Abstract: In order to utilize results from global climate models,
dynamical and statistical downscaling techniques have been
developed. For dynamical downscaling, usually a limited area
numerical model is used, with associated high computational cost.
This research proposes dynamic equation for specific space-time
regional climate downscaling from the Educational Global Climate
Model (EdGCM) for Southeast Asia. The equation is for surface air
temperature. This equation provides downscaling values of surface
air temperature at any specific location and time without running a
regional climate model. In the proposed equations, surface air
temperature is approximated from ground temperature, sensible heat
flux and 2m wind speed. Results from the application of the equation
show that the errors from the proposed equations are less than the
errors for direct interpolation from EdGCM.
Abstract: Wind energy is rapidly emerging as the primary
source of electricity in the Philippines, although developing an
accurate wind resource model is difficult. In this study, Weather
Research and Forecasting (WRF) Model, an open source mesoscale
Numerical Weather Prediction (NWP) model, was used to produce a
1-year atmospheric simulation with 4 km resolution on the Ilocos
Region of the Philippines. The WRF output (netCDF) extracts the
annual mean wind speed data using a Python-based Graphical User
Interface. Lastly, wind resource assessment was produced using a
GIS software. Results of the study showed that it is more flexible to
use Python scripts than using other post-processing tools in dealing
with netCDF files. Using WRF Model, Python, and Geographic
Information Systems, a reliable wind resource map is produced.
Abstract: Lagos urban mini bus drivers play a critical role in the
transportation sector. The current major mode of transportation
within Lagos metropolis remains road transportation and this
confirms the relevance of urban mini-bus drivers in transporting the
populace to their various destinations. Other modes of transportation
such as the train and waterways are currently inadequate. Various
threats to the well-being of urban bus drivers include congested
traffic typical of modern day lifestyles, dwindling financial returns
due to long hours in traffic, fewer hours of sleep, inadequate diet,
time pressure, and assaults related to fare disputes. Several healthrelated
problems have been documented to be associated with urban
bus driving. For instance, greater rates of hypertension, obesity and
cholesterol level have been reported. Research studies are yet to
identify the influence of age and marital status on the well-being of
urban mini-bus drivers in Lagos metropolis. A study of this nature is
necessary as it is culturally perceived in Nigeria that older and
married people are especially influenced by family affiliation and
would behave in ways that would project positive outcomes. The
study sample consisted of 150 urban mini-bus drivers who were
conveniently sampled from six (6) different terminuses where their
journey begins and terminates. The well-being questionnaire was
administered to participants. The criteria for inclusion in the study
included the ability to read in English language and the confirmation
that interested participants were on duty and suited to be driving
mini-buses. Due to the nature of the job of bus driving, the researcher
administered the questionnaires on participants who were free and
willing to respond to the survey. All participants were males of
various age groups and of different marital statuses. Results of
analyses conducted revealed no significant influence of age and
marital status on the well-being of urban mini-bus drivers. This
indicates that the well-being of urban mini bus drivers is not
influenced by age or marital status. The findings of this study have
cultural implications. It negates the popularly held belief that older
and married people care more about their well-being than younger
and single people. It brings to fore the need to also identify and
consider other factors when certifying people for the job of urban bus
driving.
Abstract: A solar receiver is designed for operation under
extremely uneven heat flux distribution, cyclic weather, and cloud
transient cycle conditions, which can include large thermal stress and
even receiver failure. In this study, the effect of different oil velocity
on convection coefficient factor and impact of wind velocity on local
Nusselt number by Finite Volume Method will be analyzed. This
study is organized to give an overview of the numerical modeling
using a MATLAB software, as an accurate, time efficient and
economical way of analyzing the heat transfer trends over stationary
receiver tube for different Reynolds number. The results reveal when
oil velocity is below 0.33m/s, the value of convection coefficient is
negligible at low temperature. The numerical graphs indicate that
when oil velocity increases up to 1.2 m/s, heat convection coefficient
increases significantly. In fact, a reduction in oil velocity causes a
reduction in heat conduction through the glass envelope. In addition,
the different local Nusselt number is reduced when the wind blows
toward the concave side of the collector and it has a significant effect
on heat losses reduction through the glass envelope.
