Abstract: Due to side-peaks of autocorrelation function, the binary offset carrier (BOC) signal acquisition suffers from an ambiguity when one of the side-peaks is acquired. In this paper, we first analyze that the BOC autocorrelation is made up of the sum of subcorrelations, and then, remove the side-peaks causing the ambiguity by recombining the sub-correlations. The proposed scheme is shown to remove the side-peaks completely. From numerical results, it is confirmed that the proposed scheme outperforms the conventional schemes in terms of the receiver operating characteristic and mean acquisition time.
Abstract: Carbon dioxide has been well associated with greenhouse effect, and due to its corrosive nature it is an undesirable compound. A variety of physical-chemical processes are available for the removal of carbon dioxide. Previous attempts in this field have established alkanolamine group has the capability to remove carbon dioxide. So, this study combined the polymeric membrane and alkanolamine solutions to fabricate the amine polymeric membrane (APM) to remove carbon dioxide (CO2). This study entails the effect of three types of amines, monoethanolamine (MEA), diethanolamine (DEA), and methyldiethanolamine (MDEA). The effect of each alkanolamine group on the morphology and performance of polyether sulfone (PES) polymeric membranes was studied. Flat sheet membranes were fabricated by solvent evaporation method by adding polymer and different alkanolamine solutions in the N-Methyl-2-pyrrolidone (NMP) solvent. The final membranes were characterized by using Field Emission Electron Microscope (FESEM), Fourier Transform Infrared (FTIR), and Thermo-Gravimetric Analysis (TGA). The membrane separation performance was studied. The PES-DEA and PES-MDEA membrane has good ability to remove carbon dioxide.
Abstract: Field study was conducted to determine the post field soil fertility status responses of pawpaw (Carica papaya L.) var. homestead selection and sunrise-solo orchards to organo-mineral fertilizer (OMF) rates applied at 10, 20 40 t/ha where both the zero t/ha OMF and NPK 15:15:15 at 50 g/plant/month served as control. The result showed that all pawpaw orchards treated with OMF rates recorded significantly (p≤0.01) higher % P, % K, Na and % organic matter in soil compared to applied NPK which recorded lower Na. However, while orchards plated with sole pawpaw were higher in soil bulk density (SBD), orchards with homestead mixture were lower in SBD and significantly lower % organic matter compared to obtainable under sunrise crop mixture which recorded lower Na and Mg. In conclusion, as a result of loosening effect on soil particles, the homestead pawpaw probably due to more rooting activities as well as the addition of organic fertilizer to soils both had significant influence leading to lower SBD.
Abstract: Discrete wavelet transform (DWT) has been widely adopted in biomedical signal processing for denoising, compression
and so on. Choosing a suitable decomposition level (DL) in DWT is of paramount importance to its performance. In this paper, we propose to exploit sparseness of the transformed signals to determine the appropriate DL. Simulation results have shown that the sparseness of transformed signals after DWT increases with the increasing DLs. Additional Monte-Carlo simulation results have verified the effectiveness of sparseness measure in determining the DL.
Abstract: Fly ash is a waste material of coal firing thermal
plants that is released from thermal power plants. It was defined as
very fine particles that are drifted upward which are taken up by the
flue gases. The emerging amount of fly ash in the world is
approximately 600 million tons per year. In our country, it is
expected that will be occurred 50 million tons of waste ash per year
until 2020. The fly ashes can be evaluated by using as adsorbent
material. The purpose of this study is to investigate the possibility of
use of various fly ashes (Tuncbilek, Catalagzi, Orhaneli) like lowcost
adsorbents for heavy metal adsorption. First of all, fly ashes
were characterized. For this purpose; analyses such as XRD, XRF,
SEM and FT-IR were performed.
Abstract: Combustion of fuels in industrial and transport sector has lead to an alarming release of polluting gases to the atmosphere. Carbon monoxide is one such pollutant, which is formed as a result of incomplete oxidation of the fuel. In order to analyze the effect of catalyst on the reduction of CO emissions to the atmosphere, two catalysts Mn2O3 and Hopcalite are considered. A model was formed based on mass and energy balance equations. Results show that Hopcalite catalyst as compared to Mn2O3 catalyst helped in faster conversion of the polluting gas as the operating temperature of the hopcalite catalyst is much lower as compared to the operating temperature of Mn2O3 catalyst.
