Abstract: Space Vector Modulation (SVM) is an optimum Pulse Width Modulation (PWM) technique for an inverter used in a variable frequency drive applications. It is computationally rigorous and hence limits the inverter switching frequency. Increase in switching frequency can be achieved using Neural Network (NN) based SVM, implemented on application specific chips. This paper proposes a neural network based SVM technique for a Voltage Source Inverter (VSI). The network proposed is independent of switching frequency. Different architectures are investigated keeping the total number of neurons constant. The performance of the inverter is compared for various switching frequencies for different architectures of NN based SVM. From the results obtained, the network with minimum resource and appropriate word length is identified. The bit precision required for this application is identified. The network with 8-bit precision is implemented in the IC XCV 400 and the results are presented. The performance of NN based general purpose SVM with higher bit precision is discussed.
Abstract: The main objective of this paper is a comparative
investigate in enhancement of damping power system oscillation via
coordinated design of the power system stabilizer (PSS) and static
synchronous series compensator (SSSC) and static synchronous
compensator (STATCOM). The design problem of FACTS-based
stabilizers is formulated as a GA based optimization problem. In this
paper eigenvalue analysis method is used on small signal stability of
single machine infinite bus (SMIB) system installed with SSSC and
STATCOM. The generator is equipped with a PSS. The proposed
stabilizers are tested on a weakly connected power system with
different disturbances and loading conditions. This aim is to enhance
both rotor angle and power system stability. The eigenvalue analysis
and non-linear simulation results are presented to show the effects of
these FACTS-based stabilizers and reveal that SSSC exhibits the best
effectiveness on damping power system oscillation.
Abstract: This study assessed the effects of climate change on
Thai soybeans under simulation situations. Our study is focused on
temperature variability and effects on growth, yield, and genetic
changes in 2 generations of Chiang Mai 60 cultivars. In the
experiment, soybeans were exposed to 3 levels of air temperature for
8 h day-1 in an open top chamber for 2 cropping periods. Air
temperature levels in each treatment were controlled at 30-33°C (±
2.3) for LT-treatment, 33-36°C ( ± 2.4) for AT-treatment, and 36-40
°C ( ± 3.2) for HT-treatment, respectively. Positive effects of high
temperature became obvious at the maturing stage when yield
significantly increased in both cropping periods. Results in growth
indicated that shoot length at the pre-maturing stage
(V3-R3) was more positively affected by high temperature than at the
maturing stage. However, the positive effect on growth under high
temperature was not found in the 2nd cropping period. Finally, genetic
changes were examined in phenotype characteristics by the AFLPs
technique. The results showed that the high temperature factor clearly
caused genetic change in the soybeans and showed more alteration in
the 2nd cropping period.
Abstract: Construction site safety in China has aroused
comprehensive concern all over the world. It is imperative to
investigate the main causes of poor construction site safety. This paper
divides all the causes into four aspects, namely the factors of workers,
object, environment and management and sets up the accident causes
element system based on Delphi Method. This is followed by the
application of structural equation modeling to examine the importance
of each aspect of causes from the standpoints of different roles related
to the construction respectively. The results indicate that all the four
aspects of factors are in need of improvement, and different roles have
different ideas considering the priority of those factors. The paper has
instructive significance for the practitioners to take measures to
improve construction site safety in China accordingly.
Abstract: This paper describes the development of an
autonomous robot for painting the interior walls of buildings. The
robot consists of a painting arm with an end effector roller that scans
the walls vertically and a mobile platform to give horizontal feed to
paint the whole area of the wall. The painting arm has a planar twolink
mechanism with two joints. Joints are driven from a stepping
motor through a ball screw-nut mechanism. Four ultrasonic sensors
are attached to the mobile platform and used to maintain a certain
distance from the facing wall and to avoid collision with side walls.
When settled on adjusted distance from the wall, the controller starts
the painting process autonomously. Simplicity, relatively low weight
and short painting time were considered in our design. Different
modules constituting the robot have been separately tested then
integrated. Experiments have shown successfulness of the robot in its
intended tasks.
