Abstract: Software engineering education not only embraces
technical skills of software development but also necessitates
communication and interaction among learners. In this paper, it is
proposed to adapt the PBL methodology that is especially designed to
be integrated into software engineering classroom in order to promote
collaborative learning environment. This approach helps students
better understand the significance of social aspects and provides a
systematic framework to enhance teamwork skills. The adaptation of
PBL facilitates the transition to an innovative software development
environment where cooperative learning can be actualized.
Abstract: The increasing recognition of the need for education to be closely aligned with team playing, project based learning and problem solving approaches has increase the interest in collaborative learning among university and college instructors. Using online collaboration learning in learning can enhance the outcome and achievement of students as well as improve their communication, critical thinking and personnel skills. The current research aims at examining the effect of OCL on the student's achievement at Kingdom of Bahrain. Numbers of objectives were set to achieve the aim of the research include: investigating the current situation regarding the collaborative learning and OCL at the Kingdom of Bahrain by identifying the advantages and effectiveness of OCL as a learning tool over traditional learning, examining the factors that affect OCL as well as examining the impact of OCL on the student's achievement. To achieve these objectives, quantitative method was adopted. Two hundred and thirty one questionnaires were distributed to students in different local and private universities at Kingdom of Bahrain. The findings of the research show that most of the students prefer to use FTFCL in learning and that OCL is already adopted in some universities especially in University of Bahrain. Moreover, the most factors affecting the adopted OCL are perceived readiness, and guidance and support.
Abstract: An important goal of parboiling is a decrease of rice broken percentage and at the beginning Selected paddy of variety of rice Tarom and soaked at three different temperatures 45 Cº, 65 Cº and 80 Cº orderly for 5 hours, 4 hours and 1.5 hours to moisture of 40 % and then in steaming stage to operate these action two steaming methods are selected steaming under pressure condition and steaming in atmosphere pressure and In the first method after exerting air, the steam pressure is increase to 1 Kg/Cm2 which is done in two different duration times of 2.5 and 5 minutes and in second method used of three times of 5,10 and 15 minutes and dry to 8% moisture and decreases of rice broken percentage at best condition in variety of Tarom of 37.2 % to 7.3 % and increases yield percentage at best condition in variety of Tarom of 69.4 % to 75.93 % and bran percentage decreased in variety of Tarom of 9.53 % to 2.2-3.2 % and this issue cause increases yield percentage in rice and use of This method is very significant for our country because broken percentage of rice in our country is 23-33 %.
Abstract: Nosocomial (i.e., hospital-acquired) infections
(NI) is a major cause of morbidity and mortality in hospitals. NI
rate is higher in intensive care units (ICU) than in the general
ward due to patients with severe symptoms, poor immunity,
and accepted many invasive therapies. Contact behaviors
between health caregivers and patients is one of the infect
factors. It is difficult to obtain complete contact records by
traditional method of retrospective analysis of medical records.
This paper establishes a contact history inferential model
(CHIM) intended to extend the use of Proximity Sensing of
rapid frequency identification (RFID) technology to
transferring all proximity events between health caregivers and
patients into clinical events (close-in events, contact events and
invasive events).The results of the study indicated that the
CHIM can infer proximity care activities into close-in events
and contact events.
The infection control team could redesign and build optimal
workflow in the ICU according to the patient-specific contact
history which provided by our automatic tracing system.
Abstract: Although automotive industry has brought different beneficiaries to human life, it is being pointed out as one of the major cause of global air pollution which resulted in climate change, smog, green house gases (GHGs), and human diseases by many reasons. Since auto industry is one of the largest consumers of fossil fuels, the realization of green innovations is becoming a crucial choice to meet the challenges towards sustainable development. Recently, many auto manufacturers have embarked on green technology initiatives to gain a competitive advantage in the global market; however, innovative manufacturing systems and technologies can enhance operational performance only if the human resource management is in place to elicit the motivation of the employees and develop their organizational expertise. No organization can perform at peak levels unless each employee is committed to the company goals and works as an effective team member. Strategic human resource practices are the primary means by which firms can shape the skills, attitudes, and behavior of individuals to align with the business strategic objectives. This study investigates on the comprehensive approach of multiple advanced technology innovations and human resource management at Toyota Motor Corporation as the market leader of full hybrid technology in the automotive industry. Then, HRM framework of the company is described and three sets of human resource practices that support the innovation-oriented HR system, presented. Finally, a conceptual framework for innovativeness in green technology in automotive industry by applying a deliberate strategic HR management system and knowledge management with the intervening factors of organizational culture, knowledge application and knowledge sharing is proposed.
