Abstract: In this paper a polymer electrolyte membrane (PEM)
fuel cell power system including burner, steam reformer, heat
exchanger and water heater has been considered to meet the
electrical, heating, cooling and domestic hot water loads of
residential building which in Tehran. The system uses natural gas as
fuel and works in CHP mode. Design and operating conditions of a
PEM fuel cell system is considered in this study. The energy
requirements of residential building and the number of fuel cell
stacks to meet them have been estimated. The method involved
exergy analysis and entropy generation thorough the months of the
year. Results show that all the energy needs of the building can be
met with 12 fuel cell stacks at a nominal capacity of 8.5 kW. Exergy
analysis of the CHP system shows that the increase in the ambient air
temperature from 1oC to 40oC, will have an increase of entropy
generation by 5.73%.Maximum entropy generates for 15 hour in 15th
of June and 15th of July is estimated to amount at 12624 (kW/K).
Entropy generation of this system through a year is estimated to
amount to 1004.54 GJ/k.year.
Abstract: The purpose of this study was to examine and
compare physical fitness values of students engaged in different team
sport branches Totally 60 female, and 60 male athletes, that 20
athletes in each branch which are volleyball, basketball and football
participated the study as a volunteer. The mean ages of female and
male athletes were 21.20 ±1.87 and 21.61 ± 1.61 respectively. Age,
height, body weight, body mass index, flexibility, body fat
percentage, 30m sprint, maximum oxygen consumption capacity
(MaxVO2) and drop jump values were measured. As a result of
measurements, significant differences were found in height, weight,
MaxVO2, shuttle run speed between different sports branches in
female athletes. In male athletes, height, body weight, flexibility,
30m split speed and drop jump values were found significantly
different between sports branches.
As a conclusion and as a literature, it can be said that structure of
body has to be appropriate with the engaged sports branch. Physical
fitness values that required the sports branches can be expressed
clearly by increasing the number of subjects.
Abstract: Because of importance of energy, optimization of
power generation systems is necessary. Gas turbine cycles are
suitable manner for fast power generation, but their efficiency is
partly low. In order to achieving higher efficiencies, some
propositions are preferred such as recovery of heat from exhaust
gases in a regenerator, utilization of intercooler in a multistage
compressor, steam injection to combustion chamber and etc.
However thermodynamic optimization of gas turbine cycle, even
with above components, is necessary. In this article multi-objective
genetic algorithms are employed for Pareto approach optimization of
Regenerative-Intercooling-Gas Turbine (RIGT) cycle. In the multiobjective
optimization a number of conflicting objective functions
are to be optimized simultaneously. The important objective
functions that have been considered for optimization are entropy
generation of RIGT cycle (Ns) derives using Exergy Analysis and
Gouy-Stodola theorem, thermal efficiency and the net output power
of RIGT Cycle. These objectives are usually conflicting with each
other. The design variables consist of thermodynamic parameters
such as compressor pressure ratio (Rp), excess air in combustion
(EA), turbine inlet temperature (TIT) and inlet air temperature (T0).
At the first stage single objective optimization has been investigated
and the method of Non-dominated Sorting Genetic Algorithm
(NSGA-II) has been used for multi-objective optimization.
Optimization procedures are performed for two and three objective
functions and the results are compared for RIGT Cycle. In order to
investigate the optimal thermodynamic behavior of two objectives,
different set, each including two objectives of output parameters, are
considered individually. For each set Pareto front are depicted. The
sets of selected decision variables based on this Pareto front, will
cause the best possible combination of corresponding objective
functions. There is no superiority for the points on the Pareto front
figure, but they are superior to any other point. In the case of three
objective optimization the results are given in tables.
Abstract: This study explores how the mechanics of learning
paves the way to engineering innovation. Theories related to learning
in the new product/service innovation are reviewed from an
organizational perspective, behavioral perspective, and engineering
perspective. From this, an engineering team-s external interactions
for knowledge brokering and internal composition for skill balance
are examined from a learning and innovation viewpoints. As a result,
an integrated learning model is developed by reconciling the
theoretical perspectives as well as developing propositions that
emphasize the centrality of learning, and its drivers, in the
engineering product/service development. The paper also provides a
review and partial validation of the propositions using the results of a
previously published field study in the aerospace industry.