Abstract: Mobile Ad Hoc network is an infrastructure less
network which operates with the coordination of each node. Each node
believes to help another node, by forwarding its data to/from another
node. Unlike a wired network, nodes in an ad hoc network are resource
(i.e. battery, bandwidth computational capability and so on)
constrained. Such dependability of one node to another and limited
resources of nodes can result in non cooperation by any node to
accumulate its resources. Such non cooperation is known as selfish
behavior.
This paper discusses the performance analysis of very well known
MANET single-path (i.e. AODV) and multi-path (i.e. AOMDV)
routing protocol, in the presence of selfish behaviors. Along with
existing selfish behaviors, a new variation is also studied. Extensive
simulations were carried out using ns-2 and the study concluded that
the multi-path protocol (i.e. AOMDV) with link disjoint configuration
outperforms the other two configurations.
Abstract: ZnO-SnO2 i.e. Zinc-Tin-Oxide (ZTO) thin films were
deposited on glass substrate with varying concentrations (ZnO:SnO2
- 100:0, 90:10, 70:30 and 50:50 wt.%) at room temperature by flash
evaporation technique. These deposited ZTO film were annealed at
450 0C in vacuum. These films were characterized to study the effect
of annealing on the structural, electrical, and optical properties.
Atomic force microscopy (AFM) and Scanning electron microscopy
(SEM) images manifest the surface morphology of these ZTO thin
films. The apparent growth of surface features revealed the formation
of nanostructure ZTO thin films. The small value of surface
roughness (root mean square RRMS) ensures the usefulness in
optical coatings. The sheet resistance was also found to be decreased
for both types of films with increasing concentration of SnO2. The
optical transmittance found to be decreased however blue shift has
been observed after annealing.
Abstract: Two different superhydrophobic surfaces were
elaborated and their oil repellency behavior was evaluated using
several liquid with different surface tension. A silicone rubber/SiO2
nanocomposite coated (A) on aluminum substrate by “spin-coating"
and the sample B was an anodized aluminum surface covered by
Teflon-like coating. A high static contact angle about ∼162° was
measured for two prepared surfaces on which the water droplet rolloff.
Scanning electron microscopy (SEM) showed the presence of
micro/nanostructures for both sample A and B similar to that of lotus
leaf.
However the sample A presented significantly different behaviour
of wettability against the low surface tension liquid. Sample A has
been wetted totally by oil (dodecan) droplet while sample B showed
oleophobic behaviour. Oleophobic property of Teflon like coating
can be contributed to the presence of CF2 and CF3 functional group
which was shown by XPS analysis.
Abstract: Multi-level voltage source inverters offer several
advantages such as; derivation of a refined output voltage with
reduced total harmonic distortion (THD), reduction of voltage ratings
of the power semiconductor switching devices and also the reduced
electro-magnetic-interference problems etc. In this paper, new
carrier-overlapped phase-disposition or sub-harmonic sinusoidal
pulse width modulation (CO-PD-SPWM) and also the carrieroverlapped
phase-disposition space vector modulation (CO-PDSVPWM)
schemes for a six-level diode-clamped inverter topology
are proposed. The principle of the proposed PWM schemes is similar
to the conventional PD-PWM with a little deviation from it in the
sense that the triangular carriers are all overlapped. The overlapping
of the triangular carriers on one hand results in an increased number
of switchings, on the other hand this facilitates an improved spectral
performance of the output voltage. It is demonstrated through
simulation studies that the six-level diode-clamped inverter with the
use of CO-PD-SPWM and CO-PD-SVPWM proposed in this paper is
capable of generating multiple levels in its output voltage. The
advantages of the proposed PWM schemes can be derived to benefit,
especially at lower modulation indices of the inverter and hence this
aspect of the proposed PWM schemes can be well exploited in high
power applications requiring low speeds of operation of the drive.
