Abstract: The large and small-scale shaking table tests, which
was conducted for investigating damage evolution of piles inside
liquefied soil, are numerically simulated and experimental verified by the3D nonlinear finite element analysis. Damage evolution of
elasto-plastic circular steel piles and reinforced concrete (RC) one with cracking and yield of reinforcement are focused on, and the failure patterns and residual damages are captured by the proposed constitutive models. The superstructure excitation behind quay wall is
reproduced as well.
Abstract: Extraction of laccase produced by L. polychrous in an
aqueous two-phase system, composed of polyethylene glycol and
phosphate salt at pH 7.0 and 250C was investigated. The effect of
PEG molecular weight, PEG concentration and phosphate
concentration was determined. Laccase preferentially partitioned to
the top phase. Good extraction of laccase to the top phase was
observed with PEG 4000. The optimum system was found in the
system containing 12% w/w PEG 4000 and 16% w/w phosphate salt
with KE of 88.3, purification factor of 3.0-fold and 99.1% yield.
Some properties of the enzyme such as thermal stability, effect of
heavy metal ions and kinetic constants were also presented in this
work. The thermal stability decreased sharply with high temperature
above 60 0C. The enzyme was inhibited by Cd2+, Pb2+, Zn2+ and
Cu2+. The Vmax and Km values of the enzyme were 74.70
μmol/min/ml and 9.066 mM respectively.
Abstract: In the modern construction practices, industrial wastes
or by-products are largely used as raw materials in cement and
concrete. These impart many benefits to the environment and bringabout
an economic impact because the cost of waste disposal is
constantly increasing due to strict environmental regulations. It was
reported in literature that the leakage of oil onto concrete element in
older cement grinding unit resulted in concrete with greater resistance
to freezing and thawing. This effect was thought to be similar to
adding an air-entraining chemical admixture to concrete. This paper
presents an investigation on the load deflection behaviour and crack
patterns of reinforced concrete (RC) beams subjected to four point
loading. Ten 120x260x1900 mm beams were cast with 100%
ordinary Portland cement (OPC) concrete, 20% fly ash (FA) and 20%
rice husk ash (RHA) blended cement concrete. 0.15% dosage of
admixtures (used engine oil, new engine oil, and superplasticizer)
was used throughout the experiment. Results show that OPC and
OPC/RHA RC beams containing used engine oil and superplasticizer
exhibit higher capacity, 18-26% than their corresponding control
mix.
Abstract: To achieve the desired specifications of gain and
phase margins for plants with time-delay that stabilized with FO-PID
controller a lead compensator is designed. At first the range of
controlled system stability based on stability boundary criteria is
determined. Using stability boundary locus method in frequency
domain the fractional order controller parameters are tuned and then
with drawing bode diagram in frequency domain accessing to desired
gain and phase margin are shown. Numerical examples are given to
illustrate the shapes of the stabilizing region and to show the design
procedure.
Abstract: This research paper is based upon the simulation of
gradient of mathematical functions and scalar fields using MATLAB.
Scalar fields, their gradient, contours and mesh/surfaces are
simulated using different related MATLAB tools and commands for
convenient presentation and understanding. Different mathematical
functions and scalar fields are examined here by taking their
gradient, visualizing results in 3D with different color shadings and
using other necessary relevant commands. In this way the outputs of
required functions help us to analyze and understand in a better way
as compared to just theoretical study of gradient.
Abstract: In July 1, 2007, Taiwan Stock Exchange (TWSE) on
market observation post system (MOPS) adds a new "Financial
reference database" for investors to do investment reference. This
database as a warning to public offering companies listed on the
public financial information and it original within eight targets. In
this paper, this database provided by the indicators for the application
of company financial crisis early warning model verify that the
database provided by the indicator forecast for the financial crisis,
whether or not companies have a high accuracy rate as opposed to
domestic and foreign scholars have positive results. There is use of
Logistic Regression Model application of the financial early warning
model, in which no joined back-conditions is the first model, joined it
in is the second model, has been taken occurred in the financial crisis
of companies to research samples and then business took place
before the financial crisis point with T-1 and T-2 sample data to do
positive analysis. The results show that this database provided the
debt ratio and net per share for the best forecast variables.