Abstract: In recent years linguistic research has turned
increasing attention to covert/overt strategies to modulate authorial
stance and positioning in scientific texts, and to the recipients'
response. This study discussed some theoretical implications of the
use of rhetoric in scientific communication and analysed qualitative
data from the authoritative The Cognitive Neurosciences III (2004)
volume. Its genre-identity, status and readability were considered, in
the social interactive context of contemporary disciplinary discourses
– in their polyphony of traditional and new, emerging genres.
Evidence was given of the ways its famous authors negotiate and
shape knowledge and research results – explicitly appraising team
work and promoting faith in the fast-paced progress of Cognitive
Neuroscience, also through experiential metaphors – by presenting a
set of examples, ordered according to their dominant rhetorical
quality.
Abstract: With high speed vessels getting ever more sophisti-cated, travelling at higher and higher speeds and operating in With high speed vessels getting ever more sophisticated,
travelling at higher and higher speeds and operating in areas of
high maritime traffic density, training becomes of the highest priority
to ensure that safety levels are maintained, and risks are adequately
mitigated. Training onboard the actual craft on the actual route still
remains the most effective way for crews to gain experience. However,
operational experience and incidents during the last 10 years
demonstrate the need for supplementary training whether in the area
of simulation or man to man, man/ machine interaction. Training and
familiarisation of the crew is the most important aspect in preventing
incidents. The use of simulator, computer and web based training
systems in conjunction with onboard training focusing on critical
situations will improve the man machine interaction and thereby
reduce the risk of accidents. Today, both ship simulator and bridge
teamwork courses are now becoming the norm in order to improve
further emergency response and crisis management skills. One of the
main causes of accidents is the human factor. An efficient way to
reduce human errors is to provide high-quality training to the personnel
and to select the navigators carefully.areas of high maritime traffic density, training becomes of the highest priority to ensure that safety levels are maintained, and risks are adequately mitigated. Training onboard the actual craft on the actual route still remains the most effective way for crews to gain experience. How-ever, operational experience and incidents during the last 10 years demonstrate the need for supplementary training whether in the area of simulation or man to man, man/ machine interaction. Training and familiarisation of the crew is the most important aspect in preventing incidents. The use of simulator, computer and web based training systems in conjunction with onboard training focusing on critical situations will improve the man machine interaction and thereby reduce the risk of accidents. Today, both ship simulator and bridge teamwork courses are now becoming the norm in order to improve further emergency response and crisis management skills. One of the main causes of accidents is the human factor. An efficient way to reduce human errors is to provide high-quality training to the person-nel and to select the navigators carefully. KeywordsCBT - WBT systems, Human factors.
Abstract: The analytical prediction of the decay heat results
from the fast neutron fission of actinides was initiated under a project, 10-MAT1134-3, funded by king Abdulaziz City of Science
and Technology (KASCT), Long-Term Comprehensive National Plan for Science, Technology and Innovations, managed by a team
from King Abdulaziz University (KAU), Saudi Arabia, and
supervised by Argonne National Laboratory (ANL) has collaborated
with KAU's team to assist in the computational analysis. In this paper, the numerical solution of coupled linear differential equations
that describe the decays and buildups of minor fission product MFA, has been used to predict the total decay heat and its components from the fast neutron fission of 235U and 239Pu. The reliability of the present approach is illustrated via systematic
comparisons with the measurements reported by the University of
Tokyo, in YAYOI reactor.
Abstract: The objective of this research is to develop the
performance indicators (PIs) in operational level for the Pre-hospital Emergency Medical Service (EMS) system employing in Thailand. This research started with ascertaining the current pre-hospital care
system. The team analyzed the strategies of Narerthorn, a government unit under the ministry of public health, and the existing PIs of the pre-hospital care. Afterwards, the current National Strategic Plan of EMS development (2008-2012) of the Emergency
Medical Institute of Thailand (EMIT) was considered using strategic
analysis to developed Strategy Map (SM) and identified the Success
Factors (SFs). The analysis results from strategy map and SFs were used to develop the Performance Indicators (PIs). To verify the set of
PIs, the team has interviewed with the relevant practitioners for the possibilities to implement the PIs. To this paper, it was to ascertain
that all the developed PIs support the objectives of the strategic plan. Nevertheless, the results showed that the operational level PIs suited
only with the first dimension of National Strategic Plan
(infrastructure and information technology development). Besides,
the SF was the infrastructure development (to contribute the EMS system to people throughout with standard and efficiency both in normally and disaster conditions). Finally, twenty-nine indicators
were developed from the analysis results of SM and SFs.