Abstract: The development of One Tambon One Product
(OTOP) became the policy of the government in 1997 after the
former Prime Minister had been in power. The strategy of sections is
currently set for the policy. OTOP has become the part of the way of
community lives around the country. OTOP may be developed under
changing into ASEAN economic community in 2015 because of the
flow of capitals, productions, and many workers in the region. All
sectors are improved for the change. The purposes of study were to
study the strength and weakness of the OTOP-creating process via its
policy and to lead to the strategy to be able to apply before changing.
The methodology is qualitative to study its policy including
document and to interview experienced persons. The findings showed
that the effort of improvement of all sectors obviously involves with
OTOP development. Particularly, the strategic administration of
OTOP is in every level of the state, central sector, region, and
community.
Abstract: Human immunodeficiency virus infection and
acquired immunodeficiency syndrome is a global pandemic with
cases reporting from virtually every country and continues to be a
common infection in developing country like India.
Microalbuminuria is a manifestation of human immunodeficiency
virus associated nephropathy. Therefore, microalbuminuria may be
an early marker of human immunodeficiency virus associated
nephropathy, and screening for its presence may be beneficial. A
strikingly high prevalence of microalbuminuria among human
immunodeficiency virus infected patients has been described in
various studies. Risk factors for clinically significant proteinuria
include African - American race, higher human immunodeficiency
virus ribonucleic acid level and lower CD4 lymphocyte count. The
cardiovascular risk factors of increased systolic blood pressure and
increase fasting blood sugar level are strongly associated with
microalbuminuria in human immunodeficiency virus patient. These
results suggest that microalbuminuria may be a sign of current
endothelial dysfunction and micro-vascular disease and there is
substantial risk of future cardiovascular disease events. Positive
contributing factors include early kidney disease such as human
immunodeficiency virus associated nephropathy, a marker of end
organ damage related to co morbidities of diabetes or hypertension,
or more diffuse endothelial cells dysfunction. Nevertheless after
adjustment for non human immunodeficiency virus factors, human
immunodeficiency virus itself is a major risk factor. The presence of
human immunodeficiency virus infection is independent risk to
develop microalbuminuria in human immunodeficiency virus patient.
Cardiovascular risk factors appeared to be stronger predictors of
microalbuminuria than markers of human immunodeficiency virus
severity person with human immunodeficiency virus infection and
microalbuminuria therefore appear to potentially bear the burden of
two separate damage related to known vascular end organ damage
related to know vascular risk factors, and human immunodeficiency
virus specific processes such as the direct viral infection of kidney
cells.The higher prevalence of microalbuminuria among the human
immunodeficiency virus infected could be harbinger of future
increased risks of both kidney and cardiovascular disease. Further
study defining the prognostic significance of microalbuminuria
among human immunodeficiency virus infected persons will be
essential. Microalbuminuria seems to be a predictor of cardiovascular
disease in diabetic and non diabetic subjects, hence it can also be
used for early detection of micro vascular disease in human
immunodeficiency virus positive patients, thus can help to diagnose
the disease at the earliest.
Abstract: The Influence Diagrams (IDs) is a kind of Probabilistic Belief Networks for graphic modeling. The usage of IDs can improve the communication among field experts, modelers, and decision makers, by showing the issue frame discussed from a high-level point of view. This paper enhances the Time-Sliced Influence Diagrams (TSIDs, or called Dynamic IDs) based formalism from a Discrete Event Systems Modeling and Simulation (DES M&S) perspective, for Exploring Analysis (EA) modeling. The enhancements enable a modeler to specify times occurred of endogenous events dynamically with stochastic sampling as model running and to describe the inter- influences among them with variable nodes in a dynamic situation that the existing TSIDs fails to capture. The new class of model is named Dynamic-Stochastic Influence Diagrams (DSIDs). The paper includes a description of the modeling formalism and the hiberarchy simulators implementing its simulation algorithm, and shows a case study to illustrate its enhancements.
