Abstract: The Beshar River is one aquatic ecosystem, which is
located next to the city of Yasuj in southern Iran. The Beshar river
has been contaminated by industrial factories such as effluent of
sugar factory, agricultural and other activities in this region such as,
Imam Sajjad hospital, drainage from agricultural farms, Yasuj urban
surface runoff and effluent of wastewater treatment plants ,specially
Yasuj waste water treatment plant. In order to evaluate the effects of
these pollutants on the quality of the Beshar river, five monitoring
stations were selected along its course. The first station is located
upstream of Yasuj near the Dehnow village; stations 2 to 4 are
located east, south and west of city; and the 5th station is located
downstream of Yasuj. Several water quality parameters were
sampled. These include pH, dissolved oxygen, biological oxygen
demand (BOD), temperature, conductivity, turbidity, total dissolved
solids and discharge or flow measurements. Water samples from the
five stations were collected and analyzed to determine the following
physicochemical parameters: EC, pH, T.D.S, T.H, No2, DO, BOD5,
COD during 2008 to 2010. The study shows that the BOD5 value of
station 1 is at a minimum (1.7 ppm) and increases downstream from
stations 2 to 4 to a maximum (11.6 ppm), and then decreases at
station 5. The DO values of station 1 is a maximum (8.45 ppm),
decreases downstream to stations 2 - 4 which are at a minimum (3.1
ppm), before increasing at station 5. The amount of BOD and TDS
are highest at the 4th station and the amount of DO is lowest at this
station, marking the 4th station as more highly polluted than the
other stations .This study shows average amount of the water quality
parameters in first year of sampling (2008) have had a better quality
relation to third year in 2010 because of recent drought in this region
and pollutant increasing .As the Beshar river path after 5th station
goes through the mountain area with more slope and flow velocity
,so the physicochemical parameters improve at the 5th station due to
pollutant degradation and dilution. Finally the point and nonpoint
pollutant sources of Beshar river were determined and compared to
the monitoring results.
Abstract: Some physico-chemical characteristics and mineral
composition of 'Karayemis' (Prunus laurocerasus L.) fruits which
grown naturally in Norteast Turkey was studied. 28 minerals ( Al,
Mg, B, Mn, Co, Na, Ca, Ni, Cd, P, Cr, Pb, Cu, S, Fe, Zn, K, Sr, Li,
As, V, Ag, Ba, Br, Ga, In, Se, Ti) were analyzed and 19 minerals
were present at ascertainable levels. Karayemis fruit was richest in
potassium (7938.711 ppm), magnesium (1242.186 ppm) and calcium
(1158.853 ppm). And some physico-chemical characteristics of
Karayemis fruit was investigated. Fruit length, fruit width, fruit
thickness, fruit weight, total soluble solids, colour, protein, crude ash,
crude fiber, crude oil values were determined as 2.334 cm, 1.884 cm,
2.112 cm, 5.35 g, 20.1 %, S99M99Y99, 0.29 %, 0.22 %, 6.63 % and
0.001 %, respectively. The seed of fruit mean weight, length, width
and thickness were found to be 0.41 g, 1.303 cm, 0.921 cm and
0.803, respectively.
Abstract: Prickly pear juice has received renewed attention with regard to the effects of processing and preservation on its sensory qualities (colour, taste, flavour, aroma, astringency, visual browning and overall acceptability). Juice was prepared by homogenizing fruit and treating the pulp with pectinase (Aspergillus niger). Juice treatments applied were sugar addition, acidification, heat-treatment, refrigeration, and freezing and thawing. Prickly pear pulp and juice had unique properties (low pH 3.88, soluble solids 3.68 oBrix and high titratable acidity 0.47). Sensory profiling and descriptive analyses revealed that non-treated juice had a bitter taste with high astringency whereas treated prickly pear was significantly sweeter. All treated juices had a good sensory acceptance with values approximating or exceeding 7. Regression analysis of the consumer sensory attributes for non-treated prickly pear juice indicated an overwhelming rejection, while treated prickly pear juice received overall acceptability. Thus, educed favourable sensory responses and may have positive implications for consumer acceptability.
