Abstract: A way of achieving nanodimentional structural elements in high carbon steel by special kind of heat treatment and cold plastic deformation is being explored. This leads to increasing interlamellar spacing of ferrite-carbide mixture. Decreasing the interlamellar spacing with cooling temperature increasing is determined. Experiments confirm such interlamellar spacing with which high carbon steel demonstrates the highest treatment and hardening capability. Total deformation degree effect on interlamellar spacing value in a ferrite-carbide mixture is obtained. Mechanical experiments results show that high carbon steel after heat treatment and repetitive cold plastic deformation possesses high tensile strength and yield strength keeping good percentage elongation.
Abstract: Transcription factor p53 has a powerful tumor
suppressing function that is associated with many cancers. However,
p53 of the molecular weight was higher make the limitation across to
skin or cell membrane. Thymidine dinucleotide (pTT), an
oligonucleotide, can activate the p53 transcription factor. pTT is a
hydrophilic and negative charge oligonucleotide, which delivery in to
cell membrane need an appropriate carrier. The aim of this study was
to improve the bioavailability of the nucleotide fragment, thymidine
dinucleotide (pTT), using elasic liposome carriers to deliver the drug
into the skin. The study demonstrate that dioleoylphosphocholine
(DOPC) incorporated with sodium cholate at molar ratio 1:1 can
archived the particle size about 220 nm. This elastic liposome could
penetration through skin from stratum corneum to whole epidermis by
confocal laser scanning microscopy (CLSM). Moreover, we observed
the the slight increase in generation of p53 by western blot.
Abstract: Groundwater is one of the most important water
resources in Fars province. Based on this study, 95 percent of the
total annual water consumption in Fars is used for agriculture,
whereas the percentages for domestic and industrial uses are 4 and 1
percent, respectively. Population growth, urban and industrial
growth, and agricultural development in Fars have created a
condition of water stress. In this province, farmers and other users are
pumping groundwater faster than its natural replenishment rate,
causing a continuous drop in groundwater tables and depletion of this
resource. In this research variation of groundwater level, their effects
and ways to help control groundwater levels in aquifer of the Kavar-
Maharloo plains in Fars plain were evaluated .Excessive
exploitation of groundwater in this aquifer caused the groundwater
levels fall too fast or to unacceptable levels. The average drawdown
of the groundwater level in this plain were 17 meters during
1995 to 2006. The purpose of this study is to evaluate water level
changes in the Kavar-Maharloo Aquifer in the Fars province in order
to determine the areas of greatest depletion, the cause of depletion,
and predict the remaining life of the aquifer.
Abstract: This paper reports the three-phase (gas + liquid +
hydrate) equilibrium pressure versus temperature data for a (O3 + O2 +
CO2 + H2O) system for developing the hydrate-based technology to
preserve ozone, a chemically unstable substance, for various
industrial, medical and consumer uses. These data cover the
temperature range from 272 K to 277 K, corresponding to pressures
from 1.6 MPa to 3.1 MPa, for each of the three different (O3 +
O2)-to-CO2 or O2-to-CO2 molar ratios in the gas phase, which are
approximately 4 : 6, 5 : 5, respectively. The mole fraction of ozone in
the gas phase was ~0.03 , which are the densest ozone fraction to
artificially form O3 containing hydrate ever reported in the literature.
Based on these data, the formation of hydrate containing
high-concentration ozone, as high as 1 mass %, will be expected.
Abstract: With rapid technology scaling, the proportion of the
static power consumption catches up with dynamic power
consumption gradually. To decrease leakage consumption is
becoming more and more important in low-power design. This paper
presents a power-gating scheme for P-DTGAL (p-type dual
transmission gate adiabatic logic) circuits to reduce leakage power
dissipations under deep submicron process. The energy dissipations of
P-DTGAL circuits with power-gating scheme are investigated in
different processes, frequencies and active ratios. BSIM4 model is
adopted to reflect the characteristics of the leakage currents. HSPICE
simulations show that the leakage loss is greatly reduced by using the
P-DTGAL with power-gating techniques.