Abstract: Some of the students' problems in writing skill stem
from inadequate preparation for the writing assignment. Students
should be taught how to write well when they arrive in language
classes. Having selected a topic, the students examine and explore the
theme from as large a variety of viewpoints as their background and
imagination make possible. Another strategy is that the students
prepare an Outline before writing the paper. The comparison between
the two mentioned thought provoking techniques was carried out
between the two class groups –students of Islamic Azad University of
Dezful who were studying “Writing 2" as their main course. Each
class group was assigned to write five compositions separately in
different periods of time. Then a t-test for each pair of exams between
the two class groups showed that the t-observed in each pair was
more than the t-critical. Consequently, the first hypothesis which
states those who utilize Brainstorming as a thought provoking
technique in prewriting phase are more successful than those who
outline the papers before writing was verified.
Abstract: This paper demonstrates how the soft systems
methodology can be used to improve the delivery of a module in data warehousing for fourth year information technology students.
Graduates in information technology needs to have academic skills
but also needs to have good practical skills to meet the skills requirements of the information technology industry. In developing
and improving current data warehousing education modules one has to find a balance in meeting the expectations of various role players such as the students themselves, industry and academia. The soft
systems methodology, developed by Peter Checkland, provides a
methodology for facilitating problem understanding from different world views. In this paper it is demonstrated how the soft systems methodology can be used to plan the improvement of data
warehousing education for fourth year information technology students.
Abstract: The Information and Communication Technologies
(ICTs), and the Wide World Web (WWW) have fundamentally
altered the practice of teaching and learning world wide. Many
universities, organizations, colleges and schools are trying to apply
the benefits of the emerging ICT. In the early nineties the term
learning object was introduced into the instructional technology
vernacular; the idea being that educational resources could be broken
into modular components for later combination by instructors,
learners, and eventually computes into larger structures that would
support learning [1]. However in many developing countries, the use
of ICT is still in its infancy stage and the concept of learning object
is quite new. This paper outlines the learning object design
considerations for developing countries depending on learning
environment.
Abstract: 53 college students answered questions regarding the circumstances in which they first heard about the news of Wenchuan earthquake or the news of their acceptance to college which took place approximately one year ago, and answered again two years later. The number of details recalled about their circumstances for both events was high and didn-t decline two years later. However, consistency in reported details over two years was low. Participants were more likely to construct central (e.g., Where were you?) than peripheral information (What were you wearing?), and the confidence of the central information was higher than peripheral information, which indicated that they constructed more when they were more confident.
Abstract: When acid is pumped into damaged reservoirs for
damage removal/stimulation, distorted inflow of acid into the
formation occurs caused by acid preferentially traveling into highly
permeable regions over low permeable regions, or (in general) into
the path of least resistance. This can lead to poor zonal coverage and
hence warrants diversion to carry out an effective placement of acid.
Diversion is desirably a reversible technique of temporarily reducing
the permeability of high perm zones, thereby forcing the acid into
lower perm zones.
The uniqueness of each reservoir can pose several challenges to
engineers attempting to devise optimum and effective diversion
strategies. Diversion techniques include mechanical placement and/or
chemical diversion of treatment fluids, further sub-classified into ball
sealers, bridge plugs, packers, particulate diverters, viscous gels,
crosslinked gels, relative permeability modifiers (RPMs), foams,
and/or the use of placement techniques, such as coiled tubing (CT)
and the maximum pressure difference and injection rate (MAPDIR)
methodology.
It is not always realized that the effectiveness of diverters greatly
depends on reservoir properties, such as formation type, temperature,
reservoir permeability, heterogeneity, and physical well
characteristics (e.g., completion type, well deviation, length of
treatment interval, multiple intervals, etc.). This paper reviews the
mechanisms by which each variety of diverter functions and
discusses the effect of various reservoir properties on the efficiency
of diversion techniques. Guidelines are recommended to help
enhance productivity from zones of interest by choosing the best
methods of diversion while pumping an optimized amount of
treatment fluid. The success of an overall acid treatment often
depends on the effectiveness of the diverting agents.