Abstract: Sweep frequency response analysis has been turning
out a powerful tool for investigation of mechanical as well as
electrical integration of transformers. In this paper various aspect of
practical application of SFRA has been studied. Open circuit and
short circuit measurement were done on different phases of high
voltage and low voltage winding. A case study was presented for the
transformer of rating 31.5 MVA for various frequency ranges. A
clear picture was presented for sub- frequency ranges for HV as well
as LV winding. The main motive of work is to investigate high
voltage short circuit response. The theoretical concept about SFRA
responses is validated with expert system software results.
Abstract: Large-scale machine tools for the manufacturing of
large work pieces, e.g. blades, casings or gears for wind turbines,
feature pose-dependent dynamic behavior. Small structural damping
coefficients lead to long decay times for structural vibrations that
have negative impacts on the production process. Typically, these
vibrations are handled by increasing the stiffness of the structure by
adding mass. This is counterproductive to the needs of sustainable
manufacturing as it leads to higher resource consumption both in
material and in energy. Recent research activities have led to higher
resource efficiency by radical mass reduction that is based on controlintegrated
active vibration avoidance and damping methods. These
control methods depend on information describing the dynamic
behavior of the controlled machine tools in order to tune the
avoidance or reduction method parameters according to the current
state of the machine. This paper presents the appearance, consequences and challenges
of the pose-dependent dynamic behavior of lightweight large-scale
machine tool structures in production. It starts with the theoretical
introduction of the challenges of lightweight machine tool structures
resulting from reduced stiffness. The statement of the pose-dependent
dynamic behavior is corroborated by the results of the experimental
modal analysis of a lightweight test structure. Afterwards, the
consequences of the pose-dependent dynamic behavior of lightweight
machine tool structures for the use of active control and vibration
reduction methods are explained. Based on the state of the art of
pose-dependent dynamic machine tool models and the modal
investigation of an FE-model of the lightweight test structure, the
criteria for a pose-dependent model for use in vibration reduction are
derived. The description of the approach for a general posedependent
model of the dynamic behavior of large lightweight
machine tools that provides the necessary input to the aforementioned
vibration avoidance and reduction methods to properly tackle
machine vibrations is the outlook of the paper.
Abstract: Novel wind-lens turbine designs can augment power
output. Vacuum-Assisted Resin Transfer Molding (VARTM) is used
to form large and complex structures from a Carbon Fiber Reinforced
Polymer (CFRP) composite. Typically, wind-lens turbine structures
are fabricated in segments, and then bonded to form the final structure.
This paper introduces five new adhesive joints, divided into two
groups: one is constructed between dry carbon and CFRP fabrics, and
the other is constructed with two dry carbon fibers. All joints and
CFRP fabrics were made in our laboratory using VARTM
manufacturing techniques. Specimens were prepared for tensile testing
to measure joint performance. The results showed that the second
group of joints achieved a higher tensile strength than the first group.
On the other hand, the tensile fracture behavior of the two groups
showed the same pattern of crack originating near the joint ends
followed by crack propagation until fracture.
Abstract: The paper aims at investigating the effect of number
of story on different structural components of reinforced concrete
building due to gravity and lateral loading. For the study, three
building models having same building plan of three, six and nine
stories are analyzed and designed using software package. All the
buildings are residential and are located in Dhaka city of Bangladesh.
Lateral load including wind and earthquake loading are applied to the
building along both longitudinal and transverse direction as per
Bangladesh National Building Code (BNBC, 2006). Equivalent static
force method is followed for the applied seismic loading. The present
study investigates as well as compares mainly total steel requirement
in different structural components for those buildings. It has been
found that total longitudinal steel requirement for beams at each floor
is 48.57% for three storied building, 61.36% for six storied building
when the total percentage is taken as 100% in case of nine storied
building. For an exterior column, the steel ratio is 2.1%, 3.06%,
4.55% for three, six and nine storied building respectively for the first
three floors. In addition, it has been noted that total weight of
longitudinal reinforcement of an interior column is 14.02 % for threestoried
building and 43.12% for six storied building when the total
reinforcement is considered 100% for nine storied building for the
first three floors.
