Abstract: Many real-world optimization problems involve multiple conflicting objectives and the use of evolutionary algorithms to solve the problems has attracted much attention recently. This paper investigates the application of multi-objective optimization technique for the design of a Thyristor Controlled Series Compensator (TCSC)-based controller to enhance the performance of a power system. The design objective is to improve both rotor angle stability and system voltage profile. A Genetic Algorithm (GA) based solution technique is applied to generate a Pareto set of global optimal solutions to the given multi-objective optimisation problem. Further, a fuzzy-based membership value assignment method is employed to choose the best compromise solution from the obtained Pareto solution set. Simulation results are presented to show the effectiveness and robustness of the proposed approach.
Abstract: The main purpose of the study was to determine whether students- interpretation achievement differed with the use of various multimedia presentation types. Four groups of students, text only (T), audio only (A), text and audio (TA), text and image (TI), were arranged and they were presented the same story via different types of multimedia presentations. Inference achievement was measured by a critical thinking inference test. Higher mean scores for the TA group compared to the other three groups were found. Also when compared pairwise, interpretation achievement of the TA group differed significantly from scores of the T and TI groups. These differences were interpreted with the increased cognitive load. Increased cognitive load for the TA group may have invited students to put more effort into comprehending the text, thus resulting in better test scores. Findings of the study can be seen as a sign of the importance of learning situations and learning outcomes in multimedia-supported learning environments and may have practical benefits for instructional designers.
Abstract: Absorptive characteristics of polyaniline synthesized
in mixture of water and acetonitrile in 50/50 volume ratio was
studied. Synthesized polyaniline in powder shape is used as an
adsorbent to remove toxic hexavalent chromium from aqueous
solutions. Experiments were conducted in batch mode with different
variables such as agitation time, solution pH and initial concentration
of hexavalent chromium. Removal mechanism is the combination of
surface adsorption and reduction. The equilibrium time for removal
of Cr(T) and Cr(VI) was about 2 and 10 minutes respectively. The
optimum pH for total chromium removal occurred at pH 7 and
maximum hexavalent chromium removal took place under acidic
condition at pH 3. Investigating the isothermal characteristics showed
that the equilibrium adsorption data fitted both Freundlich-s and
Langmuir-s isotherms. The maximum adsorption of chromium was
calculated 36.1 mg/g for polyaniline
Abstract: With the development of ubiquitous computing,
current user interaction approaches with keyboard, mouse and pen
are not sufficient. Due to the limitation of these devices the useable
command set is also limited. Direct use of hands as an input device is
an attractive method for providing natural Human Computer
Interaction which has evolved from text-based interfaces through 2D
graphical-based interfaces, multimedia-supported interfaces, to fully
fledged multi-participant Virtual Environment (VE) systems.
Imagine the human-computer interaction of the future: A 3Dapplication
where you can move and rotate objects simply by moving
and rotating your hand - all without touching any input device. In this
paper a review of vision based hand gesture recognition is presented.
The existing approaches are categorized into 3D model based
approaches and appearance based approaches, highlighting their
advantages and shortcomings and identifying the open issues.
Abstract: Nowadays, new home appliances and office appliances
have been developed that communicate with users through the
Internet, for remote monitor and remote control. However, developments
and sales of these new appliances are just started, then,
many products in our houses and offices do not have these useful
functions. In few years, we add these new functions to the outlet,
it means multifunctional electrical power socket plug adapter. The
outlet measure power consumption of connecting appliances, and it
can switch power supply to connecting appliances, too. Using this
outlet, power supply of old appliances can be control and monitor.
And we developed the interface system using web browser to operate
it from users[1]. But, this system need to set up LAN cables between
outlets and so on. It is not convenience that cables around rooms. In
this paper, we develop the system that use wireless mobile ad hoc
network instead of wired LAN to communicate with the outlets.