Abstract: User-based Collaborative filtering (CF), one of the
most prevailing and efficient recommendation techniques, provides
personalized recommendations to users based on the opinions of other
users. Although the CF technique has been successfully applied in
various applications, it suffers from serious sparsity problems. The
cloud-model approach addresses the sparsity problems by
constructing the user-s global preference represented by a cloud
eigenvector. The user-based CF approach works well with dense
datasets while the cloud-model CF approach has a greater
performance when the dataset is sparse. In this paper, we present a
hybrid approach that integrates the predictions from both the
user-based CF and the cloud-model CF approaches. The experimental
results show that the proposed hybrid approach can ameliorate the
sparsity problem and provide an improved prediction quality.
Abstract: In order to develop forest management strategies in
tropical forest in Malaysia, surveying the forest resources and
monitoring the forest area affected by logging activities is essential.
There are tremendous effort has been done in classification of land
cover related to forest resource management in this country as it is a
priority in all aspects of forest mapping using remote sensing and
related technology such as GIS. In fact classification process is a
compulsory step in any remote sensing research. Therefore, the main
objective of this paper is to assess classification accuracy of
classified forest map on Landsat TM data from difference number of
reference data (200 and 388 reference data). This comparison was
made through observation (200 reference data), and interpretation
and observation approaches (388 reference data). Five land cover
classes namely primary forest, logged over forest, water bodies, bare
land and agricultural crop/mixed horticultural can be identified by
the differences in spectral wavelength. Result showed that an overall
accuracy from 200 reference data was 83.5 % (kappa value
0.7502459; kappa variance 0.002871), which was considered
acceptable or good for optical data. However, when 200 reference
data was increased to 388 in the confusion matrix, the accuracy
slightly improved from 83.5% to 89.17%, with Kappa statistic
increased from 0.7502459 to 0.8026135, respectively. The accuracy
in this classification suggested that this strategy for the selection of
training area, interpretation approaches and number of reference data
used were importance to perform better classification result.
Abstract: This paper proposes the use of Bayesian belief
networks (BBN) as a higher level of health risk assessment for a
dumping site of lead battery smelter factory. On the basis of the
epidemiological studies, the actual hospital attendance records and
expert experiences, the BBN is capable of capturing the probabilistic
relationships between the hazardous substances and their adverse
health effects, and accordingly inferring the morbidity of the adverse
health effects. The provision of the morbidity rates of the related
diseases is more informative and can alleviate the drawbacks of
conventional methods.
Abstract: Flow movement in unsaturated soil can be expressed
by a partial differential equation, named Richards equation. The
objective of this study is the finding of an appropriate implicit
numerical solution for head based Richards equation. Some of the
well known finite difference schemes (fully implicit, Crank Nicolson
and Runge-Kutta) have been utilized in this study. In addition, the
effects of different approximations of moisture capacity function,
convergence criteria and time stepping methods were evaluated. Two
different infiltration problems were solved to investigate the
performance of different schemes. These problems include of vertical
water flow in a wet and very dry soils. The numerical solutions of
two problems were compared using four evaluation criteria and the
results of comparisons showed that fully implicit scheme is better
than the other schemes. In addition, utilizing of standard chord slope
method for approximation of moisture capacity function, automatic
time stepping method and difference between two successive
iterations as convergence criterion in the fully implicit scheme can
lead to better and more reliable results for simulation of fluid
movement in different unsaturated soils.
Abstract: The competitive learning is an adaptive process in
which the neurons in a neural network gradually become sensitive to
different input pattern clusters. The basic idea behind the Kohonen-s
Self-Organizing Feature Maps (SOFM) is competitive learning.
