Abstract: In this paper, the application of thermal spray
coatings in high speed shafts by a revolution up to 23000 RPM
has been studied. Gas compressor shafts are worn in contact
zone with journal therefore will be undersized. Wear
mechanisms of compressor shaft were identified. The
predominant wear mechanism is abrasion wear. The worn
surface was coated by hard WC-Co cermets using high
velocity oxy fuel (HVOF) after preparation. The shafts were in
satisfactory service in 8000h period. The metallurgical and
Tribological studies has been made on the worn and coated
shaft using optical microscopy, scanning electron microscopy
(SEM) and X-ray diffraction.
Abstract: The aim of this study is to develop mathematical
relationships for the performance parameter brake thermal efficiency
(BTE) and emission parameter nitrogen oxides (NOx) for the various
esters of vegetable oils used as CI engine fuel. The BTE is an
important performance parameter defining the ability of engine to
utilize the energy supplied and power developed similarly it is
indication of efficiency of fuels used. The esters of cottonseed oil,
soybean oil, jatropha oil and hingan oil are prepared using
transesterification process and characterized for their physical and
main fuel properties including viscosity, density, flash point and
higher heating value using standard test methods. These esters are
tried as CI engine fuel to analyze the performance and emission
parameters in comparison to diesel. The results of the study indicate
that esters as a fuel does not differ greatly with that of diesel in
properties. The CI engine performance with esters as fuel is in line
with the diesel where as the emission parameters are reduced with the
use of esters.
The correlation developed between BTE and brake power(BP),
gross calorific value(CV), air-fuel ratio(A/F), heat carried away by
cooling water(HCW). Another equation is developed between the
NOx emission and CO, HC, smoke density (SD), exhaust gas
temperature (EGT). The equations are verified by comparing the
observed and calculated values which gives the coefficient of
correlation of 0.99 and 0.96 for the BTE and NOx equations
respectively.
Abstract: In this work we study the effect of several covariates X on a censored response variable T with unknown probability distribution. In this context, most of the studies in the literature can be located in two possible general classes of regression models: models that study the effect the covariates have on the hazard function; and models that study the effect the covariates have on the censored response variable. Proposals in this paper are in the second class of models and, more specifically, on least squares based model approach. Thus, using the bootstrap estimate of the bias, we try to improve the estimation of the regression parameters by reducing their bias, for small sample sizes. Simulation results presented in the paper show that, for reasonable sample sizes and censoring levels, the bias is always smaller for the new proposals.
Abstract: This study reports results of a meta-analytic path analysis e-learning Acceptance Model with k = 27 studies, Databases searched included Information Sciences Institute (ISI) website. Variables recorded included perceived usefulness, perceived ease of use, attitude toward behavior, and behavioral intention to use e-learning. A correlation matrix of these variables was derived from meta-analytic data and then analyzed by using structural path analysis to test the fitness of the e-learning acceptance model to the observed aggregated data. Results showed the revised hypothesized model to be a reasonable, good fit to aggregated data. Furthermore, discussions and implications are given in this article.
Abstract: This study investigated the relationship between urban
and rural ozone concentrations and quantified the extent to which
ambient rural conditions and the concentrations of other pollutants
can be used to predict urban ozone concentrations. The study
describes the variations of ozone in weekday and weekends as well as
the daily maximum recorded at selected monitoring stations. The
results showed that Putrajaya station had the highest concentrations
of O3 on weekend due the titration of NO during the weekday.
Additionally, Jerantut had the lowest average concentration with a
reading value high on Wednesdays. The comparisons of average and
maximum concentrations of ozone for the three stations showed that
the strongest significant correlation is recorded in Jerantut station
with the value R2= 0.769. Ozone concentrations originating from a
neighbouring urban site form a better predictor to the urban ozone
concentrations than widespread rural ozone at some levels of
temporal averaging. It is found that in urban and rural of Malaysian
peninsular, the concentration of ozone depends on the concentration
of NOx and seasonal meteorological factors. The HYSPLIT Model
(the northeast monsoon) showed that the wind direction can also
influence the concentration of ozone in the atmosphere in the studied
areas.
Abstract: The electrical interaction between two axisymmetric
spheroidal particles in an electrolyte solution is examined numerically.