Abstract: The Petri net tool INA is a well known tool by the
Petri net community. However, it lacks a graphical environment to
cerate and analyse INA models. Building a modelling tool for the
design and analysis from scratch (for INA tool for example) is
generally a prohibitive task. Meta-Modelling approach is useful to
deal with such problems since it allows the modelling of the
formalisms themselves. In this paper, we propose an approach based
on the combined use of Meta-modelling and Graph Grammars to
automatically generate a visual modelling tool for INA for analysis
purposes. In our approach, the UML Class diagram formalism is
used to define a meta-model of INA models. The meta-modelling
tool ATOM3 is used to generate a visual modelling tool according to
the proposed INA meta-model. We have also proposed a graph
grammar to automatically generate INA description of the
graphically specified Petri net models. This allows the user to avoid
the errors when this description is done manually. Then the INA tool
is used to perform the simulation and the analysis of the resulted INA
description. Our environment is illustrated through an example.
Abstract: The purpose of this paper is to present the fuzzy contraction
properties of the Hutchinson-Barnsley operator on the fuzzy
hyperspace with respect to the Hausdorff fuzzy metrics. Also we
discuss about the relationships between the Hausdorff fuzzy metrics
on the fuzzy hyperspaces. Our theorems generalize and extend some
recent results related with Hutchinson-Barnsley operator in the metric
spaces.
Abstract: MRAM technology provides a combination of fast
access time, non-volatility, data retention and endurance. While a
growing interest is given to two-terminal Magnetic Tunnel Junctions
(MTJ) based on Spin-Transfer Torque (STT) switching as the
potential candidate for a universal memory, its reliability is
dramatically decreased because of the common writing/reading path.
Three-terminal MTJ based on Spin-Orbit Torque (SOT) approach
revitalizes the hope of an ideal MRAM. It can overcome the
reliability barrier encountered in current two-terminal MTJs by
separating the reading and the writing path. In this paper, we study
two possible writing schemes for the SOT-MTJ device based on
recently fabricated samples. While the first is based on precessional
switching, the second requires the presence of permanent magnetic
field. Based on an accurate Verilog-A model, we simulate the two
writing techniques and we highlight advantages and drawbacks of
each one. Using the second technique, pioneering logic circuits based
on the three-terminal architecture of the SOT-MTJ described in this
work are under development with preliminary attractive results.
Abstract: A new target detection technique is presented in this
paper for the identification of small boats in coastal surveillance. The
proposed technique employs an adaptive progressive thresholding (APT) scheme to first process the given input scene to separate any
objects present in the scene from the background. The preprocessing
step results in an image having only the foreground objects, such as
boats, trees and other cluttered regions, and hence reduces the search
region for the correlation step significantly. The processed image is then fed to the shifted phase-encoded fringe-adjusted joint transform
correlator (SPFJTC) technique which produces single and delta-like
correlation peak for a potential target present in the input scene. A
post-processing step involves using a peak-to-clutter ratio (PCR) to determine whether the boat in the input scene is authorized or unauthorized. Simulation results are presented to show that the
proposed technique can successfully determine the presence of an authorized boat and identify any intruding boat present in the given input scene.
Abstract: Optical properties of sputter-deposited ZnS thin films
were investigated as potential replacements for CBD(chemical bath
deposition) CdS buffer layers in the application of CIGS solar cells.
