Abstract: In this research (using induction furnace process)
nodular iron with three different percentages of copper (residual,
0.5% and 1,2%) was obtained. Chemical analysis was performed by
mass spectrometry and microstructures were characterized by Optical
Microscopy (ASTM E3) and Scanning Electron Microscopy (SEM).
The study of mechanical behavior was carried out in a mechanical
test machine (ASTM E8) and a Pin on disk tribometer (ASTM G99)
was used to assess wear resistance. It is observed that the dissolution
of copper in crystal lattice increases the pearlite structure improving
the wear and hardness behavior, but producing a contrary effect on
the energy absorption.
Abstract: As the economies of other countries in the
Mediterranean Basin, the tourism sector in our country has a high
denominator in economics. Tourism businesses, which are building
blocks of tourism, sector faces with a variety of problems during their
activities. These problems faced make business efficiency and
competition conditions of the businesses difficult. Most of the
problems faced by the tourism businesses and the information of
consumers about consumers’ rights were used in this study, which is
conducted to determine the problems of tourism businesses in the
Central Anatolia Region. It is aimed to contribute the awareness of
staff and executives working at tourism sector and to attract attention
of businesses active concurrently with tourism sector and legislators.
Abstract: In this paper, we regard as a coded transmission over a
frequency-selective channel. We plan to study analytically the
convergence of the turbo-detector using a maximum a posteriori
(MAP) equalizer and a MAP decoder. We demonstrate that the
densities of the maximum likelihood (ML) exchanged during the
iterations are e-symmetric and output-symmetric. Under the Gaussian
approximation, this property allows to execute a one-dimensional
scrutiny of the turbo-detector. By deriving the analytical terminology
of the ML distributions under the Gaussian approximation, we confirm
that the bit error rate (BER) performance of the turbo-detector
converges to the BER performance of the coded additive white
Gaussian noise (AWGN) channel at high signal to noise ratio (SNR),
for any frequency selective channel.
Abstract: The aim of research was to define the relations
between volatile compounds, some parameters (pH, titratable acidity
(TA), total soluble solid (TSS), lactic acid bacteria count) and
consumer preference of commercial fermented milks. These relations
tend to be used for controlling and developing new fermented milk
product. Three leading commercial brands of fermented milks in
Thailand were evaluated by consumers (n=71) using hedonic scale
for four attributes (sweetness, sourness, flavour, and overall liking),
volatile compounds using headspace-solid phase microextraction
(HS-SPME) GC-MS, pH, TA, TSS and LAB count. Then the
relations were analyzed by principal component analysis (PCA). The
PCA data showed that all of four attributes liking scores were related
to each other. They were also related to TA, TSS and volatile
compounds. The related volatile compounds were mainly on
fermented produced compounds including acetic acid, furanmethanol,
furfural, octanoic acid and the volatiles known as artificial fruit
flavour (beta pinene, limonene, vanillin, and ethyl vanillin). These
compounds were provided the information about flavour addition in
commercial fermented milk in Thailand.
Abstract: The purpose of this presentation is to describe an interdisciplinary teaching program that integrates physical education concepts using a philosophical approach. The presentation includes a review of: a) the philosophy of American education, b) the philosophy of sports and physical education, c) the interdisciplinary physical education program, d) professional development programs, (e) the Success of this physical education program, f) future of physical education. This unique interdisciplinary program has been implemented in an urban school physical education discipline in East Orange, New Jersey for over 10 years.
During the program the students realize that the bodies go through different experiences. The body becomes a place where a child can recognize in an enjoyable way to express and perceive particular feelings or mental states. Children may distinguish themselves to have high abilities in the social or other domains but low abilities in the field of athletics.
The goal of this program for the individuals is to discover new skills, develop and demonstrate age appropriate mastery level at different tasks, therefore the program consists of 9 to 12 sports, including many game. Each successful experience increases the awareness ability. Engaging in sports and physical activities are social movements involving groups of children in situations such as teams, friends, and recreational settings, which serve as a primary socializing agent for teaching interpersonal skills. As a result of this presentation the audience will reflect and explore how to structure a physical education program to integrate interdisciplinary subjects with philosophical concepts.
Abstract: This paper proposes a mathematical model and
examines the performance of an exact algorithm for a location–
transportation problems in humanitarian relief. The model determines
the number and location of distribution centers in a relief network,
the amount of relief supplies to be stocked at each distribution center
and the vehicles to take the supplies to meet the needs of disaster
victims under capacity restriction, transportation and budgetary
constraints. The computational experiments are conducted on the
various sizes of problems that are generated. Branch and bound
algorithm is applied for these problems. The results show that this
algorithm can solve problem sizes of up to three candidate locations
with five demand points and one candidate location with up to twenty
demand points without premature termination.
