Abstract: Fuzzy logic system (FLS) is used in this study to
predict the tractive performance in terms of traction force, and
motion resistance for an intelligent air cushion track vehicle while it
operates in the swamp peat. The system is effective to control the
intelligent air –cushion system with measuring the vehicle traction
force (TF), motion resistance (MR), cushion clearance height (CH)
and cushion pressure (CP). Ultrasonic displacement sensor, pull-in
solenoid electromagnetic switch, pressure control sensor, micro
controller, and battery pH sensor are incorporated with the Fuzzy
logic system to investigate experimentally the TF, MR, CH, and CP.
In this study, a comparison for tractive performance of an intelligent
air cushion track vehicle has been performed with the results obtained
from the predicted values of FLS and experimental actual values. The
mean relative error of actual and predicted values from the FLS
model on traction force, and total motion resistance are found as 5.58
%, and 6.78 % respectively. For all parameters, the relative error of
predicted values are found to be less than the acceptable limits. The
goodness of fit of the prediction values from the FLS model on TF,
and MR are found as 0.90, and 0.98 respectively.
Abstract: In this study, the precision heading process of
spur gears has been investigated by means of numerical
analysis. The effect of some parameters such as teeth number
and module on the forming force and material flow were
presented. The simulation works were performed rigid-plastic
finite element method using DEFORM 3D software. In order
to validate the estimated numerical results, they were
compared with those obtained experimentally during heading
of spur gear using lead as a model material. Results showed
that the optimum number of gear teeth is between 10 to 20,
that is because of being the specific pressure in its minimum
value.
Abstract: In this study, the dispersed model is used to predict
gas phase concentration, liquid drop concentration. The venturi
scrubber efficiency is calculated by gas phase concentration. The
modified model has been validated with available experimental data
of Johnstone, Field and Tasler for a range of throat gas velocities,
liquid to gas ratios and particle diameters and is used to study the
effect of some design parameters on collection efficiency.
Abstract: Among all geo-hydrological relationships, rainfallrunoff
relationship is of utmost importance in any hydrological
investigation and water resource planning. Spatial variation, lag time
involved in obtaining areal estimates for the basin as a whole can
affect the parameterization in design stage as well as in planning
stage. In conventional hydrological processing of data, spatial aspect
is either ignored or interpolated at sub-basin level. Temporal
variation when analysed for different stages can provide clues for its
spatial effectiveness. The interplay of space-time variation at pixel
level can provide better understanding of basin parameters.
Sustenance of design structures for different return periods and their
spatial auto-correlations should be studied at different geographical
scales for better management and planning of water resources.
In order to understand the relative effect of spatio-temporal
variation in hydrological data network, a detailed geo-hydrological
analysis of Betwa river catchment falling in Lower Yamuna Basin is
presented in this paper. Moreover, the exact estimates about the
availability of water in the Betwa river catchment, especially in the
wake of recent Betwa-Ken linkage project, need thorough scientific
investigation for better planning. Therefore, an attempt in this
direction is made here to analyse the existing hydrological and
meteorological data with the help of SPSS, GIS and MS-EXCEL
software. A comparison of spatial and temporal correlations at subcatchment
level in case of upper Betwa reaches has been made to
demonstrate the representativeness of rain gauges. First, flows at
different locations are used to derive correlation and regression
coefficients. Then, long-term normal water yield estimates based on
pixel-wise regression coefficients of rainfall-runoff relationship have
been mapped. The areal values obtained from these maps can
definitely improve upon estimates based on point-based
extrapolations or areal interpolations.
Abstract: In aerospace applications, interactions of airflow with
aircraft structures can result in undesirable structural deformations.
This structural deformation in turn, can be predicted if the natural
modes of the structure are known. This can be achieved through
conventional modal testing that requires a known excitation force in
order to extract these dynamic properties. This technique can be
experimentally complex because of the need for artificial excitation
and it is also does not represent actual operational condition. The
current work presents part of research work that address the practical
implementation of operational modal analysis (OMA) applied to a
cantilevered hybrid composite plate employing single contactless
sensing system via laser vibrometer. OMA technique extracts the
modal parameters based only on the measurements of the dynamic
response. The OMA results were verified with impact hammer modal
testing and good agreement was obtained.
