Abstract: The flash memory has many advantages such as low power consumption, strong shock resistance, fast I/O and non-volatility. And it is increasingly used in the mobile storage device. The YAFFS, one of the NAND flash file system, is widely used in the embedded device. However, the existing YAFFS takes long time to mount the file system because it scans whole spare areas in all pages of NAND flash memory. In order to solve this problem, we propose a new content-based flash file system using a mounting time reduction technique. The proposed method only scans partial spare areas of some special pages by using content-based block management. The experimental results show that the proposed method reduces the average mounting time by 87.2% comparing with JFFS2 and 69.9% comparing with YAFFS.
Abstract: In a nuclear reactor Loss of Coolant accident (LOCA)
considers wide range of postulated damage or rupture of pipe in the
heat transport piping system. In the case of LOCA with/without
failure of emergency core cooling system in a Pressurised Heavy
water Reactor, the Pressure Tube (PT) temperature could rise
significantly due to fuel heat up and gross mismatch of the heat
generation and heat removal in the affected channel. The extent and
nature of deformation is important from reactor safety point of view.
Experimental set-ups have been designed and fabricated to simulate
ballooning (radial deformation) of PT for 220 MWe IPHWRs.
Experiments have been conducted by covering the CT by ceramic
fibers and then by submerging CT in water of voided PTs. In both
the experiments, it is observed that ballooning initiates at a
temperature around 665´┐¢C and complete contact between PT and
Caldaria Tube (CT) occurs at around 700´┐¢C approximately. The
strain rate is found to be 0.116% per second. The structural integrity
of PT is retained (no breach) for all the experiments. The PT heatup
is found to be arrested after the contact between PT and CT, thus
establishing moderator acting as an efficient heat sink for IPHWRs.
Abstract: The Mobile Ad-hoc Network (MANET) is a collection of self-configuring and rapidly deployed mobile nodes (routers) without any central infrastructure. Routing is one of the potential issues. Many routing protocols are reported but it is difficult to decide which one is best in all scenarios. In this paper on demand routing protocols DSR and DYMO based on IEEE 802.11 DCF MAC protocol are examined and characteristic summary of these routing protocols is presented. Their performance is analyzed and compared on performance measuring metrics throughput, dropped packets due to non availability of routes, duplicate RREQ generated for route discovery and normalized routing load by varying CBR data traffic load using QualNet 5.0.2 network simulator.
Abstract: This paper presents the region based segmentation method for ultrasound images using local statistics. In this segmentation approach the homogeneous regions depends on the image granularity features, where the interested structures with dimensions comparable to the speckle size are to be extracted. This method uses a look up table comprising of the local statistics of every pixel, which are consisting of the homogeneity and similarity bounds according to the kernel size. The shape and size of the growing regions depend on this look up table entries. The algorithms are implemented by using connected seeded region growing procedure where each pixel is taken as seed point. The region merging after the region growing also suppresses the high frequency artifacts. The updated merged regions produce the output in formed of segmented image. This algorithm produces the results that are less sensitive to the pixel location and it also allows a segmentation of the accurate homogeneous regions.
Abstract: The highly nonlinear characteristics of drying
processes have prompted researchers to seek new nonlinear control
solutions. However, the relation between the implementation
complexity, on-line processing complexity, reliability control
structure and controller-s performance is not well established. The
present paper proposes high performance nonlinear fuzzy controllers
for a real-time operation of a drying machine, being developed under
a consistent match between those issues. A PCI-6025E data
acquisition device from National Instruments® was used, and the
control system was fully designed with MATLAB® / SIMULINK
language. Drying parameters, namely relative humidity and
temperature, were controlled through MIMOs Hybrid Bang-bang+PI
(BPI) and Four-dimensional Fuzzy Logic (FLC) real-time-based
controllers to perform drying tests on biological materials. The
performance of the drying strategies was compared through several
criteria, which are reported without controllers- retuning. Controllers-
performance analysis has showed much better performance of FLC
than BPI controller. The absolute errors were lower than 8,85 % for
Fuzzy Logic Controller, about three times lower than the
experimental results with BPI control.
Abstract: The characteristics of fluid flow and phase separation
in an oil-water separator were numerically analysed as part of the
work presented herein. Simulations were performed for different
velocities and droplet diameters, and the way this parameters can
influence the separator geometry was studied.
The simulations were carried out using the software package
Fluent 6.2, which is designed for numerical simulation of fluid flow
and mass transfer. The model consisted of a cylindrical horizontal
separator. A tetrahedral mesh was employed in the computational
domain. The condition of two-phase flow was simulated with the
two-fluid model, taking into consideration turbulence effects using
the k-ε model.
The results showed that there is a strong dependency of phase
separation on mixture velocity and droplet diameter. An increase in
mixture velocity will bring about a slow down in phase separation
and as a consequence will require a weir of greater height. An
increase in droplet diameter will produce a better phase separation.
The simulations are in agreement with results reported in literature
and show that CFD can be a useful tool in studying a horizontal oilwater
separator.
