Abstract: Among various active filters, shunt active filter is a
viable solution for reactive power and harmonics compensation. In
this paper, the SRF plan is used to generate current reference for
compensation and conventional PI controllers were used as the
controller to compensate the reactive power. The design of the closed
loop controllers is reserved simple by modeling them as first order
systems. Computationally uncomplicated and efficient SVM system
is used in the present work for better utilization of dc bus voltage.
The rating of shunt active filter has been finalized based on the
reactive power demand of the selected reactive load. The proposed
control and SVM technique are validated by simulating in MATLAB
software.
Abstract: WO3/SiO2 catalysts were modified by an ion exchange
method with sodium hydroxide or potassium hydroxide solution. The
performance of the modified catalysts was tested in the metathesis of
ethylene and trans-2-butene to propylene. During ion exchange,
sodium and potassium ions played different roles. Sodium modified
catalysts revealed constant trans-2-butene conversion and propylene
selectivity when the concentrations of sodium in the solution were
varied. In contrast, potassium modified catalysts showed reduction of
the conversion and increase of the selectivity. From these results,
potassium hydroxide may affect the transformation of tungsten oxide
active species, resulting in the decrease in conversion whereas
sodium hydroxide did not. Moreover, the modification of catalysts by
this method improved the catalyst stability by lowering the amount of
coke deposited on the catalyst surface.
Abstract: The 5th generation of mobile networks is term used in
various research papers and projects to identify the next major phase
of mobile telecommunications standards. 5G wireless networks will
support higher peak data rate, lower latency and provide best
connections with QoS guarantees.
In this article, we discuss various promising technologies for 5G
wireless communication systems, such as IPv6 support, World Wide
Wireless Web (WWWW), Dynamic Adhoc Wireless Networks
(DAWN), BEAM DIVISION MULTIPLE ACCESS (BDMA), Cloud
Computing, cognitive radio technology and FBMC/OQAM.
This paper is organized as follows: First, we will give introduction
to 5G systems, present some goals and requirements of 5G. In the
next, basic differences between 4G and 5G are given, after we talk
about key technology innovations of 5G systems and finally we will
conclude in last Section.
Abstract: For the music composer Myriam Marbe the musical
time and memory represent 2 (complementary) phenomena with
conclusive impact on the settlement of new musical ontologies.
Summarizing the most important achievements of the contemporary
techniques of composition, her vision on the microform presented in
The Concert for Daniel Kientzy, saxophone and orchestra transcends
the linear and unidirectional time in favour of a flexible, multivectorial
speech with spiral developments, where the sound substance
is auto(re)generated by analogy with the fundamental processes of
the memory. The conceptual model is of an archetypal essence, the
music composer being concerned with identifying the mechanisms of
the creation process, especially of those specific to the collective
creation (of oral tradition). Hence the spontaneity of expression,
improvisation tint, free rhythm, micro-interval intonation, coloristictimbral
universe dominated by multiphonics and unique sound
effects, hence the atmosphere of ritual, however purged by the
primary connotations and reprojected into a wonderful spectacular
space. The Concert is a work of artistic maturity and enforces respect,
among others, by the timbral diversity of the three species of
saxophone required by the music composer (baritone, sopranino and
alt), in Part III Daniel Kientzy shows the performance of playing two
saxophones concomitantly. The score of the music composer Myriam
Marbe contains a deeply spiritualized music, full or archetypal
symbols, a music whose drama suggests a real cinematographic
movement.
Abstract: We present a gas-liquid microfluidic system as a
reactor to obtain magnetite nanoparticles with an excellent degree of
control regarding their crystalline phase, shape and size. Several
types of microflow approaches were selected to prevent nanomaterial
aggregation and to promote homogenous size distribution. The
selected reactor consists of a mixer stage aided by ultrasound waves
and a reaction stage using a N2-liquid segmented flow to prevent
magnetite oxidation to non-magnetic phases. A milli-fluidic reactor
was developed to increase the production rate where a magnetite
throughput close to 450 mg/h in a continuous fashion was obtained.
