Abstract: In order to solve problems associated with stormwater runoff in urban areas and their effects on natural and artificial water bodies, the integration of new technical solutions to the rainwater drainage becomes even more essential. Permeable pavement systems are one of the most widely used techniques. This paper presents a laboratory analysis of stormwater runoff hydraulic and pollutant removal performance of permeable pavement system using pervious pavements based on seashell products. The laboratory prototype is a square column of 25 cm of side and consists of the surface in pervious concrete, a bedding of 3 cm in height, a geotextile and a subbase layer of 50 cm in height. A series of constant simulated rain events using semi-synthetic runoff which varied in intensity and duration were carried out. The initial vertical saturated hydraulic conductivity of the entire pervious pavement system was 0.25 cm/s (148 L/m2/min). The hydraulic functioning was influenced by both the inlet flow rate value and the test duration. The total water losses including evaporation ranged between 9% to 20% for all hydraulic experiments. The temporal and vertical variability of the pollutant removal efficiency (PRE) of the system were studied for total suspended solids (TSS). The results showed that the PRE along the vertical profile was influenced by the size of the suspended solids, and the pervious paver has the highest capacity to trap pollutant than the other porous layers of the permeable pavement system after the geotextile. The TSS removal efficiency was about 80% for the entire system. The first-flush effect of TSS was observed, but it appeared only at the beginning (2 to 6 min) of the experiments. It has been shown that the PPS can capture first-flush. The project in which this study is integrated aims to contribute to both the valorization of shellfish waste and the sustainable management of rainwater.
Abstract: Whey is an excellent food ingredient owing to its high nutritive value and its functional properties. However, composition of whey varies depending on composition of milk, processing conditions, processing method, and its whey protein content. The aim of this study was to prepare a whey powder from raw whey and to determine the influence of different processing temperatures (160 and 180 °C) on the physicochemical, functional properties during storage of 180 days and on whey protein denaturation. Results have shown that temperature significantly (P < 0.05) affects the pH, acidity, non-protein nitrogen (NPN), protein total soluble solids, fat and lactose contents. Significantly (p < 0.05) higher foaming capacity (FC), foam stability (FS), whey protein nitrogen index (WPNI), and a lower turbidity and solubility index (SI) were observed in whey powder processed at 160 °C compared to whey powder processed at 180 °C. During storage of 180 days, slow but progressive changes were noticed on the physicochemical and functional properties of whey powder. Reverse phase-HPLC analysis revealed a significant (P < 0.05) effect of temperature on whey protein contents. Denaturation of β-Lactoglobulin is followed by α-lacalbumin, casein glycomacropeptide (CMP/GMP), and bovine serum albumin (BSA).
Abstract: Tricalcium phosphate (β-Ca3(PO4)2, β-TCP) powders were synthesized using wet polymeric precipitation method for the first time to our best knowledge. The results of X-ray diffraction analysis showed the formation of almost single a Ca-deficient hydroxyapatite (CDHA) phase of a poor crystallinity already at room temperature. With continuously increasing the calcination temperature up to 800 °C, the crystalline β-TCP was obtained as the main phase. It was demonstrated that infrared spectroscopy is very effective method to characterize the formation of β-TCP. The SEM results showed that β-TCP solids were homogeneous having a small particle size distribution. The β-TCP powders consisted of spherical particles varying in size from 100 to 300 nm. Fabricated β-TCP specimens were placed to the bones of the rats and maintained for 1-2 months.
Abstract: In this numerical work, natural convection and entropy generation of Al2O3–water nanofluid in square cavity have been studied. A two-dimensional steady laminar natural convection in a differentially heated square cavity of length L, filled with a nanofluid is investigated numerically. The horizontal walls are considered adiabatic. Vertical walls corresponding to x=0 and x=L are respectively maintained at hot temperature, Th and cold temperature, Tc. The resolution is performed by the CFD code "FLUENT" in combination with GAMBIT as mesh generator. These simulations are performed by maintaining the Rayleigh numbers varied as 103 ≤ Ra ≤ 106, while the solid volume fraction varied from 1% to 5%, the particle size is fixed at dp=33 nm and a range of the temperature from 20 to 70 °C. We used models of thermophysical nanofluids properties based on experimental measurements for studying the effect of adding solid particle into water in natural convection heat transfer and entropy generation of nanofluid. Such as models of thermal conductivity and dynamic viscosity which are dependent on solid volume fraction, particle size and temperature. The average Nusselt number is calculated at the hot wall of the cavity in a different solid volume fraction. The most important results is that at low temperatures (less than 40 °C), the addition of nanosolids Al2O3 into water leads to a decrease in heat transfer and entropy generation instead of the expected increase, whereas at high temperature, heat transfer and entropy generation increase with the addition of nanosolids. This behavior is due to the contradictory effects of viscosity and thermal conductivity of the nanofluid. These effects are discussed in this work.
