Abstract: This paper presents the design and analysis of Liquid Crystal (LC) based tunable reflectarray antenna with slot embedded patch element configurations within X-band frequency range. The slots are shown to modify the surface current distribution on the patch element of reflectarray which causes the resonant patch element to provide different resonant frequencies depending on the slot dimensions. The simulated results are supported and verified by waveguide scattering parameter measurements of different reflectarray unit cells. Different rectangular slots on patch element have been fabricated and a change in resonant frequency from 10.46GHz to 8.78GHz has been demonstrated as the width of the rectangular slot is varied from 0.2W to 0.6W. The rectangular slot in the center of the patch element has also been utilized for the frequency tunable reflectarray antenna design based on K-15 Nematic LC. For the active reflectarray antenna design, a frequency tunability of 1.2% from 10GHz to 9.88GHz has been demonstrated with a dynamic phase range of 103° provided by the measured scattering parameter results. Time consumed by liquid crystals for reconfiguration, which is one of the drawback of LC based design, has also been disused in this paper.
Abstract: Growth and remodeling of biological structures have
gained lots of attention over the past decades. Determining the
response of living tissues to mechanical loads is necessary for a wide
range of developing fields such as prosthetics design or computerassisted
surgical interventions. It is a well-known fact that biological
structures are never stress-free, even when externally unloaded. The
exact origin of these residual stresses is not clear, but theoretically,
growth is one of the main sources. Extracting body organ’s shapes
from medical imaging does not produce any information regarding
the existing residual stresses in that organ. The simplest cause of such
stresses is gravity since an organ grows under its influence from
birth. Ignoring such residual stresses might cause erroneous results in
numerical simulations. Accounting for residual stresses due to tissue
growth can improve the accuracy of mechanical analysis results. This
paper presents an original computational framework based on gradual
growth to determine the residual stresses due to growth. To illustrate
the method, we apply it to a finite element model of a healthy human
face reconstructed from medical images. The distribution of residual
stress in facial tissues is computed, which can overcome the effect of
gravity and maintain tissues firmness. Our assumption is that tissue
wrinkles caused by aging could be a consequence of decreasing
residual stress and thus not counteracting gravity. Taking into
account these stresses seems therefore extremely important in
maxillofacial surgery. It would indeed help surgeons to estimate
tissues changes after surgery.
Abstract: This paper presents the strategic development plan of
winged rockets WIRES (WInged REusable Sounding rocket) aiming
at unmanned suborbital winged rocket for demonstrating future fully
reusable space transportation technologies, such as aerodynamics,
Navigation, Guidance and Control (NGC), composite structure,
propulsion system, and cryogenic tanks etc., by universities in
collaboration with government and industries, as well as the past and
current flight test results.
Abstract: This paper outlines the development of an
experimental technique in quantifying supersonic jet flows, in an
attempt to avoid seeding particle problems frequently associated with
particle-image velocimetry (PIV) techniques at high Mach numbers.
Based on optical flow algorithms, the idea behind the technique
involves using high speed cameras to capture Schlieren images of the
supersonic jet shear layers, before they are subjected to an adapted
optical flow algorithm based on the Horn-Schnuck method to
determine the associated flow fields. The proposed method is capable
of offering full-field unsteady flow information with potentially
higher accuracy and resolution than existing point-measurements or
PIV techniques. Preliminary study via numerical simulations of a
circular de Laval jet nozzle successfully reveals flow and shock
structures typically associated with supersonic jet flows, which serve
as useful data for subsequent validation of the optical flow based
experimental results. For experimental technique, a Z-type Schlieren
setup is proposed with supersonic jet operated in cold mode,
stagnation pressure of 4 bar and exit Mach of 1.5. High-speed singleframe
or double-frame cameras are used to capture successive
Schlieren images. As implementation of optical flow technique to
supersonic flows remains rare, the current focus revolves around
methodology validation through synthetic images. The results of
validation test offers valuable insight into how the optical flow
algorithm can be further improved to improve robustness and
accuracy. Despite these challenges however, this supersonic flow
measurement technique may potentially offer a simpler way to
identify and quantify the fine spatial structures within the shock shear
layer.