Abstract: Masonry infill walls are inevitable in the selfsupporting
structures, but their contribution in the resistance to
earthquake loads is generally neglected in the structural analyses. The
principal aim of this work through a numerical study of masonry
infill walls behavior in structures subjected to horizontal load is to
propose by finite elements numerical modeling, a more reliable
approach, faster and close to reality. In this study, 3D Finite Element
Analysis was developed to study the behavior of masonry infill walls
in structures subjected to horizontal load; the finite element software
being used was ABAQUS, it is observed that more rigidity of the
masonry filling is significant, more the structure is rigid, we can so
conclude that the filling brings an additional rigidity to the structure
not to be neglected; it is also observed that when the framework is
subjected to horizontal loads, the framework separates from the
filling on the level of the tended diagonal.
Abstract: This study focuses on a novel method for dispersion
and distribution of reinforcement under high intensive shear stress to
produce metal composites. The polyacrylonitrile (PAN)-based short
carbon fiber (Csf) and Nextel 610 alumina fiber were dispersed under
high intensive shearing at mushy zone in semi-solid of A356 by a
novel method. The bundles and clusters were embedded by
infiltration of slurry into the clusters, thus leading to a uniform
microstructure. The fibers were embedded homogenously into the
aluminum around 576-580°C with around 46% of solid fraction.
Other experiments at 615°C and 568°C which are contained 0% and
90% solid respectively were not successful for dispersion and
infiltration of aluminum into bundles of Csf. The alumina fiber has
been cracked by high shearing load. The morphologies and
crystalline phase were evaluated by SEM and XRD. The adopted
thixo-process effectively improved the adherence and distribution of
Csf into Al that can be developed to produce various composites by
thixomixing.
Abstract: Microbes have been used to solve environmental
problems for many years. The role of microorganism to sequester,
precipitate or alter the oxidation state of various heavy metals has
been extensively studied. Treatment using microorganism interacts
with toxic metal are very diverse. The purpose of this research is to
remove the mercury using Pseudomonas putida (P. putida), pure
culture ATTC 49128 at optimum growth parameters such as
techniques of culture, acclimatization time and speed of incubator
shaker. Thus, in this study, the optimum growth parameters of P.
putida were obtained to achieve the maximum of mercury removal.
Based on the optimum parameters of P. putida for specific growth
rate, the removal of two different mercury concentration, 1 ppm and
4 ppm were studied. From mercury nitrate solution, a mercuryresistant
bacterial strain which is able to reduce from ionic mercury
to metallic mercury was used to reduce ionic mercury. The overall
levels of mercury removal in this study were between 80% and 89%.
The information obtained in this study is of fundamental for
understanding of the survival of P. putida ATTC 49128 in mercury
solution. Thus, microbial mercury removal is a potential
bioremediation for wastewater especially in petrochemical industries
in Malaysia.
Abstract: In contrast with literal meaning of nano, researchers
have been achieved mega adventures in this area and every day more
nanomaterials are being introduced to the market. After long time
application of fossil-based plastics, nowadays accumulation of their
waste seems to be a big problem to the environment. On the other
hand, mankind has more attention to safety and living environment.
Replacing common plastic packaging materials with degradable ones
that degrade faster and convert to non-dangerous components like
water and carbon dioxide have more attractions; these new materials
are based on renewable and inexpensive sources of starch and
cellulose. However, the functional properties of them do not suitable
for packaging. At this point, nanotechnology has an important role.
Utilizing of nanomaterials in polymer structure will improve
mechanical and physical properties of them; nanocrystalline cellulose
(NCC) has this ability. This work has employed a chemical method to
produce NCC and starch bio nanocomposite containing NCC. X-Ray
Diffraction technique has characterized the obtained materials.
Results showed that applied method is a suitable one as well as
applicable one to NCC production.
Abstract: Five palm oil ether monoesters utilized as novel
biodiesels were synthesized and structurally identified in the paper.
The investigation was made on the effect of ether species on
physicochemical properties of the palm oil ether monoesters. The
results showed that density, kinematic viscosity, smoke point, and
solidifying point increase linearly with their –CH2 group number in
certain relationships. Cetane number is enhanced whereas heat value
decreases linearly with –CH2 group number. In addition, the
influencing regularities of the volumetric content of the palm oil ether
monoesters on the fuel properties were also studied when the ether
monoesters are used as diesel fuel additives.
Abstract: This paper presents an optimization method for
reducing the number of input channels and the complexity of the
feed-forward NARX neural network (NN) without compromising the
accuracy of the NN model. By utilizing the correlation analysis
method, the most significant regressors are selected to form the input
layer of the NN structure. An application of vehicle dynamic model
identification is also presented in this paper to demonstrate the
optimization technique and the optimal input layer structure and the
optimal number of neurons for the neural network is investigated.
