Abstract: Sweep frequency response analysis has been turning
out a powerful tool for investigation of mechanical as well as
electrical integration of transformers. In this paper various aspect of
practical application of SFRA has been studied. Open circuit and
short circuit measurement were done on different phases of high
voltage and low voltage winding. A case study was presented for the
transformer of rating 31.5 MVA for various frequency ranges. A
clear picture was presented for sub- frequency ranges for HV as well
as LV winding. The main motive of work is to investigate high
voltage short circuit response. The theoretical concept about SFRA
responses is validated with expert system software results.
Abstract: Polymorphism is one of the main pillars of objectoriented
paradigm. It induces hidden forms of class dependencies
which may impact software quality, resulting in higher cost factor for
comprehending, debugging, testing, and maintaining the software. In
this paper, a new cognitive complexity metric called Cognitive
Weighted Polymorphism Factor (CWPF) is proposed. Apart from the
software structural complexity, it includes the cognitive complexity
on the basis of type. The cognitive weights are calibrated based on 27
empirical studies with 120 persons. A case study and experimentation
of the new software metric shows positive results. Further, a
comparative study is made and the correlation test has proved that
CWPF complexity metric is a better, more comprehensive, and more
realistic indicator of the software complexity than Abreu’s
Polymorphism Factor (PF) complexity metric.
Abstract: Annihilations, phase shifts, scattering lengths and
elastic cross sections of low energy positrons scattering from
magnesium atoms were studied using the least-squares variational
method (LSVM). The possibility of positron binding to the
magnesium atoms is investigated. A trial wave function is suggested
to represent e+-Mg elastic scattering and scattering parameters were
derived to estimate the binding energy and annihilation rates. The
trial function is taken to depend on several adjustable parameters, and
is improved iteratively by increasing the number of terms. The
present results have the same behavior as reported semi-empirical,
theoretical and experimental results. Especially, the estimated
positive scattering length supports the possibility of positronmagnesium
bound state system that was confirmed in previous
experimental and theoretical work.
Abstract: Here, we have shown the reaction of [Cr(ArN(CH2)3NAr)2Cl2] (1) where (Ar = 2,6-Pri
2C6H3) and in presence of NaCp (2) (Cp= C5H5 = cyclopentadien), with a center
coordination η5 interaction between Cp as co-ligand and chromium
metal center, for optimization we used density functional theory
(DFT), under methods, explicitly including electrons correlations, for
the final calculations as MB3LYP (Becke) (Lee–Yang–Parr) level of
theory we used to obtain more exact results. This complex was
calculated as electronic energy for molecular system, because the
calculation accounting all electrons correlations interactions. The
optimised of [Cr(ArN(CH2)3NAr)2(η5-Cp)] (Ar = 2,6-Pri2C6H3 and Cp = C5H5) was found to be thermally stable. By using Dewar-Chatt-Duncanson model, as a basis of the molecular orbital (MO) analysis
and showed the highest occupied molecular orbital (HOMO) and
lowest occupied molecular orbital LUMO.
Abstract: This paper presents the advantages of fuzzy control use in technological processes control. The paper presents a real application of the Linguistic Fuzzy-Logic Control, developed at the University of Ostrava for the control of physical models in the Intelligent Systems Laboratory. The paper presents an example of a sensitive non-linear model, such as a magnetic levitation model and obtained results which show how modern information technologies can help to solve actual technical problems. A special method based on the LFLC controller with partial components is presented in this paper followed by the method of automatic context change, which is very helpful to achieve more accurate control results. The main advantage of the used system is its robustness in changing conditions demonstrated by comparing with conventional PID controller. This technology and real models are also used as a background for problem-oriented teaching, realized at the department for master students and their collaborative as well as individual final projects.
Abstract: In this paper, the results of Kano from one dimensional
cosine and sine series are extended to two dimensional cosine and sine
series. To extend these results, some classes of coefficient sequences
such as class of semi convexity and class R are extended from
one dimension to two dimensions. Further, the function f(x, y) is
two dimensional Fourier Cosine and Sine series or equivalently it
represents an integrable function or not, has been studied. Moreover,
some results are obtained which are generalization of Moricz’s
results.
Abstract: The UK is leading in online retail and mobile
adoption. However, there is a dearth of information relating to mobile
apparel retail, and developing an understanding about consumer
browsing and purchase behaviour in m-retail channel would provide
apparel marketers, mobile website and app developers with the
necessary understanding of consumers’ needs. Despite the rapid
growth of mobile retail businesses, no published study has examined
shopping behaviour on fashion mobile apps and websites. A mixed method approach helped to understand why fashion
consumers prefer websites on smartphones, when diverse mobile
apps are also available. The following research methods were
employed: survey, eye-tracking experiments, observation, and
interview with retrospective think aloud. The mobile gaze tracking
device by SensoMotoric Instruments was used to understand
frustrations in navigation and other issues facing consumers in
mobile channel. This method helped to validate and compliment
other traditional user-testing approaches in order to optimize user
experience and enhance the development of mobile retail channel.
