Abstract: This paper presents the generation of bipolar square
wave pulses with characteristics that are suitable for liquid food
sterilization using a Cascaded H-bridge Multilevel Inverter (CHMI).
Bipolar square waves pulses have been reported as stable for a
longer time during the sterilization process with minimum heat
emission and increased efficiency. The CHMI allows the system to
produce bipolar square wave pulses and yielding high output voltage
without using a transformer while fulfilling the pulse requirements
for effective liquid food sterilization. This in turn can reduce power
consumption and cost of the overall liquid food sterilization system.
The simulation results have shown that pulses with peak output
voltage of 2.4 kV, pulse width of between 1 2s and 1 ms at
frequencies of 50 Hz and 100 Hz can be generated by a 7-level
CHMI. Results from the experimental set-up based on a 5-level
CHMI has indicated the potential of the proposed circuit in
producing bipolar square wave output pulses with peak values that
depends on the DC source level supplied to the CHMI modules,
pulse width of between 12.5 2s and 1 ms at frequencies of 50 Hz
and 100 Hz.
Abstract: The seeds of cotton (Gossypium hirsutum) fall among the lesser known oil seeds. Cottonseeds are not normally consumed in their natural state due to their gossypol content, an antinutrient. The effect of processing on the sensory characteristics and chemical composition of cottonseed and its extract was studied by subjecting the cottonseed extract to heat treatment (boiling) and the cottonseed to fermentation. The cottonseed extract was boiled using the open pot and the pressure pot for 30 minutes respectively. The fermentation of the cottonseed was carried out for 6 days with samples withdrawn at intervals of 2 days. The extract and fermented samples were subjected to chemical analysis and sensory evaluated for colour, aroma, taste, mouth feel, appearance and overallacceptability. The open pot sample was more preferred. Fermentation for 6 days resulted into a significant reduction in gossypol level of the cottonseed; however, sample fermented for 2 days was most preferred.
Abstract: In this study, a frame work for verification of famous seismic codes is utilized. To verify the seismic codes performance, damage quantity of RC frames is compared with the target performance. Due to the randomness property of seismic design and earthquake loads excitation, in this paper, fragility curves are developed. These diagrams are utilized to evaluate performance level of structures which are designed by the seismic codes. These diagrams further illustrate the effect of load combination and reduction factors of codes on probability of damage exceedance. Two types of structures; very high important structures with high ductility and medium important structures with intermediate ductility are designed by different seismic codes. The Results reveal that usually lower damage ratio generate lower probability of exceedance. In addition, the findings indicate that there are buildings with higher quantity of bars which they have higher probability of damage exceedance. Life-cycle cost analysis utilized for comparison and final decision making process.
Abstract: Since the last two decades, container transportation
system has been faced under increasing development. This fact
shows the importance of container transportation system as a key role
of container terminals to link between sea and land. Therefore, there
is a continuous need for the optimal use of equipment and facilities in
the ports. Regarding the complex structure of container ports, this
paper presents a simulation model that compares tow storage
strategies for storing containers in the yard. For this purpose, we
considered loading and unloading norm as an important criterion to
evaluate the performance of Shahid Rajaee container port. By
analysing the results of the model, it will be shown that using
marshalling yard policy instead of current storage system has a
significant effect on the performance level of the port and can
increase the loading and unloading norm up to 14%.
Abstract: The study examined the influence of pay differentials on employee retention in the State Colleges of Education in the South-South Region of Nigeria. 275 subjects drawn from members of the wage negotiating teams in the Colleges were administered questionnaires constructed for study. Analysis of Variance revealed that the observed pay differentials significantly influenced retainership, f(5,269 = 6.223, P< 0.05). However, the Multiple Classification Analysis and Post-Hoc test indicated that employees in two of the Colleges with slightly lower and higher pay levels may probably remain with their employers while employees in other Colleges with the least and highest pay levels suggested quitting. Based on these observations, the influence of pay on employee retention seems inconclusive. Generally, employees in the colleges studied are dissatisfied with current pay levels. Management should confront these challenges by improving pay packages to encourage employees to remain and be dedicated to duty.