Abstract: One astonishing capability of humans is to recognize thousands of different objects visually, and to learn the semantic association between those objects and words referring to them. This work is an attempt to build a computational model of such capacity,simulating the process by which infants learn how to recognize objects and words through exposure to visual stimuli and vocal sounds.One of the main fact shaping the brain of a newborn is that lights and colors come from entities of the world. Gradually the visual system learn which light sensations belong to same entities, despite large changes in appearance. This experience is common between humans and several other mammals, like non-human primates. But humans only can recognize a huge variety of objects, most manufactured by himself, and make use of sounds to identify and categorize them. The aim of this model is to reproduce these processes in a biologically plausible way, by reconstructing the essential hierarchy of cortical circuits on the visual and auditory neural paths.
Abstract: Increasing use of cell phone as a medium of human interaction is playing a vital role in solving riddles of crime as well. A young girl went missing from her home late in the evening in the month of August, 2008 when her enraged relatives and villagers physically assaulted and chased her fiancée who often frequented her home. Two years later, her mother lodged a complaint against the relatives and the villagers alleging that after abduction her daughter was either sold or killed as she had failed to trace her. On investigation, a rusted cell phone with partial visible IMEI number, clothes, bangles, human skeleton etc. recovered from abandoned well in the month of May, 2011 were examined in the lab. All hopes pinned on identity of cell phone, for only linking evidence to fix the scene of occurrence supported by call detail record (CDR) and to dispel doubts about mode of sudden disappearance or death as DNA technology did not help in establishing identity of the deceased. The conventional scientific methods were used without success and international mobile equipment identification number of the cell phone could be generated by using statistical analysis followed by online verification.
Abstract: This paper is concerned with propagation of thermoelastic longitudinal vibrations of an infinite circular cylinder, in the context of the linear theory of generalized thermoelasticity with two relaxation time parameters (Green and Lindsay theory). Three displacement potential functions are introduced to uncouple the equations of motion. The frequency equation, by using the traction free boundary conditions, is given in the form of a determinant involving Bessel functions. The roots of the frequency equation give the value of the characteristic circular frequency as function of the wave number. These roots, which correspond to various modes, are numerically computed and presented graphically for different values of the thermal relaxation times. It is found that the influences of the thermal relaxation times on the amplitudes of the elastic and thermal waves are remarkable. Also, it is shown in this study that the propagation of thermoelastic longitudinal vibrations based on the generalized thermoelasticity can differ significantly compared with the results under the classical formulation. A comparison of the results for the case with no thermal effects shows well agreement with some of the corresponding earlier results.
Abstract: Social cognitive theory explains the power to inaugurate change is determined by the mutual influence of personal proclivity and social factors which will shape ones- motivations and expectations. In construction industry, green concept offers an opportunity to leave a lighter footprint on the environment. This opportunity, however, has not been fully grasped by many countries. As such, venturing into green construction for many practitioners would be their maiden experience. Decision to venture into new practice such as green construction will be influenced by certain drivers. This paper explores these drivers which is further expanded into motivational factors and later becomes the platform upon which expectation for green construction stands. This theoretical concept of motivation and expectations, which is adapted from social cognitive theory, focus on developers- view because of their crucial role in green application. This conceptual framework, which serves as the basis for further research, will benefit the industry as it elucidate cognitive angles to attract more new entrants to green business.
Abstract: In view of geological origin, formation of the shallow
gas reservoir of the Hangzhou Bay, northern Zhejiang Province,
eastern China, and original occurrence characteristics of the gassy
sand are analyzed. Generally, gassy sand in scale gas reservoirs is in
the state of residual moisture content and the approximate scope of
initial matric suction of sand ranges about from 0kPa to100kPa.