Abstract: Drinking water is supplied to Danbatta, Makoda and some parts of Minjibir local government areas of Kano State from the surface water of Thomas Reservoir. The present land use in the catchment area of the reservoir indicates high agricultural activities, fishing, as well as domestic and small scale industrial activities. To study and monitor the quality of surface and drinking water of the area, water samples were collected from the reservoir, treated water at the treatment plant and potable water at the consumer end in three seasons November - February (cold season), March - June (dry season) and July - September (rainy season). The samples were analyzed for physical and chemical parameters, pH, temperature, total dissolved solids (TDS), conductivity, turbidity, total hardness, suspended solids, total solids, colour, dissolved oxygen (DO), biological oxygen demand (BOD), chloride ion (Cl-) nitrite (NO2-), nitrate (NO3-), chemical oxygen demand (COD) and phosphate (PO43-). The higher values obtained in some parameters with respect to the acceptable standard set by World Health Organization (WHO) and Nigerian Industrial Standards (NIS) indicate the pollution of both the surface and drinking water. These pollutants were observed to have a negative impact on water quality in terms of eutrophication, largely due to anthropogenic activities in the watershed.
Abstract: The control of ammonia build-up and its by-product is a limiting factor for a successful commercial aquaculture in a developing country like Nigeria. The technology for an advanced treatment of fish tank effluent is uneconomical to local fish farmers which have led to indiscriminate disposal of aquaculture wastewater, thereby increasing the concentrations of these nitrogenous compound and other contaminants in surface and groundwater above the permissible level. Phytoremediation using water lettuce could offer cheaper and sustainable alternative. On the first day of experimentation, approximately 100 g of water lettuce were replicated in four hydroponic units containing aquaculture effluents. The water quality parameters measured were concentration of ammonium–nitrogen (NH4+-N), nitrite-nitrogen (NO2--N), nitrate-nitrogen (NO3--N), and phosphate–phosphorus (PO43--P). Others were total suspended solids (TSS), pH, electrical conductivity (EC), and biomass value. At phytoremediation intervals of 7, 14, 21 and 28 days, the biomass recorded were 361.2 g, 498.7 g, 561.2 g, and 623.7 g. Water lettuce was able to reduce the pollutant concentration of all the selected parameter. The percentage reduction of pH ranged from 3.9% to 14.4%, EC from 49.8% to 96.2%, TDS from 50.4% to 96.2%, TSS from 38.3% to 81.7%, NH4+-N from 38.9% to 90.7%, NO2--N from 0% to 74.9%, NO3--N from 63.2% to 95.9% and PO43--P from 0% to 76.3%. At 95% confidence level, the analysis of variance shows that F(critical) is less than F(cal) and p < 0.05; therefore, it can be concluded statistically that the inequality between the pre-treatment and post-treatment values are significant. This suggests the potency of water lettuce for remediation of aquaculture effluent.
Abstract: A vibrating-fork sensor can measure the level height of solids and liquids and operates according to the principle that vibrations created by piezoelectric ceramics are transmitted to the vibrating fork, which produces resonance. When the vibrating fork touches an object, its resonance frequency changes and produces a signal that returns to a controller for immediate adjustment, so as to effectively monitor raw material loading. The design of the vibrating fork in a vibrating-fork material sensor is crucial. In this paper, ANSYS finite element analysis software is used to perform modal analysis on the vibrations of the vibrating fork. In addition, to design and produce a superior vibrating fork, the dimensions and welding shape of the vibrating fork are compared in a simulation performed using the Taguchi method.
Abstract: In aerovehicles context, the flow around an Ahmed
body profile is simulated using the velocity-vorticity formulation of
the Navier-Stokes equations, associated to a penalization method for
solids and Large Eddy Simulation for turbulence. The study focuses
both on the ground influence on the flow and on the dissymetry of
the wake, observed for a ground clearance greater than 10% of the
body height H. Unsteady and mean flows are presented and analyzed.