Abstract: The present study investigates the effectiveness of
newly designed clayey pellets (fired clay pellets diameter sizes of 5
and 8 mm, and unfired clay pellets with the diameter size of 15 mm)
as the beds in the column adsorption process. The adsorption
experiments in the batch mode were performed before the column
experiment with the purpose to determine the order of adsorbent
package in the column which was to be designed in the investigation.
The column experiment was performed by using a known mass of the
clayey beds and the volume of the waste printing developer, which
was purified. The column was filled in the following order: fired clay
pellets of the diameter size of 5 mm, fired clay pellets of the diameter
size of 8 mm, and unfired clay pellets of the diameter size of 15 mm.
The selected order of the adsorbents showed a high removal
efficiency for zinc (97.8%) and copper (81.5%) ions. These
efficiencies were better than those in the case of the already existing
mode adsorption. The obtained experimental data present a good
basis for the selection of an appropriate column fill, but further
testing is necessary in order to obtain more accurate results.
Abstract: Biodiesel is widely investigated to solve the twin
problem of depletion of fossil fuel and environmental degradation.
The main objective of the present work is to compare performance,
emissions, and combustion characteristics of biodiesel derived from
cotton seed oil in a diesel engine with the baseline results of
petrodiesel fuel. Tests have been conducted on a single cylinder, four
stroke CIDI diesel engine with a speed of 1500 rpm and a fixed
compression ratio of 17.5 at different load conditions. The
performance parameters evaluated include brake thermal efficiency,
brake specific fuel consumption, brake power, indicated mean
effective pressure, mechanical efficiency, and exhaust gas
temperature. Regarding combustion study, cylinder pressure, rate of
pressure rise, net heat release rate, cumulative heat release, mean gas
temperature, mass fraction burned, and fuel line pressure were
evaluated. The emission parameters such as carbon monoxide, carbon
dioxide, un-burnt hydrocarbon, oxides of nitrogen, and smoke
opacity were also measured by a smoke meter and an exhaust gas
analyzer and compared with baseline results. The brake thermal
efficiency of cotton seed oil methyl ester (CSOME) was lower than
that of petrodiesel and brake specific fuel consumption was found to
be higher. However, biodiesel resulted in the reduction of carbon
dioxide, un-burnt hydrocarbon, and smoke opacity at the expense of
nitrogen oxides. Carbon monoxide emissions for biodiesel was higher
at maximum output power. It has been found that the combustion
characteristics of cotton seed oil methyl ester closely followed those
of standard petrodiesel. The experimental results suggested that
biodiesel derived from cotton seed oil could be used as a good
substitute to petrodiesel fuel in a conventional diesel without any
modification.
Abstract: Result from the constant dwindle in natural resources,
the alternative way to reduce the costs in our daily life would be urgent
to be found in the near future. As the ancient technique based on the
theory of solar chimney since roman times, the double-skin façade are
simply composed of two large glass panels in purpose of daylighting
and also natural ventilation in the daytime. Double-skin façade is
generally installed on the exterior side of buildings as function as the
window, so there is always a huge amount of passive solar energy the
façade would receive to induce the airflow every sunny day. Therefore,
this article imposes a domestic double-skin window for residential
usage and attempts to improve the volume flow rate inside the cavity
between the panels by the frame geometry design, the installation of
outlet guide plate and the solar energy collection system. Note that the
numerical analyses are applied to investigate the characteristics of flow
field, and the boundary conditions in the simulation are totally based
on the practical experiment of the original prototype. Then we
redesign the prototype from the knowledge of the numerical results
and fluid dynamic theory, and later the experiments of modified
prototype will be conducted to verify the simulation results. The
velocities at the inlet of each case are increase by 5%, 45% and 15%
from the experimental data, and also the numerical simulation results
reported 20% improvement in volume flow rate both for the frame
geometry design and installation of outlet guide plate.