Abstract: To understand complex living system an effort has
made by mechanical engineers and dentists to deliver prompt
products and services to patients concerned about their aesthetic look.
Since two decades various bracket systems have designed involving
techniques like milling, injection molding which are technically not
flexible for the customized dental product development. The aim of
this paper to design, develop a customized system which is
economical and mainly emphasizes the expertise design and
integration of engineering and dental fields. A custom made selfadjustable
lingual bracket and customized implants are designed and
developed using computer aided design (CAD) and rapid prototyping
technology (RPT) to improve the smiles and to overcome the
difficulties associated with conventional ones. Lengthy orthodontic
treatment usually not accepted by the patients because the patient
compliance is lost. Patient-s compliance can be improved by
facilitating faster tooth movements by designing a localized dental
vibrator using advanced engineering principles.
Abstract: With the globalized production and logistics
environment, the need for reducing the product development interval
and lead time, having a faster response to orders, conforming to quality
standards, fair tracking, and boosting information exchanging
activities with customers and partners, and coping with changes in the
management environment, manufacturers are in dire need of an
information management system in their manufacturing environments.
There are lots of information systems that have been designed to
manage the condition or operation of equipment in the field but
existing systems have a decentralized architecture, which is not
unified. Also, these systems cannot effectively handle the status data
extraction process upon encountering a problem related to protocols or
changes in the equipment or the setting. In this regard, this paper will
introduce a system for processing and saving the status info of
production equipment, which uses standard representation formats, to
enable flexible responses to and support for variables in the field
equipment. This system can be used for a variety of manufacturing and
equipment settings and is capable of interacting with higher-tier
systems such as MES.
Abstract: Three sulphonic acid-doped polyanilines were
synthesized through chemical oxidation at low temperature (0-5 oC)
and potential of these polymers as sensing agent for O2 gas detection
in terms of fluorescence quenching was studied. Sulphuric acid,
dodecylbenzene sulphonic acid (DBSA) and camphor sulphonic acid
(CSA) were used as doping agents. All polymers obtained were dark
green powder. Polymers obtained were characterized by Fourier
transform infrared spectroscopy, ultraviolet-visible absorption
spectroscopy, thermogravimetry analysis, elemental analysis,
differential scanning calorimeter and gel permeation
chromatography. Characterizations carried out showed that polymers
were successfully synthesized with mass recovery for sulphuric aciddoped
polyaniline (SPAN), DBSA-doped polyaniline (DBSA-doped
PANI) and CSA-doped polyaniline (CSA-doped PANI) of 71.40%,
75.00% and 39.96%, respectively. Doping level of SPAN, DBSAdoped
PANI and CSA-doped PANI were 32.86%, 33.13% and
53.96%, respectively as determined based on elemental analysis.
Sensing test was carried out on polymer sample in the form of
solution and film by using fluorescence spectrophotometer. Samples
of polymer solution and polymer film showed positive response
towards O2 exposure. All polymer solutions and films were fully
regenerated by using N2 gas within 1 hour period. Photostability
study showed that all samples of polymer solutions and films were
stable towards light when continuously exposed to xenon lamp for 9
hours. The relative standard deviation (RSD) values for SPAN
solution, DBSA-doped PANI solution and CSA-doped PANI
solution for repeatability were 0.23%, 0.64% and 0.76%,
respectively. Meanwhile RSD values for reproducibility were 2.36%,
6.98% and 1.27%, respectively. Results for SPAN film, DBSAdoped
PANI film and CSA-doped PANI film showed the same
pattern with RSD values for repeatability of 0.52%, 4.05% and
0.90%, respectively. Meanwhile RSD values for reproducibility were
2.91%, 10.05% and 7.42%, respectively. The study on effect of the
flow rate on response time was carried out using 3 different rates
which were 0.25 mL/s, 1.00 mL/s and 2.00 mL/s. Results obtained
showed that the higher the flow rate, the shorter the response time.