Abstract: In mechanical and environmental engineering, mixed
convection is a frequently encountered thermal fluid phenomenon
which exists in atmospheric environment, urban canopy flows, ocean
currents, gas turbines, heat exchangers, and computer chip cooling
systems etc... . This paper deals with a numerical investigation of
mixed convection in a vertical heated channel. This flow results from
the mixing of the up-going fluid along walls of the channel with the
one issued from a flat nozzle located in its entry section. The fluiddynamic
and heat-transfer characteristics of vented vertical channels
are investigated for constant heat-flux boundary conditions, a
Rayleigh number equal to 2.57 1010, for two jet Reynolds number
Re=3 103 and 2104 and the aspect ratio in the 8-20 range. The system
of governing equations is solved with a finite volumes method and an
implicit scheme. The obtained results show that the turbulence and
the jet-wall interaction activate the heat transfer, as does the drive of
ambient air by the jet. For low Reynolds number Re=3 103, the
increase of the aspect Ratio enhances the heat transfer of about 3%,
however; for Re=2 104, the heat transfer enhancement is of about
12%. The numerical velocity, pressure and temperature fields are
post-processed to compute the quantities of engineering interest such
as the induced mass flow rate, and average Nusselt number, in terms
of Rayleigh, Reynolds numbers and dimensionless geometric
parameters are presented.
Abstract: Starting from a biologically inspired framework, Gabor filters were built up from retinal filters via LMSE algorithms. Asubset of retinal filter kernels was chosen to form a particular Gabor filter by using a weighted sum. One-dimensional optimization approaches were shown to be inappropriate for the problem. All model parameters were fixed with biological or image processing constraints. Detailed analysis of the optimization procedure led to the introduction of a minimization constraint. Finally, quantization of weighting factors was investigated. This resulted in an optimized cascaded structure of a Gabor filter bank implementation with lower computational cost.
Abstract: Bond graph models of an electrical transformer
including the nonlinear saturation are presented. These models
determine the relation between self and mutual inductances, and
the leakage and magnetizing inductances of power transformers
with two and three windings using the properties of a bond
graph. The modelling and analysis using this methodology to
three phase power transformers or transformers with internal
incipient faults can be extended.
Abstract: The ability of information systems to operate in conjunction with each other encompassing communication protocols, hardware, software, application, and data compatibility layers. There has been considerable work in industry on the development of component interoperability models, such as CORBA, (D)COM and JavaBeans. These models are intended to reduce the complexity of software development and to facilitate reuse of off-the-shelf components. The focus of these models is syntactic interface specification, component packaging, inter-component communications, and bindings to a runtime environment. What these models lack is a consideration of architectural concerns – specifying systems of communicating components, explicitly representing loci of component interaction, and exploiting architectural styles that provide well-understood global design solutions. The development of complex business applications is now focused on an assembly of components available on a local area network or on the net. These components must be localized and identified in terms of available services and communication protocol before any request. The first part of the article introduces the base concepts of components and middleware while the following sections describe the different up-todate models of communication and interaction and the last section shows how different models can communicate among themselves.
Abstract: The purpose of this study is to investigate the effects
of modality principles in instructional software among first grade
pupils- achievements in the learning of Arabic Language. Two modes
of instructional software were systematically designed and
developed, audio with images (AI), and text with images (TI). The
quasi-experimental design was used in the study. The sample
consisted of 123 male and female pupils from IRBED Education
Directorate, Jordan. The pupils were randomly assigned to any one of
the two modes. The independent variable comprised the two modes
of the instructional software, the students- achievement levels in the
Arabic Language class and gender. The dependent variable was the
achievements of the pupils in the Arabic Language test. The
theoretical framework of this study was based on Mayer-s Cognitive
Theory of Multimedia Learning. Four hypotheses were postulated
and tested. Analyses of Variance (ANOVA) showed that pupils using
the (AI) mode performed significantly better than those using (TI)
mode. This study concluded that the audio with images mode was an
important aid to learning as compared to text with images mode.
Abstract: In this experimental investigation shake table tests
were conducted on two reduced models that represent normal single
room building constructed by Compressed Stabilized Earth Block
(CSEB) from locally available soil. One model was constructed with
earthquake resisting features (EQRF) having sill band, lintel band and
vertical bands to control the building vibration and another one was
without Earthquake Resisting Features. To examine the seismic
capacity of the models particularly when it is subjected to long-period
ground motion by large amplitude by many cycles of repeated
loading, the test specimen was shaken repeatedly until the failure.
The test results from Hi-end Data Acquisition system show that
model with EQRF behave better than without EQRF. This modified
masonry model with new material combined with new bands is used
to improve the behavior of masonry building.
Abstract: This paper gives an overview of the mapping
mechanism of SEAM-a methodology for the automatic generation of
knowledge models and its mapping onto Java codes. It discusses the
rules that will be used to map the different components in the
knowledge model automatically onto Java classes, properties and
methods. The aim of developing this mechanism is to help in the
creation of a prototype which will be used to validate the knowledge
model which has been generated automatically. It will also help to
link the modeling phase with the implementation phase as existing
knowledge engineering methodologies do not provide for proper
guidelines for the transition from the knowledge modeling phase to
development phase. This will decrease the development overheads
associated to the development of Knowledge Based Systems.