Abstract: The present paper discusses the selection of process
parameters for obtaining optimal nanocrystallites size in the CuOZrO2
catalyst. There are some parameters changing the inorganic
structure which have an influence on the role of hydrolysis and
condensation reaction. A statistical design test method is
implemented in order to optimize the experimental conditions of
CuO-ZrO2 nanoparticles preparation. This method is applied for the
experiments and L16 orthogonal array standard. The crystallites size
is considered as an index. This index will be used for the analysis in
the condition where the parameters vary. The effect of pH, H2O/
precursor molar ratio (R), time and temperature of calcination,
chelating agent and alcohol volume are particularity investigated
among all other parameters. In accordance with the results of
Taguchi, it is found that temperature has the greatest impact on the
particle size. The pH and H2O/ precursor molar ratio have low
influences as compared with temperature. The alcohol volume as
well as the time has almost no effect as compared with all other
parameters. Temperature also has an influence on the morphology
and amorphous structure of zirconia. The optimal conditions are
determined by using Taguchi method. The nanocatalyst is studied by
DTA-TG, XRD, EDS, SEM and TEM. The results of this research
indicate that it is possible to vary the structure, morphology and
properties of the sol-gel by controlling the above-mentioned
parameters.
Abstract: Laser Metal Deposition (LMD) is an additive manufacturing process with capabilities that include: producing new
part directly from 3 Dimensional Computer Aided Design (3D CAD)
model, building new part on the existing old component and repairing an existing high valued component parts that would have
been discarded in the past. With all these capabilities and its advantages over other additive manufacturing techniques, the
underlying physics of the LMD process is yet to be fully understood probably because of high interaction between the processing
parameters and studying many parameters at the same time makes it
further complex to understand. In this study, the effect of laser power
and powder flow rate on physical properties (deposition height and
deposition width), metallurgical property (microstructure) and
mechanical (microhardness) properties on laser deposited most
widely used aerospace alloy are studied. Also, because the Ti6Al4V
is very expensive, and LMD is capable of reducing buy-to-fly ratio
of aerospace parts, the material utilization efficiency is also studied.
Four sets of experiments were performed and repeated to establish repeatability using laser power of 1.8 kW and 3.0 kW, powder flow
rate of 2.88 g/min and 5.67 g/min, and keeping the gas flow rate and
scanning speed constant at 2 l/min and 0.005 m/s respectively. The
deposition height / width are found to increase with increase in laser
power and increase in powder flow rate. The material utilization is favoured by higher power while higher powder flow rate reduces
material utilization. The results are presented and fully discussed.
Abstract: Nowadays, the demand for high product quality
focuses extensive attention to the quality of machined surface. The
(CNC) milling machine facilities provides a wide variety of
parameters set-up, making the machining process on the glass
excellent in manufacturing complicated special products compared to
other machining processes. However, the application of grinding
process on the CNC milling machine could be an ideal solution to
improve the product quality, but adopting the right machining
parameters is required. In glass milling operation, several machining
parameters are considered to be significant in affecting surface
roughness. These parameters include the lubrication pressure, spindle
speed, feed rate and depth of cut. In this research work, a fuzzy logic
model is offered to predict the surface roughness of a machined
surface in glass milling operation using CBN grinding tool. Four
membership functions are allocated to be connected with each input
of the model. The predicted results achieved via fuzzy logic model
are compared to the experimental result. The result demonstrated
settlement between the fuzzy model and experimental results with the
93.103% accuracy.
Abstract: We propose a reduced-ordermodel for the instantaneous
hydrodynamic force on a cylinder. The model consists of a system of
two ordinary differential equations (ODEs), which can be integrated
in time to yield very accurate histories of the resultant force and
its direction. In contrast to several existing models, the proposed
model considers the actual (total) hydrodynamic force rather than its
perpendicular or parallel projection (the lift and drag), and captures
the complete force rather than the oscillatory part only. We study
and provide descriptions of the relationship between the model
parameters, evaluated utilizing results from numerical simulations,
and the Reynolds number so that the model can be used at any
arbitrary value within the considered range of 100 to 500 to provide
accurate representation of the force without the need to perform timeconsuming
simulations and solving the partial differential equations
(PDEs) governing the flow field.
Abstract: We report the results of an lattice Boltzmann
simulation of magnetohydrodynamic damping of sidewall convection
in a rectangular enclosure filled with a porous medium. In particular
we investigate the suppression of convection when a steady magnetic
field is applied in the vertical direction. The left and right vertical
walls of the cavity are kept at constant but different temperatures
while both the top and bottom horizontal walls are insulated. The
effects of the controlling parameters involved in the heat transfer and
hydrodynamic characteristics are studied in detail. The heat and mass
transfer mechanisms and the flow characteristics inside the enclosure
depended strongly on the strength of the magnetic field and Darcy
number. The average Nusselt number decreases with rising values of
the Hartmann number while this increases with increasing values of
the Darcy number.
