Abstract: This study presents a simulation model for converting coal to methanol, based on gasification technology with the commercial chemical process simulator, Pro/II® V8.1.1. The methanol plant consists of air separation unit (ASU), gasification unit, gas clean-up unit, and methanol synthetic unit. The clean syngas is produced with the first three operating units, and the model has been verified with the reference data from United States Environment Protection Agency. The liquid phase methanol (LPMEOHTM) process is adopted in the methanol synthetic unit. Clean syngas goes through gas handing section to reach the reaction requirement, reactor loop/catalyst to generate methanol, and methanol distillation to get desired purity over 99.9 wt%. The ratio of the total energy combined with methanol and dimethyl ether to that of feed coal is 78.5% (gross efficiency). The net efficiency is 64.2% with the internal power consumption taken into account, based on the assumption that the efficiency of electricity generation is 40%.
Abstract: A mathematical model based on a mass and energy
balance for the combustion in a cement rotary kiln was developed.
The model was used to investigate the impact of replacing about
45 % of the primary coal energy by different alternative fuels.
Refuse derived fuel, waste wood, solid hazardous waste and liquid
hazardous waste were used in the modeling. The results showed that
in order to keep the kiln temperature unchanged, and thereby
maintain the required clinker quality, the production capacity had to
be reduced by 1-15 %, depending on the fuel type. The reason for the
reduction is increased exhaust gas flow rates caused by the fuel
characteristics. The model, which has been successfully validated in a
full-scale experiment, was also used to show that the negative impact
on the production capacity can be avoided if a relatively small part of
the combustion air is replaced by pure oxygen.
Abstract: Nowaday-s, many organizations use systems that
support business process as a whole or partially. However, in some
application domains, like software development and health care
processes, a normative Process Aware System (PAS) is not suitable,
because a flexible support is needed to respond rapidly to new
process models. On the other hand, a flexible Process Aware System
may be vulnerable to undesirable and fraudulent executions, which
imposes a tradeoff between flexibility and security. In order to make
this tradeoff available, a genetic-based anomaly detection model for
logs of Process Aware Systems is presented in this paper. The
detection of an anomalous trace is based on discovering an
appropriate process model by using genetic process mining and
detecting traces that do not fit the appropriate model as anomalous
trace; therefore, when used in PAS, this model is an automated
solution that can support coexistence of flexibility and security.
Abstract: For about two decades scientists have been
developing techniques for enhancing the quality of medical images
using Fourier transform, DWT (Discrete wavelet transform),PDE
model etc., Gabor wavelet on hexagonal sampled grid of the images
is proposed in this work. This method has optimal approximation
theoretic performances, for a good quality image. The computational
cost is considerably low when compared to similar processing in the
rectangular domain. As X-ray images contain light scattered pixels,
instead of unique sigma, the parameter sigma of 0.5 to 3 is found to
satisfy most of the image interpolation requirements in terms of high
Peak Signal-to-Noise Ratio (PSNR) , lower Mean Squared Error
(MSE) and better image quality by adopting windowing technique.
Abstract: Multimedia security is an incredibly significant area of concern. The paper aims to discuss a robust image watermarking scheme, which can withstand geometric attacks. The source image is initially moment normalized in order to make it withstand geometric attacks. The moment normalized image is wavelet transformed. The first level wavelet transformed image is segmented into blocks if size 8x8. The product of mean and standard and standard deviation of each block is computed. The second level wavelet transformed image is divided into 8x8 blocks. The product of block mean and the standard deviation are computed. The difference between products in the two levels forms the watermark. The watermark is inserted by modulating the coefficients of the mid frequencies. The modulated image is inverse wavelet transformed and inverse moment normalized to generate the watermarked image. The watermarked image is now ready for transmission. The proposed scheme can be used to validate identification cards and financial instruments. The performance of this scheme has been evaluated using a set of parameters. Experimental results show the effectiveness of this scheme.
Abstract: This study deals with a multi-criteria optimization
problem which has been transformed into a single objective
optimization problem using Response Surface Methodology (RSM),
Artificial Neural Network (ANN) and Grey Relational Analyses
(GRA) approach. Grey-RSM and Grey-ANN are hybrid techniques
which can be used for solving multi-criteria optimization problem.
There have been two main purposes of this research as follows.
1. To determine optimum and robust fiber dyeing process
conditions by using RSM and ANN based on GRA,
2. To obtain the best suitable model by comparing models
developed by different methodologies.