Abstract: The use of wireless technology in industrial networks
has gained vast attraction in recent years. In this paper, we have
thoroughly analyzed the effect of contention window (CW) size on
the performance of IEEE 802.11-based industrial wireless networks
(IWN), from delay and reliability perspective. Results show that the
default values of CWmin, CWmax, and retry limit (RL) are far from
the optimum performance due to the industrial application
characteristics, including short packet and noisy environment. In this
paper, an adaptive CW algorithm (payload-dependent) has been
proposed to minimize the average delay. Finally a simple, but
effective CW and RL setting has been proposed for industrial
applications which outperforms the minimum-average-delay solution
from maximum delay and jitter perspective, at the cost of a little
higher average delay. Simulation results show an improvement of up
to 20%, 25%, and 30% in average delay, maximum delay and jitter
respectively.
Abstract: Carbon Fiber Reinforced Plastics (CFRPs) are widely
used for advanced applications, in particular in aerospace, automotive
and wind energy industries. Once cured to near net shape, CFRP
parts need several finishing operations such as trimming, milling or
drilling in order to accommodate fastening hardware and meeting the
final dimensions. The present research aims to study the effect of the
cutting temperature in trimming on the mechanical strength of high
performance CFRP laminates used for aeronautics applications. The
cutting temperature is of great importance when dealing with
trimming of CFRP. Temperatures higher than the glass-transition
temperature (Tg) of the resin matrix are highly undesirable: they
cause degradation of the matrix in the trimmed edges area, which can
severely affect the mechanical performance of the entire component.
In this study, a 9.50mm diameter CVD diamond coated carbide tool
with six flutes was used to trim 24-plies CFRP laminates. A
300m/min cutting speed and 1140mm/min feed rate were used in the
experiments. The tool was heated prior to trimming using a
blowtorch, for temperatures ranging from 20°C to 300°C. The
temperature at the cutting edge was measured using embedded KType
thermocouples. Samples trimmed for different cutting
temperatures, below and above Tg, were mechanically tested using
three-points bending short-beam loading configurations. New cutting
tools as well as worn cutting tools were utilized for the experiments.
The experiments with the new tools could not prove any correlation
between the length of cut, the cutting temperature and the mechanical
performance. Thus mechanical strength was constant, regardless of
the cutting temperature. However, for worn tools, producing a cutting
temperature rising up to 450°C, thermal damage of the resin was
observed. The mechanical tests showed a reduced mean resistance in
short beam configuration, while the resistance in three point bending
decreases with increase of the cutting temperature.
Abstract: This paper presents a grid synchronization technique based on adaptive notch filter for SPV (Solar Photovoltaic) system along with MPPT (Maximum Power Point Tracking) techniques. An efficient grid synchronization technique offers proficient detection of various components of grid signal like phase and frequency. It also acts as a barrier for harmonics and other disturbances in grid signal. A reference phase signal synchronized with the grid voltage is provided by the grid synchronization technique to standardize the system with grid codes and power quality standards. Hence, grid synchronization unit plays important role for grid connected SPV systems. As the output of the PV array is fluctuating in nature with the meteorological parameters like irradiance, temperature, wind etc. In order to maintain a constant DC voltage at VSC (Voltage Source Converter) input, MPPT control is required to track the maximum power point from PV array. In this work, a variable step size P & O (Perturb and Observe) MPPT technique with DC/DC boost converter has been used at first stage of the system. This algorithm divides the dPpv/dVpv curve of PV panel into three separate zones i.e. zone 0, zone 1 and zone 2. A fine value of tracking step size is used in zone 0 while zone 1 and zone 2 requires a large value of step size in order to obtain a high tracking speed. Further, adaptive notch filter based control technique is proposed for VSC in PV generation system. Adaptive notch filter (ANF) approach is used to synchronize the interfaced PV system with grid to maintain the amplitude, phase and frequency parameters as well as power quality improvement. This technique offers the compensation of harmonics current and reactive power with both linear and nonlinear loads. To maintain constant DC link voltage a PI controller is also implemented and presented in this paper. The complete system has been designed, developed and simulated using SimPower System and Simulink toolbox of MATLAB. The performance analysis of three phase grid connected solar photovoltaic system has been carried out on the basis of various parameters like PV output power, PV voltage, PV current, DC link voltage, PCC (Point of Common Coupling) voltage, grid voltage, grid current, voltage source converter current, power supplied by the voltage source converter etc. The results obtained from the proposed system are found satisfactory.