Abstract: One of the best ways for achievement of conventional
vehicle changing to hybrid case is trustworthy simulation result and
using of driving realities. For this object, in this paper, at first sevendegree-
of-freedom dynamical model of vehicle will be shown. Then
by using of statically model of engine, gear box, clutch, differential,
electrical machine and battery, the hybrid automobile modeling will
be down and forward simulation of vehicle for pedals to wheels
power transformation will be obtained. Then by design of a fuzzy
controller and using the proper rule base, fuel economy and
regenerative braking will be marked. Finally a series of
MATLAB/SIMULINK simulation results will be proved the
effectiveness of proposed structure.
Abstract: The bonding configuration and the heat of adsorption
of a furfural molecule on the Pd(111) surface were determined by ab
initio density-functional-theory calculations. The dynamics of pure
liquid water, the liquid-solid interface formed by liquid water and the
Pd(111) surface, as well as furfural at the water-Pd interface, were
investigated by ab initio molecular dynamics simulations at finite
temperatures. Calculations and simulations suggest that the bonding
configurations at the water-Pd interface promote decarbonylation of
furfural.
Abstract: Along with the advances in medicine, providing medical information to individual patient is becoming more important. In Japan such information via Braille is hardly provided to blind and partially sighted people. Thus we are researching and developing a Web-based automatic translation program “eBraille" to translate Japanese text into Japanese Braille. First we analyzed the Japanese transcription rules to implement them on our program. We then added medical words to the dictionary of the program to improve its translation accuracy for medical text. Finally we examined the efficacy of statistical learning models (SLMs) for further increase of word segmentation accuracy in braille translation. As a result, eBraille had the highest translation accuracy in the comparison with other translation programs, improved the accuracy for medical text and is utilized to make hospital brochures in braille for outpatients and inpatients.
Abstract: Previous studies have shown that there are arguments
regarding the reliability and validity of the Ashworth and Modified
Ashworth Scale towards evaluating patients diagnosed with upper
limb disorders. These evaluations depended on the raters’ experiences.
This initiated us to develop an upper limb disorder part-task trainer
that is able to simulate consistent upper limb disorders, such as
spasticity and rigidity signs, based on the Modified Ashworth Scale to
improve the variability occurring between raters and intra-raters
themselves. By providing consistent signs, novice therapists would be
able to increase training frequency and exposure towards various
levels of signs. A total of 22 physiotherapists and occupational
therapists participated in the study. The majority of the therapists
agreed that with current therapy education, they still face problems
with inter-raters and intra-raters variability (strongly agree 54%; n =
12/22, agree 27%; n = 6/22) in evaluating patients’ conditions. The
therapists strongly agreed (72%; n = 16/22) that therapy trainees
needed to increase their frequency of training; therefore believe that
our initiative to develop an upper limb disorder training tool will help
in improving the clinical education field (strongly agree and agree
63%; n = 14/22).
Abstract: This paper investigated the impact of ceiling height and window head heights variation on daylighting inside architectural teaching studio with a full width window. In architectural education, using the studio is more than normal classroom in most credit hours. Therefore, window position, size and dimension of studio have direct influence on level of daylighting. Daylighting design is a critical factor that improves student learning, concentration and behavior, in addition to these, it also reduces energy consumption. The methodology of analysis involves using Radiance in IES software under overcast and cloudy sky in Malaysia. It has been established that presentation of daylighting of architecture studio can be enhanced by changing the ceiling heights and window level, because, different ceiling heights and window head heights can contribute to different range of daylight levels.
Abstract: This research was to evaluate a technical feasibility of
making single-layer experimental particleboard panels from bamboo
waste (Dendrocalamus asper Backer) by converting bamboo into
strips, which are used to make laminated bamboo furniture. Variable
factors were density (600, 700 and 800 kg/m3) and temperature of
condition (25, 40 and 55 °C). The experimental panels were tested for
their physical and mechanical properties including modulus of
elasticity (MOE), modulus of rupture (MOR), internal bonding
strength (IB), screw holding strength (SH) and thickness swelling
values according to the procedures defined by Japanese Industrial
Standard (JIS). The test result of mechanical properties showed that
the MOR, MOE and IB values were not in the set criteria, except the
MOR values at the density of 700 kg/m3 at 25 °C and at the density
of 800 kg/m3 at 25 and 40 °C, the IB values at the density of 600
kg/m3, at 40 °C, and at the density of 800 kg/m3 at 55 °C. The SH
values had the test result according to the set standard, except with
the density of 600 kg/m3, at 40 and 55 °C. Conclusively, a valuable
renewable biomass, bamboo waste could be used to manufacture
boards.