The design variables for fiber dyeing process in textile are
temperature, time, softener, anti-static, material quantity, pH,
retarder, and dispergator. The quality characteristics to be evaluated
are nominal color consistency of fiber, maximum strength of fiber,
minimum color of dyeing solution. GRA-RSM with exact level
value, GRA-RSM with interval level value and GRA-ANN models
were compared based on GRA output value and MSE (Mean Square
Error) performance measurement of outputs with each other. As a
result, GRA-ANN with interval value model seems to be suitable
reducing the variation of dyeing process for GRA output value of the
model.
Abstract: This paper explores the implementation of adaptive
coding and modulation schemes for Multiple-Input Multiple-Output
Orthogonal Frequency Division Multiplexing (MIMO-OFDM) feedback
systems. Adaptive coding and modulation enables robust and
spectrally-efficient transmission over time-varying channels. The basic
premise is to estimate the channel at the receiver and feed this estimate
back to the transmitter, so that the transmission scheme can be
adapted relative to the channel characteristics. Two types of codebook
based channel feedback techniques are used in this work. The longterm
and short-term CSI at the transmitter is used for efficient channel
utilization. OFDM is a powerful technique employed in communication
systems suffering from frequency selectivity. Combined with
multiple antennas at the transmitter and receiver, OFDM proves to be
robust against delay spread. Moreover, it leads to significant data rates
with improved bit error performance over links having only a single
antenna at both the transmitter and receiver. The coded modulation
increases the effective transmit power relative to uncoded variablerate
variable-power MQAM performance for MIMO-OFDM feedback
system. Hence proposed arrangement becomes an attractive approach
to achieve enhanced spectral efficiency and improved error rate
performance for next generation high speed wireless communication
systems.
Abstract: Since IEC61850 substation communication standard represents the trend to develop new generations of Substation Automation System (SAS), many IED manufacturers pursue this technique and apply for KEMA. In order to put on the market to meet customer demand as fast as possible, manufacturers often apply their products only for basic environment standard certification but claim to conform to IEC61850 certification. Since verification institutes generally perform verification tests only on specific IEDs of the manufacturers, the interoperability between all certified IEDs cannot be guaranteed. Therefore the interoperability between IEDs from different manufacturers needs to be tested. Based upon the above reasons, this study applies the definitions of the information models, communication service, GOOSE functionality and Substation Configuration Language (SCL) of the IEC61850 to build the concept of communication protocols, and build the test environment. The procedures of the test of the data collection and exchange of the P2P communication mode and Client / Server communication mode in IEC61850 are outlined as follows. First, test the IED GOOSE messages communication capability from different manufacturers. Second, collect IED data from each IED with SCADA system and use HMI to display the SCADA platform. Finally, problems generally encountered in the test procedure are summarized.
Abstract: In this paper we present a Feed-Foward Neural
Networks Autoregressive (FFNN-AR) model with genetic algorithms
training optimization in order to predict the gross domestic product
growth of six countries. Specifically we propose a kind of weighted
regression, which can be used for econometric purposes, where the
initial inputs are multiplied by the neural networks final optimum
weights from input-hidden layer of the training process. The
forecasts are compared with those of the ordinary autoregressive
model and we conclude that the proposed regression-s forecasting
results outperform significant those of autoregressive model.
Moreover this technique can be used in Autoregressive-Moving
Average models, with and without exogenous inputs, as also the
training process with genetics algorithms optimization can be
replaced by the error back-propagation algorithm.
Abstract: Embedding Sustainability in technological curricula has become a crucial factor for educating engineers with competences in sustainability. The Technical University of Catalonia UPC, in 2008, designed the Sustainable Technology Excellence Program STEP 2015 in order to assure a successful Sustainability Embedding. This Program takes advantage of the opportunity that the redesign of all Bachelor and Master Degrees in Spain by 2010 under the European Higher Education Area framework offered. The STEP program goals are: to design compulsory courses in each degree; to develop the conceptual base and identify reference models in sustainability for all specialties at UPC; to create an internal interdisciplinary network of faculty from all the schools; to initiate new transdisciplinary research activities in technology-sustainability-education; to spread the know/how attained; to achieve international scientific excellence in technology-sustainability-education and to graduate the first engineers/architects of the new EHEA bachelors with sustainability as a generic competence. Specifically, in this paper authors explain their experience in leading the STEP program, and two examples are presented: Industrial Robotics subject and the curriculum for the School of Architecture.
