Abstract: The use of low quality concrete has been identified as one of the main causes of the incessant collapse of buildings in Nigeria. Emphasis has been on the use of poor quality aggregates, poor workmanship and the use of lean concrete mix with low cement quantity as the reasons for the low quality of concrete used for building construction in Nigeria. Surveys conducted revealed that in the construction of most privately owned buildings where concrete trial mixes and concrete compressive strength quality assurance tests are not conducted, concretes used for building constructions are produced using the 1:2:4 mix ratio irrespective of the cement grade/strength class. In this paper, the possible role of the use of inappropriate cement grade/strength class as a cause of the incessant collapse of building in Nigeria is investigated. Investigation revealed that the compressive strengths of concrete cubes produced with Portland-limestone cement grade 32.5 using 1:2:4 and 1:1.5:3 mix ratios are less than the 25MPa and 30MPa cube strengths generally recommended for building superstructures and foundations respectively. Conversely, the compressive strengths of concrete cubes produced with Portland-limestone cement grade 42.5 using 1:2:4 and 1:1.5:3 mix ratios exceed the 25MPa and 30MPa generally recommended for building superstructures and foundations respectively. Thus, it can be concluded that the use of inappropriate cement grade (Portland-limestone cement grade 32.5), particularly for the construction of building foundations is a potential cause of the incessant collapse of buildings in Nigeria. It is recommended that the Standards Organisation of Nigeria should embark on creating awareness for Nigerians, particularly, the home owners and the roadside craftsmen that Portland-limestone cement grade 32.5 should not be used for the construction of building load-carrying members, particularly, building foundations in order to reduce the incessant incidence of collapsed building.
Abstract: This article aims to study the effect of pressure on rocket motor case by Finite Element Method simulation to select optimal material in rocket motor manufacturing process. In this study, cylindrical tubes with outside diameter of 122 mm and thickness of 3 mm are used for simulation. Defined rocket motor case materials are AISI4130, AISI1026, AISI1045, AL2024 and AL7075. Internal pressure used for the simulation is 22 MPa.
The result from Finite Element Method shows that at a pressure of 22 MPa rocket motor case produced by AISI4130, AISI1045 and AL7075 can be used. A comparison of the result between AISI4130, AISI1045 and AL7075 shows that AISI4130 has minimum principal stress and confirm the results of Finite Element Method by the used of calculation method found that, the results from Finite Element Method has good reliability.
Abstract: Developing a reliable and sustainable software products is today a big challenge among up–coming software developers in Nigeria. The inability to develop a comprehensive problem statement needed to execute proper requirements engineering process is missing. The need to describe the ‘what’ of a system in one document, written in a natural language is a major step in the overall process of Software Engineering. Requirements Engineering is a process use to discover, analyze and validate system requirements. This process is needed in reducing software errors at the early stage of the development of software. The importance of each of the steps in Requirements Engineering is clearly explained in the context of using detailed problem statement from client/customer to get an overview of an existing system along with expectations from the new system. This paper elicits inadequate Requirements Engineering principle as the major cause of poor software development in developing nations using a case study of final year computer science students of a tertiary-education institution in Nigeria.
Abstract: The expanded Invasive Weed Optimization algorithm (exIWO) is an optimization metaheuristic modelled on the original IWO version created by the researchers from the University of Tehran. The authors of the present paper have extended the exIWO algorithm introducing a set of both deterministic and non-deterministic strategies of individuals’ selection. The goal of the project was to evaluate the exIWO by testing its usefulness for solving some test instances of the traveling salesman problem (TSP) taken from the TSPLIB collection which allows comparing the experimental results with optimal values.
Abstract: Among agricultural residues, sugarcane bagasse is one of the most convincing raw materials for the production of bioethanol due to its availability, and low cost through enzymatic hydrolysis and yeast fermentation. A pretreatment step is needed to enhance the enzymatic step. In this study, sugarcane bagasse (SCB), one of the most abundant agricultural residues in Thailand, was pretreated biologically with various microorganisms of white-rot fungus—Phanerochaete sordid (SK 7), Cellulomonas sp. (TISTR 784), and strain A 002 (Bacillus subtilis isolated from Thai higher termites). All samples with various microbial pretreatments were further hydrolyzed enzymatically by a commercial enzyme obtained from Aspergillus niger. The results showed that the pretreatment with the white-rot fungus gave the highest glucose concentration around two-fold higher when compared with the others.