Abstract: Brushless DC motors (BLDC) are widely used in
industrial areas. The BLDC motors are driven either by indirect ACAC
converters or by direct AC-AC converters. Direct AC-AC
converters i.e. matrix converters are used in this paper to drive the
three phase BLDC motor and it eliminates the bulky DC link energy
storage element. A matrix converter converts the AC power supply to
an AC voltage of variable amplitude and variable frequency. A
control technique is designed to generate the switching pulses for the
three phase matrix converter. For the control of speed of the BLDC
motor a separate PI controller and Fuzzy Logic Controller (FLC) are
designed and a hysteresis current controller is also designed for the
control of motor torque. The control schemes are designed and tested
separately. The simulation results of both the schemes are compared
and contrasted in this paper. The results show that the fuzzy logic
control scheme outperforms the PI control scheme in terms of
dynamic performance of the BLDC motor. Simulation results are
validated with the experimental results.
Abstract: The increase in electric power demand in face of
environmental issues has intensified the participation of renewable
energy sources such as photovoltaics, in the energy matrix of various
countries. Due to their operational characteristics, they can generate
time-varying harmonic and inter-harmonic distortions. For this
reason, the application of methods of measurement based on
traditional Fourier analysis, as proposed by IEC 61000-4-7, can
provide inaccurate results. Considering the aspects mentioned herein,
came the idea of the development of this work which aims to present
the results of a comparative evaluation between a methodology
arising from the combination of the Prony method with the Kalman
filter and another method based on the IEC 61000-4-30 and IEC
61000-4-7 standards. Employed in this study were synthetic signals
and data acquired through measurements in a 50kWp photovoltaic
installation.
Abstract: Social networking sites such as Twitter and Facebook
attracts over 500 million users across the world, for those users, their
social life, even their practical life, has become interrelated. Their
interaction with social networking has affected their life forever.
Accordingly, social networking sites have become among the main
channels that are responsible for vast dissemination of different kinds
of information during real time events. This popularity in Social
networking has led to different problems including the possibility of
exposing incorrect information to their users through fake accounts
which results to the spread of malicious content during life events.
This situation can result to a huge damage in the real world to the
society in general including citizens, business entities, and others. In this paper, we present a classification method for detecting the
fake accounts on Twitter. The study determines the minimized set of
the main factors that influence the detection of the fake accounts on
Twitter, and then the determined factors are applied using different
classification techniques. A comparison of the results of these
techniques has been performed and the most accurate algorithm is
selected according to the accuracy of the results. The study has been
compared with different recent researches in the same area; this
comparison has proved the accuracy of the proposed study. We claim
that this study can be continuously applied on Twitter social network
to automatically detect the fake accounts; moreover, the study can be
applied on different social network sites such as Facebook with minor
changes according to the nature of the social network which are
discussed in this paper.
Abstract: During the last decades, a number of food crises such
as Bovine Spongiform Encephalopathy (BSE), Mad-Cow disease,
Dioxin in chicken food, Food-and-Mouth Disease (FMD), have
certainly inflected the reliability of the food industry. Consequently,
the trend in applying different scientific methods of risk assessment
in food safety has obtained more attentions in the academic and
practice. However, lack of practical approach considering entire food
supply chain is tangible in the academic literature. In this regard, this
paper aims to apply risk assessment tool (FMEA) with integration of
Human Factor along the entire supply chain of food production and
test the method in a case study of Diary production, and analyze its
results.
Abstract: In 2009, the new HRM policy was implemented in
Qatar for public sector organisations. The purpose of this research is
to examine how Qatar’s 2009 HRM policy was significant in
influencing employee retention in public organisations. The
conducted study utilised quantitative methodology to analyse the data
on employees’ perceptions of such HRM practices as Performance
Management, Rewards and Promotion, Training and Development
associated with the HRM policy in public organisations in
comparison to semi-private organisations. Employees of seven public
and semi-private organisations filled in the questionnaire based on
the 5-point Likert scale to present quantitative results. The data was
analysed with the correlation and multiple regression statistical
analyses. It was found that Performance Management had the
relationship with Employee Retention, and Rewards and Promotion
influenced Job Satisfaction in public organisations. Relationship
between Job Satisfaction and Employee Retention was also observed.
However, no significant differences were observed in the role of
HRM practices in public and semi-private organisations.