POD study completes the analysis and gives information on the most
energetic structures of the flow.
Abstract: The experimental trial was carried out in open field at Foggia district (Apulia Region, Southern Italy), during the spring-summer season 2014, in order to evaluate the effect of four biostimulant products (RadiconÒ, Viormon plusÒ, LysodinÒ and SiaptonÒ 10L), compared with a control (no biostimulant), on the infestation of processing tomato crop (cv Dres) by the chlorophyll-lacking root parasite Phelipanche ramosa. Biostimulants consist in different categories of products (microbial inoculants, humic and fulvic acids, hydrolyzed proteins and aminoacids, seaweed extracts) which play various roles in plant growing, including the improvement of crop resistance and quali-quantitative characteristics of yield. The experimental trial was arranged according to a complete randomized block design with five treatments, each of one replicated three times. The processing tomato seedlings were transplanted on 5 May 2014. Throughout the crop cycle, P. ramosa infestation was assessed according to the number of emerged shoots (branched plants) counted in each plot, at 66, 78 and 92 day after transplanting. The tomato fruits were harvested at full-stage of maturity on 8 August 2014. From each plot, the marketable yield was measured and the quali-quantitative yield parameters (mean weight, dry matter content, colour coordinate, colour index and soluble solids content of the fruits) were determined. The whole dataset was tested according to the basic assumptions for the analysis of variance (ANOVA) and the differences between the means were determined using Tukey’s tests at the 5% probability level. The results of the study showed that none of the applied biostimulants provided a whole control of Phelipanche, although some positive effects were obtained from their application. To this respect, the RadiconÒ appeared to be the most effective in reducing the infestation of this root-parasite in tomato crop. This treatment also gave the higher tomato yield.
Abstract: Membrane technology is convenient for separation of suspended solids, colloids and high molecular weight materials that are present. The idea is that the waste stream from edible oil industry, after the separation of oil by using skimmers is subjected to microfiltration and the obtained permeate can be used again in the production process. The wastewater from edible oil industry was used for the microfiltration. For the microfiltration of this effluent a tubular membrane was used with a pore size of 200 nm at transmembrane pressure in range up to 3 bar and in range of flow rate up to 300 L/h. Box–Behnken design was selected for the experimental work and the responses considered were permeate flux and chemical oxygen demand (COD) reduction. The reduction of the permeate COD was in the range 40-60% according to the feed. The highest permeate flux achieved during the process of microfiltration was 160 L/m2h.
Abstract: Conventional wastewater treatment plants of activated carbon, electrodialysis, ion exchange, reverse osmosis etc. are expensive to install, operate and maintain especially in developing countries; therefore, the use of aquatic macrophytes for wastewater purification is a viable alternative. On the first day of experimentation, approximately 100g of water hyacinth was introduced into the hydroponic units in four replicates. The water quality parameters measured were total suspended solids (TSS), pH and electrical conductivity (EC). Others were concentration of ammonium–nitrogen (NH4+-N), nitrite-nitrogen (NO2--N), nitrate-nitrogen (NO3--N), phosphate–phosphorus (PO43--P), and biomass value. At phytoremediation intervals of 7, 14, 21 and 28 days, the biomass recorded were 438.2 g, 600.7 g, 688.2 g and 725.7 g. Water hyacinth was able to reduce the pollutant concentration of all the selected parameter. The percentage reduction of pH ranged from 1.9% to 14.7%, EC from 49.8% to 97.0%, TDS from 50.4% to 97.6%, TSS from 34.0% to 78.3%, NH4+-N from 38.9% to 85.2%, NO2--N from 0% to 84.6%, NO3--N from 63.2% to 98.8% and PO43--P from 10% to 88.0%. Paired sample t-test shows that at 95% confidence level, it can be concluded statistically that the inequality between the pre-treatment and post-treatment values are significant. This suggests that the use of water hyacinth is valuable in the design and operation of aquaculture effluent treatment and should therefore be adopted by environmental and wastewater managers.