Abstract: Today, computer systems are more and more complex and support growing security risks. The security managers need to find effective security risk assessment methodologies that allow modeling well the increasing complexity of current computer systems but also maintaining low the complexity of the assessment procedure. This paper provides a brief analysis of common security risk assessment methodologies leading to the selection of a proper methodology to fulfill these requirements. Then, a detailed analysis of the most effective methodology is accomplished, presenting numerical examples to demonstrate how easy it is to use.
Abstract: The paper outlines the drivers behind the movement
from products to solutions in the Hi-Tech Business-to-Business
markets. The paper lists out the challenges in enabling the
transformation from products to solutions and also attempts to explore
strategic and operational recommendations based on the authors-
factual experiences with Japanese Hi-tech manufacturing
organizations. Organizations in the Hi-Tech Business-to-Business
markets are increasingly being compelled to move to a solutions model
from the conventional products model. Despite the added complexity
of solutions, successful technology commercialization can be achieved
by making prudent choices in defining a relevant solutions model, by
backing the solution model through appropriate organizational design,
and by overhauling the new product development process and
supporting infrastructure.
Abstract: Multimedia distributed systems deal with heterogeneous
data, such as texts, images, graphics, video and audio. The specification
of temporal relations among different data types and distributed
sources is an open research area. This paper proposes a fully
distributed synchronization model to be used in multimedia systems.
One original aspect of the model is that it avoids the use of a common
reference (e.g. wall clock and shared memory). To achieve this, all
possible multimedia temporal relations are specified according to
their causal dependencies.
Abstract: The results obtained after incorporating the competence “creativity" to the subject Technical Drawing of the first course of the Degree in Forestry, Technical University of Madrid, are presented in this study.At first, learning activities which could serve two functions at the same time -developing students- creativity and developing other specific competences of the subject- were considered. Besides, changes in the assessment procedure were made and a method which analyzes two aspects of the assessment of the competence creativity was established. On the one hand, the products are evaluated by analyzing the outcomes obtained by students in the essays suggested and by establishing a parameter to assess the creativity expressed in those essays. On the other, an assessment of the student is directly carried out through a psychometric test which has been previously chosen by the team.Moreover, these results can be applied to similar or could be of general application.
Abstract: Chicken feathers were used as biosorbent for Pb
removal from aqueous solution. In this paper, the kinetics and
equilibrium studies at several pH, temperature, and metal
concentration values are reported. For tested conditions, the Pb
sorption capacity of this poultry waste ranged from 0.8 to 8.3 mg/g.
Optimal conditions for Pb removal by chicken feathers have been
identified. Pseudo-first order and pseudo-second order equations
were used to analyze the experimental data. In addition, the sorption
isotherms were fitted to classical Langmuir and Freundlich models.
Finally, thermodynamic parameters for the sorption process have
been determined. In summary, the results showed that chicken
feathers are an alternative and promising sorbent for the treatment of
effluents polluted by Pb ions.
Abstract: Design, as an area of knowledge, is subject to changes that affect it through different approaches, both theoretical and practical; its include matters related with responsibility, environment, social worries, and things alike. Commensurately, such contemporary aspects open room for social initiatives. This scenario begins to be looked at, especially in creative communities. Such proposal for a systemic approach of design is seen as a way to involve the stakeholders in the processes of investigation and of social innovation, which can decisively contribute for the development of traditional local communities. As a theoretical basis for the research, this paper outlines some especial features of design and social innovation, in their particular and in their complementary aspects, as well as in the way they relate with each other.
Abstract: DNA microarrays allow the measurement of expression levels for a large number of genes, perhaps all genes of an organism, within a number of different experimental samples. It is very much important to extract biologically meaningful information from this huge amount of expression data to know the current state of the cell because most cellular processes are regulated by changes in gene expression. Association rule mining techniques are helpful to find association relationship between genes. Numerous association rule mining algorithms have been developed to analyze and associate this huge amount of gene expression data. This paper focuses on some of the popular association rule mining algorithms developed to analyze gene expression data.
Abstract: CIM is the standard formalism for modeling management
information developed by the Distributed Management Task
Force (DMTF) in the context of its WBEM proposal, designed to
provide a conceptual view of the managed environment. In this
paper, we propose the inclusion of formal knowledge representation
techniques, based on Description Logics (DLs) and the Web Ontology
Language (OWL), in CIM-based conceptual modeling, and then we
examine the benefits of such a decision. The proposal is specified as a
CIM metamodel level mapping to a highly expressive subset of DLs
capable of capturing all the semantics of the models. The paper shows
how the proposed mapping can be used for automatic reasoning
about the management information models, as a design aid, by means
of new-generation CASE tools, thanks to the use of state-of-the-art
automatic reasoning systems that support the proposed logic and use
algorithms that are sound and complete with respect to the semantics.
Such a CASE tool framework has been developed by the authors and
its architecture is also introduced. The proposed formalization is not
only useful at design time, but also at run time through the use of
rational autonomous agents, in response to a need recently recognized
by the DMTF.