Abstract: In this study, we will touch upon the legal arrangements issued in Turkey for prevention of condensation and for ensuring pluralism in the media. We will mention the legal arrangements concerning the regulatory and supervisory authority, namely the Radio and Television Supreme Council, for the visual and auditory media. In this context; the legal arrangements, which have been introduced by the Law No 6112 on the Establishment of Radio and Television Enterprises and Their Media Services in relation to the media ownership, will be reviewed through comparison with the Article 29 of the repealed Law No 3984.
Abstract: A vacuum fractionation technique was introduced to remove ethanol from fermentation broth. The effect of initial glucose and ethanol concentrations were investigated for specific productivity. The inhibitory ethanol concentration was observed at 100 g/L. In order to increase the fermentation performance, the ethanol product was removed as soon as it is produced. The broth was boiled at 35oC by reducing the pressure to 65 mBar. The ethanol/water vapor was fractionated for up to 90 wt% before leaving the column. Ethanol concentration in the broth was kept lower than 25 g/L, thus minimized the product inhibition effect to the yeast cells. For batch extractive fermentation, a high substrate utilization rate was obtained at 26.6 g/L.h and most of glucose was consumed within 21 h. For repeated-batch extractive fermentation, addition of glucose was carried out up to 9 times and ethanol was produced more than 8-fold higher than batch fermentation.
Abstract: An optimisation method using both global and local
optimisation is implemented to determine the flapping profile which
will produce the most lift for an experimental wing-actuation system.
The optimisation method is tested using a numerical quasi-steady
analysis. Results of an optimised flapping profile show a 20% increase
in lift generated as compared to flapping profiles obtained by high
speed cinematography of a Sympetrum frequens dragonfly. Initial
optimisation procedures showed 3166 objective function evaluations.
The global optimisation parameters - initial sample size and stage
one sample size, were altered to reduce the number of function
evaluations. Altering the stage one sample size had no significant
effect. It was found that reducing the initial sample size to 400
would allow a reduction in computational effort to approximately
1500 function evaluations without compromising the global solvers
ability to locate potential minima. To further reduce the optimisation
effort required, we increase the local solver’s convergence tolerance
criterion. An increase in the tolerance from 0.02N to 0.05N decreased
the number of function evaluations by another 20%. However, this
potentially reduces the maximum obtainable lift by up to 0.025N.
Abstract: Climate change and poverty are global issues which cannot be waved aside in welfare of the ever increasing population. The causes / consequences are far more elaborate in developing countries, including Nigeria, which poses threats to the existence of man and his environment. The dominant role of agriculture makes it obvious that even minor climate deteriorations can cause devastating socio-economic consequences. Policies to curb the climate change by reducing the consumption of fossil fuels like oil, gas or carbon compounds have significant economical impacts on the producers/suppliers of these fuels. Thus a unified political narrative that advances both agendas is needed, because their components of an environmental coin that needs to be addressed. The developed world should maintain a low-carbon growth & real commitment of 0.7% of gross national income, as aid to developing countries & renewable energy approach should be emphasized, hence global poverty combated.
Abstract: Most of the PV systems are designed with transformer for safety purpose with galvanic isolation. However, the transformer is big, heavy and expensive. Also, it reduces the overall frequency of the conversion stage. Generally PV inverter with transformer is having efficiency around 92%–94% only. To overcome these problems, transformerless PV system is introduced. It is smaller, lighter, cheaper and higher in efficiency. However, dangerous leakage current will flow between PV array and the grid due to the stray capacitance. There are different types of configurations available for transformerless inverters like H5, H6, HERIC, oH5, and Dual paralleled buck inverter. But each configuration is suffering from its own disadvantages like high conduction losses, shoot-through issues of switches, dead-time requirements at zero crossing instants of grid voltage to avoid grid shoot-through faults and MOSFET reverse recovery issues. The main objective of the proposed transformerless inverter is to address two key issues: One key issue for a transformerless inverter is that it is necessary to achieve high efficiency compared to other existing inverter topologies. Another key issue is that the inverter configuration should not have any shoot-through issues for higher reliability.