Abstract: This paper presents the possibilities of using Weibull statistical distribution in modeling the distribution of defects in ERP systems. There follows a case study, which examines helpdesk records of defects that were reported as the result of one ERP subsystem upgrade. The result of the applied modeling is in modeling the reliability of the ERP system from a user perspective with estimated parameters like expected maximum number of defects in one day or predicted minimum of defects between two upgrades. Applied measurement-based analysis framework is proved to be suitable in predicting future states of the reliability of the observed ERP subsystems.
Abstract: A CFD study on heat flux reduction in hypersonic flow with opposing jet has been conducted. Flowfield parameters, reattachment point position, surface pressure distributions and heat flux distributions are obtained and validated with experiments. The physical mechanism of heat reduction has been analyzed. When the opposing jet blows, the freestream is blocked off, flows to the edges and not interacts with the surface to form aerodynamic heating. At the same time, the jet flows back to form cool recirculation region, which reduces the difference in temperature between the surface and the nearby gas, and then reduces the heat flux. As the pressure ratio increases, the interface between jet and freestream is gradually pushed away from the surface. Larger the total pressure ratio is, lower the heat flux is. To study the effect of the intensity of opposing jet more reasonably, a new parameter RPA has been introduced by combining the flux and the total pressure ratio. The study shows that the same shock wave position and total heat load can be obtained with the same RPA with different fluxes and the total pressures, which means the new parameter could stand for the intensity of opposing jet and could be used to analyze the influence of opposing jet on flow field and aerodynamic heating.
Abstract: The burst noise is a kind of noises that are destructive
and frequently found in semiconductor devices and ICs, yet detecting
and removing the noise has proved challenging for IC designers or users. According to the properties of burst noise, a methodological
approach is presented (proposed) in the paper, by which the burst noise
can be analysed and detected in time domain. In this paper, principles
and properties of burst noise are expounded first, Afterwards,
feasibility (viable) of burst noise detection by means of wavelet
transform in the time domain is corroborated in the paper, and the multi-resolution characters of Gaussian noise, burst noise and blurred
burst noise are discussed in details by computer emulation. Furthermore, the practical method to decide parameters of wavelet
transform is acquired through a great deal of experiment and data statistics. The methodology may yield an expectation in a wide variety of applications.
Abstract: The analysis of electromagnetic environment using
deterministic mathematical models is characterized by the
impossibility of analyzing a large number of interacting network
stations with a priori unknown parameters, and this is characteristic,
for example, of mobile wireless communication networks. One of the
tasks of the tools used in designing, planning and optimization of
mobile wireless network is to carry out simulation of electromagnetic
environment based on mathematical modelling methods, including
computer experiment, and to estimate its effect on radio
communication devices. This paper proposes the development of a
statistical model of electromagnetic environment of a mobile
wireless communication network by describing the parameters and
factors affecting it including the propagation channel and their
statistical models.
Abstract: Nowadays, quasi-continuous wave diode lasers are
used in a widespread variety of applications. Temperature effects in
these lasers can strongly influence their performance. In this paper,
the effects of temperature have been experimentally investigated on
different features of a 60W-QCW diode laser. The obtained results
indicate that the conversion efficiency and operation voltage of diode
laser decrease with the augmentation of the working temperature
associated with a redshift in the laser peak wavelength. Experimental
results show the emission peak wavelength of laser shifts 0.26 nm
and the conversion efficiency decreases 1.76 % with the increase of
temperature from 40 to 50 ̊C. Present study also shows the slope
efficiency decreases gradually at low temperatures and rapidly at
higher temperatures. Regarding the close dependence of the
mentioned parameters to the operating temperature, it is of great
importance to carefully control the working temperature of diode
laser, particularly for medical applications.
Abstract: In most of the popular implementation of Parallel GAs
the whole population is divided into a set of subpopulations, each
subpopulation executes GA independently and some individuals are
migrated at fixed intervals on a ring topology. In these studies,
the migrations usually occur 'synchronously' among subpopulations.
Therefore, CPUs are not used efficiently and the communication
do not occur efficiently either. A few studies tried asynchronous
migration but it is hard to implement and setting proper parameter
values is difficult.