Abstract: Many real-world data sets consist of a very high dimensional feature space. Most clustering techniques use the distance or similarity between objects as a measure to build clusters. But in high dimensional spaces, distances between points become relatively uniform. In such cases, density based approaches may give better results. Subspace Clustering algorithms automatically identify lower dimensional subspaces of the higher dimensional feature space in which clusters exist. In this paper, we propose a new clustering algorithm, ISC – Intelligent Subspace Clustering, which tries to overcome three major limitations of the existing state-of-art techniques. ISC determines the input parameter such as є – distance at various levels of Subspace Clustering which helps in finding meaningful clusters. The uniform parameters approach is not suitable for different kind of databases. ISC implements dynamic and adaptive determination of Meaningful clustering parameters based on hierarchical filtering approach. Third and most important feature of ISC is the ability of incremental learning and dynamic inclusion and exclusions of subspaces which lead to better cluster formation.
Abstract: The noteworthy point in the advancement of Brain Machine Interface (BMI) research is the ability to accurately extract features of the brain signals and to classify them into targeted control action with the easiest procedures since the expected beneficiaries are of disabled. In this paper, a new feature extraction method using the combination of adaptive band pass filters and adaptive autoregressive (AAR) modelling is proposed and applied to the classification of right and left motor imagery signals extracted from the brain. The introduction of the adaptive bandpass filter improves the characterization process of the autocorrelation functions of the AAR models, as it enhances and strengthens the EEG signal, which is noisy and stochastic in nature. The experimental results on the Graz BCI data set have shown that by implementing the proposed feature extraction method, a LDA and SVM classifier outperforms other AAR approaches of the BCI 2003 competition in terms of the mutual information, the competition criterion, or misclassification rate.
Abstract: Restoration of endodontically treated teeth is a
common problem in dentistry, related to the fractures occurring in
such teeth and to concentration of forces little information regarding
variation of basic preparation guidelines in stress distribution has
been available. To date, there is still no agreement in the literature
about which material or technique can optimally restore
endodontically treated teeth. The aim of the present study was to
evaluate the influence of the core height and restoration materials on
corono-radicular restored upper first premolar. The first step of the
study was to achieve 3D models in order to analyze teeth, dowel and
core restorations and overlying full ceramic crowns. The FEM model
was obtained by importing the solid model into ANSYS finite
element analysis software. An occlusal load of 100 N was conducted,
and stresses occurring in the restorations, and teeth structures were
calculated. Numerical simulations provide a biomechanical
explanation for stress distribution in prosthetic restored teeth. Within
the limitations of the present study, it was found that the core height
has no important influence on the stress generated in coronoradicular
restored premolars. It can be drawn that the cervical regions
of the teeth and restorations were subjected to the highest stress
concentrations.
Abstract: The myoelectric signal (MES) is one of the Biosignals
utilized in helping humans to control equipments. Recent approaches
in MES classification to control prosthetic devices employing pattern
recognition techniques revealed two problems, first, the classification
performance of the system starts degrading when the number of
motion classes to be classified increases, second, in order to solve the
first problem, additional complicated methods were utilized which
increase the computational cost of a multifunction myoelectric
control system. In an effort to solve these problems and to achieve a
feasible design for real time implementation with high overall
accuracy, this paper presents a new method for feature extraction in
MES recognition systems. The method works by extracting features
using Wavelet Packet Transform (WPT) applied on the MES from
multiple channels, and then employs Fuzzy c-means (FCM)
algorithm to generate a measure that judges on features suitability for
classification. Finally, Principle Component Analysis (PCA) is
utilized to reduce the size of the data before computing the
classification accuracy with a multilayer perceptron neural network.
The proposed system produces powerful classification results (99%
accuracy) by using only a small portion of the original feature set.
Abstract: The history of money is described in relationship to the history of computing. With the transformation and acceptance of money as information, major challenges to the security of money have involved engineering, computer science, and management. Research opportunities and challenges are described as money continues its transformation into information.
Abstract: This paper discusses a systematic design of a Σ-Δ fractional-N Phase-Locked Loop based on HDL behavioral modeling. The proposed design consists in describing the mixed behavior of this PLL architecture starting from the specifications of each building block. The HDL models of critical PLL blocks have been described in VHDL-AMS to predict the different specifications of the PLL. The effect of different noise sources has been efficiently introduced to study the PLL system performances. The obtained results are compared with transistor-level simulations to validate the effectiveness of the proposed models for wireless applications in the frequency range around 2.45 GHz.
Abstract: Article 5(3) of the Brussels I Regulation provides that a person domiciled in a Member State may be sued in another Member State in matters relating to tort, delict or quasi-delict, in the courts for the place where the harmful events occurred or may occur. For a number of years Article 5 (3) of the Brussels I Regulation has been at the centre of the debate regarding the intellectual property rights infringement over the Internet. Nothing has been done to adapt the provisions relating to non-internet cases of infringement of intellectual property rights to the context of the Internet. The author’s findings indicate that in the case of intellectual property rights infringement on the Internet, the plaintiff has the option to sue either: the court of the Member State of the event giving rise to the damage: where the publisher of the newspaper is established; the court of the Member State where the damage occurred: where defamatory article is distributed. However, it must be admitted that whilst infringement over the Internet has some similarity to multi-State defamation by means of newspapers, the position is not entirely analogous due to the cross-border nature of the Internet. A simple example which may appropriately illustrate its contentious nature is a defamatory statement published on a website accessible in different Member States, and available in different languages. Therefore, we need to answer the question: how these traditional jurisdictional rules apply in the case of intellectual property rights infringement over the Internet? Should these traditional jurisdictional rules be modified?
