structures of the LPG flame and LPG enriched H2
flame. Experimental results obtained from these two flames were
compared to fully explore the influence of hydrogen addition on flame
stability. Flame heights obtained by burning these two kinds of fuels at
various equivalence ratios were compared and correlated with the
Global Momentum Ratio (GMR).
Abstract: Investigations of the unimolecular decomposition of
vinyl ethyl ether (VEE), vinyl propyl ether (VPE) and vinyl butyl
ether (VBE) have shown that activation of the molecule of a ether
results in formation of a cyclic construction - the transition state (TS),
which may lead to the displacement of the thermodynamic
equilibrium towards the reaction products. The TS is obtained by
applying energy minimization relative to the ground state of an ether
under the program MM2 when taking into account the hydrogen bond
formation between a hydrogen atom of alkyl residue and the extreme
atom of carbon of the vinyl group. The dissociation of TS up to the
products is studied by energy minimization procedure using the
mathematical program Gaussian. The obtained calculation data for
VEE testify that the decomposition of this ether may be conditioned
by hydrogen bond formation for two possible versions: when α- or β-
hydrogen atoms of the ethyl group are bound to carbon atom of the
vinyl group. Applying the same calculation methods to other ethers
(VPE and VBE) it is shown that only in the case of hydrogen bonding
between α-hydrogen atom of the alkyl residue and the extreme atom
of carbon of the vinyl group (αH---C) results in decay of theses
ethers.
Abstract: Indium-tin oxide films are deposited by low plasma
temperature RF sputtering on highly flexible modification of glycol
polyethyleneterephtalate substrates. The produced layers are
characterized with transparency over 82 % and sheet resistance of
86.9 Ω/square. The film’s conductivity was further improved by
additional UV illumination from light source (365 nm), having power
of 250 W. The influence of the UV exposure dose on the structural
and electro-optical properties of ITO was investigated. It was
established that the optimum time of illumination is 10 minutes and
further UV treatment leads to polymer substrates degradation.
Structural and bonds type analysis show that at longer treatment
carbon atoms release and diffuse into ITO films, which worsen their
electrical behavior. For the optimum UV dose the minimum sheet
resistance was measured to be 19.2 Ω/square, and the maximum
transparency remained almost unchanged – above 82 %.
Abstract: The storage of thermal energy as a latent heat of phase
change material (PCM) has created considerable interest among
researchers in recent times. Here, an attempt is made to carry out
numerical investigations to analyze the performance of latent heat
storage units (LHSU) employing phase change material. The
mathematical model developed is based on an enthalpy formulation.
Freezing time of PCM packed in three different shaped containers
viz. rectangular, cylindrical and cylindrical shell is compared. The
model is validated with the results available in the literature. Results
show that for the same mass of PCM and surface area of heat
transfer, cylindrical shell container takes the least time for freezing
the PCM and this geometric effect is more pronounced with an
increase in the thickness of the shell than that of length of the shell.
Abstract: This paper presents a new heuristic algorithm for the classical symmetric traveling salesman problem (TSP). The idea of the algorithm is to cut a TSP tour into overlapped blocks and then each block is improved separately. It is conjectured that the chance of improving a good solution by moving a node to a position far away from its original one is small. By doing intensive search in each block, it is possible to further improve a TSP tour that cannot be improved by other local search methods. To test the performance of the proposed algorithm, computational experiments are carried out based on benchmark problem instances. The computational results show that algorithm proposed in this paper is efficient for solving the TSPs.