Abstract: Monitored 3-Dimensional (3D) video experience can be utilized as “feedback information” to fine tune the service parameters for providing a better service to the demanding 3D service customers. The 3D video experience which includes both video quality and depth perception is influenced by several contextual and content related factors (e.g., ambient illumination condition, content characteristics, etc) due to the complex nature of the 3D video. Therefore, effective factors on this experience should be utilized while assessing it. In this paper, structural information of the depth map sequences of the 3D video is considered as content related factor effective on the depth perception assessment. Cartoon-like filter is utilized to abstract the significant depth levels in the depth map sequences to determine the structural information. Moreover, subjective experiments are conducted using 3D videos associated with cartoon-like depth map sequences to investigate the effectiveness of ambient illumination condition, which is a contextual factor, on depth perception. Using the knowledge gained through this study, 3D video experience metrics can be developed to deliver better service to the 3D video service users.
Abstract: A synchronous network-on-chip using wormhole packet switching
and supporting guaranteed-completion best-effort with low-priority (LP)
and high-priority (HP) wormhole packet delivery service is presented in
this paper. Both our proposed LP and HP message services deliver a good
quality of service in term of lossless packet completion and in-order message
data delivery. However, the LP message service does not guarantee minimal
completion bound. The HP packets will absolutely use 100% bandwidth of
their reserved links if the HP packets are injected from the source node with
maximum injection. Hence, the service are suitable for small size messages
(less than hundred bytes). Otherwise the other HP and LP messages, which
require also the links, will experience relatively high latency depending on the
size of the HP message. The LP packets are routed using a minimal adaptive
routing, while the HP packets are routed using a non-minimal adaptive routing
algorithm. Therefore, an additional 3-bit field, identifying the packet type,
is introduced in their packet headers to classify and to determine the type
of service committed to the packet. Our NoC prototypes have been also
synthesized using a 180-nm CMOS standard-cell technology to evaluate the
cost of implementing the combination of both services.
Abstract: Software-as-a-Service (SaaS) is a form of cloud
computing that relieves the user of the burden of hardware and
software installation and management. SaaS can be used at the course
level to enhance curricula and student experience. When cloud
computing and SaaS are included in educational literature, the focus
is typically on implementing administrative functions. Yet, SaaS can
make more immediate and substantial contributions to the technical
course content in educational offerings. This paper explores cloud
computing and SaaS, provides examples, reports on experiences
using SaaS to offer specialized software in courses, and analyzes the
advantages and disadvantages of using SaaS at the course level. The
paper contributes to the literature in higher education by analyzing
the major technical concepts, potential, and constraints for using
SaaS to deliver specialized software at the course level. Further it
may enable more educators and students to benefit from this
emerging technology.
Abstract: Microarrays technique allows the simultaneous measurements of the expression levels of thousands of mRNAs. By mining this data one can identify the dynamics of the gene expression time series. By recourse of principal component analysis, we uncover the circadian rhythmic patterns underlying the gene expression profiles from Cyanobacterium Synechocystis. We applied PCA to reduce the dimensionality of the data set. Examination of the components also provides insight into the underlying factors measured in the experiments. Our results suggest that all rhythmic content of data can be reduced to three main components.
Abstract: In this study, we examined gender differences in: (1) a
flexible remembering task, that asked for episodic memory decisions
at an item-specific versus category-based level, and (2) the retrieval
specificity of autobiographical memory during free recall.
Differences favouring women were found on both measures.
Furthermore, a significant association was observed, across gender
groups, between level of specificity in the autobiographical memory
interview and sensitivity to gist on the flexible remembering task.
These results suggest that similar cognitive processes may partially
contribute to both the ability for specific autobiographical recall and
the capacity for inhibition of gist-information on the flexible
remembering task.
Abstract: Cylindrical concrete reservoirs are appropriate choice
for storing liquids as water, oil and etc. By using of the pre-cast
concrete reservoirs instead of the in-situ constructed reservoirs, the
speed and precision of the construction would considerably increase.