Results based on GDS triaxial tests show that the classical shear
strength formulas of unsaturated soil can not effectively describe basic
strength characteristics of gassy sand; the relationship between
apparent cohesion and matric suction of gassy sand agrees well with
the power function, which can reasonably be used to describe the
strength of gassy sand. In the stress path of gas release, shear strength
of gassy sand will increase and experimental results show the formula
proposed in this paper can effectively predict the strength increment.
When saturated strength indexes of the sand are used in engineering
design, moderate reduction should be considered.
Abstract: Solving Ordinary Differential Equations (ODEs) by
using Partitioning Block Intervalwise (PBI) technique is our aim in
this paper. The PBI technique is based on Block Adams Method and
Backward Differentiation Formula (BDF). Block Adams Method
only use the simple iteration for solving while BDF requires Newtonlike
iteration involving Jacobian matrix of ODEs which consumes a
considerable amount of computational effort. Therefore, PBI is
developed in order to reduce the cost of iteration within acceptable
maximum error
Abstract: Pipeline infrastructures normally represent high cost of investment and the pipeline must be free from risks that could cause environmental hazard and potential threats to personnel safety. Pipeline integrity such monitoring and management become very crucial to provide unimpeded transportation and avoiding unnecessary production deferment. Thus proper cleaning and inspection is the key to safe and reliable pipeline operation and plays an important role in pipeline integrity management program and has become a standard industry procedure. In view of this, understanding the motion (dynamic behavior), prediction and control of the PIG speed is important in executing pigging operation as it offers significant benefits, such as estimating PIG arrival time at receiving station, planning for suitable pigging operation, and improves efficiency of pigging tasks. The objective of this paper is to review recent developments in speed control system of pipeline PIGs. The review carried out would serve as an industrial application in a form of quick reference of recent developments in pipeline PIG speed control system, and further initiate others to add-in/update the list in the future leading to knowledge based data, and would attract active interest of others to share their view points.
Abstract: Changing in consumers lifestyles and food
consumption patterns provide a great opportunity in developing the
functional food sector in Malaysia. There is only a little knowledge
about whether Malaysian consumers are aware of functional food and
if so what image consumers have of this product. The objective of
this research is to determine the extent to which selected socioeconomic
characteristics and attitudes influence consumers-
awareness of functional food. A survey was conducted in the Klang
Valley, Malaysia where 439 respondents were interviewed using a
structured questionnaire. The result shows that most respondents
have a positive attitude towards functional food. For the binary
logistic estimation, the results indicate that age, income and other
factors such as concern about food safety, subscribing to cooking or
health magazines, being a vegetarian and consumers who have been
involved in a food production company significantly influence
Malaysian consumers- awareness towards functional food.
Abstract: One of the basic concepts in marketing is the concept
of meeting customers- needs. Since customer satisfaction is essential
for lasting survival and development of a business, screening and
observing customer satisfaction and recognizing its underlying
factors must be one of the key activities of every business.
The purpose of this study is to recognize the drivers that effect
customer satisfaction in a business-to-business situation in order to
improve marketing activities. We conducted a survey in which 93
business customers of a manufacturer of Diesel Generator in Iran
participated and they talked about their ideas and satisfaction of
supplier-s services related to its products. We developed the measures
for drivers of satisfaction first by as investigative research (by means
of feedback from executives and customers of sponsoring firm). Then
based on these measures, we created a mail survey, and asked the
respondents to explain their opinion about the sponsoring firm which
was a supplier of diesel generator and similar products. Furthermore,
the survey required the participants to mention their functional areas
and their company features.
In Conclusion we found that there are three drivers for customer
satisfaction, which are reliability, information about product, and
commercial features. Buyers/users from different functional areas
attribute different degree of importance to the last two drivers. For
instance, people from buying and management areas believe that
commercial features are more important than information about
products. But people in engineering, maintenance and production
areas believe that having information about products is more
important than commercial aspects. Marketing experts should
consider the attribute of customers regarding information about the
product and commercial features to improve market share.
