Abstract: This paper presents the use of anti-sway angle control
approaches for a two-dimensional gantry crane with disturbances
effect in the dynamic system. Delayed feedback signal (DFS) and
proportional-derivative (PD)-type fuzzy logic controller are the
techniques used in this investigation to actively control the sway
angle of the rope of gantry crane system. A nonlinear overhead
gantry crane system is considered and the dynamic model of the
system is derived using the Euler-Lagrange formulation. A complete
analysis of simulation results for each technique is presented in time
domain and frequency domain respectively. Performances of both
controllers are examined in terms of sway angle suppression and
disturbances cancellation. Finally, a comparative assessment of the
impact of each controller on the system performance is presented and
discussed.
Abstract: Fourier transform infrared (FT-IR) spectroscopic imaging
is an emerging technique that provides both chemically and
spatially resolved information. The rich chemical content of data
may be utilized for computer-aided determinations of structure and
pathologic state (cancer diagnosis) in histological tissue sections for
prostate cancer. FT-IR spectroscopic imaging of prostate tissue has
shown that tissue type (histological) classification can be performed to
a high degree of accuracy [1] and cancer diagnosis can be performed
with an accuracy of about 80% [2] on a microscopic (≈ 6μm)
length scale. In performing these analyses, it has been observed
that there is large variability (more than 60%) between spectra from
different points on tissue that is expected to consist of the same
essential chemical constituents. Spectra at the edges of tissues are
characteristically and consistently different from chemically similar
tissue in the middle of the same sample. Here, we explain these
differences using a rigorous electromagnetic model for light-sample
interaction. Spectra from FT-IR spectroscopic imaging of chemically
heterogeneous samples are different from bulk spectra of individual
chemical constituents of the sample. This is because spectra not
only depend on chemistry, but also on the shape of the sample.
Using coupled wave analysis, we characterize and quantify the nature
of spectral distortions at the edges of tissues. Furthermore, we
present a method of performing histological classification of tissue
samples. Since the mid-infrared spectrum is typically assumed to
be a quantitative measure of chemical composition, classification
results can vary widely due to spectral distortions. However, we
demonstrate that the selection of localized metrics based on chemical
information can make our data robust to the spectral distortions
caused by scattering at the tissue boundary.
Abstract: Ramadan requires individuals to abstain from food and fluid intake between sunrise and sunset; physiological considerations predict that poorer mood, physical performance and mental performance will result. In addition, any difficulties will be worsened because preparations for fasting and recovery from it often mean that nocturnal sleep is decreased in length, and this independently affects mood and performance.
A difficulty of interpretation in many studies is that the observed changes could be due to fasting but also to the decreased length of sleep and altered food and fluid intakes before and after the daytime fasting. These factors were separated in this study, which took place over three separate days and compared the effects of different durations of fasting (4, 8 or 16h) upon a wide variety of measures (including subjective and objective assessments of performance, body composition, dehydration and responses to a short bout of exercise) - but with an unchanged amount of nocturnal sleep, controlled supper the previous evening, controlled intakes at breakfast and daytime naps not being allowed. Many of the negative effects of fasting observed in previous studies were present in this experiment also. These findings indicate that fasting was responsible for many of the changes previously observed, though some effect of sleep loss, particularly if occurring on successive days (as would occur in Ramadan) cannot be excluded.
Abstract: Since injection engines have a considerable portion, in
consumption of energy and environmental pollution, using an
alternative source of energy with lower pollutant effects in this
regard is necessary.
Biodiesel fuel is a suitable alternative for gasoline in diesel
engines.
In this research the property of biodiesel, the function and the
pollution effects of diesel engine, when using 100% biodiesel, using
100% gasoline and mixing ratio of both fuels for comparing them,
have been investigated.
The researches have shown, using biodiesel fuel in prevalent
diesel engine, will reduce the pollutants such as Co, half burned
carbohydrate and suspended particles and a little increase in
oxidation will achieve while power consumption, particularly fuel
and thermal efficiency of diesel fuel has the same.