In this construction method, wall and roof panels would make in
factory with high quality materials and precise controlling. Then,
pre-cast wall and roof panels would carry out to the construction site
for assembling. This method has a few faults such as: the existing
weeks in connection of wall panels together and wall panels to
foundation. Therefore, these have to be resisted under applied loads
such as seismic load. One of the innovative methods which was
successfully applied for seismic retrofitting of numerous pre-cast
cylindrical water reservoirs in New Zealand, using of the high tensile
cables around the reservoirs and post-tensioning them. In this paper,
analytical modeling of wall and roof panels and post-tensioned
cables are carried out with finite element method and the effect of
height to diameter ratio, post-tensioning force value, liquid level in
reservoir, installing position of tendons on seismic response of
reservoirs are investigated.
Abstract: The performances of small and medium enterprises
have stagnated in the last two decades. This has mainly been due to
the emergence of HIV / Aids. The disease has had a detrimental
effect on the general economy of the country leading to morbidity
and mortality of the Kenyan workforce in their primary age. The
present study sought to establish the economic impact of HIV / Aids
on the micro-enterprise development in Obunga slum – Kisumu, in
terms of production loss, increasing labor related cost and to establish
possible strategies to address the impact of HIV / Aids on microenterprises.
The study was necessitated by the observation that most
micro-enterprises in the slum are facing severe economic and social
crisis due to the impact of HIV / Aids, they get depleted and close
down within a short time due to death of skilled and experience
workforce. The study was carried out between June 2008 and June
2009 in Obunga slum. Data was subjected to computer aided
statistical analysis that included descriptive statistic, chi-squared and
ANOVA techniques. Chi-squared analysis on the micro-enterprise
owners opinion on the impact of HIV / Aids on depletion of microenterprise
compared to other diseases indicated high levels of the
negative effects of the disease at significance levels of P
Abstract: We report here, the results of molecular dynamics
simulation of p-doped (Ga-face)GaN over n-doped (Siface)(
0001)4H-SiC hetero-epitaxial material system with one-layer
each of Ga-flux and (Al-face)AlN, as the interface materials, in the
form of, the total Density of States (DOS). It is found that the total
DOS at the Fermi-level for the heavily p-doped (Ga-face)GaN and ndoped
(Si-face)4H-SiC hetero-epitaxial system, with one layer of
(Al-face)AlN as the interface material, is comparatively higher than
that of the various cases studied, indicating that there could be good
vertical conduction across the (Ga-face)GaN over (Si-face)(0001)4HSiC
hetero-epitaxial material system.
Abstract: While computers are known to facilitate lower levels of learning, such as rote memorization of facts, measurable through electronically administered and graded multiple-choice questions, yes/no, and true/false answers, the imparting and measurement of higher-level cognitive skills is more vexing. These require more open-ended delivery and answers, and may be more problematic in an entirely virtual environment, notwithstanding the advances in technologies such as wikis, blogs, discussion boards, etc. As with the integration of all technology, merit is based more on the instructional design of the course than on the technology employed in, and of, itself. With this in mind, this study examined the perceptions of online students in an introductory Computer Information Systems course regarding the fostering of various higher-order thinking and team-building skills as a result of the activities, resources and technologies (ART) used in the course.
Abstract: This paper presents a novel method for prediction of
the mechanical behavior of proximal femur using the general
framework of the quantitative computed tomography (QCT)-based
finite element Analysis (FEA). A systematic imaging and modeling
procedure was developed for reliable correspondence between the
QCT-based FEA and the in-vitro mechanical testing. A speciallydesigned
holding frame was used to define and maintain a unique
geometrical reference system during the analysis and testing. The
QCT images were directly converted into voxel-based 3D finite
element models for linear and nonlinear analyses. The equivalent
plastic strain and the strain energy density measures were used to
identify the critical elements and predict the failure patterns. The
samples were destructively tested using a specially-designed gripping
fixture (with five degrees of freedom) mounted within a universal
mechanical testing machine. Very good agreements were found
between the experimental and the predicted failure patterns and the
associated load levels.