The study involved eight participants - females aged 18 to 35 years
old, who are existing mobile shoppers. The participants used the
Topshop mobile app and website on a smart phone to complete a task
according to a specified scenario leading to a purchase. The
comparative study was based on: duration and time spent at different
stages of the shopping journey, number of steps involved and product
pages visited, search approaches used, layout and visual clues, as
well as consumer perceptions and expectations. The results from the data analysis show significant differences in
consumer behaviour when using a mobile app or website on a smart
phone. Moreover, two types of problems were identified, namely
technical issues and human errors. Having a mobile app does not
guarantee success in satisfying mobile fashion consumers. The
differences in the layout and visual clues seem to influence the
overall shopping experience on a smart phone. The layout of search
results on the website was different from the mobile app. Therefore,
participants, in most cases, behaved differently on different
platforms. The number of product pages visited on the mobile app
was triple the number visited on the website due to a limited visibility
of products in the search results. Although, the data on traffic trends
held by retailers to date, including retail sector breakdowns for visits
and views, data on device splits and duration, might seem a valuable
source of information, it cannot explain why consumers visit many
product pages, stay longer on the website or mobile app, or abandon
the basket. A comprehensive list of pros and cons was developed by
highlighting issues for website and mobile app, and recommendations
provided. The findings suggest that fashion retailers need to be aware of
actual consumers’ behaviour on the mobile channel and their expectations in order to offer a seamless shopping experience. Added
to which is the challenge of retaining existing and acquiring new
customers. There seem to be differences in the way fashion
consumers search and shop on mobile, which need to be explored in
further studies.
Abstract: This study aims to assess the students' needs for the
tour planning e-guide. The study is developing on the contribution
and importance of the Educational Tour Planning Guide (ETP) is a
multimedia course ware as one of the effective methods in teaching
and learning of environmental science among the students in primary
schools of the Ministry of Education, Malaysia. It is to provide the
student with knowledge and experience about tourism, environmental
science activities and process. E-guide to ETP also hopes to
strengthen the student understanding toward the subject learn in the
tourism environmental science. In order to assess the student's needs
on the e-Guide to Educational Tour Planning in Environmental
Science, the study has produced a similar e-Guide to ETP in the form
as a course ware to be tested during the study. The study has involved
several steps in order to be completed. It is such as the formulation of
the problem, the review of the literature, the formulation of the study
methodology, the production of the e-Guide to ETP, field survey and
finally the analyses and discussion made on the data gathered during
the study. The survey has involved 100 respondents among the
students in standard six primary schools in Kluang Johor. Through
the findings, the study indicates that the current tested product is
acceptable among the students in learning environmental science as a
guide to plan for the tour. The findings also show a slight difference
between the respondents who are using the e-Guide to ETP, and those
who are not on the basis of the e-Guide to ETP results. Due the
important for the study, the researcher hopes to be having a fair
discussion and excellence, recommendation for the development of
the product of the current study. This report is written also important
to provide a written reference for the future related study.
Abstract: In the present study, analysis of heat transfer is carried
out in the slip flow region for the fluid flowing between two parallel
plates by employing the asymmetric heat fluxes at surface of the
plates. The flow is assumed to be hydrodynamically and thermally
fully developed for the analysis. The second order velocity slip and
viscous dissipation effects are considered for the analysis. Closed
form expressions are obtained for the Nusselt number as a function of
Knudsen number and modified Brinkman number. The limiting
condition of the present prediction for Kn = 0, Kn2 = 0, and Brq1 = 0
is considered and found to agree well with other analytical results.
Abstract: In this paper, a asymptotically periodic predator-prey
model with Modified Leslie-Gower and Holling-Type II schemes
is investigated. Some sufficient conditions for the uniformly strong
persistence of the system are established. Our result is an important
complementarity to the earlier results.