Abstract: In this study, the anaerobic treatability of chicken manure diluted with tap water (with an influent feed ratio of 1 kg of fresh chicken manure to 6 liter of tap water) was investigated in a lab-scale anaerobic sludge bed (ASB) reactor inoculated with the granular sludge already adapted to chicken manure. The raw waste digested in this study was the manure from laying-hens having average total solids (TS) of about 30% with ca. 60% volatile content. The ASB reactor was fed semi-continuously at ambient operating temperature range (17-23◦C) at a HRT of 13 and 26 days for about 6 months, respectively. The respective average total and soluble chemical oxygen demand (COD) removals were ca. 90% and 75%, whereas average biomethane production rate was calculated ca. 180 lt per kg of CODremoved from the ASB reactor at an average HRT of 13 days. Moreover, total suspended solids (TSS) and volatile suspended solids (VSS) in the influent were reduced more than 97%. Hence, high removals of the organic compounds with respective biogas production made anaerobic stabilization of the diluted chicken manure by ASB reactor at ambient operating temperatures viable. By this way, external heating up to 35◦C (i.e. anaerobic processes have been traditionally operated at mesophilic conditions) could be avoided in the scope of this study.
Abstract: Biological processes based on oxidation of sulfur
compounds by chemolithotrophic microorganisms are emerging as an
efficient and eco-friendly technique for removal of sulfur from the
coal. In the present article, study was carried out to investigate the
potential of biodesulfurization process in removing the sulfur from
lignite coal sample collected from a Mongolian coal mine. The batch
biodesulfurization experiments were conducted in 2.5 L borosilicate
baffle type reactors at 35 ºC using Acidithiobacillus ferrooxidans.
The effect of pulp density on efficiency of biodesulfurization was
investigated at different solids concentration (1-10%) of coal. The
results of the present study suggested that the rate of desulfurization
was retarded at higher coal pulp density. The optimum pulp density
found 5% at which about 48% of the total sulfur was removed from
the coal.
Abstract: Topology optimization technique utilizes constant
element densities as design parameters. Finally, optimal distribution
contours of the material densities between voids (0) and solids (1) in
design domain represent the determination of topology. It means that
regions with element density values become occupied by solids in
design domain, while there are only void phases in regions where no
density values exist. Therefore the void regions of topology
optimization results provide design information to decide appropriate
depositions of web-opening in structure. Contrary to the basic
objective of the topology optimization technique which is to obtain
optimal topology of structures, this present study proposes a new idea
that topology optimization results can be also utilized for decision of
proper web-opening’s position. Numerical examples of linear
elastostatic structures demonstrate efficiency of methodological
design processes using topology optimization in order to determinate
the proper deposition of web-openings.
Abstract: Anthropogenic sources of zinc (Zn), including industrial emissions and effluents, Zn–rich fertilizer materials and pesticides containing Zn, can contribute to increasing the concentration of soluble Zn at levels toxic to plants in acid sandy soils. The application of municipal sewage sludge or biosolids (MBS) which contain metal immobilizing agents on coarse-textured soils could improve the metal sorption capacity of the low-CEC soils. The purpose of this experiment was to evaluate the sorption of Zn in surface samples (0-15 cm) of six Quebec (Canada) soils amended with MBS (pH 6.9) from Val d’Or (Quebec, Canada). Soil samples amended with increasing amounts (0 to 20%) of MBS were equilibrated with various amounts of Zn as ZnCl2 in 0.01 M CaCl2 for 48 hours at room temperature. Sorbed Zn was calculated from the difference between the initial and final Zn concentration in solution. Zn sorption data conformed to the linear form of Freundlich equation. The amount of sorbed Zn increased considerably with increasing MBS rate. Analysis of variance revealed a highly significant effect (p ≤ 0.001) of soil texture and MBS rate on the amount of sorbed Zn. The average values of the Zn-sorption capacity of MBS-amended coarse-textured soils were lower than those of MBS-amended fine textured soils. The two sandy soils (86-99% sand) amended with MBS retained 2- to 5-fold Zn than those without MBS (control). Significant Pearson correlation coefficients between the Zn sorption isotherm parameter, i.e. the Freundlich sorption isotherm (KF), and commonly measured physical and chemical entities were obtained. Among all the soil properties measured, soil pH gave the best significant correlation coefficients (p ≤ 0.001) for soils receiving 0, 5 and 10% MBS. Furthermore, KF values were positively correlated with soil clay content, exchangeable basic cations (Ca, Mg or K), CEC and clay content to CEC ratio. From these results, it can be concluded that (i) municipal biosolids provide sorption sites that have a strong affinity for Zn, (ii) both soil texture, especially clay content, and soil pH are the main factors controlling anthropogenic Zn sorption in the municipal biosolids-amended soils, and (iii) the effect of municipal biosolids on Zn sorption will be more pronounced for a sandy soil than for a clay soil.