Abstract: The society of 3rd Generation Partnership Project (3GPP) is completed developing Long Term Evolution Advanced (LTE-Advanced) systems as a standard 4G cellular system. This generation goals to produce conditions for a new radio-access technology geared to higher data rates, low latency, and better spectral efficiency. LTE-Advanced is an evolutionary step in the continuing development of LTE where the description in this article is based on LTE release 10. This paper provides a model of the traffic links of 4G system represented by LTE-Advanced system with the effect of the Transmission Control Protocols (TCP) and Stream Control Transmission Protocol (SCTP) in term of throughput and packet loss. Furthermore, the article presents the investigation and the analysis the behavior of SCTP and TCP variants over the 4G cellular systems. The traffic model and the scenario of the simulation developed using the network simulator NS-2 using different TCP source variants.
Abstract: This research aimed to produce offset printing inks from Samut Songkram’s coconut oil and to test properties of the printing inks comparing with commercial offset printing inks. One of the ingredients in the process of mixing varnish is coconut oil – used to produce black offset printing inks which were the subject of testing issues in order to compare with commercial offset printing inks. Based on the results of research, the best formula for mixing varnish was 50% of coconut oil, 36% of phenolic resin, and 14% of solvent oil. At the same time, the best formula in producing black offset inks was mixing varnish with 20% of coconut oil 20%. Consequently, the result of testing of properties of coconut oil based solvent offset printing inks regarding viscosity, tack and ink flow, showed that offset printing inks with oil based solvent had the properties less than commercial offset printing ink. Additionally, the result of testing also indicate that the rate of properties in aspects of ink spread and setting time of coconut oil based solvent offset printing were higher than that of commercial offset printing inks.
Abstract: A continuous time model of the interaction between
crop insect pests and naturally beneficial pest enemies is created
using a set of simultaneous, non-linear, ordinary differential
equations incorporating natural death rates based on the Weibull
distribution. The crop pest is present in all its life-cycle stages of:
egg, larva, pupa and adult. The beneficial insects, parasitoid wasps,
may be present in either or all parasitized: eggs, larva and pupa.
Population modelling is used to estimate the quantity of the natural
pest enemies that should be introduced into the pest infested
environment to suppress the pest population density to an
economically acceptable level within a prescribed number of days.
The results obtained illustrate the effect of different combinations of
parasitoid wasps, using the Pascal distribution to estimate their
success in parasitizing different pest developmental stages, to deliver
pest control to a sustainable level. Effective control, within a
prescribed number of days, is established by the deployment of two
or all three species of wasps, which partially destroy pest: egg, larvae
and pupae stages. The selected scenarios demonstrate effective
sustainable control of the pest in less than thirty days.
Abstract: Soy protein is a common ingredient added to processed meats to enhance its functional characteristics. In our study, soybean products (fermented soy Natto and protein hydrolysate) containing hydrolyzed peptides and amino acids, with or without ascorbic acid were added to burger in order to improve its quality characteristics. Results showed that soy additives significantly increased moisture and protein content and reduced (P < 0.05) fat values. Ash content did not affect with Natto additive. Color tools, lightness and yellowness were higher (P
Abstract: Biometallic materials are the most important materials for use in biomedical applications especially in manufacturing a variety of biological artificial replacements in a modern worlds, e.g. hip, knee or shoulder joints, due to their advanced characteristics. Titanium (Ti) and its alloys are used extensively in biomedical applications based on their high specific strength and excellent corrosion resistance. Beta-Ti alloys containing completely biocompatible elements are exceptionally prospective materials for manufacturing of bioimplants. They have superior mechanical, chemical and electrochemical properties for use as biomaterials. These biomaterials have the ability to introduce the most important property of biochemical compatibility which is low elastic modulus. This review examines current information on the recent developments in alloying elements leading to improvements of beta Ti alloys for use as biomaterials. Moreover, this paper focuses mainly on the evolution, evaluation and development of the modulus of elasticity as an effective factor on the performance of beta alloys.