Abstract: Different vegetable oil based biodiesel (FAMES) were prepared by alkaline transesterification using refined oils as well as waste frying oil (WFO). Methanol and sodium hydroxide are used as catalyst under similar reaction conditions. To ensure the quality of biodiesel produced, a series of different ASTM Standard tests were carried out. In this context, various testwere done including viscosity, carbon residue, specific gravity, corrosion test, flash point, cloud point and pour point. Results revealed that characteristics of biodiesel depend on the feedstock and it is far better than petroleum diesel.
Abstract: In this paper we use low frequency noise analysis to understand and map the current conduction path in a multi gate junctionless FinFET. The device used in this study behaves as a gated resistor and shows excellent short channel effect suppression due to its multi gate structure. Generally for a bulk conduction device like the junctionless device studied in this work, the low frequency noise can be modelled using the mobility fluctuation model; however for this device we can also see the effect of carrier fluctuations on the LFN characteristic. The noise characteristic at different gate bias and also the possible location of the traps is explained.
Abstract: The aim of this paper is to examine the relationship among CO2 per capita emissions, energy consumption, economic growth and bilateral trade between Singapore and Malaysia for the 1970-2011 period. ARDL model and Granger causality tests are employed for the analysis. Results of bound F-statistics suggest that long-run relationship exists between CO2 per capita (PCO2) and its determinants. The EKC hypothesis is not supported in Malaysia. Carbon emissions are mainly determined by energy consumption in the short and long run. While, exports to Singapore is a significant variable in explaining PCO2 emissions in Malaysia in long-run. Furthermore, we find a unidirectional causal relationship running from economic growth to PCO2 emissions.
Abstract: The influence of copper and zinc supplements on milk
production performances and health indicators was tested in a 20-
week feeding trial, with 40 Holstein-Friesian lactating cows, devided
in four groups (copper, zinc, copper-zinc and control). Correlations of
the Cu and Zn plasma values with some animal performance criteria
of health (body condition score and somatic cell counts) and
production (milk yield, peak milk yield, fat and crude protein
content) were done. During the 140 days of the experiment, the two
added minerals caused a statistically significant increase (p < 0.05) of
their plasma values after the peak of the cows’ lactations. It was also
observed that subjects that have received copper and zinc
supplements had the lowest number of somatic cell counts in milk.
The Pearson correlation test showed a positive corellation (p = 0.007,
r = + 0.851) between the plasma Zn and the milk production. The
improvement of the nutritional status improved the milk production
performances of the cows as well as their health performances.
Abstract: Image registration is the process of establishing point
by point correspondence between images obtained from a same
scene. This process is very useful in remote sensing, medicine,
cartography, computer vision, etc. Then, the task of registration is to
place the data into a common reference frame by estimating the
transformations between the data sets. In this work, we develop a
rigid point registration method based on the application of genetic
algorithms and Hausdorff distance. First, we extract the feature points
from both images based on the algorithm of global and local
curvature corner. After refining the feature points, we use Hausdorff
distance as similarity measure between the two data sets and for
optimizing the search space we use genetic algorithms to achieve
high computation speed for its inertial parallel. The results show the
efficiency of this method for registration of satellite images.
Abstract: This paper addresses the analysis of the interference between complementary ground component (CGC) base station and mobile earth station (MES). In the frequency sharing scenario between CGC base station and MES, the interference from the adjacent beams must be considered. In this paper, we estimated the interference to MES of an integrated satellite system and the result is presented as the carrier to interference ratio(C/I) with respect to the number of CGC base station in the adjacent beam and the ratio of satellite beam center radius to the total beam radius (R1/R). By using these results, we can determine the minimum separation distance between the CGC base stations of adjacent beam and MES for compatibility. This result can be applied to the CGC base station of an integrated satellite system for the effective frequency sharing.