Abstract: Steel plate shear walls (SPSWs) in buildings are
known to be an effective means for resisting lateral forces. By using
un-stiffened walls and allowing them to buckle, their energy
absorption capacity will increase significantly due to the postbuckling
capacity. The post-buckling tension field action of SPSWs
can provide substantial strength, stiffness and ductility. This paper
presents the Finite Element Analysis of low yield point (LYP) steel
shear walls. In this shear wall system, the LYP steel plate is used for
the steel panel and conventional structural steel is used for boundary
frames. A series of nonlinear cyclic analyses were carried out to
obtain the stiffness, strength, deformation capacity, and energy
dissipation capacity of the LYP steel shear wall. The effect of widthto-
thickness ratio of steel plate on buckling behavior, and energy
dissipation capacities were studied. Good energy dissipation and
deformation capacities were obtained for all models.
Abstract: In the artificial intelligence field, knowledge
representation and reasoning are important areas for intelligent
systems, especially knowledge base systems and expert systems.
Knowledge representation Methods has an important role in
designing the systems. There have been many models for knowledge
such as semantic networks, conceptual graphs, and neural networks.
These models are useful tools to design intelligent systems. However,
they are not suitable to represent knowledge in the domains of reality
applications. In this paper, new models for knowledge representation
called computational networks will be presented. They have been
used in designing some knowledge base systems in education for
solving problems such as the system that supports studying
knowledge and solving analytic geometry problems, the program for
studying and solving problems in Plane Geometry, the program for
solving problems about alternating current in physics.
Abstract: A minimal complexity version of component mode
synthesis is presented that requires simplified computer
programming, but still provides adequate accuracy for modeling
lower eigenproperties of large structures and their transient
responses. The novelty is that a structural separation into components
is done along a plane/surface that exhibits rigid-like behavior, thus
only normal modes of each component is sufficient to use, without
computing any constraint, attachment, or residual-attachment modes.
The approach requires only such input information as a few (lower)
natural frequencies and corresponding undamped normal modes of
each component. A novel technique is shown for formulation of
equations of motion, where a double transformation to generalized
coordinates is employed and formulation of nonproportional damping
matrix in generalized coordinates is shown.
Abstract: Due to the three- dimensional flow pattern interacting with bed material, the process of local scour around bridge piers is complex. Modeling 3D flow field and scour hole evolution around a bridge pier is more feasible nowadays because the computational cost and computational time have significantly decreased. In order to evaluate local flow and scouring around a bridge pier, a completely three-dimensional numerical model, SSIIM program, was used. The model solves 3-D Navier-Stokes equations and a bed load conservation equation. The model was applied to simulate local flow and scouring around a bridge pier in a large natural river with four piers. Computation for 1 day of flood condition was carried out to predict the maximum local scour depth. The results show that the SSIIM program can be used efficiently for simulating the scouring in natural rivers. The results also showed that among the various turbulence models, the k-ω model gives more reasonable results.
Abstract: This experiment was carried out to study the effect of
AMF, drought stress and phosphorus on physiological growth indices of basil at Iran using by a split-plot design with three replications.
The main-plot factor included: two levels of irrigation regimes (control=no drought stress and irrigation after 80 evaporation=
drought stress condition) while the sub-plot factors included
phosphorus (0, 35 and 70 kg/ha) and application and non-application of Glomus fasciculatum. The results showed that total dry matter
(TDM), life area index (LAI), relative growth rate (RGR) and crop growth rate (CGR) were all highly significantly different among the
phosphorus, whereas drought stress had effect of practical
significance on TDM, LAI, RGR and CGR. The results also showed that the highest TDM, LAI, RGR and CGR were obtained from
application of Glomus fasciculatum under no-drought condition.
Abstract: In modern agriculture, polymeric hydrogels are
known as a component able to hold an amount of water due to their
3-dimensional network structure and their tendency to absorb water
in humid environments. In addition, these hydrogels are able to
controllably release the fertilisers and pesticides loaded in them.
Therefore, they deliver these materials to the plants' roots and help
them with growing. These hydrogels also reduce the pollution of
underground water sources by preventing the active components
from leaching. In this study, sIPN acrylamide based hydrogels are
synthesised by using acrylamide free radical, potassium acrylate, and
linear polyvinyl alcohol. Ammonium nitrate is loaded in the hydrogel
as the fertiliser. The effect of various amounts of monomers and
linear polymer, measured in molar ratio, on the swelling rate,
equilibrium swelling, and release of ammonium nitrate is studied.
Abstract: This paper presents the solution of power economic dispatch (PED) problem of generating units with valve point effects and multiple fuel options using Self-Adaptive Differential Evolution (SDE) algorithm. The global optimal solution by mathematical approaches becomes difficult for the realistic PED problem in power systems. The Differential Evolution (DE) algorithm is found to be a powerful evolutionary algorithm for global optimization in many real problems. In this paper the key parameters of control in DE algorithm such as the crossover constant CR and weight applied to random differential F are self-adapted. The PED problem formulation takes into consideration of nonsmooth fuel cost function due to valve point effects and multi fuel options of generator. The proposed approach has been examined and tested with the numerical results of PED problems with thirteen-generation units including valve-point effects, ten-generation units with multiple fuel options neglecting valve-point effects and ten-generation units including valve-point effects and multiple fuel options. The test results are promising and show the effectiveness of proposed approach for solving PED problems.