Abstract: The Combination of path planning and path following is the main purpose of this paper. This paper describes the developed practical approach to motion control of the MRL small size robots. An intelligent controller is applied to control omni-directional robots motion in simulation and real environment respectively. The Brain Emotional Learning Based Intelligent Controller (BELBIC), based on LQR control is adopted for the omni-directional robots. The contribution of BELBIC in improving the control system performance is shown as application of the emotional learning in a real world problem. Optimizing of the control effort can be achieved in this method too. Next the implicit communication method is used to determine the high level strategies and coordination of the robots. Some simple rules besides using the environment as a memory to improve the coordination between agents make the robots' decision making system. With this simple algorithm our team manifests a desirable cooperation.
Abstract: Many agricultural and especially greenhouse
applications like plant inspection, data gathering, spraying and
selective harvesting could be performed by robots. In this paper
multiple nonholonomic robots are used in order to create a desired
formation scheme for screening solar energy in a greenhouse through
data gathering. The formation consists from a leader and a team
member equipped with appropriate sensors. Each robot is dedicated
to its mission in the greenhouse that is predefined by the
requirements of the application. The feasibility of the proposed
application includes experimental results with three unmanned
ground vehicles (UGV).
Abstract: Effective evaluation of software development effort is an important aspect of successful project management. Based on a large database with 4106 projects ever developed, this study statistically examines the factors that influence development effort. The factors found to be significant for effort are project size, average number of developers that worked on the project, type of development, development language, development platform, and the use of rapid application development. Among these factors, project size is the most critical cost driver. Unsurprisingly, this study found that the use of CASE tools does not necessarily reduce development effort, which adds support to the claim that the use of tools is subtle. As many of the current estimation models are rarely or unsuccessfully used, this study proposes a parsimonious parametric model for the prediction of effort which is both simple and more accurate than previous models.
Abstract: This paper is described one of the intelligent control method in Autonomous systems, which is called fuzzy control to correct the three wheel omnidirectional robot movement while it make mistake to catch the target. Fuzzy logic is especially advantageous for problems that can not be easily represented by mathematical modeling because data is either unavailable, incomplete or the process is too complex. Such systems can be easily up grated by adding new rules to improve performance or add new features. In many cases , fuzzy control can be used to improve existing traditional controller systems by adding an extra layer of intelligence to the current control method. The fuzzy controller designed here is more accurate and flexible than the traditional controllers. The project is done at MRL middle size soccer robot team.
Abstract: This work aims to test the application of computational fluid dynamics (CFD) modeling to fixed bed catalytic cracking reactors. Studies of CFD with a fixed bed design commonly use a regular packing with N=2 to define bed geometry. CFD allows us to obtain a more accurate view of the fluid flow and heat transfer mechanisms present in fixed bed equipment. Naphtha was used as feedstock and the reactor length was 80cm. It is divided in three sections that catalyst bed packed in the middle section of the reactor. The reaction scheme was involved one primary reaction and 24 secondary reactions. Because of high CPU times in these simulations, parallel processing have been used. In this study the coke formation process in fixed bed and empty tube reactor was simulated and coke in these reactors are compared. In addition, the effect of steam ratio and feed flow rate on coke formation was investigated.
Abstract: This presentation reviews recent advances in superalloys and thermal barrier coating (TBC) for application in hot sections of energy-efficient gas-turbine engines. It has been reviewed that in the modern combined-cycle gas turbines (CCGT) applying single-crystal energy materials (SC superalloys) and thermal barrier coatings (TBC), and – in one design – closed-loop steam cooling, thermal efficiency can reach more than 60%. These technological advancements contribute to profitable and clean power generation with reduced emission. Alternatively, the use of advanced superalloys (e.g. GTD-111 superalloy, Allvac 718Plus superalloy) and advanced thermal barrier coatings (TBC) in modern gas-turbines has been shown to yield higher energy-efficiency in power generation.