Abstract: The work reported through this paper is an
experimental work conducted on High Performance Concrete (HPC)
with super plasticizer with the aim to develop some models suitable
for prediction of compressive strength of HPC mixes. In this study,
the effect of varying proportions of fly ash (0% to 50% @ 10%
increment) on compressive strength of high performance concrete has
been evaluated. The mix designs studied were M30, M40 and M50 to
compare the effect of fly ash addition on the properties of these
concrete mixes. In all eighteen concrete mixes that have been
designed, three were conventional concretes for three grades under
discussion and fifteen were HPC with fly ash with varying
percentages of fly ash. The concrete mix designing has been done in
accordance with Indian standard recommended guidelines. All the
concrete mixes have been studied in terms of compressive strength at
7 days, 28 days, 90 days, and 365 days. All the materials used have
been kept same throughout the study to get a perfect comparison of
values of results. The models for compressive strength prediction
have been developed using Linear Regression method (LR), Artificial
Neural Network (ANN) and Leave-One-Out Validation (LOOV)
methods.
Abstract: In this numerical work, mixed convection and entropy
generation of Cu–water nanofluid in a lid-driven square cavity have
been investigated numerically using the Lattice Boltzmann Method.
Horizontal walls of the cavity are adiabatic and vertical walls have
constant temperature but different values. The top wall has been
considered as moving from left to right at a constant speed, U0. The
effects of different parameters such as nanoparticle volume
concentration (0–0.05), Rayleigh number (104–106) and Reynolds
numbers (1, 10 and 100) on the entropy generation, flow and
temperature fields are studied. The results have shown that addition
of nanoparticles to the base fluid affects the entropy generation, flow
pattern and thermal behavior especially at higher Rayleigh and low
Reynolds numbers. For pure fluid as well as nanofluid, the increase
of Reynolds number increases the average Nusselt number and the
total entropy generation, linearly. The maximum entropy generation
occurs in nanofluid at low Rayleigh number and at high Reynolds
number. The minimum entropy generation occurs in pure fluid at low
Rayleigh and Reynolds numbers. Also at higher Reynolds number,
the effect of Cu nanoparticles on enhancement of heat transfer was
decreased because the effect of lid-driven cavity was increased. The
present results are validated by favorable comparisons with
previously published results. The results of the problem are presented
in graphical and tabular forms and discussed.
Abstract: In recent years, new techniques for solving complex
problems in engineering are proposed. One of these techniques is
JPSO algorithm. With innovative changes in the nature of the jump
algorithm JPSO, it is possible to construct a graph-based solution
with a new algorithm called G-JPSO. In this paper, a new algorithm
to solve the optimal control problem Fletcher-Powell and optimal
control of pumps in water distribution network was evaluated.
Optimal control of pumps comprise of optimum timetable operation
(status on and off) for each of the pumps at the desired time interval.
Maximum number of status on and off for each pumps imposed to the
objective function as another constraint. To determine the optimal
operation of pumps, a model-based optimization-simulation
algorithm was developed based on G-JPSO and JPSO algorithms.
The proposed algorithm results were compared well with the ant
colony algorithm, genetic and JPSO results. This shows the
robustness of proposed algorithm in finding near optimum solutions
with reasonable computational cost.
Abstract: This research studies the joint production,
maintenance and subcontracting control policy for an unreliable
deteriorating manufacturing system. Production activities are
controlled by a derivation of the Hedging Point Policy, and given that
the system is subject to deterioration, it reduces progressively its
capacity to satisfy product demand. Multiple deterioration effects are
considered, reflected mainly in the quality of the parts produced and
the reliability of the machine. Subcontracting is available as support
to satisfy product demand; also, overhaul maintenance can be
conducted to reduce the effects of deterioration. The main objective
of the research is to determine simultaneously the production,
maintenance and subcontracting rate, which minimize the total,
incurred cost. A stochastic dynamic programming model is
developed and solved through a simulation-based approach
composed of statistical analysis and optimization with the response
surface methodology. The obtained results highlight the strong
interactions between production, deterioration and quality, which
justify the development of an integrated model. A numerical example
and a sensitivity analysis are presented to validate our results.
Abstract: The apportionment method is used by many countries, to calculate the distribution of seats in political bodies. For example, this method is used in the United States (U.S.) to distribute house seats proportionally based on the population of the electoral district. Famous apportionment methods include the divisor methods called the Adams Method, Dean Method, Hill Method, Jefferson Method and Webster Method. Sometimes the results from the implementation of these divisor methods are unfair and include errors. Therefore, it is important to examine the optimization of this method by using a bias measurement to figure out precise and fair results. In this research we investigate the bias of divisor methods in the U.S. Houses of Representatives toward large and small states by applying the Stolarsky Mean Method. We compare the bias of the apportionment method by using two famous bias measurements: the Balinski and Young measurement and the Ernst measurement. Both measurements have a formula for large and small states. The Third measurement however, which was created by the researchers, did not factor in the element of large and small states into the formula. All three measurements are compared and the results show that our measurement produces similar results to the other two famous measurements.