Abstract: Water is a very rare natural resource in South Africa. Ga-Selati River is used for both domestic and industrial purposes. This study was carried out in order to assess the quality of Ga-Selati River in a mining area of Limpopo Province-Phalaborwa. The pH, Electrical Conductivity (EC) and Total Dissolved Solids (TDS) were determined using a Crinson multimeter while turbidity was measured using a Labcon Turbidimeter. The concentrations of Al, Ca, Cd, Cr, Fe, K, Mg, Mn, Na and Pb were analysed in triplicate using a Varian 520 flame atomic absorption spectrometer (AAS) supplied by PerkinElmer, after acid digestion with nitric acid in a fume cupboard. The average pH of the river from eight different sampling sites was 8.00 and 9.38 in wet and dry season respectively. Higher EC values were determined in the dry season (138.7 mS/m) than in the wet season (96.93 mS/m). Similarly, TDS values were higher in dry (929.29 mg/L) than in the wet season (640.72 mg/L) season. These values exceeded the recommended guideline of South Africa Department of Water Affairs and Forestry (DWAF) for domestic water use (70 mS/m) and that of the World Health Organization (WHO) (600 mS/m), respectively. Turbidity varied between 1.78-5.20 and 0.95-2.37 NTU in both wet and dry seasons. Total hardness of 312.50 mg/L and 297.75 mg/L as the concentration of CaCO3 was computed for the river in both the wet and the dry seasons and the river water was categorised as very hard. Mean concentration of the metals studied in both the wet and the dry seasons are: Na (94.06 mg/L and 196.3 mg/L), K (11.79 mg/L and 13.62 mg/L), Ca (45.60 mg/L and 41.30 mg/L), Mg (48.41 mg/L and 44.71 mg/L), Al (0.31 mg/L and 0.38 mg/L), Cd (0.01 mg/L and 0.01 mg/L), Cr (0.02 mg/L and 0.09 mg/L), Pb (0.05 mg/L and 0.06 mg/L), Mn (0.31 mg/L and 0.11 mg/L) and Fe (0.76 mg/L and 0.69 mg/L). Results from this study reveal that most of the metals were present in concentrations higher than the recommended guidelines of DWAF and WHO for domestic use and the protection of aquatic life.
Abstract: Mineral product, waste concrete (fine aggregates),
waste in the optical field, industry, and construction employ separators
to separate solids and classify them according to their size. Various
sorting machines are used in the industrial field such as those operating
under electrical properties, centrifugal force, wind power, vibration,
and magnetic force. Study on separators has been carried out to
contribute to the environmental industry. In this study, we perform
CFD analysis for understanding the basic mechanism of the separation
of waste concrete (fine aggregate) particles from air with a machine
built with a rotor with blades. In CFD, we first performed
two-dimensional particle tracking for various particle sizes for the
model with 1 degree, 1.5 degree, and 2 degree angle between each
blade to verify the boundary conditions and the method of rotating
domain method to be used in 3D. Then we developed 3D numerical
model with ANSYS CFX to calculate the air flow and track the
particles. We judged the capability of particle separation for given size
by counting the number of particles escaping from the domain toward
the exit among 10 particles issued at the inlet. We confirm that
particles experience stagnant behavior near the exit of the rotating
blades where the centrifugal force acting on the particles is in balance
with the air drag force. It was also found that the minimum particle
size that can be separated by the machine with the rotor is determined
by its capability to stay at the outlet of the rotor channels.
Abstract: River Hindon is an important river catering the
demand of highly populated rural and industrial cluster of western
Uttar Pradesh, India. Water quality of river Hindon is deteriorating at
an alarming rate due to various industrial, municipal and agricultural
activities. The present study aimed at identifying the pollution
sources and quantifying the degree to which these sources are
responsible for the deteriorating water quality of the river. Various
water quality parameters, like pH, temperature, electrical
conductivity, total dissolved solids, total hardness, calcium, chloride,
nitrate, sulphate, biological oxygen demand, chemical oxygen
demand, and total alkalinity were assessed. Water quality data
obtained from eight study sites for one year has been subjected to the
two multivariate techniques, namely, principal component analysis
and cluster analysis. Principal component analysis was applied with
the aim to find out spatial variability and to identify the sources
responsible for the water quality of the river. Three Varifactors were
obtained after varimax rotation of initial principal components using
principal component analysis. Cluster analysis was carried out to
classify sampling stations of certain similarity, which grouped eight
different sites into two clusters. The study reveals that the
anthropogenic influence (municipal, industrial, waste water and
agricultural runoff) was the major source of river water pollution.