Abstract: This research tries to analyze the role that knowledge
about foreign markets has in increasing firms- exports in clustered
spaces. We consider two interrelated sources of knowledge: firms-
direct experience and indirect experience from other clustered firms –
export externalities. In particular, it is proposed that firms would
improve their export performance by accessing to export externalities
if they have some previous direct experience that allows them to
identify, understand and exploit them. Also, we propose that this
positive influence of previous direct experience on export
externalities keeps only up to a point, where it becomes negative,
creating an inverted “U" shape. Empirical evidence gathered among
wine producers located in La Rioja tends to confirm that firms enjoy
of export externalities if they have export experience along several
years and countries increase their export performance. While this
relationship becomes less relevant as they develop a higher
experience, we could not confirm the existence of a curvilinear
relationship in their influence on export externalities and export
performance.
Abstract: This study evaluates the performance of horizontal
subsurface flow constructed wetland (HSSF-CW) for the removal of
chlorinated resin and fatty acids (RFAs) from pulp and paper mill
wastewater. The dimensions of the treatment system were 3.5 m x 1.5
m x 0.28 m with surface area of 5.25 m2, filled with fine sand and
gravel. The cell was planted with an ornamental plant species Canna
indica. The removal efficiency of chlorinated RFAs was in the range
of 92-96% at the hydraulic retention time (HRT) of 5.9 days. Plant
biomass and soil (sand and gravel) were analyzed for chlorinated
RFAs content. No chlorinated RFAs were detected in plant biomass
but detected in soil samples. Mass balance studies of chlorinated
RFAs in HSSF-CW were also carried out.
Abstract: Computer modeling has played a unique role in
understanding electrocardiography. Modeling and simulating cardiac
action potential propagation is suitable for studying normal and
pathological cardiac activation. This paper presents a 2-D Cellular
Automata model for simulating action potential propagation in
cardiac tissue. We demonstrate a novel algorithm in order to use
minimum neighbors. This algorithm uses the summation of the
excitability attributes of excited neighboring cells. We try to
eliminate flat edges in the result patterns by inserting probability to
the model. We also preserve the real shape of action potential by
using linear curve fitting of one well known electrophysiological
model.
Abstract: Shape optimization of the airfoil with high aspect ratio
of long endurance unmanned aerial vehicle (UAV) is performed by the
multi-objective optimization technology coupled with computational
fluid dynamics (CFD). For predicting the aerodynamic characteristics
around the airfoil the high-fidelity Navier-Stokes solver is employed
and SMOGA (Simple Multi-Objective Genetic Algorithm), which is
developed by authors, is used for solving the multi-objective
optimization problem. To obtain the optimal solutions of the design
variable (i.e., sectional airfoil profile, wing taper ratio and sweep) for
high performance of UAVs, both the lift and lift-to-drag ratio are
maximized whereas the pitching moment should be minimized,
simultaneously. It is found that the lift force and lift-to-drag ratio are
linearly dependent and a unique and dominant solution are existed.
However, a trade-off phenomenon is observed between the lift-to-drag
ratio and pitching moment. As the result of optimization, sixty-five
(65) non-dominated Pareto individuals at the cutting edge of design
spaces that is decided by airfoil shapes can be obtained.
Abstract: The communication networks development and
advancement during two last decades has been toward a single goal
and that is gradual change from circuit-switched networks to packed
switched ones. Today a lot of networks operates are trying to
transform the public telephone networks to multipurpose packed
switch. This new achievement is generally called "next generation
networks". In fact, the next generation networks enable the operators
to transfer every kind of services (sound, data and video) on a
network. First, in this report the definition, characteristics and next
generation networks services and then ad-hoc networks role in the
next generation networks are studied.