The aim of our research is to develop a migration method which is
easy to implement, which is easy to set parameter values, and which
reduces communication traffic. In this paper, we propose a traffic
reduction method for the Asynchronous Parallel Distributed GA by
migration of elites only. This is a Server-Client model. Every client
executes GA on a subpopulation and sends an elite information to the
server. The server manages the elite information of each client and
the migrations occur according to the evolution of sub-population in
a client. This facilitates the reduction in communication traffic.
To evaluate our proposed model, we apply it to many function optimization
problems. We confirm that our proposed method performs
as well as current methods, the communication traffic is less, and
setting of the parameters are much easier.
Abstract: The present work consecutively on synthesis and
characterization of composites, Al/Al alloy A 384.1 as matrix in
which the main ingredient as Al/Al-5% MgO alloy based metal
matrix composite. As practical implications the low cost processing
route for the fabrication of Al alloy A 384.1 and operational
difficulties of presently available manufacturing processes based in
liquid manipulation methods. As all new developments, complete
understanding of the influence of processing variables upon the final
quality of the product. And the composite is applied comprehensively
to the acquaintance for achieving superiority of information
concerning the specific heat measurement of a material through the
aid of thermographs. Products are evaluated concerning relative
particle size and mechanical behavior under tensile strength.
Furthermore, Taguchi technique was employed to examine the
experimental optimum results are achieved, owing to effectiveness of
this approach.
Abstract: Films of pure tin oxide SnO2 and in presence of
antimony atoms (SnO2-Sb) deposited onto glass substrates have
shown a sufficiently high energy gap to be transparent in the visible
region, a high electrical mobility and a carrier concentration which
displays a good electrical conductivity [1]. In this work, the effects of
polycrystalline silicon substrate on the optical properties of pure and
Sb doped tin oxide is investigated.
We used the APCVD (atmospheric pressure chemical vapour
deposition) technique, which is a low-cost and simple technique,
under nitrogen ambient, for growing this material. A series of SnO2
and SnO2-Sb have been deposited onto polycrystalline silicon
substrates with different contents of antimony atoms at the same
conditions of deposition (substrate temperature, flow oxygen,
duration and nitrogen atmosphere of the reactor). The effect of the
substrate in terms of morphology and nonlinear optical properties,
mainly the reflectance, was studied. The reflectance intensity of the
device, compared to the reflectance of tin oxide films deposited
directly on glass substrate, is clearly reduced on the overall
wavelength range. It is obvious that the roughness of the poly-c
silicon plays an important role by improving the reflectance and
hence the optical parameters.
A clear shift in the minimum of the reflectance upon doping level
is observed. This minimum corresponds to strong free carrier
absorption, resulting in different plasma frequency. This effect is
followed by an increase in the reflectance depending of the antimony
doping. Applying the extended Drude theory to the combining
optical and electrical obtained results these effects are discussed.
Abstract: Wireless Mesh Networks (WMNs) are an emerging
technology for last-mile broadband access. In WMNs, similar to ad
hoc networks, each user node operates not only as a host but also as a
router. User packets are forwarded to and from an Internet-connected
gateway in multi-hop fashion. The WMNs can be integrated with
other networking technologies i.e. ad hoc networks, to implement a
smooth network extension. The meshed topology provides good
reliability and scalability, as well as low upfront investments. Despite
the recent start-up surge in WMNs, much research remains to be
done in standardizing the functional parameters of WMNs to fully
exploit their full potential. An edifice of the security concerns of
these networks is authentication of a new client joining an integrated
ad hoc network and such a scenario will require execution of a multihop
authentication technique. Our endeavor in this paper is to
introduce a secure authentication technique, with light over-heads
that can be conveniently implemented for the ad-hoc nodes forming
clients of an integrated WMN, thus facilitating their inter-operability.
Abstract: In this paper, the test purpose will be to assess
whether or not the accelerated model proposed by Eyring will be able
to translate results for the shape and scale parameters of an
underlying Weibull model, obtained under two accelerating using
conditions, to expected normal using condition results for these
parameters. The product being analyzed is a new type of insulate
fluid, and the accelerating factor is the voltage stresses applied to the
fluid at two different levels (30KV and 40KV). The normal operating
voltage is 25KV. In this case, it was possible to test the insulate fluid
at normal voltage using condition. Both results for the two
parameters of the Weibull model, obtained under normal using
condition and translated from accelerated using conditions to normal
conditions, will be compared to each other to assess the accuracy of
the Eyring model when the accelerating factor is only the voltage
stress.