SOFM can generate mappings from high-dimensional signal spaces
to lower dimensional topological structures. The main features of this
kind of mappings are topology preserving, feature mappings and
probability distribution approximation of input patterns. To overcome
some limitations of SOFM, e.g., a fixed number of neural units and a
topology of fixed dimensionality, Growing Self-Organizing Neural
Network (GSONN) can be used. GSONN can change its topological
structure during learning. It grows by learning and shrinks by
forgetting. To speed up the training and convergence, a new variant
of GSONN, twin growing cell structures (TGCS) is presented here.
This paper first gives an introduction to competitive learning, SOFM
and its variants. Then, we discuss some GSONN with fixed
dimensionality, which include growing cell structures, its variants
and the author-s model: TGCS. It is ended with some testing results
comparison and conclusions.
Abstract: We constructed a method of phase unwrapping for a typical wave-front by utilizing the maximizer of the posterior marginal (MPM) estimate corresponding to equilibrium statistical mechanics of the three-state Ising model on a square lattice on the basis of an analogy between statistical mechanics and Bayesian inference. We investigated the static properties of an MPM estimate from a phase diagram using Monte Carlo simulation for a typical wave-front with synthetic aperture radar (SAR) interferometry. The simulations clarified that the surface-consistency conditions were useful for extending the phase where the MPM estimate was successful in phase unwrapping with a high degree of accuracy and that introducing prior information into the MPM estimate also made it possible to extend the phase under the constraint of the surface-consistency conditions with a high degree of accuracy. We also found that the MPM estimate could be used to reconstruct the original wave-fronts more smoothly, if we appropriately tuned hyper-parameters corresponding to temperature to utilize fluctuations around the MAP solution. Also, from the viewpoint of statistical mechanics of the Q-Ising model, we found that the MPM estimate was regarded as a method for searching the ground state by utilizing thermal fluctuations under the constraint of the surface-consistency condition.
Abstract: This paper analysed the food security situation among
Nigerian rural farmers. Data collected on 202 rural farmers from
Benue State were analysed using descriptive and inferential statistics.
The study revealed that majority of the respondents (60.83%) had
medium dietary diversity. Furthermore, household daily calorie
requirement for the food secure households was 10,723 and the
household daily calorie consumption was 12,598, with a surplus
index of 0.04. The food security index was 1.16. The Household
daily per capita calorie consumption was 3,221.2. For the food
insecure households, the household daily calorie requirement was
20,213 and the household daily calorie consumption was 17,393. The
shortfall index was 0.14. The food security index was 0.88. The
Household daily per capita calorie consumption was 2,432.8. The
most commonly used coping strategies during food stress included
intercropping (99.2%), reliance on less preferred food (98.1%),
limiting portion size at meal times (85.8%) and crop diversification
(70.8%).
Abstract: Experiments were conducted to characterize fire
properties of wood exposed to the certain external heat flux and
under variety of wood moisture content. Six kinds of Indonesian
wood: keruing, sono, cemara, kamper, pinus, and mahoni were
exposed to radiant heat from a conical heater, result in appearance of
a stable flame on the wood surface caused by spontaneous ignition. A
thermocouple K-type was used to measure the wood surface
temperature. Temperature histories were recorded throughout each
experiment at 1 s intervals using a TC-08. Data of first ignition time
and temperature, end ignition time and temperature, and charring rate
have been successfully collected. It was found that the ignition
temperature and charring rate depend on moisture content of wood.
Abstract: Failure modes and effects analysis (FMEA) is an effective technique for preventing potential problems and actions needed to error cause removal. On the other hand, the oil producing companies paly a critical role in the oil industry of Iran as a developing country out of which, Sepahan Oil Co. has a considerable contribution. The aim of this research is to show how FMEA could be applied and improve the quality of products at Sepahan Oil Co. For this purpose, the four liter production line of the company has been selected for investigation. The findings imply that the application of FMEA has reduced the scraps from 50000 ppm to 5000 ppm and has resulted in a 0.92 percent decrease of the oil waste.
Abstract: Bridges are one of the main components of
transportation networks. They should be functional before and after
earthquake for emergency services. Therefore we need to assess
seismic performance of bridges under different seismic loadings.