Abstract: This paper presents the results of a Finite Element
based vibration analysis of a solar powered Unmanned Aerial
Vehicle (UAV). The purpose of this paper was to quantify the free
vibration, forced vibration response due to differing point inputs in
order to predict the relative response magnitudes and frequencies at
various wing locations of vibration induced power generators
(magnet in coil) excited by gust and/or control surface pulse-decays
used to help power the flight of the electric UAV. A Fluid Structure
Interaction (FSI) study was performed in order to ascertain pertinent
design stresses and deflections as well as aerodynamic parameters of
the UAV airfoil. The 10 ft span airfoil is modeled using Mylar as the
primary material. Results show that the free mode in bending is 4.8
Hz while the first forced bending mode is on range of 16.2 to 16.7 Hz
depending on the location of excitation. The free torsional bending
mode is 28.3 Hz, and the first forced torsional mode is range of 26.4
to 27.8 Hz, depending on the location of excitation. The FSI results
predict the coefficients of aerodynamic drag and lift of 0.0052 and
0.077, respectively, which matches hand-calculations used to validate
the Finite Element based results. FSI based maximum von Mises
stresses and deflections were found to be 0.282 MPa and 3.4 mm,
respectively. Dynamic pressures on the airfoil range from 1.04 to
1.23 kPa corresponding to velocity magnitudes in range of 22 to 66
m/s.
Abstract: A novel Active Flap System (AFS) has been developed
at DTU Wind Energy, as a result of a 3-year R&D project following
almost 10 years of innovative research in this field. The full scale AFS
comprises an active deformable trailing edge has been tested at the
unique rotating test facility at the Risø Campus of DTU Wind Energy
in Denmark. The design and instrumentation of the wing section and
the AFS are described. The general description and objectives of the
rotating test rig at the Risø campus of DTU are presented, along
with an overview of sensors on the setup and the test cases. The
post-processing of data is discussed and results of steady, flap step
and azimuth control flap cases are presented.
Abstract: Due to the interference effects, the intrinsic
aerodynamic parameters obtained from the individual component
testing are always fundamentally different than those obtained for
complete model testing. Consideration and limitation for such testing
need to be taken into account in any design work related to the
component buildup method. In this paper, the scaled model of a
straight rectangular canard of a hybrid buoyant aircraft is tested at 50
m/s in IIUM-LSWT (Low Speed Wind Tunnel). Model and its
attachment with the balance are kept rigid to have results free from
the aeroelastic distortion. Based on the velocity profile of the test
section’s floor; the height of the model is kept equal to the
corresponding boundary layer displacement. Balance measurements
provide valuable but limited information of overall aerodynamic
behavior of the model. Zero lift coefficient is obtained at -2.2o and
the corresponding drag coefficient was found to be less than that at
zero angle of attack. As a part of the validation of low fidelity tool,
plot of lift coefficient plot was verified by the experimental data and
except the value of zero lift coefficients, the overall trend has under
predicted the lift coefficient. Based on this comparative study, a
correction factor of 1.36 is proposed for lift curve slope obtained
from the panel method.
Abstract: We report the design and characterization of ultra high
quality factor filter based on one-dimensional photonic-crystal Thue-
Morse sequence structure. The behavior of aperiodic array of
photonic crystal structure is numerically investigated and we show
that by changing the angle of incident wave, desired wavelengths
could be tuned and a tunable filter is realized. Also it is shown that
high quality factor filter be achieved in the telecommunication
window around 1550 nm, with a device based on Thue-Morse
structure. Simulation results show that the proposed structure has a
quality factor more than 100000 and it is suitable for DWDM
communication applications.