Abstract: In order to study the influence of different methods of controlling weeds such as mechanical weeding and mechanical weeder efficiency analysis in mechanical cultivation conditions, in farming year of 2011 an experiment was done in a farm in coupling and development of technology center in Haraz,Iran. The treatments consisted of (I) control treatment: where no weeding was done, (II) use of mechanical weeding without engine and (III) power mechanical weeding. Results showed that experimental treatments had significantly different effects (p=0.05) on yield traits and number of filled grains per panicle, while treatments had the significant effects on grain weight and dry weight of weeds in the first, second and third weeding methods at 1% of confidence level. Treatment (II) had its most significant effect on number of filled grains per panicle and yield performance standpoint, which was 3705.97 kg ha-1 in its highest peak. Treatment (III) was ranked as second influential with 3559.8 kg ha-1. In addition, under (I) treatments, 2364.73 kg ha-1 of yield produced. The minimum dry weights of weeds in all weeding methods were related to the treatment (II), (III) and (I), respectively. The correlation coefficient analysis showed that total yield had a significant positive correlation with the panicle grain yield per plant (r= 0.55*) and the number of grains per panicle-1 (r= 0.57*) and the number of filled grains (r= 0.63*). Total rice yield also had negative correlation of r= -0. 64* with weed dry weight at second weed sampling time (17 DAT). The weed dry weight at third and fourth sampling times (24 and 40 DAT) had negative correlations of -0.65** and r=-0.61* with rice yield, respectively.
Abstract: Formal Specification languages are being widely used
for system specification and testing. Highly critical systems such as
real time systems, avionics, and medical systems are represented
using Formal specification languages. Formal specifications based
testing is mostly performed using black box testing approaches thus
testing only the set of inputs and outputs of the system. The formal
specification language such as VDMµ can be used for white box
testing as they provide enough constructs as any other high level
programming language. In this work, we perform data and control
flow analysis of VDMµ class specifications. The proposed work is
discussed with an example of SavingAccount.
Abstract: Animated graph gives some good impressions in
presenting information. However, not many people are able to produce it because the process of generating an animated graph requires some technical skills. This work presents Content
Management System with Animated Graph (CMS-AG). It is a webbased system enabling users to produce an effective and interactive
graphical report in a short time period. It allows for three levels of user authentication, provides update profile, account management, template management, graph management, and track changes. The system development applies incremental development approach, object-oriented concepts and Web programming technologies. The design architecture promotes new technology of reporting. It also helps user cut off unnecessary expenses, save time and learn new things on different levels of users. In this paper, the developed system is described.
Abstract: Development of levels of service in municipal context
is a flexible vehicle to assist in performing quality-cost trade-off
analysis for municipal services. This trade-off depends on the
willingness of a community to pay as well as on the condition of the
assets. Community perspective of the performance of an asset from
service point of view may be quite different from the municipality
perspective of the performance of the same asset from condition
point of view. This paper presents a three phased level of service
based methodology for water mains that consists of :1)development
of an Analytical Hierarchy model of level of service 2) development
of Fuzzy Weighted Sum model of water main condition index and 3)
deriving a Fuzzy logic based function that maps level of service to
asset condition index. This mapping will assist asset managers in
quantifying condition improvement requirement to meet service
goals and to make more informed decisions on interventions and
relayed priorities.
Abstract: The two agro-ecological zones became the focus of
the study because of violent nature of the incessant conflict in the
zones. The available register of farmers association was the sampling
frame work where ten percent (61) farmers per state were randomly
sampled. Data were collected and analysed using z-test. The research
findings revealed tree crops and grains production enterprises ranked
higher in Osun (rain fed zones) and Taraba states (savannah zones)
respectively. Osun state entrepreneur felt the effect of the conflict on
their enterprises more than Tarba state. The reasons adduced for
severity of the conflict on enterprises are majority (77.0%) migrated
and (75.5%) of them were not allowed to enter their farms during and
when conflict deescalated unlike situation in Taraba state. The
different in enterprises production level between the two agroecological
zone was statistically significant at p