Abstract: Numerical analysis for the aerodynamic characteristics
of the WIG (wing-in ground effect) craft with highly cambered and
aspect ratio of one is performed to predict the ground effect for the
case of with- and without- lower-extension endplate. The analysis is
included varying angles of attack from 0 to10 deg. and ground
clearances from 5% of chord to 50%. Due to the ground effect, the lift
by rising in pressure on the lower surface is increased and the
influence of wing-tip vortices is decreased. These two significant
effects improve the lift-drag ratio. On the other hand, the endplate
prevents the high-pressure air escaping from the air cushion at the
wing tip and causes to increase the lift and lift-drag ratio further. It is
found from the visualization of computation results that two wing-tip
vortices are generated from each surface of the wing tip and their
strength are weak and diminished rapidly. Irodov-s criteria are also
evaluated to investigate the static height stability. The comparison of
Irodov-s criteria shows that the endplate improves the deviation of the
static height stability with respect to pitch angles and heights. As the
results, the endplate can improve the aerodynamic characteristics and
static height stability of wings in ground effect, simultaneously.
Abstract: Rapid urbanization, industrialization and population
growth have led to an increase in number of automobiles that cause
air pollution. It is estimated that road traffic contributes 60% of air
pollution in urban areas. A case by case assessment is required to
predict the air quality in urban situations, so as to evolve certain
traffic management measures to maintain the air quality levels with
in the tolerable limits. Calicut city in the state of Kerala, India has
been chosen as the study area. Carbon Monoxide (CO) concentration
was monitored at 15 links in Calicut city and air quality performance
was evaluated over each link. The CO pollutant concentration values
were compared with the National Ambient Air Quality Standards
(NAAQS), and the CO values were predicted by using CALINE4 and
IITLS and Linear regression models. The study has revealed that
linear regression model performs better than the CALINE4 and
IITLS models. The possible association between CO pollutant
concentration and traffic parameters like traffic flow, type of vehicle,
and traffic stream speed was also evaluated.
Abstract: In this paper, we present a comparative study between two computer vision systems for objects recognition and tracking, these algorithms describe two different approach based on regions constituted by a set of pixels which parameterized objects in shot sequences. For the image segmentation and objects detection, the FCM technique is used, the overlapping between cluster's distribution is minimized by the use of suitable color space (other that the RGB one). The first technique takes into account a priori probabilities governing the computation of various clusters to track objects. A Parzen kernel method is described and allows identifying the players in each frame, we also show the importance of standard deviation value research of the Gaussian probability density function. Region matching is carried out by an algorithm that operates on the Mahalanobis distance between region descriptors in two subsequent frames and uses singular value decomposition to compute a set of correspondences satisfying both the principle of proximity and the principle of exclusion.
Abstract: A mathematical model for the Dynamics of Economic
Profit is constructed by proposing a characteristic differential oneform
for this dynamics (analogous to the action in Hamiltonian
dynamics). After processing this form with exterior calculus, a pair of
characteristic differential equations is generated and solved for the
rate of change of profit P as a function of revenue R (t) and cost C (t).
By contracting the characteristic differential one-form with a vortex
vector, the Lagrangian is obtained for the Dynamics of Economic
Profit.
Abstract: When reconstructing a scenario, it is necessary to
know the structure of the elements present on the scene to have an
interpretation. In this work we link 3D scenes reconstruction to
evolutionary algorithms through the vision stereo theory. We
consider vision stereo as a method that provides the reconstruction of
a scene using only a couple of images of the scene and performing
some computation. Through several images of a scene, captured from
different positions, vision stereo can give us an idea about the threedimensional
characteristics of the world. Vision stereo usually
requires of two cameras, making an analogy to the mammalian vision
system. In this work we employ only a camera, which is translated
along a path, capturing images every certain distance. As we can not
perform all computations required for an exhaustive reconstruction,
we employ an evolutionary algorithm to partially reconstruct the
scene in real time. The algorithm employed is the fly algorithm,
which employ “flies" to reconstruct the principal characteristics of
the world following certain evolutionary rules.
Abstract: This paper reviews the objectives, methods and results of previous studies on biodrying of solid waste in several countries. Biodrying of solid waste is a novel technology in developing countries such as in Malaysia where high moisture content in organic waste makes the segregation process for recycling purposes complicated and diminishes the calorific value for the use of fuel source. In addition, the high moisture content also encourages the breeding of vectors and disease-bearing animals. From the laboratory results, the average moisture content of organic waste, paper, plastics and metals are 58.17%, 37.93%, 29.79% and 1.03% respectively for UKM campus. Biodrying of solid waste is a simple method of waste treatment as well as a cost-efficient technology to dry the solid waste. The process depends on temperature monitoring and air flow control along with the natural biodegradable process of organic waste. This review shows that the biodrying of solid waste method has high potential in treatment and recycling of solid waste, be useful for biodrying study and implementation in Malaysia.