A Galerkin finite element method combined with a Newton-Raphson
iteration scheme is proposed to evaluate the spatial variation in the
electrical potential, and the result obtained used to estimate the
interaction energy between two particles. We show that if the surface
charge density is fixed, the potential gradient is larger at a point, which
has a larger curvature, and if surface potential is fixed, surface charge
density is proportional to the curvature. Also, if the total interaction
energy against closest surface-to-surface curve exhibits a primary
maximum, the maximum follows the order (oblate-oblate) >
(sphere-sphere)>(oblate-prolate)>(prolate-prolate), and if the curve
has a secondary minimum, the absolute value of the minimum follows
the same order.
Abstract: The main criteria of designing in the most hydraulic
constructions essentially are based on runoff or discharge of water. Two of those important criteria are runoff and return period. Mostly,
these measures are calculated or estimated by stochastic data.
Another feature in hydrological data is their impreciseness.
Therefore, in order to deal with uncertainty and impreciseness, based
on Buckley-s estimation method, a new fuzzy method of evaluating hydrological measures are developed. The method introduces
triangular shape fuzzy numbers for different measures in which both
of the uncertainty and impreciseness concepts are considered. Besides, since another important consideration in most of the
hydrological studies is comparison of a measure during different
months or years, a new fuzzy method which is consistent with special form of proposed fuzzy numbers, is also developed. Finally, to
illustrate the methods more explicitly, the two algorithms are tested on one simple example and a real case study.
Abstract: The following study aims to outline, whether the
perceptions of entrepreneurs about their entrepreneurial activities and
the underlying meanings of their activities are universal or whether
they vary systematically across cultures. In contrast to previous
studies, the phenomenographical approach and the resulting findings
of this study provide new insights into what constitutes
entrepreneurship by drawing an inference from the perceptions of
entrepreneurs in the United States and in Germany. Culture is shown
to have an important impact on entrepreneurship, since the
underlying meanings of entrepreneurship vary significantly among
the two sample groups. Furthermore, the study sheds more light on
the culturally contingent 'why' of entrepreneurship by looking at the
internal motivations of individuals instead of exclusively focusing on
character traits or external influences of the respective economic
environments.
Abstract: Today, people are more interested in the foods
beneficial on their health. However, there are still lacks of accurate
knowledge in the field of biological properties, functional properties,
including the application of legume in foods. This study focused on
antioxidant activity of soybean (SB) and fermented soybean (FSB)
crude extracts evaluating to have more information in fortification SB
and FSB crude extracts in food products and/or dietary supplement.
SB and FSB crude extracts were prepared by infusion with water and
ethanol. The antioxidant activity of crude extracts was studied with
DPPH and ABTS assay including commercial standard. From both
DPPH and ABTS assay, the antioxidant activity of SB and FSB water
crude extract showed higher antioxidant activity than ethanol crude
extract, and FSB crude extract showed higher antioxidant activity
than SB crude extract. In DPPH assay, BHT and vitamin C showed
IC50 values at 0.241, 0.039 mg/ml, in ABTS assay. In addition,
Trolox showed IC50 at 0.058 mg/ml respectively. FSB water crude
extract showed high antioxidant activity. Finally, the functional
properties study of both water and ethanol crude extracts should be
done for beneficial in application of these extracts in food products
and dietary supplement in the near future.
Abstract: An electrical apparatus for measuring moisture
content was developed by our laboratory and uses dependence of
electrical properties on water content in studied material. Error
analysis of the apparatus was run by measuring different volumes of
water in a simplified specimen, i.e. hollow plexiglass block, in order
to avoid as many side-effects as possible. Obtained data were
processed using both basic and advanced statistics and results were
compared with each other. The influence of water content on
accuracy of measured data was studied as well as the influence of
variation of apparatus' proper arrangement or factual methodics of its
usage. The overall coefficient of variation was 4%. There was no
trend found in results of error dependence on water content.
Comparison with current surveys led to a conclusion, that the studied
apparatus can be used for indirect measurement of water content in
porous materials, with expectable error and under known conditions.
Factual experiments with porous materials are not involved, but are
currently under investigation.
Abstract: This study was aimed to study the probability about
the production of fiberboard made of durian rind through latex with
phenolic resin as binding agent. The durian rind underwent the
boiling process with NaOH [7], [8] and then the fiber from durian
rind was formed into fiberboard through heat press. This means that
durian rind could be used as replacement for plywood in plywood
industry by using durian fiber as composite material with adhesive
substance. This research would study the probability about the
production of fiberboard made of durian rind through latex with
phenolic resin as binding agent. At first, durian rind was split,
exposed to light, boiled and steamed in order to gain durian fiber.