Abstract: When it comes to last, it is regarded as the critical foundation of shoe design and development. Not only the last relates to the comfort of shoes wearing but also it aids the production of shoe styling and manufacturing. In order to enhance the efficiency and application of last development, a computer aided methodology for customized last form designs is proposed in this study. The reverse engineering is mainly applied to the process of scanning for the last form. Then the minimum energy is used for the revision of surface continuity, the surface of the last is reconstructed with the feature curves of the scanned last. When the surface of a last is reconstructed, based on the foundation of the proposed last form reconstruction module, the weighted arithmetic mean method is applied to the calculation on the shape morphing which differs from the grading for the control mesh of last, and the algorithm of subdivision is used to create the surface of last mesh, thus the feet-fitting 3D last form of different sizes is generated from its original form feature with functions remained. Finally, the practicability of the proposed methodology is verified through later case studies.
Abstract: In recent years, in addition to face the external threats such as energy shortages and climate change, traffic congestion and environmental pollution have become anxious problems for many cities. Considering private automobile-oriented urban development had produced many negative environmental and social impacts, the transit-oriented development (TOD) has been considered as a sustainable urban model. TOD encourages public transport combined with friendly walking and cycling environment designs, however, non-motorized modes help improving human health, energy saving, and reducing carbon emissions. Due to environmental changes often affect the planners’ decision-making; this research applies dynamic network process (DNP) which includes the time dependent concept to promoting friendly walking and cycling environmental designs as an advanced planning support system for environment improvements.
This research aims to discuss what kinds of design strategies can improve a friendly walking and cycling environment under TOD. First of all, we collate and analyze environment designing factors by reviewing the relevant literatures as well as divide into three aspects of “safety”, “convenience”, and “amenity” from fifteen environment designing factors. Furthermore, we utilize fuzzy Delphi Technique (FDT) expert questionnaire to filter out the more important designing criteria for the study case. Finally, we utilized DNP expert questionnaire to obtain the weights changes at different time points for each design criterion. Based on the changing trends of each criterion weight, we are able to develop appropriate designing strategies as the reference for planners to allocate resources in a dynamic environment. In order to illustrate the approach we propose in this research, Taipei city as one example has been used as an empirical study, and the results are in depth analyzed to explain the application of our proposed approach.
Abstract: Assistive robotics are playing a vital role in advancing the quality of life for disable people. There exist wide range of systems that can control and guide autonomous mobile robots. The objective of the control system is to guide an autonomous mobile robot using the movement of eyes by means of EOG signal. The EOG signal is acquired using Ag/AgCl electrodes and this signal is processed by a microcontroller unit to calculate the eye gaze direction. Then according to the guidance control strategy, the control commands of the wheelchair are sent. The classification of different eye movements allows us to generate simple code for controlling the wheelchair. This work was aimed towards developing a usable and low-cost assistive robotic wheel chair system for disabled people. To live more independent life, the system can be used by the handicapped people especially those with only eye-motor coordination.
Abstract: Metal matrix composites (MMCs) have gained a
considerable interest in the last three decades. Conventional powder
metallurgy production route often involves the addition of reinforcing
phases into the metal matrix directly, which leads to poor wetting
behavior between ceramic phase and metal matrix and the
segregation of reinforcements. The commonly used elements for
ceramic phase formation in iron based MMCs are Ti, Nb, Mo, W, V
and C, B. The aim of the present paper is to investigate the effect of
sintering temperature and V-B addition on densification, phase
development, microstructure, and hardness of Fe–V-B composites
(Fe-(5-10) wt. %B – 25 wt. %V alloys) prepared by powder
metallurgy process. Metal powder mixes were pressed uniaxial and
sintered at different temperatures (ranging from 1300 to 1400ºC) for
1h. The microstructure of the (V, B) Fe composites was studied with
the help of high magnification optical microscope and XRD.
Experimental results show that (V, B) Fe composites can be produced
by conventional powder metallurgy route.
Abstract: Analysis of EEG brainwave provides information on mental or emotional states. One of the particular states that can have various applications in human machine interface (HMI) is concentration. 8-channel EEG signals were measured and analyzed. The concentration index was compared during resting and concentrating periods. Among eight channels, locations the frontal lobe (Fp1 and Fp2) showed a clear increase of the concentration index during concentration regardless of subjects. The rest six channels produced conflicting observations depending on subjects. At this time, it is not clear whether individual difference or how to concentrate made these results for the rest six channels. Nevertheless, it is expected that Fp1 and Fp2 are promising locations for extracting control signal for HMI applications.