Abstract: This paper presents the study of strengthening R/C
beams with large circular and square opening located at flexure zone
by Carbon Fiber Reinforced Polymer (CFRP) laminates. A total of
five beams were tested to failure under four point loading to
investigate the structural behavior including crack patterns, failure
mode, ultimate load and load deflection behaviour. Test results show
that large opening at flexure reduces the beam capacity and stiffness;
and increases cracking and deflection. A strengthening configuration
was designed for each un-strengthened beams based on their
respective crack patterns. CFRP laminates remarkably restore the
beam capacity of beam with large circular opening at flexure location
while 10% re-gain of beam capacity with square opening. The use of
CFRP laminates with the designed strengthening configuration could
significantly reduce excessive cracking and deflection and increase
the ultimate capacity and stiffness of beam.
Abstract: This study presents a new method for detecting the
cutting tool wear based on the measured cutting force signals using
the regression model and I-kaz method. The detection of tool wear
was done automatically using the in-house developed regression
model and 3D graphic presentation of I-kaz 3D coefficient during
machining process. The machining tests were carried out on a CNC
turning machine Colchester Master Tornado T4 in dry cutting
condition, and Kistler 9255B dynamometer was used to measure the
cutting force signals, which then stored and displayed in the DasyLab
software. The progression of the cutting tool flank wear land (VB)
was indicated by the amount of the cutting force generated. Later, the
I-kaz was used to analyze all the cutting force signals from beginning
of the cut until the rejection stage of the cutting tool. Results of the IKaz
analysis were represented by various characteristic of I-kaz 3D
coefficient and 3D graphic presentation. The I-kaz 3D coefficient
number decreases when the tool wear increases. This method can be
used for real time tool wear monitoring.
Abstract: Purpose: To compare attitudes and perceptions of
Israeli native born mothers versus former Soviet Union (FSU)
immigrant mothers regarding the physical health of their infant.
Methodology: cross-sectional design. A convenience sample of 50
participants was recruited by face to face and snowball technique. A
questionnaire was constructed according to the instructions of the
Ministry of Health for the care and treatment of infants. The main
areas explored were: sources of knowledge that the young mother
acquired regarding the care of her infant, ways of caring for the
infant, hygiene and sanitary habits, and the pattern of referral to
health professionals. The last topic relates to emotions mothers might
experience towards their infant.
Results: Mothers from both cultural groups present some similar
caring behaviors, which may express a universal aspect of mothers'
behavior towards their infants. However, immigrant mothers differ
significantly from native born by relying less on their mothers' and
grandmothers' experience, they wean their infants from diapers
earlier, they are stricter about hygiene and sanitary habits and they
tend to consult a physician when their infant has low fever. Native
born and immigrant mothers differ in their expressions of pride and
wonder. Immigrant mothers report of a lesser degree of these
emotions towards their infants than native born mothers.
Conclusion: The theoretical model of socialization and
acculturation of immigrant mothers is employed as an explanatory
model for the current findings Young immigrant mothers undergo a
complex acculturation process and adapt behavioral patterns in
various areas to comply with Israeli norms and values, demonstrating
assimilation. In other areas they adhere to the norms of their original
culture.
Abstract: Taiwan was the first country in Asia to announce
“Nuclear-Free Homeland" in 2002. In 2008, the new government
released the Sustainable Energy Policy Guidelines to lower the
nationwide CO2 emissions some time between 2016 and 2020 back to
the level of year 2008, further abatement of CO2 emissions is planed in
year 2025 when CO2 emissions will decrease to the level of year 2000.
Besides, under consideration of the issues of energy, environment and
economics (3E), the new government declared that the nuclear power
is a carbon-less energy option. This study analyses the effects of
nuclear power generation for CO2 abatement scenarios in Taiwan. The
MARKAL-MACRO energy model was adopted to evaluate economic
impacts and energy deployment due to life extension of existing
nuclear power plants and build new nuclear power units in CO2
abatement scenarios. The results show that CO2 abatement effort is
expensive. On the other hand, nuclear power is a cost-effective choice.
The GDP loss rate in the case of building new nuclear power plants is
around two thirds of the Nuclear-Free Homeland case. Nuclear power
generation has the capacity to provide large-scale CO2 free electricity.
Therefore, the results show that nuclear power is not only an option for
Taiwan, but also a requisite for Taiwan-s CO2 reduction strategy.