Abstract: Software estimation accuracy is among the greatest
challenges for software developers. This study aimed at building and
evaluating a neuro-fuzzy model to estimate software projects
development time. The forty-one modules developed from ten
programs were used as dataset. Our proposed approach is compared
with fuzzy logic and neural network model and Results show that the
value of MMRE (Mean of Magnitude of Relative Error) applying
neuro-fuzzy was substantially lower than MMRE applying fuzzy
logic and neural network.
Abstract: Through the time, the higher education has changed
the learning system since mother tongue to bilingual, and in this new
century has been coming develop a multilingual education. All as
part of globalization process of the countries and the education.
Nevertheless, this change only has been effectively in countries of the
first world, the rest have been lagging. Therefore, these countries
require strengthen their higher education systems through models that
give way to multilingual and bilingual education. In this way, shows
a new model adapted from a systemic form to allow a higher
bilingual and multilingual education in Latin America. This
systematization aims to increase the skills and competencies
student’s, decrease the time learning of a second tongue, add to
multilingualism in the American Latin Universities, also, contribute
to position the region´s countries in a better global status, and
stimulate the development of new research in this area.
Abstract: The objective of this study was to develop and compare alternative prediction equations of lean meat proportion (LMP) of lamb carcasses. Forty (40) male lambs, 22 of Churra Galega Bragançana Portuguese local breed and 18 of Suffolk breed were used. Lambs were slaughtered, and carcasses weighed approximately 30 min later in order to obtain hot carcass weight (HCW). After cooling at 4º C for 24-h a set of seventeen carcass measurements was recorded. The left side of carcasses was dissected into muscle, subcutaneous fat, inter-muscular fat, bone, and remainder (major blood vessels, ligaments, tendons, and thick connective tissue sheets associated with muscles), and the LMP was evaluated as the dissected muscle percentage. Prediction equations of LMP were developed, and fitting quality was evaluated through the coefficient of determination of estimation (R2 e) and standard error of estimate (SEE). Models validation was performed by k-fold crossvalidation and the coefficient of determination of prediction (R2 p) and standard error of prediction (SEP) were computed. The BT2 measurement was the best single predictor and accounted for 37.8% of the LMP variation with a SEP of 2.30%. The prediction of LMP of lamb carcasses can be based simple models, using as predictors the HCW and one fat thickness measurement.
Abstract: The Bangalore City is facing the acute problem of
pollution in the atmosphere due to the heavy increase in the traffic
and developmental activities in recent years. The present study is an
attempt in the direction to assess trend of the ambient air quality
status of three stations, viz., AMCO Batteries Factory, Mysore Road,
GRAPHITE INDIA FACTORY, KHB Industrial Area, Whitefield
and Ananda Rao Circle, Gandhinagar with respect to some of the
major criteria pollutants such as Total Suspended particular matter
(SPM), Oxides of nitrogen (NOx), and Oxides of sulphur (SO2). The
sites are representative of various kinds of growths viz., commercial,
residential and industrial, prevailing in Bangalore, which are
contributing to air pollution. The concentration of Sulphur Dioxide
(SO2) at all locations showed a falling trend due to use of refined
petrol and diesel in the recent years. The concentration of Oxides of
nitrogen (NOx) showed an increasing trend but was within the
permissible limits. The concentration of the Suspended particular
matter (SPM) showed the mixed trend. The correlation between
model and observed values is found to vary from 0.4 to 0.7 for SO2,
0.45 to 0.65 for NOx and 0.4 to 0.6 for SPM. About 80% of data is
observed to fall within the error band of ±50%. Forecast test for the
best fit models showed the same trend as actual values in most of the
cases. However, the deviation observed in few cases could be
attributed to change in quality of petro products, increase in the
volume of traffic, introduction of LPG as fuel in many types of
automobiles, poor condition of roads, prevailing meteorological
conditions, etc.
Abstract: In a particular case of behavioural model reduction by ANNs, a validity domain shortening has been found. In mechanics, as in other domains, the notion of validity domain allows the engineer to choose a valid model for a particular analysis or simulation. In the study of mechanical behaviour for a cantilever beam (using linear and non-linear models), Multi-Layer Perceptron (MLP) Backpropagation (BP) networks have been applied as model reduction technique. This reduced model is constructed to be more efficient than the non-reduced model. Within a less extended domain, the ANN reduced model estimates correctly the non-linear response, with a lower computational cost. It has been found that the neural network model is not able to approximate the linear behaviour while it does approximate the non-linear behaviour very well. The details of the case are provided with an example of the cantilever beam behaviour modelling.
Abstract: The article is about government programs and projects
and their description which are aimed at improving the socioeconomic
situation in the Republic of Kazakhstan. A brief historical
overview, as well as information about current socio-economic,
political and transitional contexts of the country are provided. Two
theories were described in the article to inform this descriptive study.
According to the United Nation's Development Reports for 2005 and
2011, the country's human development index (HDI) rose by several
points despite the socio-economic and political imbalances taking
place in the republic since it gained its independence in 1991. It is
stated in the article that government support programs are one of the
crucial factors that increase the population welfare which in its turn
may lead to reduction of social crisis processes in the country.