Then, fiberboard was tested with the density of 600 Kg/m3 and 800
Kg/m3. in order to find a suitable ratio of durian fiber and latex.
Afterwards, mechanical properties were tested according to the
standards of ASTM and JIS A5905-1994. After the suitable ratio was
known, the test results would be compared with medium density
fiberboard (MDF) and other related research studies. According to
the results, fiberboard made of durian rind through latex with
phenolic resin at the density of 800 Kg/m3 at ratio of 1:1, the
moisture was measured to be 5.05% with specific gravity (ASTM D
2395-07a) of 0.81, density (JIS A 5905-1994) of 0.88 g/m3, tensile
strength, hardness (ASTM D2240), flexibility or elongation at break
yielded similar values as the ones by medium density fiberboard
(MDF).
Abstract: In this article, biomechanical aspects of hen-s eggshell as a natural ceramic structure are studied. The images, taken by a scanning electron microscope (SEM), are used to investigate the microscopic aspects of the egg. It is observed that eggshell has a three-layered microstructure with different morphological and structural characteristics. Studies on the eggshell membrane (ESM) as a prosperous tissue suggest that it is placed to prevent the penetration of microorganisms into the egg. Finally, numerical models of the egg are presented to study the stress distribution and its deformation under different loading conditions. The effects of two different types of loading (hydrostatic and point loadings) on two different shell models (with constant and variable thicknesses) are investigated in detail.
Abstract: We investigated a modified thermal evaporation
method in the growth process of ZnO nanowires. ZnO nanowires
were fabricated on p-type silicon substrates without using a metal
catalyst. A simple horizontal double-tube system along with
chemical vapor diffusion of the precursor was used to grow the ZnO
nanowires. The substrates were placed in different temperature
zones, and ZnO nanowires with different diameters were obtained for
the different substrate temperatures. In addition to the nanowires,
ZnO microdiscs with different diameters were obtained on another
substrate, which was placed at a lower temperature than the other
substrates. The optical properties and crystalline quality of the ZnO
nanowires and microdiscs were characterized by room temperature
photoluminescence (PL) and Raman spectrometers. The PL and
Raman studies demonstrated that the ZnO nanowires and microdiscs
grown using such set-up had good crystallinity with excellent optical
properties. Rectifying behavior of ZnO/Si heterostructures was
characterized by a simple DC circuit.
Abstract: The worldwide prevalence of H3N2 influenza virus
and its increasing resistance to the existing drugs necessitates for the
development of an improved/better targeting anti-influenza drug.
H3N2 influenza neuraminidase is one of the two membrane-bound
proteins belonging to group-2 neuraminidases. It acts as key player
involved in viral pathogenicity and hence, is an important target of
anti-influenza drugs. Oseltamivir is one of the potent drugs targeting
this neuraminidase. In the present work, we have taken subtype N2
neuraminidase as the receptor and probable analogs of oseltamivir as
drug molecules to study the protein-drug interaction in anticipation of
finding efficient modified candidate compound. Oseltamivir analogs
were made by modifying the functional groups using Marvin Sketch
software and were docked using Schrodinger-s Glide. Oseltamivir
analog 10 was detected to have significant energy value (16% less
compared to Oseltamivir) and could be the probable lead molecule. It
infers that some of the modified compounds can interact in a novel
manner with increased hydrogen bonding at the active site of
neuraminidase and it might be better than the original drug. Further
work can be carried out such as enzymatic inhibition studies;
synthesis and crystallizing the drug-target complex to analyze the
interactions biologically.