Abstract: This paper presents the results of a Finite Element
based vibration analysis of a solar powered Unmanned Aerial
Vehicle (UAV). The purpose of this paper was to quantify the free
vibration, forced vibration response due to differing point inputs in
order to predict the relative response magnitudes and frequencies at
various wing locations of vibration induced power generators
(magnet in coil) excited by gust and/or control surface pulse-decays
used to help power the flight of the electric UAV. A Fluid Structure
Interaction (FSI) study was performed in order to ascertain pertinent
design stresses and deflections as well as aerodynamic parameters of
the UAV airfoil. The 10 ft span airfoil is modeled using Mylar as the
primary material. Results show that the free mode in bending is 4.8
Hz while the first forced bending mode is on range of 16.2 to 16.7 Hz
depending on the location of excitation. The free torsional bending
mode is 28.3 Hz, and the first forced torsional mode is range of 26.4
to 27.8 Hz, depending on the location of excitation. The FSI results
predict the coefficients of aerodynamic drag and lift of 0.0052 and
0.077, respectively, which matches hand-calculations used to validate
the Finite Element based results. FSI based maximum von Mises
stresses and deflections were found to be 0.282 MPa and 3.4 mm,
respectively. Dynamic pressures on the airfoil range from 1.04 to
1.23 kPa corresponding to velocity magnitudes in range of 22 to 66
m/s.
Abstract: The end of the line controls of the finished products in
the automotive industry is important. The control that has been
conducted with the manual methods for the sliding doors tracks is not
sufficient and faulty products cannot be identified. As a result, the
customer has the faulty products. In the scope of this study, the
design criteria of the PLC integrated modular end of line control unit
has been examined, designed and manufactured to make the control
of the 10 different track profile to 2 different vehicles with an
objective to minimize the salvage costs by obtaining more sensitive,
certain and accurate measurement results. In the study that started
with literature and patent review, the design inputs have been
specified, the technical concept has been developed, computer
supported mechanic design, control system and automation design,
design review and design improvement have been made. Laser
analog sensors at high sensitivity, probes and modular blocks have
been used in the unit. The measurement has been conducted in the
system and it is observed that measurement results are more sensitive
than the previous methods that we use.
Abstract: This paper investigates the thermal issue of permanent
magnet synchronous generator which is frequently used in direct
drive gearless small-scale wind turbine applications. Permanent
Magnet Synchronous Generator (PMSG) is designed with 2.5 kW
continuous and 6 kW peak power. Then considering generator
geometry, mechanical design of wind turbine is performed. Thermal
analysis and optimization is carried out considering all wind turbine
components to reach realistic results. This issue is extremely
important in research and development (R&D) process for wind
turbine applications.
Abstract: Although there has been a growing interest in the
hybrid free-space optical link and radio frequency FSO/RF
communication system, the current literature is limited to results
obtained in moderate or cold environment. In this paper, using a soft
switching approach, we investigate the effect of weather
inhomogeneities on the strength of turbulence hence the channel
refractive index under Qatar harsh environment and their influence
on the hybrid FSO/RF availability. In this approach, either FSO/RF
or simultaneous or none of them can be active. Based on soft
switching approach and a finite state Markov Chain (FSMC) process,
we model the channel fading for the two links and derive a
mathematical expression for the outage probability of the hybrid
system. Then, we evaluate the behavior of the hybrid FSO/RF under
hazy and harsh weather. Results show that the FSO/RF soft switching
renders the system outage probability less than that of each link
individually. A soft switching algorithm is being implemented on
FPGAs using Raptor code interfaced to the two terminals of a
1Gbps/100 Mbps FSO/RF hybrid system, the first being implemented
in the region. Experimental results are compared to the above
simulation results.
Abstract: Water resource systems modeling has constantly been
a challenge through history for human beings. As the innovative
methodological development is evolving alongside computer sciences
on one hand, researches are likely to confront more complex and
larger water resources systems due to new challenges regarding
increased water demands, climate change and human interventions,
socio-economic concerns, and environment protection and
sustainability. In this research, an automatic calibration scheme has
been applied on the Gilan’s large-scale water resource model using
mathematical programming. The water resource model’s calibration
is developed in order to attune unknown water return flows from
demand sites in the complex Sefidroud irrigation network and other
related areas. The calibration procedure is validated by comparing
several gauged river outflows from the system in the past with model
results. The calibration results are pleasantly reasonable presenting a
rational insight of the system. Subsequently, the unknown optimized
parameters were used in a basin-scale linear optimization model with
the ability to evaluate the system’s performance against a reduced
inflow scenario in future. Results showed an acceptable match
between predicted and observed outflows from the system at selected
hydrometric stations. Moreover, an efficient operating policy was
determined for Sefidroud dam leading to a minimum water shortage
in the reduced inflow scenario.