Abstract: This study1 holds for the formation of international financial crisis and political factors for economic crisis in Turkey, are evaluated in chronological order. The international arena and relevant studies conducted in Turkey work in the literature are assessed. The main purpose of the study is to hold the linkage between the crises and political stability in Turkey in details, and to examine the position of Turkey in this regard. The introduction part follows the literature survey on the models explaining causes and results of the crises, the second part of the study. In the third part, the formations of the world financial crises are studied. The fourth part, financial crisis in Turkey in 1994, 2000, 2001 and 2008 are reviewed and their political reasons are analyzed. In the last part of the study the results and recommendations are held. Political administrations have laid the grounds for an economic crisis in Turkey. In this study, the emergence of an economic crisis in Turkey and the developments after the crisis are chronologically examined and an explanation is offered as to the cause and effect relationship between the political administration and economic equilibrium in the country. Economic crises can be characterized as follows: high prices of consumables, high interest rates, current account deficits, budget deficits, structural defects in government finance, rising inflation and fixed currency applications, rising government debt, declining savings rates and increased dependency on foreign capital stock. Entering into the conditions of crisis during a time when the exchange value of the country-s national currency was rising, speculative finance movements and shrinking of foreign currency reserves happened due to expectations for devaluation and because of foreign investors- resistance to financing national debt, and a financial risk occurs. During the February 2001 crisis and immediately following, devaluation and reduction of value occurred in Turkey-s stock market. While changing over to the system of floating exchange rates in the midst of this crisis, the effects of the crisis on the real economy are discussed in this study. Administered politics include financial reforms, such as the rearrangement of banking systems. These reforms followed with the provision of foreign financial support. There have been winners and losers in the imbalance of income distribution, which has recently become more evident in Turkey-s fragile economy.
Abstract: To make use of the limited amounts of water in arid
region, the Iranians developed man-made underground water
channels called qanats (kanats) .In fact, qanats may be considered as
the first long-distance water transfer system. Qanats are an ancient
water transfer system found in arid regions wherein groundwater
from mountainous areas, aquifers and sometimes from rivers, was
brought to points of re-emergence such as an oasis, through one or
more underground tunnels. The tunnels, many of which were
kilometers in length, had designed for slopes to provide gravitational
flow. The tunnels allowed water to drain out to the surface by gravity
to supply water to lower and flatter agricultural land.
Qanats have been an ancient, sustainable system facilitating the
harvesting of water for centuries in Iran, and more than 35 additional
countries of the world such as India, Arabia, Egypt, North Africa,
Spain and even to New world.
There are about 22000 qanats in Iran with 274000 kilometers of
underground conduits all built by manual labor. The amount of
water of the usable qanats of Iran produce is altogether 750 to
1000 cubic meter per second. The longest chain of qanat is
situated in Gonabad region in Khorasan province. It is 70
kilometers long. Qanats are renewable water supply systems that
have sustained agricultural settlement on the Iranian plateau for
millennia. The great advantages of Qanats are no evaporation
during transit, little seepage , no raising of the water- table and no
pollution in the area surrounding the conduits. Qanat systems
have a profound influence on the lives of the water users in Iran, and
conform to Iran-s climate. Qanat allows those living in a desert
environment adjacent to a mountain watershed to create a large oasis
in an otherwise stark environment.
This paper explains qanats structure designs, their history,
objectives causing their creation, construction materials, locations
and their importance in different times, as well as their present
sustainable role in Iran.
Abstract: The environmental impacts caused by the current production and consumption models, together with the impact that the current economic crisis, bring necessary changes in the European industry toward new business models based on sustainability issues that could allow them to innovate and improve their competitiveness. This paper analyzes the key environmental issues and the current and future market trends in one of the most important industrial sectors in Spain, the furniture sector. It also proposes new decision support tools -diagnostic kit, roadmap and guidelines- to guide companies to implement sustainability criteria into their organizations, including eco-design strategies and other economical and social strategies in accordance with the sustainability definition, and other available tools such as eco-labels, environmental management systems, etc., and to use and combine them to obtain the results the company expects to help improve its competitiveness.