Abstract: We present the development of a new underwater laser
cutting process in which a water-jet has been used along with the
laser beam to remove the molten material through kerf. The
conventional underwater laser cutting usually utilizes a high pressure
gas jet along with laser beam to create a dry condition in the cutting
zone and also to eject out the molten material. This causes a lot of gas
bubbles and turbulence in water, and produces aerosols and waste
gas. This may cause contamination in the surrounding atmosphere
while cutting radioactive components like burnt nuclear fuel. The
water-jet assisted underwater laser cutting process produces much
less turbulence and aerosols in the atmosphere. Some amount of
water vapor bubbles is formed at the laser-metal-water interface;
however, they tend to condense as they rise up through the
surrounding water. We present the design and development of a
water-jet assisted underwater laser cutting head and the parametric
study of the cutting of AISI 304 stainless steel sheets with a 2 kW
CW fiber laser. The cutting performance is similar to that of the gas
assist laser cutting; however, the process efficiency is reduced due to
heat convection by water-jet and laser beam scattering by vapor. This
process may be attractive for underwater cutting of nuclear reactor
components.
Abstract: The performance and the plasma created by a pulsed
magnetoplasmadynamic thruster for small satellite application is
studied to understand better the ablation and plasma propagation
processes occurring during the short-time discharge. The results can
be applied to improve the quality of the thruster in terms of efficiency,
and to tune the propulsion system to the needs required by the satellite
mission. Therefore, plasma measurements with a high-speed camera
and induction probes, and performance measurements of mass bit
and impulse bit were conducted. Values for current sheet propagation
speed, mean exhaust velocity and thrust efficiency were derived from
these experimental data. A maximum in current sheet propagation
was found by the high-speed camera measurements for a medium
energy input and confirmed by the induction probes. A quasilinear
tendency between the mass bit and the energy input, the current
action integral respectively, was found, as well as a linear tendency
between the created impulse and the discharge energy. The highest
mean exhaust velocity and thrust efficiency was found for the highest
energy input.
Abstract: This paper proposes a method, combining color and layout features, for identifying documents captured from low-resolution handheld devices. On one hand, the document image color density surface is estimated and represented with an equivalent ellipse and on the other hand, the document shallow layout structure is computed and hierarchically represented. Our identification method first uses the color information in the documents in order to focus the search space on documents having a similar color distribution, and finally selects the document having the most similar layout structure in the remaining of the search space.
Abstract: A cross sectional survey design was used to collect
data from 370 diabetic patients. Two instruments were used in
obtaining data; in-depth interview guide and researchers- developed
questionnaire. Fisher's exact test was used to investigate association
between the identified factors and nonadherence. Factors identified
were: socio-demographic factors such as: gender, age, marital status,
educational level and occupation; psychosocial obstacles such as:
non-affordability of prescribed diet, frustration due to the restriction,
limited spousal support, feelings of deprivation, feeling that
temptation is inevitable, difficulty in adhering in social gatherings
and difficulty in revealing to host that one is diabetic; health care
providers obstacles were: poor attitude of health workers, irregular
diabetes education in clinics , limited number of nutrition education
sessions/ inability of the patients to estimate the desired quantity of
food, no reminder post cards or phone calls about upcoming patient
appointments and delayed start of appointment / time wasting in
clinics.
Abstract: Economically transformers constitute one of the largest investments in a Power system. For this reason, transformer condition assessment and management is a high priority task. If a transformer fails, it would have a significant negative impact on revenue and service reliability. Monitoring the state of health of power transformers has traditionally been carried out using laboratory Dissolved Gas Analysis (DGA) tests performed at periodic intervals on the oil sample, collected from the transformers. DGA of transformer oil is the single best indicator of a transformer-s overall condition and is a universal practice today, which started somewhere in the 1960s. Failure can occur in a transformer due to different reasons. Some failures can be limited or prevented by maintenance. Oil filtration is one of the methods to remove the dissolve gases and prevent the deterioration of the oil. In this paper we analysis the DGA data by regression method and predict the gas concentration in the oil in the future. We bring about a comparative study of different traditional methods of regression and the errors generated out of their predictions. With the help of these data we can deduce the health of the transformer by finding the type of fault if it has occurred or will occur in future. Additional in this paper effect of filtration on the transformer health is highlight by calculating the probability of failure of a transformer with and without oil filtrating.