Abstract: A rigorous two-dimensional model is developed for simulating the operation of a less-investigated type steam reformer having a considerably lower operating Reynolds number, higher tube diameter, and non-availability of extra steam in the feed compared with conventional steam reformers. Simulation results show that reasonable predictions can only be achieved when certain correlations for wall to fluid heat transfer equations are applied. Due to severe operating conditions, in all cases, strong radial temperature gradients inside the reformer tubes have been found. Furthermore, the results show how a certain catalyst loading profile will affect the operation of the reformer.
Abstract: Fractional-order controller was proven to perform better than the integer-order controller. However, the absence of a pole at origin produced marginal error in fractional-order control system. This study demonstrated the enhancement of the fractionalorder PI over the integer-order PI in a steam temperature control. The fractional-order controller was cascaded with an error compensator comprised of a very small zero and a pole at origin to produce a zero steady-state error for the closed-loop system. Some modification on the error compensator was suggested for different order fractional integrator that can improve the overall phase margin.
Abstract: Existing experiences indicate that one of the most
prominent reasons that some ERP implementations fail is related to
selecting an improper ERP package. Among those important factors
resulting in inappropriate ERP selections, one is to ignore preliminary
activities that should be done before the evaluation of ERP packages.
Another factor yielding these unsuitable selections is that usually
organizations employ prolonged and costly selection processes in
such extent that sometimes the process would never be finalized
or sometimes the evaluation team might perform many key final
activities in an incomplete or inaccurate way due to exhaustion, lack
of interest or out-of-date data. In this paper, a systematic approach
that recommends some activities to be done before and after the
main selection phase is introduced for choosing an ERP package. On
the other hand, the proposed approach has utilized some ideas that
accelerates the selection process at the same time that reduces the
probability of an erroneous final selection.
Abstract: The world's population continues to grow at a quarter of a million people per day, increasing the consumption of energy. This has made the world to face the problem of energy crisis now days. In response to the energy crisis, the principles of renewable energy gained popularity. There are much advancement made in developing the wind and solar energy farms across the world. These energy farms are not enough to meet the energy requirement of world. This has attracted investors to procure new sources of energy to be substituted. Among these sources, extraction of energy from the waves is considered as best option. The world oceans contain enough energy to meet the requirement of world. Significant advancements in design and technology are being made to make waves as a continuous source of energy. One major hurdle in launching wave energy devices in a developing country like Pakistan is the initial cost. A simple, reliable and cost effective wave energy converter (WEC) is required to meet the nation-s energy need. This paper will present a novel design proposed by team SAS for harnessing wave energy. This paper has three major sections. The first section will give a brief and concise view of ocean wave creation, propagation and the energy carried by them. The second section will explain the designing of SAS-2. A gear chain mechanism is used for transferring the energy from the buoy to a rotary generator. The third section will explain the manufacturing of scaled down model for SAS-2 .Many modifications are made in the trouble shooting stage. The design of SAS-2 is simple and very less maintenance is required. SAS-2 is producing electricity at Clifton. The initial cost of SAS-2 is very low. This has proved SAS- 2 as one of the cost effective and reliable source of harnessing wave energy for developing countries.
Abstract: This paper describes the two actual tendencies in the
software development process usage: 'Scrum' and 'work in home
office'. It-s exposed the four main challenges to adopt Scrum
framework for distributed teams in this cited kind of work. The
challenges are mainly based on the communication problems due
distances since the Scrum encourages the team to work together in
the same room, and this is not possible when people work distributed
in their homes.
Abstract: Synthesis gas manufacturing by steam reforming of hydrocarbons is an important industrial process. High endothermic nature of the process makes it one of the most cost and heat intensive processes. In the present work, composite effect of different inert gases on synthesis gas yield, feed gas conversion and temperature distribution along the reactor length has been studied using a heterogeneous model. Mathematical model was developed as a first stage and validated against the existing process models. With the addition of inert gases, a higher yield of synthesis gas is observed. Simultaneously the rector outlet temperature drops to as low as 810 K. It was found that Xenon gives the highest yield and conversion while Helium gives the lowest temperature. Using Xenon inert gas 20 percent reduction in outlet temperature was observed compared to traditional case.