Abstract: Two-interconnected fluidized bed systems are widely used in various processes such as Fisher-Tropsch, hot gas desulfurization, CO2 capture-regeneration with dry sorbent, chemical-looping combustion, sorption enhanced steam methane reforming, chemical-looping hydrogen generation system, and so on. However, most of two-interconnected fluidized beds systems require riser and/or pneumatic transport line for solid conveying and loopseals or seal-pots for gas sealing, recirculation of solids to the riser, and maintaining of pressure balance. The riser (transport bed) is operated at the high velocity fluidization condition and residence times of gas and solid in the riser are very short. If the reaction rate of catalyst or sorbent is slow, the riser can not ensure sufficient contact time between gas and solid and we have to use two bubbling beds for each reaction to ensure sufficient contact time. In this case, additional riser must be installed for solid circulation. Consequently, conventional two-interconnected fluidized bed systems are very complex, large, and difficult to operate. To solve these problems, a novel two-interconnected fluidized bed system has been developed. This system has two bubbling beds, solid injection nozzles, solid conveying lines, and downcomers. In this study, effects of operating variables on solid circulation rate, gas leakage between two beds have been investigated in a cold mode two-interconnected fluidized bed system. Moreover, long-term operation of continuous solid circulation up to 60 hours has been performed to check feasibility of stable operation.
Abstract: Universities have an important role in social education in many aspects. In terms of creating awareness and convincing public about social issues, universities take a leading position for public. The best way to provide public support for social education is to develop public communication campaigns. The aim of this study is to present a public communication model which will be guided in social education practices. The study titled “Importance of public communication campaigns and art activities in Social Education “is based on the following topics: Effects of public communication campaigns on social education, Public relations techniques for education, communication strategies, Steps of public relations campaigns in social education, making persuasive messages for public communication campaigns, developing artistic messages and organizing art activities in social education. In addition to these topics, media planning for social education, forming a team as campaign managers, dialogues with opinion leaders in education and preparing creative communication models for social education will be taken into consideration. This study also aims to criticize social education Case studies in Turkey. At the same time, some communicative methods and principles will be given in the light of communication campaigns within the context of this notice.
Abstract: This paper reports on an effort to address the issue of
inequality in girls- and women-s access to science, engineering and
technology (SET) education and careers through raising awareness on
SET among secondary school girls in South Africa. Girls participated
in hands-on high-tech rapid prototyping environment of a fabrication
laboratory that was aimed at stimulating creativity and innovation as
part of a Fab Kids initiative. The Fab Kids intervention is about
creating a SET pipeline as part of the Young Engineers and Scientists
of Africa Initiative.The methodology was based on a real world
situation and a hands-on approach. In the process, participants
acquired a number of skills including computer-aided design,
research skills, communication skills, teamwork skills, technical
drawing skills, writing skills and problem-solving skills. Exposure to
technology enhanced the girls- confidence in being able to handle
technology-related tasks.
Abstract: In this work, we propose a hybrid heuristic in order to
solve the Team Orienteering Problem (TOP). Given a set of points (or
customers), each with associated score (profit or benefit), and a team
that has a fixed number of members, the problem to solve is to visit a
subset of points in order to maximize the total collected score. Each
member performs a tour starting at the start point, visiting distinct
customers and the tour terminates at the arrival point. In addition,
each point is visited at most once, and the total time in each tour
cannot be greater than a given value. The proposed heuristic combines
beam search and a local optimization strategy. The algorithm was
tested on several sets of instances and encouraging results were
obtained.
