Abstract: This research tries to analyze the role that knowledge
about foreign markets has in increasing firms- exports in clustered
spaces. We consider two interrelated sources of knowledge: firms-
direct experience and indirect experience from other clustered firms –
export externalities. In particular, it is proposed that firms would
improve their export performance by accessing to export externalities
if they have some previous direct experience that allows them to
identify, understand and exploit them. Also, we propose that this
positive influence of previous direct experience on export
externalities keeps only up to a point, where it becomes negative,
creating an inverted “U" shape. Empirical evidence gathered among
wine producers located in La Rioja tends to confirm that firms enjoy
of export externalities if they have export experience along several
years and countries increase their export performance. While this
relationship becomes less relevant as they develop a higher
experience, we could not confirm the existence of a curvilinear
relationship in their influence on export externalities and export
performance.
Abstract: This study evaluates the performance of horizontal
subsurface flow constructed wetland (HSSF-CW) for the removal of
chlorinated resin and fatty acids (RFAs) from pulp and paper mill
wastewater. The dimensions of the treatment system were 3.5 m x 1.5
m x 0.28 m with surface area of 5.25 m2, filled with fine sand and
gravel. The cell was planted with an ornamental plant species Canna
indica. The removal efficiency of chlorinated RFAs was in the range
of 92-96% at the hydraulic retention time (HRT) of 5.9 days. Plant
biomass and soil (sand and gravel) were analyzed for chlorinated
RFAs content. No chlorinated RFAs were detected in plant biomass
but detected in soil samples. Mass balance studies of chlorinated
RFAs in HSSF-CW were also carried out.
Abstract: In this study the mixed convection heat transfer in a
coil-in-shell heat exchanger for various Reynolds numbers and
various dimensionless coil pitch was experimentally investigated.
The experiments were conducted for both laminar and turbulent flow
inside coil and the effects of coil pitch on shell-side heat transfer
coefficient of the heat exchanger were studied. The particular
difference in this study in comparison with the other similar studies
was the boundary conditions for the helical coils. The results indicate
that with the increase of coil pitch, shell-side heat transfer coefficient
is increased.
Abstract: This paper presents dynamic voltage collapse prediction on an actual power system using support vector machines.
Dynamic voltage collapse prediction is first determined based on the PTSI calculated from information in dynamic simulation output. Simulations were carried out on a practical 87 bus test system by considering load increase as the contingency. The data collected from the time domain simulation is then used as input to the SVM in which support vector regression is used as a predictor to determine the
dynamic voltage collapse indices of the power system. To reduce training time and improve accuracy of the SVM, the Kernel function type and Kernel parameter are considered. To verify the
effectiveness of the proposed SVM method, its performance is compared with the multi layer perceptron neural network (MLPNN). Studies show that the SVM gives faster and more accurate results for dynamic voltage collapse prediction compared with the MLPNN.
Abstract: The communication networks development and
advancement during two last decades has been toward a single goal
and that is gradual change from circuit-switched networks to packed
switched ones. Today a lot of networks operates are trying to
transform the public telephone networks to multipurpose packed
switch. This new achievement is generally called "next generation
networks". In fact, the next generation networks enable the operators
to transfer every kind of services (sound, data and video) on a
network. First, in this report the definition, characteristics and next
generation networks services and then ad-hoc networks role in the
next generation networks are studied.
Abstract: The health record in the Electronic Health Record
(EHR) system is more sensitive than demographic. It raises the
important issue for the EHR requirement in privacy, security, audit
trail, patient access, and archiving and data retention. The studies
about the EHR system security are deficient. The aim of this study is to
build a security environment for the EHR system by Integrating the
Healthcare Enterprise (IHE) Audit Trail and Node Authentication
Security (ATNA) profile. The CDAs can be access in a secure EHR
environment.
Abstract: Following the laser ablation studies leading to a
theory of nuclei confinement by a Debye layer mechanism, we
present here numerical evaluations for the known stable nuclei where
the Coulomb repulsion is included as a rather minor component
especially for lager nuclei. In this research paper the required
physical conditions for the formation and stability of nuclei
particularly endothermic nuclei with mass number greater than to
which is an open astrophysical question have been investigated.
Using the Debye layer mechanism, nuclear surface energy, Fermi
energy and coulomb repulsion energy it is possible to find conditions
under which the process of nucleation is permitted in early universe.
Our numerical calculations indicate that about 200 second after the
big bang at temperature of about 100 KeV and subrelativistic region
with nucleon density nearly equal to normal nuclear density namely,
10cm all endothermic and exothermic nuclei have been
formed.
Abstract: As a part of an evaluation system for R&D programs,
the Korean Government has applied the preliminary feasibility study
to new government R&D program plans. Basically, the fundamental purpose of the preliminary feasibility study is to decide that the
government will either do or do not invest in a new R&D Program. Additionally, the preliminary feasibility study can contribute to the
improvement of R&D program plans. For example, 2 cases of new
R&D program plans applied to the study are explained in this paper and there are expectations that these R&D programs would yield better
performance than without the study. It is thought that the important point of the preliminary feasibility study is not only the effective
decision making process of R&D program but also the opportunity to improve R&D program plan actually.