Fragility curve is one of the popular tools in seismic evaluations. The
fragility curves are conditional probability statements, which give the
probability of a bridge reaching or exceeding a particular damage
level for a given intensity level. In this study, the seismic
performance of a two-span simply supported concrete bridge is
assessed. Due to usual lack of empirical data, the analytical fragility
curve was developed by results of the dynamic analysis of bridge
subjected to the different time histories in near-fault area.
Abstract: This paper gives an overview of how an OWL
ontology has been created to represent template knowledge models
defined in CML that are provided by CommonKADS.
CommonKADS is a mature knowledge engineering methodology
which proposes the use of template knowledge model for knowledge
modelling. The aim of developing this ontology is to present the
template knowledge model in a knowledge representation language
that can be easily understood and shared in the knowledge
engineering community. Hence OWL is used as it has become a
standard for ontology and also it already has user friendly tools for
viewing and editing.
Abstract: We provide a maximum norm analysis of a finite
element Schwarz alternating method for a nonlinear elliptic boundary
value problem of the form -Δu = f(u), on two overlapping sub
domains with non matching grids. We consider a domain which is
the union of two overlapping sub domains where each sub domain
has its own independently generated grid. The two meshes being
mutually independent on the overlap region, a triangle belonging to
one triangulation does not necessarily belong to the other one. Under
a Lipschitz assumption on the nonlinearity, we establish, on each sub
domain, an optimal L∞ error estimate between the discrete Schwarz
sequence and the exact solution of the boundary value problem.
Abstract: This study investigates the electrical performance of a
planar solid oxide fuel cell unit with cross-flow configuration when the fuel utilization gets higher and the fuel inlet flow are non-uniform.
A software package in this study solves two-dimensional,
simultaneous, partial differential equations of mass, energy, and
electro-chemistry, without considering stack direction variation. The
results show that the fuel utilization increases with a decrease in the molar flow rate, and the average current density decreases when the
molar flow rate drops. In addition, non-uniform Pattern A will induce more severe happening of non-reaction area in the corner of the fuel
exit and the air inlet. This non-reaction area deteriorates the average
current density and then deteriorates the electrical performance to –7%.
Abstract: Information technology managers nowadays are
facing with tremendous pressure to plan, implement, and adopt new
technology solution due to the rapidity of technology changes.
Resulted from a lack of study that have been done in this topic, the
aim of this paper is to provide a comparison review on current tools
that are currently being used in order to respond to technological
changes. The study is based on extensive literature review of
published works with majority of them are ranging from 2000 to the
first part of 2011. The works were gathered from journals, books,
and other information sources available on the Web. Findings show
that, each tools has different focus and none of the tools are
providing a framework in holistic view, which should include
technical, people, process, and business environment aspect. Hence,
this result provides potential information about current available
tools that IT managers could use to manage changes in technology.
Further, the result reveals a research gap in the area where the
industries a short of such framework.
Abstract: A hardware efficient, multi mode, re-configurable
architecture of interleaver/de-interleaver for multiple standards,
like DVB, WiMAX and WLAN is presented. The interleavers
consume a large part of silicon area when implemented by using
conventional methods as they use memories to store permutation
patterns. In addition, different types of interleavers in different
standards cannot share the hardware due to different construction
methodologies. The novelty of the work presented in this paper is
threefold: 1) Mapping of vital types of interleavers including
convolutional interleaver onto a single architecture with flexibility
to change interleaver size; 2) Hardware complexity for channel
interleaving in WiMAX is reduced by using 2-D realization of the
interleaver functions; and 3) Silicon cost overheads reduced by
avoiding the use of small memories. The proposed architecture
consumes 0.18mm2 silicon area for 0.12μm process and can
operate at a frequency of 140 MHz. The reduced complexity helps
in minimizing the memory utilization, and at the same time
provides strong support to on-the-fly computation of permutation
patterns.