Abstract: In process control applications, above 90% of the
controllers are of PID type. This paper proposed a robust PI
controller with fractional-order integrator. The PI parameters were
obtained using classical Ziegler-Nichols rules but enhanced with the
application of error filter cascaded to the fractional-order PI. The
controller was applied on steam temperature process that was
described by FOPDT transfer function. The process can be classified
as lag dominating process with very small relative dead-time. The
proposed control scheme was compared with other PI controller
tuned using Ziegler-Nichols and AMIGO rules. Other PI controller
with fractional-order integrator known as F-MIGO was also
considered. All the controllers were subjected to set point change and
load disturbance tests. The performance was measured using Integral
of Squared Error (ISE) and Integral of Control Signal (ICO). The
proposed controller produced best performance for all the tests with
the least ISE index.
Abstract: In this study, oxidative steam reforming of methanol (OSRM) over a Au/CeO2–Fe2O3 catalyst prepared by a depositionprecipitation (DP) method was studied to produce hydrogen in order to feed a Proton Exchange Membrane Fuel Cell (PEMFC). The support (CeO2, Fe2O3, and CeO2–Fe2O3) were prepared by precipitation and co-precipitation methods. The impact of the support composition on the catalytic performance was studied by varying the Ce/(Ce+Fe) atomic ratio, it was found that the 1%Au/CF(0.25) calcined at 300 °C exhibited the highest catalytic activity in the whole temperature studied. In addition, the effect of Au content was investigated and 3%Au/CF(0.25) exhibited the highest activity under the optimum condition in the temperature range of 200 °C to 400 °C. The catalysts were characterized by various techniques: XRD, TPR, XRF, and UV-vis.
Abstract: This research presents a fuzzy multi-objective model
for a machine selection problem in a flexible manufacturing system
of a tire company. Two main objectives are minimization of an
average machine error and minimization of the total setup time.
Conventionally, the working team uses trial and error in selecting a
pressing machine for each task due to the complexity and constraints
of the problem. So, both objectives may not satisfy. Moreover, trial
and error takes a lot of time to get the final decision. Therefore, in
this research preemptive fuzzy goal programming model is developed
for solving this multi-objective problem. The proposed model can
obtain the appropriate results that the Decision Making (DM) is
satisfied for both objectives. Besides, alternative choice can be easily
generated by varying the satisfaction level. Additionally, decision
time can be reduced by using the model, which includes all
constraints of the system to generate the solutions. A numerical
example is also illustrated to show the effectiveness of the proposed
model.
Abstract: The objective of this paper is to present the
development of the frame of Chulalongkorn University team in TSAE
Auto Challenge Student Formula and Student Formula SAE
Competition of Japan. Chulalongkorn University's SAE team, has
established since year 2003, joined many competitions since year 2006
and became the leading team in Thailand. Through these 5 years, space
frame was the most selected and developed year by year through six
frame designs. In this paper, the discussions on the conceptual design
of these frames are introduced, focusing on the mass and torsional
stiffness improvement. The torsional stiffness test was performed on
the real used frames and the results are compared. It can be seen that
the 2010-2011 frame is firstly designed based on the analysis and
experiment that considered the required mass and torsional stiffness.
From the torsional stiffness results, it can be concluded that the frames
were developed including the decreasing of mass and the increasing
torsional stiffness by applying many techniques.
Abstract: Peer review is an activity where students review their
classmates- writing and then evaluate the content, development, unity
and organization. Studies have shown that peer review activities
benefit both the reviewer and the writer in developing their reading
and writing skills. Furthermore, peer review activities may also
enhance students- soft skills. This study was conducted to find out the
benefits of peer review activity in a technical writing class based on
engineering students- perceptions. The study also highlights how
these benefits could improve the students- soft skills. A set of
questionnaire was given to 200 undergraduate students of a technical
writing course. The results of the study indicate that the activity could
help improve their critical thinking skills, written and oral
communication skills, as well as team work. This paper further
discusses how the implications of these benefits could help enhance
students- soft skills.
Abstract: One part of the total employee-s reward is apart from basic wages or salary, employee-s benefits and intangible elements also so called contingent (variable) pay. Contingent pay is connected to performance, contribution, capcompetency or skills of individual employees, and to team-s or company-wide performance or to combination of few of the mentioned possibilities. Main aim of this article is to define, based on available information, contingent pay, describe reasons for its implementation and arguments for and against this type of remuneration, but also bring information not only about its extent and level of utilization by organizations of the Czech Republic operating in the field of environmental protection, but also mention their practical experience with this type of remuneration.