Abstract: Scarcity of resources for biodiversity conservation gives rise to the need of strategic investment with priorities given to the cost of conservation. While the literature provides abundant methodological options for biodiversity conservation; estimating true cost of conservation remains abstract and simplistic, without recognising dynamic nature of the cost. Some recent works demonstrate the prominence of economic theory to inform biodiversity decisions, particularly on the costs and benefits of biodiversity however, the integration of the concept of true cost into biodiversity actions and planning are very slow to come by, and specially on a farm level. Conservation planning studies often use area as a proxy for costs neglecting different land values as well as protected areas. These literature consider only heterogeneous benefits while land costs are considered homogenous. Analysis with the assumption of cost homogeneity results in biased estimation; since not only it doesn’t address the true total cost of biodiversity actions and plans, but also it fails to screen out lands that are more (or less) expensive and/or difficult (or more suitable) for biodiversity conservation purposes, hindering validity and comparability of the results. Economies of scope” is one of the other most neglected aspects in conservation literature. The concept of economies of scope introduces the existence of cost complementarities within a multiple output production system and it suggests a lower cost during the concurrent production of multiple outputs by a given farm. If there are, indeed, economies of scope then simplistic representation of costs will tend to overestimate the true cost of conservation leading to suboptimal outcomes. The aim of this paper, therefore, is to provide first road review of the various theoretical ways in which economies of scope are likely to occur of how they might occur in conservation. Consequently, the paper addresses gaps that have to be filled in future analysis.
Abstract: In this study, structural, mechanical, thermal and
electrical properties of poly (lactic acid) (PLA) nanocomposites with
low-loaded (0-1.5 wt%) untreated, heat and nitric acid treated multiwalled
carbon nanotubes (MWCNTs) were studied. Among the
composites, untreated 0.5 wt % MWCNTs and acid-treated 1.0 wt%
MWCNTs reinforced PLA show the tensile strength and modulus
values higher than the others. These two samples along with pure
PLA exhibit the stable orthorhombic α-form, whilst other samples
reveal the less stable orthorhombic β-form, as demonstrated by X-ray
diffraction study. Differential scanning calorimetry reveals the
evolution of the mentioned different phases by controlled cooling and
discloses an enhancement of PLA crystallization by nanotubes
incorporation. Thermogravimetric analysis shows that the MWCNTs
loaded sample degraded faster than PLA. Surface resistivity of the
nanocomposites is found to be dropped drastically by a factor of 1013
with a low loading of MWCNTs (1.5 wt%).
Abstract: Stochastic comparison has been an important
direction of research in various area. This can be done by the use of
the notion of stochastic ordering which gives qualitatitive rather than
purely quantitative estimation of the system under study. In this
paper we present applications of comparison based uncertainty
related to entropy in Reliability analysis, for example to design
better systems. These results can be used as a priori information in
simulation studies.
Abstract: In this paper, encrypted audio communications based on synchronization of coupled unified chaotic systems in master-slave configuration is numerically studied. We transmit the encrypted audio messages by using two unsecure channels. Encoding, transmission, and decoding audio messages in chaotic communication is presented.
Abstract: This paper explores the features of political economy in the dynamics of representative politics in India. Politics is seen as enhancing economic benefits through acquiring and maintenance of power in the realm of democratic set up. The system of representation is riddled with competitive populism. Emerging leaders and parties are forced to accommodate their ideologies in coping with competitive politics. Electoral politics and voting behaviour reflect series of influences mooted by the politicians. Voters are accustomed to expect benefits outs of state exchequer. The electoral competitors show a changing phase of investment and return policy. Every elector has to spend and realize his costs in his tenure. In the case of defeated electors, even the cost recovery is not possible directly; there are indirect means to recover their costs. The series of case studies show the method of party funding, campaign financing, electoral expenditure, and cost recovery. Regulations could not restrict the level of spending. Several cases of disproportionate accumulation of wealth by the politicians reveal that money played a major part in electoral process. The political economy of representative politics hitherto ignores how a politician spends and recovers his cost and multiples his wealth. To be sure, the acquiring and maintenance of power is to enhance the wealth of the electors.
Abstract: Tailor-welded Blanks (TWBs) are tailor made for
different complex component designs by welding multiple metal
sheets with different thicknesses, shapes, coatings or strengths prior
to forming. In this study the Hemispherical Die Stretching (HDS) test
(out-of-plane stretching) of TWBs were simulated via
ABAQUS/Explicit to obtain the Forming Limit Diagrams (FLDs) of
Stainless steel (AISI 304) laser welded blanks with different
thicknesses. Two criteria were used to detect the start of necking to
determine the FLD for TWBs and parent sheet metals. These two
criteria are the second derivatives of the major and thickness strains
that are given from the strain history of simulation. In the other word,
in these criteria necking starts when the second derivative of
thickness or major strain reaches its maximum. With having the time
of onset necking, one can measure the major and minor strains at the
critical area and determine the forming limit curve.