Abstract: New design of three dimensional (3D) flywheel system
based on gimbal and gyro mechanics is proposed. The 3D flywheel
device utilizes the rotational motion of three spherical shells and the
conservation of angular momentum to achieve planar locomotion.
Actuators mounted to the ring-shape frames are installed within the
system to drive the spherical shells to rotate, for the purpose of steering
and stabilization. Similar to the design of 2D flywheel system, it is
expected that the spherical shells may function like a “flyball” to store
and supply mechanical energy; additionally, in comparison with
typical single-wheel and spherical robots, the 3D flywheel can be used
for developing omnidirectional robotic systems with better mobility.
The Lagrangian method is applied to derive the equation of motion of
the 3D flywheel system, and simulation studies are presented to verify
the proposed design.
Abstract: Pneumatic reactors have been widely employed in various sectors of the chemical industry, especially where are required high heat and mass transfer rates. This study aimed to obtain correlations that allow the prediction of gas hold-up (Ԑ) and volumetric oxygen transfer coefficient (kLa), and compare these values, for three models of pneumatic reactors on two scales utilizing Newtonian fluids. Values of kLa were obtained using the dynamic pressure-step method, while e was used for a new proposed measure. Comparing the three models of reactors studied, it was observed that the mass transfer was superior to draft-tube airlift, reaching e of 0.173 and kLa of 0.00904s-1. All correlations showed good fit to the experimental data (R2≥94%), and comparisons with correlations from the literature demonstrate the need for further similar studies due to shortage of data available, mainly for airlift reactors and high viscosity fluids.
Abstract: This paper presents the results of an experimental
study undertaken to evaluate the local bond stress-slip response of
short embedment of reinforcing bars in normal concrete (NC) and
high performance fiber reinforced cement composites (HPFRCC)
blocks. Long embedment was investigated as well to gain insights on
the distribution of strain, slip, bar stress and bond stress along the bar
especially in post-yield range. A total of 12 specimens were tested,
by means of pull-out of the reinforcing bars from concrete blocks. It
was found that the enhancement of local bond strength can be
reached up to 50% and ductility of the bond behavior was improved
significantly if HPFRCC is used. Also, under a constant strain at
loaded end, HPFRCC has delayed yielding of bars at other location
from the loaded end. Hence, the reduction of bond stress was slower
for HPFRCC in comparison with NC. Due to the same reason, the
total slips at loaded end for HPFRCC was smaller than NC as
expected. Test results indicated that HPFRCC has better bond slip
behavior which makes it a suitable material to be employed in
anchorage zone such as beam-column joints.
Abstract: The effect of partially substitution of magnetic
impurity Fe for Cu to the magnetic and transport properties in
electron-doped superconducting cuprates of
Eu1.85+yCe0.15-yCu1-yFeyO4+α-δ (ECCFO) with y = 0, 0.010, 0.020, and
0.050 has been studied, in order to investigate the mechanism of
magnetic and transport properties of ECCFO in normal-state.
Magnetic properties are investigated by DC magnetic-susceptibility
measurements that carried out at low temperatures down to 2 K using a
standard SQUID magnetometer in a magnetic field of 5 Oe on field
cooling. Transport properties addressed to electron mobility, are
extracted from radius of electron localization calculated from
temperature dependence of resistivity. For y = 0, temperature
dependence of dc magnetic-susceptibility (χ) indicated the change of
magnetic behavior from paramagnetic to diamagnetic below 15 K.
Above 15 K, all samples show paramagnetic behavior with the values
of magnetic moment in every volume unit increased with increasing y.
Electron mobility decreased with increasing y.
Abstract: Some plants of genus Schinus have been used in the
folk medicine as topical antiseptic, digestive, purgative, diuretic,
analgesic or antidepressant, and also for respiratory and urinary
infections. Chemical composition of essential oils of S. molle and S.
terebinthifolius had been evaluated and presented high variability
according with the part of the plant studied and with the geographic
and climatic regions. The pharmacological properties, namely
antimicrobial, anti-tumoural and anti-inflammatory activities are
conditioned by chemical composition of essential oils. Taking into
account the difficulty to infer the pharmacological properties of
Schinus essential oils without hard experimental approach, this work
will focus on the development of a decision support system, in terms
of its knowledge representation and reasoning procedures, under a
formal framework based on Logic Programming, complemented with
an approach to computing centered on Artificial Neural Networks
and the respective Degree-of-Confidence that one has on such an
occurrence.