Abstract: IEEE 802.16 (WiMAX) aims to present high speed
wireless access to cover wide range coverage. The base station (BS)
and the subscriber station (SS) are the main parts of WiMAX.
WiMAX uses either Point-to-Multipoint (PMP) or mesh topologies.
In the PMP mode, the SSs connect to the BS to gain access to the
network. However, in the mesh mode, the SSs connect to each other
to gain access to the BS.
The main components of QoS management in the 802.16 standard
are the admission control, buffer management and packet scheduling.
In this paper, we use QualNet 5.0.2 to study the performance of
different scheduling schemes, such as WFQ, SCFQ, RR and SP when
the numbers of SSs increase. We find that when the number of SSs
increases, the average jitter and average end-to-end delay is increased
and the throughput is reduced.
Abstract: The Blue Nile Basin is the most important tributary of
the Nile River. Egypt and Sudan are almost dependent on water
originated from the Blue Nile. This multi-dependency creates
conflicts among the three countries Egypt, Sudan, and Ethiopia
making the management of these conflicts as an international issue.
Good assessment of the water resources of the Blue Nile is an
important to help in managing such conflicts. Hydrological models
are good tool for such assessment. This paper presents a critical
review of the nature and variability of the climate and hydrology of
the Blue Nile Basin as a first step of using hydrological modeling to
assess the water resources of the Blue Nile. Many several attempts
are done to develop basin-scale hydrological modeling on the Blue
Nile. Lumped and semi distributed models used averages of
meteorological inputs and watershed characteristics in hydrological
simulation, to analyze runoff for flood control and water resource
management. Distributed models include the temporal and spatial
variability of catchment conditions and meteorological inputs to
allow better representation of the hydrological process. The main
challenge of all used models was to assess the water resources of the
basin is the shortage of the data needed for models calibration and
validation. It is recommended to use distributed model for their
higher accuracy to cope with the great variability and complexity of
the Blue Nile basin and to collect sufficient data to have more
sophisticated and accurate hydrological modeling.
Abstract: This article discusses issues related to the System of
Innovation: Comparing economies of Brazil and South Africa.
Having as this study aimed at comparing the Innovation System of
the countries mentioned. Then briefly describe the process of Venture
Capital and present the industry innovation in Brazil and South
Africa. The methodological approach described in this article is
descriptive and the approach is qualitative, taking as a basis
secondary data relating to research articles. The main results are
related to the different forms of financing of Venture Capital used by
countries compared, in addition to the training and economic policy.
And finally, it was highlighted the importance of implementation of
policy reforms for the Brazil and Africa in the innovation process.
Abstract: Remote sensing plays a vital role in mapping of
resources and monitoring of environments of the earth. In the present
research study, mapping and monitoring of clay siltations occurred in
the Alkhod Dam of Muscat, Sultanate of Oman are carried out using
low-cost multispectral Landsat and ASTER data. The dam is
constructed across the Wadi Samail catchment for ground water
recharge. The occurrence and spatial distribution of siltations in the
dam are studied with five years of interval from the year 1987 of
construction to 2014. The deposits are mainly due to the clay, sand
and silt occurrences derived from the weathering rocks of ophiolite
sequences occurred in the Wadi Samail catchment. The occurrences
of clays are confirmed by minerals identification using ASTER
VNIR-SWIR spectral bands and Spectral Angle Mapper supervised
image processing method. The presence of clays and their spatial
distribution are verified in the field. The study recommends the
technique and the low-cost satellite data to similar region of the
world.
Abstract: The objective of this study was to assess whether
living in proximity to a roofing fiber cement factory in southern
Thailand was associated with physical, mental, social, and spiritual
health domains measured in a self-reported health risk assessment
(HRA) questionnaire. A cross-sectional study was conducted among
community members divided into two groups: near population (living
within 0-2km of factory) and far population (living within 2-5km of
factory) (N=198). A greater proportion of those living far from the
factory (65.34%) reported physical health problems than the near
group (51.04%) (p =0.032). This study has demonstrated that the near
population group had higher proportion of participants with positive
ratings on mental assessment (30.34%) and social health impacts
(28.42%) than far population group (10.59% and 16.67%,
respectively) (p
Abstract: This study investigates the cleaning performance of
high intensity 360 kHz frequency on removal of nano-dimensional
and sub-micron particles from various surfaces, uniformity of the
cleaning tank and run to run variation of cleaning process. The
uniformity of the cleaning tank was measured by two different
methods i.e. 1. ppbTM meter and 2. Liquid Particle Counting (LPC)
technique. The result indicates that the energy was distributed more
uniformly throughout the entire cleaning vessel even at the corners
and edges of the tank when megasonic sweeping technology is
applied. The result also shows that rinsing the parts with 360 kHz
frequency at final rinse gives lower particle counts, hence higher
cleaning efficiency as compared to other frequencies. When
megasonic sweeping technology is applied each piezoelectric
transducers will operate at their optimum resonant frequency and
generates stronger acoustic cavitational force and higher acoustic
streaming velocity. These combined forces are helping to enhance the
particle removal and at the same time improve the overall cleaning
performance. The multiple extractions study was also carried out for
various frequencies to measure the cleaning potential and asymptote
value.