Abstract: The theoretical prediction of the acoustical
polarization effects in the heterogeneous composites, made of thick
elastic solids with thin nematic films, is presented. The numericalanalytical
solution to the problem of the different wave propagation
exhibits some new physical effects in the low frequency domain: the
appearance of the critical frequency and the existence of the narrow
transition zone where the wave rapidly changes its speed. The
associated wave attenuation is highly perturbed in this zone. We also
show the possible appearance of the critical frequencies where the
attenuation changes the sign. The numerical results of parametrical
analysis are presented and discussed.
Abstract: fifteen cultivars of Strawberries (Queen Eliza, Sequia,
Paros, Mcdonance, Selva, Chandler, Mrak, Ten beauty, Aliso, Pajero,
Kordestan, Camarosa, Blackmore, Gaviota and Fresno) were
investigated in 2011, under hydroponic system condition. Yield and
fruit Firmness was determinate. Chemical analyses of soluble solids
content (SSC), titratable acidity (TA), ascorbic acid (AA) and pH
were done. 4 cultivars (Aliso, Selva, Paros and Gaviota) yielded more
than 250 g/plant, while cultivar Black more, Fresno and Kordestan
produced less than 100g/plant. The amounts of fruit firmness
indicated that 'Camarosa' fruit was firmer than others cultivars.
Cultivar 'Fresno' had the highest pH (3.27). Ttitratable acidity varied
from 1.03g/l00g for cultivar 'Sequia' and 'Gaviota' to 1.48g/l00g for
cultivar 'Chandler'. Fresno, Kordestan, Aliso and Chandler showed
the highest soluble solid concentration. Ascorbic acid averaged for
most cultivars between 30.26 and 79.73 mg/100gf.w. Present results
showed that different cultivars of strawberry contain highly variable
in fruit quality.
Abstract: Zinc borates can be used as multi-functional
synergistic additives with flame retardant additives in polymers. Zinc
borate is white, non-hygroscopic and powder type product. The most
important properties are low solubility in water and high dehydration
temperature. Zinc borates dehydrate above 290°C and anhydrous zinc
borate has thermal resistance about 400°C. Zinc borates can be
synthesized using several methods such as hydrothermal and solidstate
processes. In this study, the solid-state method was applied at
low temperatures of 600oC and 700oC using the starting materials of
ZnO and H3BO3 with several mole ratios. The reaction time was
determined as 4 hours after some preliminary experiments. After the
synthesis, the crystal structure and the morphology of the products
were examined by X-Ray Diffraction (XRD) and Fourier Transform
Infrared Spectroscopy (FT-IR). As a result the forms of ZnB4O7,
Zn3(BO3)2, ZnB2O4 were synthesized and obtained along with the
unreacted ZnO.
Abstract: This paper presents the results of the preliminary investigation of microwave (MW) irradiation pretreatments on the anaerobic digestion of food residues using biochemical methane potential (BMP) assays. Low solids systems with a total solids (TS) content ranging from 5.0-10.0% were analyzed. The inoculum to bulk mass of substrates to water ratio was 1:2:2 (mass basis). The experimental conditions for pretreatments were as follows: a control (no MW irradiation), two runs with MW irradiation for 15 and 30 minutes at 320 W, and another two runs with MW irradiation at 528 W for 30 and 60 minutes. The cumulative biogas production were 6.3 L and 8.7 L for 15min/320 W and 30min/320 W MW irradiation conditions, respectively, and 10.5 L and 11.4 L biogas for 30min/528 W and 60min/528 W, respectively, as compared to the control giving 5.8 L biogas. Both an increase in exposure time of irradiation and power of MW had increased the rate and yield of biogas. Singlefactor ANOVA tests (p
Abstract: A new concept for long-term reagent storage for Labon- a-Chip (LoC) devices is described. Here we present a polymer multilayer stack with integrated stick packs for long-term storage of several liquid reagents, which are necessary for many diagnostic applications. Stick packs are widely used in packaging industry for storing solids and liquids for long time. The storage concept fulfills two main requirements: First, a long-term storage of reagents in stick packs without significant losses and interaction with surroundings, second, on demand releasing of liquids, which is realized by pushing a membrane against the stick pack through pneumatic pressure. This concept enables long-term on-chip storage of liquid reagents at room temperature and allows an easy implementation in different LoC devices.