Abstract: Optical biosensors have become a powerful detection
and analysis tool for wide-ranging applications in biomedical research,
pharmaceuticals and environmental monitoring. This study carried out
the computational fluid dynamics (CFD)-based simulations to explore
the dispersion phenomenon in the micro channel of an optical
biosensor. The predicted time sequences of concentration contours
were utilized to better understand the dispersion development occurred
in different geometric shapes of micro channels. The simulation results
showed the surface concentrations at the sensing probe (with the best
performance of a grating coupler) in respect of time to appraise the
dispersion effect and therefore identify the design configurations
resulting in minimum dispersion.
Abstract: In a practical power system, the power plants are not
located at the same distance from the center of loads and their fuel
costs are different. Also, under normal operating conditions, the
generation capacity is more than the total load demand and losses.
Thus, there are many options for scheduling generation. In an
interconnected power system, the objective is to find the real and
reactive power scheduling of each power plant in such a way as to
minimize the operating cost. This means that the generator’s real and
reactive powers are allowed to vary within certain limits so as to meet
a particular load demand with minimum fuel cost. This is called
optimal power flow problem. In this paper, Economic Load Dispatch
(ELD) of real power generation is considered. Economic Load
Dispatch (ELD) is the scheduling of generators to minimize total
operating cost of generator units subjected to equality constraint of
power balance within the minimum and maximum operating limits of
the generating units. In this paper, genetic algorithms are considered.
ELD solutions are found by solving the conventional load flow
equations while at the same time minimizing the fuel costs.
Abstract: Any variation in environmental characteristics of
geomorphosites would lead to destabilisation of their geotouristic
values all around the planet. The Urmia lake, with an area of
approximately 5,500 km2 and a catchment area of 51,876 km2, and to
which various reasons over time, especially in the last fifty years
have seen a sharp decline and have decreased by about 93 % in two
recent decades. These variations are not only driving significant
changes in the morphology and ecology of the present lake
landscape, but at the same time are shaping newly formed
morphologies, which vanished some valuable geomorphosites or
develop into smaller geomorphosites with significant value from a
scientific and cultural point of view. This paper analyses and
discusses features and evolution in several representative coastal and
island geomorphosites. For this purpose, a total of 23 geomorphosites
were studied in two data series (1963 and 2015) and the respective
data were compared and analysed. The results showed, the total loss
in geomorphosites area in a half century amounted to a loss of more
than 90% of the valuable geomorphosites. Moreover, the comparison
between the mean yearly value of coastal area lost over the entire
period and the yearly average calculated for the shorter period (1998-
2014) clearly indicates a pattern of acceleration. This acceleration in
the rate of reduction in lake area was seen in most of the southern
half of the lake. In the region as well, the general water-level falling
is not only causing the loss of a significant water resource, which is
followed by major impact on regional ecosystems, but is also driving
the most marked recent (last century) changes in the geotouristic
landscapes. In fact, the disappearance of geomorphosites means the
loss of tourism phenomenon. In this context attention must be paid to
the question of conservation. The action needed to safeguard
geomorphosites includes: 1) Preventive action, 2) Corrective action,
and 3) Sharing knowledge.
Abstract: In this study, one of the tools of Islamic financing
known as “Sukuk” a non-interest bearing investment which has
started to be implemented in Turkey and the world as a whole is
discussed. In order to increase the vitality and efficiency of the
economy, by taking lessons from the recent economic crisis new
developments in the banking and investment sector are being
expanded. The purpose of all investors is to obtain more revenue
through the use of capital. The inability of traditional investment
tools to meet the expectations of investors and the interest based
financial system where one investor benefits at the expense of
another there has been the need for a different, reliable and noninterest
bearing financial market that is consistent with the Islamic
rule. As a result an alternative and more reliable interest free
financing tool “Sukuk” rental certificates covering people who are
sensitive to Islamic rules, appeal to all segments, hidden remaining
capital that contributes to the economy, reduce disparities in income
distribution, common risk sharing system of profit and loss sharing
has emerged. Today, for the structural countries by examining the
state of the world market economy the applicability, enactment and
future issues associated with this attractive kind of Islamic finance
namely the “Sukuk” market has been explained.