Abstract: A method based on the power series solution is proposed to solve the natural frequency of flapping vibration for the rotating inclined Euler beam with constant angular velocity. The vibration of the rotating beam is measured from the position of the corresponding steady state axial deformation. In this paper the governing equations for linear vibration of a rotating Euler beam are derived by the d'Alembert principle, the virtual work principle and the consistent linearization of the fully geometrically nonlinear beam theory in a rotating coordinate system. The governing equation for flapping vibration of the rotating inclined Euler beam is linear ordinary differential equation with variable coefficients and is solved by a power series with four independent coefficients. Substituting the power series solution into the corresponding boundary conditions at two end nodes of the rotating beam, a set of homogeneous equations can be obtained. The natural frequencies may be determined by solving the homogeneous equations using the bisection method. Numerical examples are studied to investigate the effect of inclination angle on the natural frequency of flapping vibration for rotating inclined Euler beams with different angular velocity and slenderness ratio.
Abstract: In this paper, the 1-D conduction-radiation problem is solved by the lattice Boltzmann method. The effects of various parameters such as the scattering albedo, the conduction–radiation parameter and the wall emissivity are studied. In order to check on the accuracy of the numerical technique employed for the solution of the considered problem, the present numerical code was validated with the published study. The found results are in good agreement with those published
Abstract: The influences of pulsed electric fields on early
physiological development in Arabidopsis thaliana were studied.
Inside a 4-mm electroporation cuvette, pre-germination seeds were
subjected to high-intensity, nanosecond electrical pulses generated
using laboratory-assembled pulsed electric field system. The field
strength was varied from 5 to 20 kV.cm-1 and the pulse width and the
pulse number were maintained at 10 ns and 100, respectively,
corresponding to the specific treatment energy from 300 J.kg-1 to 4.5
kJ.kg-1. Statistical analyses on the average leaf area 5 and 15 days
following pulsed electric field treatment showed that the effects
appear significant the second week after treatments with a maximum
increase of 80% compared to the control (P < 0.01).
Abstract: This paper studies the application of a variety of
sawdust materials in the production of lightweight insulating bricks.
First, the mineralogical and chemical composition of clays was determined. Next, ceramic bricks were fabricated with different
quantities of materials (3–6 and 9 wt. % for sawdust, 65 wt. % for grey clay, 24–27 and 30 wt. % for yellow clay and 2 wt% of tuff).
These bricks were fired at 800 and 950 °C. The effect of adding this sawdust on the technological behaviour of the brick was assessed by
drying and firing shrinkage, water absorption, porosity, bulk density
and compressive strength. The results have shown that the optimum
sintering temperature is 950 °C. Below this temperature, at 950 °C,
increased open porosity was observed, which decreased the compressive strength of the bricks. Based on the results obtained, the
optimum amounts of waste were 9 wt. % sawdust of eucalyptus, 24 wt. % shaping moisture and 1.6 particle size diameter. These percentages produced bricks whose mechanical properties were
suitable for use as secondary raw materials in ceramic brick
production.
Abstract: Technology transfer of renewable energy technologies is very often unsuccessful in the developing world. Aside from challenges that have social, economic, financial, institutional and environmental dimensions, technology transfer has generally been misunderstood, and largely seen as mere delivery of high tech equipment from developed to developing countries or within the developing world from R&D institutions to society. Technology transfer entails much more, including, but not limited to: entire systems and their component parts, know-how, goods and services, equipment, and organisational and managerial procedures. Means to facilitate the successful transfer of energy technologies, including the sharing of lessons are subsequently extremely important for developing countries as they grapple with increasing energy needs to sustain adequate economic growth and development. Improving the success of technology transfer is an ongoing process as more projects are implemented, new problems are encountered and new lessons are learnt. Renewable energy is also critical to improve the quality of lives of the majority of people in developing countries. In rural areas energy is primarily traditional biomass. The consumption activities typically occur in an inefficient manner, thus working against the notion of sustainable development. This paper explores the implementation of technology transfer in the developing world (sub-Saharan Africa). The focus is necessarily on RETs since most rural energy initiatives are RETs-based. Additionally, it aims to highlight some lessons drawn from the cited RE projects and identifies notable differences where energy technology transfer was judged to be successful. This is done through a literature review based on a selection of documented case studies which are judged against the definition provided for technology transfer. This paper also puts forth research recommendations that might contribute to improved technology transfer in the developing world. Key findings of this paper include: Technology transfer cannot be complete without satisfying pre-conditions such as: affordability, maintenance (and associated plans), knowledge and skills transfer, appropriate know how, ownership and commitment, ability to adapt technology, sound business principles such as financial viability and sustainability, project management, relevance and many others. It is also shown that lessons are learnt in both successful and unsuccessful projects.