Abstract: Sorghum flour was supplemented with 15 and 30%
chickpea flour. Sorghum flour and the supplement were fermented at
35 oC for 0, 8, 16, and 24 h. Changes in pH, titrable acidity, total
soluble solids, protein content, in vitro protein digestibility and
amino acid composition were investigated during fermentation and/or
after supplementation of sorghum flour with chickpea. The pH of the
fermenting material decreased sharply with a concomitant increase in
the titrable acidity. The total soluble solids remained unchanged with
progressive fermentation time. The protein content of sorghum
cultivar was found to be 9.27 and that of chickpea was 22.47%. The
protein content of sorghum cultivar after supplementation with15 and
30% chickpea was significantly (P ≤ 0.05) increased to 11.78 and
14.55%, respectively. The protein digestibility also increased after
fermentation from 13.35 to 30.59 and 40.56% for the supplements,
respectively. Further increment in protein content and digestibility
was observed when supplemented and unsupplemented samples were
fermented for different periods of time. Cooking of fermented
samples was found to increase the protein content slightly and
decreased digestibility for both supplements. Amino acid content of
fermented and fermented and cooked supplements was determined.
Supplementation was found to increase the lysine and therionine
content. Cooking following fermentation decreased lysine,
isoleucine, valine and sulfur containg amino acids.
Abstract: Salinity is a measure of the amount of salts in the
water. Total Dissolved Solids (TDS) as salinity parameter are often
determined using laborious and time consuming laboratory tests, but
it may be more appropriate and economical to develop a method
which uses a more simple soil salinity index. Because dissolved ions
increase salinity as well as conductivity, the two measures are
related. The aim of this research was determine of constant
coefficients for predicting of Total Dissolved Solids (TDS) based on
Electrical Conductivity (EC) with Statistics of Correlation
coefficient, Root mean square error, Maximum error, Mean Bias
error, Mean absolute error, Relative error and Coefficient of residual
mass. For this purpose, two experimental areas (S1, S2) of Khuzestan
province-IRAN were selected and four treatments with three
replications by series of double rings were applied. The treatments
were included 25cm, 50cm, 75cm and 100cm water application. The
results showed the values 16.3 & 12.4 were the best constant
coefficients for predicting of Total Dissolved Solids (TDS) based on
EC in Pilot S1 and S2 with correlation coefficient 0.977 & 0.997 and
191.1 & 106.1 Root mean square errors (RMSE) respectively.
Abstract: The main objective of this research was to investigate
the biosorption capacity for biofilms of sulphate reducing bacteria
(SRB) to remove heavy metals, such as Zn, Pb and Cd from
rainwater using laboratory-scale reactors containing mixed support
media. Evidence showed that biosorption had contributed to removal
of heavy metals including Zn, Pb and Cd in presence of SRB and
SRB were also found in the aqueous samples from reactors.
However, the SRB and specific families (Desulfobacteriaceae and
Desulfovibrionaceae) were found mainly in the biomass samples
taken from all reactors at the end of the experiment. EDX-analysis
of reactor solids at end of experiment showed that heavy metals Zn,
Pb and Cd had also accumulated in these precipitates.
Abstract: The Beshar River is one aquatic ecosystem,which is
affected by pollutants. This study was conducted to evaluate the
effects of human activities on the water quality of the Beshar river.
This river is approximately 190 km in length and situated at the
geographical positions of 51° 20' to 51° 48' E and 30° 18' to 30° 52'
N it is one of the most important aquatic ecosystems of Kohkiloye
and Boyerahmad province next to the city of Yasuj in southern Iran.
The Beshar river has been contaminated by industrial, agricultural
and other activities in this region such as factories, hospitals,
agricultural farms, urban surface runoff and effluent of wastewater
treatment plants. In order to evaluate the effects of these pollutants
on the quality of the Beshar river, five monitoring stations were
selected along its course. The first station is located upstream of
Yasuj near the Dehnow village; stations 2 to 4 are located east, south
and west of city; and the 5th station is located downstream of Yasuj.