Thus, this study illustrates the utility of multivariate statistical
techniques for analysis and elucidation of multifaceted data sets,
recognition of pollution sources/factors and understanding
temporal/spatial variations in water quality for effective river water
quality management.
Abstract: This study aims at improving the urban hydrological
cycle of the Orléans agglomeration (France) and understanding the
relationship between physical and chemical parameters of urban
surface runoff and the hydrological conditions. In particular water
quality parameters such as pH, conductivity, total dissolved solids,
major dissolved cations and anions, and chemical and biological
oxygen demands were monitored for three types of urban water
discharges (wastewater treatment plant output (WWTP), storm
overflow and stormwater outfall) under two hydrologic scenarios (dry
and wet weather). The first results were obtained over a period of five
months. Each investigated (Ormes, l’Egoutier and La Corne) outfall
represents an urban runoff source that receives water from runoff
roads, gutters, the irrigation of gardens and other sources of flow over
the Earth’s surface that drains in its catchments and carries it to the
Loire River. In wet weather conditions there is rain water runoff and
an additional input from the roof gutters that have entered the
stormwater system during rainfall. For the comparison the results La
Chilesse is a storm overflow that was selected in our study as a
potential source of waste water which is located before the (WWTP). The comparison of the physical-chemical parameters (total
dissolved solids, turbidity, pH, conductivity, dissolved organic
carbon (DOC), concentration of major cations and anions) together
with the chemical oxygen demand (COD) and biological oxygen
demand (BOD) helped to characterize sources of runoff waters in the
different watersheds. It also helped to highlight the infiltration of
wastewater in some stormwater systems that reject directly in the
Loire River. The values of the conductivity measured in the outflow
of Ormes were always higher than those measured in the other two
outlets. The results showed a temporal variation for the Ormes outfall
of conductivity from 1465 μS cm-1 in the dry weather flow to 650 μS
cm-1 in the wet weather flow and also a spatial variation in the wet
weather flow from 650 μS cm-1 in the Ormes outfall to 281 μS cm-1
in L’Egouttier outfall. The ultimate BOD (BOD28) showed a
significant decrease in La Corne outfall from 181 mg L-1 in the wet
weather flow to 95 mg L-1 in the dry weather flow because of the
nutrient load that was transported by the runoff.
Abstract: Lyophilization, also called freeze-drying, is an
important dehydration technique mainly used for pharmaceuticals.
Food industry also uses lyophilization when it is important to retain
most of the nutritional quality, taste, shape and size of dried products
and to extend their shelf life. Vacuum-Induced during freezing cycle
(VI) has been used in order to control ice nucleation and,
consequently, to reduce the time of primary drying cycle of
pharmaceuticals preserving quality properties of the final product.
This procedure has not been applied in freeze drying of foods. The
present work aims to investigate the effect of VI on the lyophilization
drying time, final moisture content, density and reconstitutional
properties of mango (Mangifera indica L.) slices (MS) and mango
pulp-maltodextrin dispersions (MPM) (30% concentration of total
solids). Control samples were run at each freezing rate without using
induced vacuum. The lyophilization endpoint was the same for all
treatments (constant difference between capacitance and Pirani
vacuum gauges). From the experimental results it can be concluded
that at the high freezing rate (0.4°C/min) reduced the overall process
time up to 30% comparing process time required for the control and
VI of the lower freeze rate (0.1°C/min) without affecting the quality
characteristics of the dried product, which yields a reduction in costs
and energy consumption for MS and MPM freeze drying. Controls
and samples treated with VI at freezing rate of 0.4°C/min in MS
showed similar results in moisture and density parameters.
Furthermore, results from MPM dispersion showed favorable values
when VI was applied because dried product with low moisture
content and low density was obtained at shorter process time
compared with the control. There were not found significant
differences between reconstitutional properties (rehydration for MS
and solubility for MPM) of freeze dried mango resulting from
controls, and VI treatments.