Abstract: This paper investigates the thermal issue of permanent
magnet synchronous generator which is frequently used in direct
drive gearless small-scale wind turbine applications. Permanent
Magnet Synchronous Generator (PMSG) is designed with 2.5 kW
continuous and 6 kW peak power. Then considering generator
geometry, mechanical design of wind turbine is performed. Thermal
analysis and optimization is carried out considering all wind turbine
components to reach realistic results. This issue is extremely
important in research and development (R&D) process for wind
turbine applications.
Abstract: As per the statistical data, the Doubly-fed Induction
Generator (DFIG) based wind turbine with variable speed and
variable pitch control is the most common wind turbine in the
growing wind market. This machine is usually used on the grid
connected wind energy conversion system to satisfy grid code
requirements such as grid stability, Fault Ride Through (FRT), power
quality improvement, grid synchronization and power control etc.
Though the requirements are not fulfilled directly by the machine, the
control strategy is used in both the stator as well as rotor side along
with power electronic converters to fulfil the requirements stated
above. To satisfy the grid code requirements of wind turbine, usually
grid side converter is playing a major role. So in order to improve the
operation capacity of wind turbine under critical situation, the
intensive study of both machine side converter control and grid side
converter control is necessary In this paper DFIG is modeled using
power components as variables and the performance of the DFIG
system is analysed under grid voltage fluctuations. The voltage
fluctuations are made by lowering and raising the voltage values in
the utility grid intentionally for the purpose of simulation keeping in
view of different grid disturbances.
Abstract: In this paper, to model a real life wind turbine, a
probabilistic approach is proposed to model the dynamics of the
blade elements of a small axial wind turbine under extreme stochastic
wind speeds conditions. It was found that the power and the torque
probability density functions even-dough decreases at these extreme
wind speeds but are not infinite. Moreover, we also fund that it
is possible to stabilize the power coefficient (stabilizing the output
power)above rated wind speeds by turning some control parameters.
This method helps to explain the effect of turbulence on the quality
and quantity of the harness power and aerodynamic torque.
Abstract: This paper introduces a method to optimal design of a
hybrid Wind/Photovoltaic/Fuel cell generation system for a typical
domestic load that is not located near the electricity grid. In this
configuration the combination of a battery, an electrolyser, and a
hydrogen storage tank are used as the energy storage system. The aim
of this design is minimization of overall cost of generation scheme
over 20 years of operation. The Matlab/Simulink is applied for
choosing the appropriate structure and the optimization of system
sizing. A teaching learning based optimization is used to optimize the
cost function. An overall power management strategy is designed for
the proposed system to manage power flows among the different
energy sources and the storage unit in the system. The results have
been analyzed in terms of technical and economic. The simulation
results indicate that the proposed hybrid system would be a feasible
solution for stand-alone applications at remote locations.
Abstract: As smartphones are equipped with various sensors,
there have been many studies focused on using these sensors to create
valuable applications. Human activity recognition is one such
application motivated by various welfare applications, such as the
support for the elderly, measurement of calorie consumption, lifestyle
and exercise patterns analyses, and so on. One of the challenges one
faces when using smartphone sensors for activity recognition is that
the number of sensors should be minimized to save battery power. In
this paper, we show that a fairly accurate classifier can be built that
can distinguish ten different activities by using only a single sensor
data, i.e., the smartphone accelerometer data. The approach that we
adopt to deal with this twelve-class problem uses various methods.
The features used for classifying these activities include not only the
magnitude of acceleration vector at each time point, but also the
maximum, the minimum, and the standard deviation of vector
magnitude within a time window. The experiments compared the
performance of four kinds of basic multi-class classifiers and the
performance of four kinds of ensemble learning methods based on
three kinds of basic multi-class classifiers. The results show that
while the method with the highest accuracy is ECOC based on
Random forest.