Several water quality parameters were sampled. These include pH,
dissolved oxygen, biological oxygen demand (BOD), temperature,
conductivity, turbidity, total dissolved solids and discharge or flow
measurements. Water samples from the five stations were collected
and analysed to determine the following physicochemical
parameters: EC, pH, T.D.S, T.H, No2, DO, BOD5, COD during 2008
to 2009. The study shows that the BOD5 value of station 1 is at a
minimum (1.5 ppm) and increases downstream from stations 2 to 4 to
a maximum (7.2 ppm), and then decreases at station 5. The DO
values of station 1 is a maximum (9.55 ppm), decreases downstream
to stations 2 - 4 which are at a minimum (3.4 ppm), before increasing
at station 5. The amount of BOD and TDS are highest at the 4th
station and the amount of DO is lowest at this station, marking the
4th station as more highly polluted than the other stations. The
physicochemical parameters improve at the 5th station due to
pollutant degradation and dilution. Finally the point and nonpoint
pollutant sources of Beshar river were determined and compared to
the monitoring results.
Abstract: Intermittent aeration process can be easily applied on
the existing activated sludge system and is highly reliable against the loading changes. It can be operated in a relatively simple way as well.
Since the moving-bed biofilm reactor method processes pollutants by attaching and securing the microorganisms on the media, the process
efficiency can be higher compared to the suspended growth biological
treatment process, and can reduce the return of sludge. In this study,
the existing intermittent aeration process with alternating flow being
applied on the oxidation ditch is applied on the continuous flow stirred tank reactor with advantages from both processes, and we would like
to develop the process to significantly reduce the return of sludge in the clarifier and to secure the reliable quality of treated water by
adding the moving media. Corresponding process has the appropriate
form as an infrastructure based on u- environment in future u- City and
is expected to accelerate the implementation of u-Eco city in conjunction with city based services. The system being conducted in a
laboratory scale has been operated in HRT 8hours except for the final
clarifier and showed the removal efficiency of 97.7 %, 73.1 % and 9.4
% in organic matters, TN and TP, respectively with operating range of
4hour cycle on system SRT 10days. After adding the media, the removal efficiency of phosphorus showed a similar level compared to
that before the addition, but the removal efficiency of nitrogen was
improved by 7~10 %. In addition, the solids which were maintained in
MLSS 1200~1400 at 25 % of media packing were attached all onto the
media, which produced no sludge entering the clarifier. Therefore, the
return of sludge is not needed any longer.
Abstract: Dense slurry flow through centrifugal pump casing
has been modeled using the Eulerian-Eulerian approach with
Eulerian multiphase model in FLUENT 6.1®. First order upwinding
is considered for the discretization of momentum, k and ε terms.
SIMPLE algorithm has been applied for dealing with pressurevelocity
coupling. A mixture property based k-ε turbulence model
has been used for modeling turbulence. Results are validated first
against mesh independence and experiments for a particular set of
operational and geometric conditions. Parametric analysis is then
performed to determine the effect on important physical quantities
viz. solid velocities, solid concentration and solid stresses near the
wall with various operational geometric conditions of the pump.
Abstract: The changes in quality properties and nutritional
components in two fermented mugworts (Artemisia capillaries
Thumberg, Artemisiaeasiaticae Nakai) were characterized followed
by the rapid pattern analysis of volatile flavor compounds by Electric
Nose based on SAW(Surface Acoustic Wave) sensor in GC system.
There were remarkable decreases in the pH and small changes in the
total soluble solids after fermentation. The L (lightness) and b
(yellowness) values in Hunter's color system were shown to be
decreased, whilst the a (redness) value was increased by fermentation.
The HPLC analysis demonstrated that total amino acids were
increased in quantity and the essential amino acids were contained
higher in A. asiaticaeNakai than in A. capillaries Thumberg. While
the total polyphenol contents were not affected by fermentation, the
total sugar contents were dramatically decreased. Scopoletinwere
highly abundant in A. capillarisThumberg, however, it was not
detected in A. asiaticaeNakai. Volatile flavor compounds by Electric
Nose showed that the intensity of several peaks were increased much
and seven additional flavor peaks were newly produced after
fermentation. The flavor differences of two mugworts were clearly
distinguished from the image patterns of VaporPrintTM which indicate
that the fermentation enables the two mugworts to have subtle flavor
differences.