Abstract: A model to predict the plastic zone size for material
under plane stress condition has been developed and verified
experimentally. The developed model is a function of crack size,
crack angle and material property (dislocation density). Simulation
and validation results show that the model developed show good
agreement with experimental results. Samples of low carbon steel
(0.035%C) with included surface crack angles of 45o, 50o, 60o, 70o
and 90o and crack depths of 2mm and 4mm were subjected to low
strain rate between 0.48 x 10-3 s-1 – 2.38 x 10-3 s-1. The mechanical
properties studied were ductility, tensile strength, modulus of
elasticity, yield strength, yield strain, stress at fracture and fracture
toughness. The experimental study shows that strain rate has no
appreciable effect on the size of plastic zone while crack depth and
crack angle plays an imperative role in determining the size of the
plastic zone of mild steel materials.
Abstract: Production fluids are transported from the platform to
tankers or process facilities through transfer pipelines. Water being
one of the heavier phases tends to settle at the bottom of pipelines
especially at low flow velocities and this has adverse consequences
for pipeline integrity. On restart after a shutdown, this could result in
corrosion and issues for process equipment, thus the need to have the
heavier liquid dispersed into the flowing lighter fluid. This study
looked at the flow regime of low water cut and low flow velocity oil
and water flow using conductive film thickness probes in a large
diameter 4-inch pipe to obtain oil and water interface height and the
interface structural velocity. A wide range of 0.1–1.0 m/s oil and
water mixture velocities was investigated for 0.5–5% water cut. Two
fluid model predictions were used to compare with the experimental
results.
Abstract: The 1:1 cocrystal of 2-amino-4-chloro-6-
methylpyrimidine (2A4C6MP) with 4-methylbenzoic acid (4MBA)
(I) has been prepared by slow evaporation method in methanol,
which was crystallized in monoclinic C2/c space group, Z = 8, and a
= 28.431 (2) Å, b = 7.3098 (5) Å, c = 14.2622 (10) Å and β =
109.618 (3)°. The presence of unionized –COOH functional group in
cocrystal I was identified both by spectral methods (1H and 13C
NMR, FTIR) and X-ray diffraction structural analysis. The
2A4C6MP molecule interact with the carboxylic group of the
respective 4MBA molecule through N—H⋯O and O—H⋯N
hydrogen bonds, forming a cyclic hydrogen–bonded motif R2
2(8).
The crystal structure was stabilized by Npyrimidine—H⋯O=C and
C=O—H⋯Npyrimidine types hydrogen bonding interactions.
Theoretical investigations have been computed by HF and density
function (B3LYP) method with 6–311+G (d,p)basis set. The
vibrational frequencies together with 1H and 13C NMR chemical
shifts have been calculated on the fully optimized geometry of
cocrystal I. Theoretical calculations are in good agreement with the
experimental results. Solvent–free formation of this cocrystal I is
confirmed by powder X-ray diffraction analysis.
Abstract: A theoretical study of a humidification
dehumidification solar desalination unit has been carried out to
increase understanding the effect of weather conditions on the unit
productivity. A humidification-dehumidification (HD) solar
desalination unit has been designed to provide fresh water for
population in remote arid areas. It consists of solar water collector
and air collector; to provide the hot water and air to the desalination
chamber. The desalination chamber is divided into humidification
and dehumidification towers. The circulation of air between the two
towers is maintained by the forced convection. A mathematical
model has been formulated, in which the thermodynamic relations
were used to study the flow, heat and mass transfer inside the
humidifier and dehumidifier. The present technique is performed in
order to increase the unit performance. Heat and mass balance has
been done and a set of governing equations has been solved using the
finite difference technique. The unit productivity has been calculated
along the working day during the summer and winter sessions and
has compared with the available experimental results. The average
accumulative productivity of the system in winter has been ranged
between 2.5 to 4 (kg/m2)/day, while the average summer productivity
has been found between 8 to 12 (kg/m2)/day.
Abstract: The floor beams of steel buildings, cold-formed steel
floor joists in particular, often require large web openings, which may
affect their shear capacities. A cost effective way to mitigate the
detrimental effects of such openings is to weld/fasten reinforcements.