Abstract: Deep cold rolling (DCR) is a cold working process, which easily produces a smooth and work-hardened surface by plastic deformation of surface irregularities. In the present study, the influence of main deep cold rolling process parameters on the surface roughness and the hardness of AISI 4140 steel were studied by using fractional factorial design of experiments. The assessment of the surface integrity aspects on work material was done, in terms of identifying the predominant factor amongst the selected parameters, their order of significance and setting the levels of the factors for minimizing surface roughness and/or maximizing surface hardness. It was found that the ball diameter, rolling force, initial surface roughness and number of tool passes are the most pronounced parameters, which have great effects on the work piece-s surface during the deep cold rolling process. A simple, inexpensive and newly developed DCR tool, with interchangeable collet for using different ball diameters, was used throughout the experimental work presented in this paper.
Abstract: In order to study of hydropriming and halopriming on
germination and early growth stage of wheat (Triticum aestivum) an
experiment was carried out in laboratory of the Department of
Agronomy and Plant breeding, Shahrood University of Technology.
Seed treatments consisted of T1: control (untreated seeds), T2:
soaking in distilled water for 18 h (hydropriming). T3: soaking in -
1.2 MPa solution of CaSO4 for 36 h (halopriming). Germination and
early seedling growth were studied using distilled water (control) and
under osmotic potentials of -0.4, -0.8 and -1.2 MPa for NaCl and
polyethylene glycol (PEG 6000), respectively. Results showed that
Hydroprimed seeds achieved maximum germination seedling dry
weight, especially during the higher osmotic potentials. Minimum
germination was recorded at untreated seeds (control) followed by
osmopriming. Under high osmotic potentials, hydroprimed seeds had
higher GI (germination index) as compared to haloprimed or
untreated seeds. Interaction effect of seed treatment and osmotic
potential significantly affected the seedling vigour index (SVI).
Abstract: Sol-gel immobilization of enzymes, which can improve considerably their properties, is now one of the most used techniques. By deposition of the entrapped lipase on a solid support, a new and improved biocatalyst was obtained, which can be used with excellent results in acylation reactions. In this paper, lipase B from Candida antarctica was double immobilized on different adsorbents. These biocatalysts were employed in the kinetic resolution of several aliphatic secondary alcohols in organic medium. High total recovery yields of enzymatic activity, up to 560%, were obtained. For all the studied alcohols the enantiomeric ratios E were over 200. The influence of the reaction medium was studied for the kinetic resolution of 2-pentanol.
Abstract: Electrolytic dissolution characteristics of UO2 and
SIMFUEL electrodes were studied at several potentials in carbonate
solutions of a high concentration at several pHs. The electrolytic
uranium dissolution was much affected by a corrosion product of
UO2CO3 generated at the electrode during the dissolution in carbonate
solution. The corrosion product distorted the voltammogram at UO2
and SIMFUEL electrodes in the potential region of oxygen evolution
and increased the overpotential of oxygen evolution at the electrode.
The effective dissolution in a carbonate solution could be obtained at
an applied potential such as +4 V (vs SSE) or more which had an
overpotential of oxygen evolution high enough to rupture the
corrosion product on the electrode surface.
Abstract: Restructured electricity markets may provide
opportunities for producers to exercise market power maintaining
prices in excess of competitive levels. In this paper an oligopolistic
market is presented that all Generation Companies (GenCos) bid in a
Cournot model. Genetic algorithm (GA) is applied to obtain
generation scheduling of each GenCo as well as hourly market
clearing prices (MCP). In order to consider network constraints a
multiperiod framework is presented to simulate market clearing
mechanism in which the behaviors of market participants are
modelled through piecewise block curves. A mixed integer linear
programming (MILP) is employed to solve the problem. Impacts of
market clearing process on participants- characteristic and final
market prices are presented. Consequently, a novel multi-objective
model is addressed for security constrained optimal bidding strategy
of GenCos. The capability of price-maker GenCos to alter MCP is
evaluated through introducing an effective-supply curve. In addition,
the impact of exercising market power on the variation of market
characteristics as well as GenCos scheduling is studied.
Abstract: In the micro and nano-technology industry, the
«clean-rooms» dedicated to manufacturing chip, are equipped with
the most sophisticated equipment-tools. There use a large number of
resources in according to strict specifications for an optimum
working and result. The distribution of «utilities» to the production is
assured by teams who use a supervision tool.
The studies show the interest to control the various parameters of
production or/and distribution, in real time, through a reliable and
effective supervision tool. This document looks at a large part of the
functions that the supervisor must assure, with complementary
functionalities to help the diagnosis and simulation that prove very
useful in our case where the supervised installations are complexed
and in constant evolution.
Abstract: Polyurethane foams (PUF) has been prepared from
vegetable; soybean based polyols. They were characterized into
flexible and semi rigid polyurethane foam. This work is directed to
production of flexible polyurethane foams by a process involving the
reaction of mixture of 2,4- and 2,6-Toluene di Isocyanate isomers,
with portion of to blends of soy polyols with petroleum polyol in the
presence of other ingredients such as blowing agents, silicone
surfactants and accelerating agents. Additon of chain extender
improves the property then further decreases the properties on further
addition of the same. The objective of this work was to study the
effect of chain extender and role of phosphoric acid catalyst to the
final properties and correlate the morphology image with mechanical
properties of these foams.