Abstract: The present work compares the performance of three
turbulence modeling approach (based on the two-equation k -ε
model) in predicting erosive wear in multi-size dense slurry flow
through rotating channel. All three turbulence models include
rotation modification to the production term in the turbulent kineticenergy
equation. The two-phase flow field obtained numerically
using Galerkin finite element methodology relates the local flow
velocity and concentration to the wear rate via a suitable wear model.
The wear models for both sliding wear and impact wear mechanisms
account for the particle size dependence. Results of predicted wear
rates using the three turbulence models are compared for a large
number of cases spanning such operating parameters as rotation rate,
solids concentration, flow rate, particle size distribution and so forth.
The root-mean-square error between FE-generated data and the
correlation between maximum wear rate and the operating
parameters is found less than 2.5% for all the three models.
Abstract: The mechanical properties of granular solids are
dependent on the flow of stresses from one particle to another
through inter-particle contact. Although some experimental methods
have been used to study the inter-particle contacts in the past,
preliminary work with these techniques indicated that they do not
have the necessary resolution to distinguish between those contacts
that transmit the load and those that do not, especially for systems
with a wide distribution of particle sizes. In this research, computer
simulations are used to study the nature and distribution of contacts
in a compact with wide particle size distribution, representative of
aggregate size distribution used in asphalt pavement construction.
The packing fraction, the mean number of contacts and the
distribution of contacts were studied for different scenarios. A
methodology to distinguish and compute the fraction of load-bearing
particles and the fraction of space-filling particles (particles that do
not transmit any force) is needed for further investigation.
Abstract: Estimation of stormwater pollutants is a pre-requisite
for the protection and improvement of the aquatic environment and
for appropriate management options. The usual practice for the
stormwater quality prediction is performed through water quality
modeling. However, the accuracy of the prediction by the models
depends on the proper estimation of model parameters. This paper
presents the estimation of model parameters for a catchment water
quality model developed for the continuous simulation of stormwater
pollutants from a catchment to the catchment outlet. The model is
capable of simulating the accumulation and transportation of the
stormwater pollutants; suspended solids (SS), total nitrogen (TN) and
total phosphorus (TP) from a particular catchment. Rainfall and water
quality data were collected for the Hotham Creek Catchment (HTCC),
Gold Coast, Australia. Runoff calculations from the developed model
were compared with the calculated discharges from the widely used
hydrological models, WBNM and DRAINS. Based on the measured
water quality data, model water quality parameters were calibrated
for the above-mentioned catchment. The calibrated parameters are
expected to be helpful for the best management practices (BMPs)
of the region. Sensitivity analyses of the estimated parameters were
performed to assess the impacts of the model parameters on overall
model estimations of runoff water quality.
Abstract: The present study was designed to demonstrate the seasonal variations in physico-chemical parameters of fish farm at Govt. Nursery Unit, Muzaffargarh, Department of Fisheries Govt. of Punjab, Pakistan for a period of eight months from January to August 2008. Water samples were collected on fifteen days basis and have been analyzed for estimation of Air temperature, Water temperature, Light penetration, pH, Total dissolved oxygen, Clouds, Carbonates, Bicarbonates, Total carbonates, Total dissolved solids, Chlorides, Calcium and Hardness. Seasonal fluctuations were observed in all the physico-chemical parameters of fish farm. The overall physicochemical parameters of fish pond water remained within the tolerable range throughout the study period.
Abstract: A novel sponge submerged membrane bioreactor
(SSMBR) was developed to effectively remove organics and
nutrients from wastewater. Sponge is introduced within the SSMBR
as a medium for the attached growth of biomass. This paper evaluates
the effects of new and acclimatized sponges for dissolved organic
carbon (DOC) removal from wastewater at different mixed liquor
suspended solids- (MLSS) concentration of the sludge. It was
observed in a series of experimental studies that the acclimatized
sponge performed better than the new sponge whilst the optimum
DOC removal could be achieved at 10g/L of MLSS with the
acclimatized sponge. Moreover, the paper analyses the relationships
between the MLSSsponge/MLSSsludge and the DOC removal efficiency
of SSMBR. The results showed a non-linear relationship between the
biomass parameters of the sponge and the sludge, and the DOC
removal efficiency of SSMBR. A second-order polynomial function
could reasonably represent these relationships.