ZnS thin films were fabricated on glass substrates at RT, 150oC, 200oC,
and 250oC with 50 sccm Ar gas using an RF magnetron sputtering
system. The crystal structure of the thin film is found to be zinc blende
(cubic) structure. Lattice parameter of ZnS is slightly larger than CdS
on the plane and thus better matched with that of CIGS. Within a
400-800 nm wavelength region, the average transmittance was larger
than 75%. When the deposition temperature of the thin film was
increased, the blue shift phenomenon was enhanced. Band gap energy
of the ZnS thin film tended to increase as the deposition temperature
increased. ZnS thin film is a promising material system for the CIGS
buffer layer, in terms of ease of processing, low cost, environmental
friendliness, higher transparency, and electrical properties
Abstract: Measurement of the quality of image compression is important for image processing application. In this paper, we propose an objective image quality assessment to measure the quality of gray scale compressed image, which is correlation well with subjective quality measurement (MOS) and least time taken. The new objective image quality measurement is developed from a few fundamental of objective measurements to evaluate the compressed image quality based on JPEG and JPEG2000. The reliability between each fundamental objective measurement and subjective measurement (MOS) is found. From the experimental results, we found that the Maximum Difference measurement (MD) and a new proposed measurement, Structural Content Laplacian Mean Square Error (SCLMSE), are the suitable measurements that can be used to evaluate the quality of JPEG200 and JPEG compressed image, respectively. In addition, MD and SCLMSE measurements are scaled to make them equivalent to MOS, given the rate of compressed image quality from 1 to 5 (unacceptable to excellent quality).
Abstract: The substrate heater designed for this investigation is a front side substrate heating system. It consists of 10 conventional tungsten halogen lamps and an aluminum reflector, total input electrical power of 5 kW. The substrate is heated by means of a radiation from conventional tungsten halogen lamps directed to the substrate through a glass window. This design allows easy replacement of the lamps and maintenance of the system. Within 2 to 6 minutes the substrate temperature reaches 500 to 830 C by varying the vertical distance between the glass window and the substrate holder. Moreover, the substrate temperature can be easily controlled by controlling the input power to the system. This design gives excellent opportunity to deposit many deferent films at deferent temperatures in the same deposition time. This substrate heater was successfully used for Chemical Vapor Deposition (CVD) of many thin films, such as Silicon, iron, etc.
Abstract: The study investigated the effects of Teaching Games
for Understanding approach on students ‘cognitive learning outcome.
The study was a quasi-experimental non-equivalent pretest-posttest
control group design whereby 10 year old primary school students
(n=72) were randomly assigned to an experimental and a control
group. The experimental group students were exposed with TGfU
approach and the control group with the Traditional Skill approach of
handball game. Game Performance Assessment Instrument (GPAI)
was used to measure students' tactical understanding and decision
making in 3 versus 3 handball game situations. Analysis of
covariance (ANCOVA) was used to analyze the data. The results
reveal that there was a significant difference between the TGfU
approach group and the traditional skill approach group students on
post test score (F (1, 69) = 248.83, p < .05). The findings of this
study suggested the importance of TGfU approach to improve
primary students’ tactical understanding and decision making in
handball game.
Abstract: Heat transfer from two cam shape cylinder in side-byside
arrangement had been studied numerically.
The transverse gap between the centers of cylinders (T) is allowed
to vary to change the pitch ratio (T/Deq). The equivalent diameter of
the cylinder (Deq) is 27.6 mm and pitch ratio varies in range of
1≤T/Deq≤3. The Reynolds numbers based on equivalent circular
cylinder are within 50≤ Reeq≤150. Results show that Nusselt number
of cylinders increases about 1 to 36 percent when pitch ratio
increases from 1 to 3.
Abstract: The overall objective of this research is a strain
improvement technology for efficient pectinase production. A novel
cells cultivation technology by immobilization of fungal cells has
been studied in long time continuous fermentations. Immobilization
was achieved by using of new material for absorption of stores of
immobilized cultures which was for the first time used for
immobilization of microorganisms. Effects of various conditions of
nitrogen and carbon nutrition on the biosynthesis of pectolytic
enzymes in Aspergillus awamori 1-8 strain were studied. Proposed
cultivation technology along with optimization of media components
for pectinase overproduction led to increased pectinase productivity
in Aspergillus awamori 1-8 from 7 to 8 times. Proposed technology
can be applied successfully for production of major industrial
enzymes such as α-amylase, protease, collagenase etc.