Abstract: Bond Graph as a unified multidisciplinary tool is widely
used not only for dynamic modelling but also for Fault Detection and
Isolation because of its structural and causal proprieties. A binary
Fault Signature Matrix is systematically generated but to make the
final binary decision is not always feasible because of the problems
revealed by such method. The purpose of this paper is introducing a
methodology for the improvement of the classical binary method of
decision-making, so that the unknown and identical failure signatures
can be treated to improve the robustness. This approach consists of
associating the evaluated residuals and the components reliability data
to build a Hybrid Bayesian Network. This network is used in two
distinct inference procedures: one for the continuous part and the
other for the discrete part. The continuous nodes of the network are
the prior probabilities of the components failures, which are used by
the inference procedure on the discrete part to compute the posterior
probabilities of the failures. The developed methodology is applied
to a real steam generator pilot process.
Abstract: Measurements of capacitance C and dissipation
factor tand of the stator insulation system provide useful information
about internal defects within the insulation. The index k is defined as
the proportionality constant between the changes at high voltage of
capacitance DC and of the dissipation factor Dtand . DC and
Dtand values were highly correlated when small flat defects were
within the insulation and that correlation was lost in the presence of
large narrow defects like electrical treeing. The discrimination
between small and large defects is made resorting to partial discharge
PD phase angle analysis. For the validation of the results, C and tand
measurements were carried out in a 15MVA 4160V steam turbine
turbogenerator placed in a sugar mill. In addition, laboratory test
results obtained by other authors were analyzed jointly. In such
laboratory tests, model coil bars subjected to thermal cycling resulted
highly degraded and DC and Dtand values were not correlated. Thus,
the index k could not be calculated.
Abstract: At present time, competition, unpredictable fluctuations have made communication engineering education in the global sphere really difficult. Confront with new situation in the engineering education sector. Communication engineering education has to be reformed and ready to use more advanced technologies. We realized that one of the general problems of student`s education is that after graduating from their universities, they are not prepared to face the real life challenges and full skilled to work in industry. They are prepared only to think like engineers and professionals but they also need to possess some others non-technical skills. In today-s environment, technical competence alone is not sufficient for career success. Employers want employees (graduate engineers) who have good oral and written communication (soft) skills. It does require for team work, business awareness, organization, management skills, responsibility, initiative, problem solving and IT competency. This proposed curriculum brings interactive, creative, interesting, effective learning methods, which includes online education, virtual labs, practical work, problem-based learning (PBL), and lectures given by industry experts. Giving short assignments, presentations, reports, research papers and projects students can significantly improve their non-technical skills. Also, we noticed the importance of using ICT technologies in engineering education which used by students and teachers, and included that into proposed teaching and learning methods. We added collaborative learning between students through team work which builds theirs skills besides course materials. The prospective on this research that we intent to update communication engineering curriculum in order to get fully constructed engineer students to ready for real industry work.
Abstract: Dill contains range of phytochemicals, such as vitamin C and polyphenols, which significantly contribute to their total antioxidant activity. The aim of the current research was to determine the best blanching method for processing of dill prior to microwave vacuum drying based on the content of phenolic compounds, vitamin C and free radical scavenging activity. Two blanching mediums were used – water and steam, and for part of the samples microwave pretreatment was additionally used. Evaluation of vitamin C, phenolic contents and scavenging of DPPH˙ radical in dried dill was performed. Blanching had an effect on all tested parameters and the blanching conditions are very important. After evaluation of the results, as the best method for dill pretreatment was established blanching at 90 °C for 30 seconds.
Abstract: Nowadays, desalination of salt water is considered an important industrial process. In many parts of the world, particularly in the gulf countries, the multi-stage flash (MSF) water desalination has an essential contribution in the production of fresh water. In this study, a simple mathematical model is defined to design a MSF desalination system and the feasibility of using the MSF desalination process in proximity of a 42 MW power plant is investigated. This power plant can just provide 10 ton/h superheated steam from low pressure (LP) section of heat recovery steam generator (HRSG) for thermal desalting system. The designed MSF system with gained output ratio (GOR) of 10.3 has 24 flashing stages and can produce 2480 ton/d of fresh water. The expected performance characteristics of the designed MSF desalination plant are determined. In addition, the effect of motive water pressure on the amount of non-condensable gases removed by water jet vacuum pumps is investigated.