A difficulty associated with an experimental investigation to establish
suitable reinforcement schemes for openings in shear zone is that
moment always coexists with the shear, and thus, it is impossible to
create pure shear state in experiments, resulting in moment
influenced results. However, Finite Element Method (FEM) based
analysis can be conveniently used to investigate the pure shear
behaviour of webs including webs with reinforced openings. This
paper presents the details associated with the finite element analysis
of thick/thin-plates (representing the web of hot-rolled steel beam,
and the web of a cold-formed steel member) having a large
reinforced opening. The study considered simply-supported
rectangular plates subjected to in-plane shear loadings until failure
(including post-buckling behaviour). The plate was modelled using
geometrically non-linear quadrilateral shell elements, and non-linear
stress-strain relationship based on experiments. Total Langrangian
with large displacement/small strain formulation was used for such
analyses. The model also considered the initial geometric
imperfections. This study considered three reinforcement schemes,
namely, flat, lip, and angle reinforcements. This paper discusses the
modelling considerations and presents the results associated with the
various reinforcement schemes under consideration.
Abstract: The objective of this work is to carryout critical
comparison of different actuation mechanisms like electrostatic,
thermal, piezoelectric, and magnetic with reference to a micro
cantilever. The relevant parameters like force generated,
displacement are compared in actuation methods. With these results,
helps in choosing the best actuation method for a particular
application. In this study, Comsol/Multiphysics software is used.
Modeling and simulation is done by considering the micro cantilever
of same dimensions as an actuator using all the above mentioned
actuation techniques. In addition to their small size, micro actuators
consume very little power and are capable of accurate results. In this
work, a comparison of actuation mechanisms is done to decide the
efficient system in micro domain.
Abstract: High Performance Liquid Chromatography (HPLC)
method was developed and validated for simultaneous estimation of
6-Gingerol(6G) and 6-Shogaol(6S) in joint pain relief gel containing
ginger extract. The chromatographic separation was achieved by
using C18 column, 150 x 4.6mm i.d., 5μ Luna, mobile phase
containing acetonitrile and water (gradient elution). The flow rate
was 1.0 ml/min and the absorbance was monitored at 282 nm. The
proposed method was validated in terms of the analytical parameters
such as specificity, accuracy, precision, linearity, range, limit of
detection (LOD), limit of quantification (LOQ), and determined
based on the International Conference on Harmonization (ICH)
guidelines. The linearity ranges of 6G and 6S were obtained over 20-
60 and 6-18 μg/ml respectively. Good linearity was observed over the
above-mentioned range with linear regression equation Y= 11016x-
23778 for 6G and Y = 19276x-19604 for 6S (x is concentration of
analytes in μg/ml and Y is peak area). The value of correlation
coefficient was found to be 0.9994 for both markers. The limit of
detection (LOD) and limit of quantification (LOQ) for 6G were
0.8567 and 2.8555 μg/ml and for 6S were 0.3672 and 1.2238 μg/ml
respectively. The recovery range for 6G and 6S were found to be
91.57 to 102.36 % and 84.73 to 92.85 % for all three spiked levels.
The RSD values from repeated extractions for 6G and 6S were 3.43
and 3.09% respectively. The validation of developed method on
precision, accuracy, specificity, linearity, and range were also
performed with well-accepted results.
Abstract: Recently, many users have begun to frequently share
their opinions on diverse issues using various social media. Therefore,
numerous governments have attempted to establish or improve
national policies according to the public opinions captured from
various social media. In this paper, we indicate several limitations of
the traditional approaches to analyze public opinion on science and
technology and provide an alternative methodology to overcome these
limitations. First, we distinguish between the science and technology
analysis phase and the social issue analysis phase to reflect the fact that
public opinion can be formed only when a certain science and
technology is applied to a specific social issue. Next, we successively
apply a start list and a stop list to acquire clarified and interesting
results. Finally, to identify the most appropriate documents that fit
with a given subject, we develop a new logical filter concept that
consists of not only mere keywords but also a logical relationship
among the keywords. This study then analyzes the possibilities for the
practical use of the proposed methodology thorough its application to
discover core issues and public opinions from 1,700,886 documents
comprising SNS, blogs, news, and discussions.