Abstract: In mechanical and environmental engineering, mixed
convection is a frequently encountered thermal fluid phenomenon
which exists in atmospheric environment, urban canopy flows, ocean
currents, gas turbines, heat exchangers, and computer chip cooling
systems etc... . This paper deals with a numerical investigation of
mixed convection in a vertical heated channel. This flow results from
the mixing of the up-going fluid along walls of the channel with the
one issued from a flat nozzle located in its entry section. The fluiddynamic
and heat-transfer characteristics of vented vertical channels
are investigated for constant heat-flux boundary conditions, a
Rayleigh number equal to 2.57 1010, for two jet Reynolds number
Re=3 103 and 2104 and the aspect ratio in the 8-20 range. The system
of governing equations is solved with a finite volumes method and an
implicit scheme. The obtained results show that the turbulence and
the jet-wall interaction activate the heat transfer, as does the drive of
ambient air by the jet. For low Reynolds number Re=3 103, the
increase of the aspect Ratio enhances the heat transfer of about 3%,
however; for Re=2 104, the heat transfer enhancement is of about
12%. The numerical velocity, pressure and temperature fields are
post-processed to compute the quantities of engineering interest such
as the induced mass flow rate, and average Nusselt number, in terms
of Rayleigh, Reynolds numbers and dimensionless geometric
parameters are presented.
Abstract: In-place sorting algorithms play an important role in many fields such as very large database systems, data warehouses, data mining, etc. Such algorithms maximize the size of data that can be processed in main memory without input/output operations. In this paper, a novel in-place sorting algorithm is presented. The algorithm comprises two phases; rearranging the input unsorted array in place, resulting segments that are ordered relative to each other but whose elements are yet to be sorted. The first phase requires linear time, while, in the second phase, elements of each segment are sorted inplace in the order of z log (z), where z is the size of the segment, and O(1) auxiliary storage. The algorithm performs, in the worst case, for an array of size n, an O(n log z) element comparisons and O(n log z) element moves. Further, no auxiliary arithmetic operations with indices are required. Besides these theoretical achievements of this algorithm, it is of practical interest, because of its simplicity. Experimental results also show that it outperforms other in-place sorting algorithms. Finally, the analysis of time and space complexity, and required number of moves are presented, along with the auxiliary storage requirements of the proposed algorithm.
Abstract: This paper presents an exact solution and a finite element method (FEM) for a Piezoceramic Rod under static load. The cylindrical rod is made from polarized ceramics (piezoceramics) with axial poling. The lateral surface of the rod is traction-free and is unelectroded. The two end faces are under a uniform normal traction. Electrically, the two end faces are electroded with a circuit between the electrodes, which can be switched on or off. Two cases of open and shorted electrodes (short circuit and open circuit) will be considered. Finally, a finite element model will be used to compare the results with an exact solution. The study uses ABAQUS (v.6.7) software to derive the finite element model of the ceramic rod.
Abstract: All Text processing systems allow their users to
search a pattern of string from a given text. String matching is
fundamental to database and text processing applications. Every text
editor must contain a mechanism to search the current document for
arbitrary strings. Spelling checkers scan an input text for words in the
dictionary and reject any strings that do not match. We store our
information in data bases so that later on we can retrieve the same
and this retrieval can be done by using various string matching
algorithms. This paper is describing a new string matching algorithm
for various applications. A new algorithm has been designed with the
help of Rabin Karp Matcher, to improve string matching process.
Abstract: One of the best ways for achievement of conventional
vehicle changing to hybrid case is trustworthy simulation result and
using of driving realities. For this object, in this paper, at first sevendegree-
of-freedom dynamical model of vehicle will be shown. Then
by using of statically model of engine, gear box, clutch, differential,
electrical machine and battery, the hybrid automobile modeling will
be down and forward simulation of vehicle for pedals to wheels
power transformation will be obtained. Then by design of a fuzzy
controller and using the proper rule base, fuel economy and
regenerative braking will be marked. Finally a series of
MATLAB/SIMULINK simulation results will be proved the
effectiveness of proposed structure.