Abstract: In the past years, the world has witnessed significant work in the field of Manufacturing. Special efforts have been made in the implementation of new technologies, management and control systems, among many others which have all evolved the field. Closely following all this, due to the scope of new projects and the need of turning the existing flexible ideas into more autonomous and intelligent ones, i.e.: moving toward a more intelligent manufacturing, the present paper emerges with the main aim of contributing to the analysis and a few customization issues of a new iCIM 3000 system at the IPSAM. In this process, special emphasis in made on the material flow problem. For this, besides offering a description and analysis of the system and its main parts, also some tips on how to define other possible alternative material flow scenarios and a partial analysis of the combinatorial nature of the problem are offered as well. All this is done with the intentions of relating it with the use of simulation tools, for which these have been briefly addressed with a special focus on the Witness simulation package. For a better comprehension, the previous elements are supported by a few figures and expressions which would help obtaining necessary data. Such data and others will be used in the future, when simulating the scenarios in the search of the best material flow configurations.
Abstract: A catastrophic earthquake measuring 6.3 on the
Richter scale struck the Christchurch, New Zealand Central Business
District on February 22, 2012, abruptly disrupting the business of
teaching and learning at Christchurch Polytechnic Institute of
Technology. This paper presents the findings from a study
undertaken about the complexity of delivering an educational
programme in the face of this traumatic natural event. Nine
interconnected themes emerged from this multiple method study:
communication, decision making, leader- and follower-ship,
balancing personal and professional responsibilities, taking action,
preparedness and thinking ahead, all within a disruptive and uncertain
context. Sustainable responses that maximise business continuity, and
provide solutions to practical challenges, are among the study-s
recommendations.
Abstract: Design and modeling of nonlinear systems require the
knowledge of all inside acting parameters and effects. An empirical
alternative is to identify the system-s transfer function from input and
output data as a black box model. This paper presents a procedure
using least squares algorithm for the identification of a feed drive
system coefficients in time domain using a reduced model based on
windowed input and output data. The command and response of the
axis are first measured in the first 4 ms, and then least squares are
applied to predict the transfer function coefficients for this
displacement segment. From the identified coefficients, the next
command response segments are estimated. The obtained results
reveal a considerable potential of least squares method to identify the
system-s time-based coefficients and predict accurately the command
response as compared to measurements.
Abstract: Studies were carried out to determine the in vitro
susceptibility of the typhoid pathogens to combined action of Euphorbia hirta, Euphorbia heterophylla and Phyllanthus niruri. Clinical isolates of the typhoid bacilli were subjected to susceptibility testing using agar diffusion technique and the minimum inhibitory
concentration (MIC) determined with tube dilution technique. These
isolates, when challenged with doses of the extracts from the three
medicinal plants showed zones of inhibition as wide as 26±0.2mm, 22±0.1mm and 18±0.0mm respectively. The minimum inhibitory concentration (MIC) revealed organisms inhibited at varying
concentrations of extracts: E. hirta (S. typhi 0.250mg/ml, S. paratyphi A 0.125mg/ml, S. paratyphi B 0.185mg/ml and S. paratyphi C 0.225mg/ml), E. heterophylla (S. typhi 0.280mg/ml, S. paratyphi A
0.150mg/ml, S. paratyphi B 0.200mg/ml and S. paratyphi C 0.250mg/ml) and P. niruri (S. typhi 0.150mg/ml, S. paratyphi A 0.100mg/ml, S. paratyphi B 0.115mg/ml and S. paratyphi C 0.125mg/ml). The results of the synergy between the three plants in
the ration of 1:1:1 showed very low MICs for the test pathogens as follows S. typhi 0.025mg/ml, S. paratyphi A 0.080mg/ml, S. paratyphi B 0.015mg/ml and S. paratyphi C 0.10mg/ml with the
diameter zone of inhibition (DZI) ranging from 35±0.2mm,
28±0.4mm, 20±0.1mm and 32±0.3mm respectively. The secondary
metabolites were identified using simple methods and HPLC. Organic components such as anthroquinones, different alkaloids,
tannins, 6-ethoxy-1,2,3,4-tetrahydro-2,2,4-trimethyl and steroids were identified. The prevalence of Salmonellae, a deadly infectious disease, is still very high in parts of Nigeria. The synergistic action of these three plants is very high. It is concluded that pharmaceutical companies should take advantage of these findings to develop new
anti-typhoid drugs from these plants.
Abstract: The purpose of the study was to determine if, among
32 brain injured adults in community rehabilitation programs, there is
a statistically significant relationship between the degree of severity
of brain injury and these adults- level of self-esteem and stress. The
researcher hypothesized there would be a statistically significant
difference and a statistically significant relationship in self-esteem
and stress levels among and TBI adults. A Pearson product moment
correlational analysis was implemented and results found a
statistically significant relationship between self-esteem and stress
levels. Future recommendations were suggested upon completion of
research.