Abstract: The adsorption of bovine serum albumin (BSA), immunoglobulin G (IgG) and fibrinogen (Fgn) on fluorinated selfassembled monolayers have been studied using time of flight secondary ion mass spectrometry (ToF-SIMS) and Spectroscopic Ellipsometry (SE). The objective of the work has to establish the utility of ToF-SIMS for the determination of the amount of protein adsorbed on the surface. Quantification of surface adsorbed proteins was carried out using SE and a good correlation between ToF-SIMS results and SE was achieved. The surface distribution of proteins were also analysed using Atomic Force Microscopy (AFM). We show that the surface distribution of proteins strongly affect the ToFSIMS results.
Abstract: Thermite welding is mainly used in world. The
reasons why the thermite welding method is widely used are
that the equipment has good mobility and total working time
of that is shorter than that of the enclosed arc welding method
on site. Moreover, the operating skill, which required for
thermite welding, is less than that of for enclosed arc welding.
In the present research work, heat treatment and combined
'expulsion and heat treatment' techniques were used improve
the mechanical properties and weldment structure. The
specimens were cut in the transverse direction from expulsion
with Heat treated and heat treated Thermite Welded rails.
Specimens were prepared according to AWS standard and
subjected to tensile test, Impact test and hardness and their
results were tabulated. Microstructural analysis was carried
out with the help of SEM. Then analyze to effect of heat
treated and 'expulsion with heat treated' with the properties of
their thermite welded rails. Compare the mechanical and
microstructural properties of thermite welded rails between
heat expulsion with heat treated and heat treated. Mechanical
and microstructural response expulsion with heat treated
thermite welded rail is higher value as compared to heat
treatment.
Abstract: Different approaches for heating\cooling of stirred tanks, coils and jackets, are investigated using computational fluid dynamics (CFD).A time-dependant sliding mesh approach is applied to simulate the flow in both conditions. The investigations are carried out under the turbulent flow conditions for a Rushton impeller and heating elements are considered isothermal. The flow behavior and temperature distribution are studied for each case and heat transfer coefficient is calculated. Results show different velocity profiles for each case. Unsteady temperature distribution is not similar for different cases .In the case of the coiled stirred vessel more uniform temperature and higher heat transfer coefficient is resulted.
Abstract: In order to Study the efficacy application of green
manure as chickpea pre plant, field experiments were carried out in
2007 and 2008 growing seasons. In this research the effects of
different strategies for soil fertilization were investigated on grain
yield and yield component, minerals, organic compounds and
cooking time of chickpea. Experimental units were arranged in splitsplit
plots based on randomized complete blocks with three
replications. Main plots consisted of (G1): establishing a mixed
vegetation of Vicia panunica and Hordeum vulgare and (G2):
control, as green manure levels. Also, five strategies for obtaining the
base fertilizer requirement including (N1): 20 t.ha-1 farmyard manure;
(N2): 10 t.ha-1 compost; (N3): 75 kg.ha-1 triple super phosphate;
(N4): 10 t.ha-1 farmyard manure + 5 t.ha-1 compost and (N5): 10 t.ha-1
farmyard manure + 5 t.ha-1 compost + 50 kg.ha-1 triple super
phosphate were considered in sub plots. Furthermoree four levels of
biofertilizers consisted of (B1): Bacillus lentus + Pseudomonas
putida; (B2): Trichoderma harzianum; (B3): Bacillus lentus +
Pseudomonas putida + Trichoderma harzianum; and (B4): control
(without biofertilizers) were arranged in sub-sub plots. Results
showed that integrating biofertilizers (B3) and green manure (G1)
produced the highest grain yield. The highest amounts of yield were
obtained in G1×N5 interaction. Comparison of all 2-way and 3-way
interactions showed that G1N5B3 was determined as the superior
treatment. Significant increasing of N, P2O5, K2O, Fe and Mg content
in leaves and grains emphasized on superiority of mentioned
treatment because each one of these nutrients has an approved role in
chlorophyll synthesis and photosynthesis abilities of the crops. The
combined application of compost, farmyard manure and chemical
phosphorus (N5) in addition to having the highest yield, had the best
grain quality due to high protein, starch and total sugar contents, low
crude fiber and reduced cooking time.