Abstract: Comparisons of financial development across
countries are central to answering many of the questions on factors
leading to economic development. For this reason this study analyzes
the implications of financial system’s development on country’s
economic development. The aim of the article: to analyze the impact
of financial system’s development on economic development. The
following research methods were used: systemic, logical and
comparative analysis of scientific literature, analysis of statistical
data, time series model (Autoregressive Distributed Lag (ARDL)
Model). The empirical results suggest about positive short and long
term effect of stock market development on GDP per capita.
Abstract: Nature is a great source of inspiration for solving
complex problems in networks. It helps to find the optimal solution.
Metaheuristic algorithm is one of the nature-inspired algorithm which
helps in solving routing problem in networks. The dynamic features,
changing of topology frequently and limited bandwidth make the
routing, challenging in MANET. Implementation of appropriate
routing algorithms leads to the efficient transmission of data in
mobile ad hoc networks. The algorithms that are inspired by the
principles of naturally-distributed/collective behavior of social
colonies have shown excellence in dealing with complex
optimization problems. Thus some of the bio-inspired metaheuristic
algorithms help to increase the efficiency of routing in ad hoc
networks. This survey work presents the overview of bio-inspired
metaheuristic algorithms which support the efficiency of routing in
mobile ad hoc networks.
Abstract: This paper describes the tradeoffs and the design from
scratch of a self-contained, easy-to-use health dashboard software
system that provides customizable data tracking for patients in smart
homes. The system is made up of different software modules and
comprises a front-end and a back-end component. Built with HTML,
CSS, and JavaScript, the front-end allows adding users, logging into
the system, selecting metrics, and specifying health goals. The backend
consists of a NoSQL Mongo database, a Python script, and a
SimpleHTTPServer written in Python. The database stores user
profiles and health data in JSON format. The Python script makes use
of the PyMongo driver library to query the database and displays
formatted data as a daily snapshot of user health metrics against
target goals. Any number of standard and custom metrics can be
added to the system, and corresponding health data can be fed
automatically, via sensor APIs or manually, as text or picture data
files. A real-time METAR request API permits correlating weather
data with patient health, and an advanced query system is
implemented to allow trend analysis of selected health metrics over
custom time intervals. Available on the GitHub repository system,
the project is free to use for academic purposes of learning and
experimenting, or practical purposes by building on it.
Abstract: Total hip replacement had been one of the most
successful operations in hip arthritis surgery. The purpose of this
research had been to develop a dynamic hip contact of Thai femoral
bone to analyze the stress distribution on the implant and the strain
distribution on the bone model under daily activities and compared
with the static load simulation. The results showed the different of
maximum von Mises stress 0.14 percent under walking and 0.03
percent under climbing stair condition and the different of equivalent
total strain 0.52 percent under walking and 0.05 percent under
climbing stair condition. The muscular forces should be evaluated
with dynamic condition to reduce the maximum von Mises stress and
equivalent total strain.
Abstract: Composite material based on Fe3Si micro-particles
and Mn-Zn nano-ferrite was prepared using powder metallurgy
technology. The sol-gel followed by autocombustion process was
used for synthesis of Mn0.8Zn0.2Fe2O4 ferrite. 3 wt.% of mechanically
milled ferrite was mixed with Fe3Si powder alloy. Mixed micro-nano
powder system was homogenized by the Resonant Acoustic Mixing
using ResodynLabRAM Mixer. This non-invasive homogenization
technique was used to preserve spherical morphology of Fe3Si
powder particles. Uniaxial cold pressing in the closed die at pressure
600 MPa was applied to obtain a compact sample. Microwave
sintering of green compact was realized at 800°C, 20 minutes, in air.
Density of the powders and composite was measured by
Hepycnometry. Impulse excitation method was used to measure
elastic properties of sintered composite. Mechanical properties were
evaluated by measurement of transverse rupture strength (TRS) and
Vickers hardness (HV). Resistivity was measured by 4 point probe
method. Ferrite phase distribution in volume of the composite was
documented by metallographic analysis.
It has been found that nano-ferrite particle distributed among
micro- particles of Fe3Si powder alloy led to high relative density
(~93%) and suitable mechanical properties (TRS >100 MPa, HV
~1GPa, E-modulus ~140 GPa) of the composite. High electric
resistivity (R~6.7 ohm.cm) of prepared composite indicate their
potential application as soft magnetic material at medium and high
frequencies.
Abstract: In this paper, we propose an automatic verification
technology of software patches for user virtual environments on IaaS
Cloud to decrease verification costs of patches. In these days, IaaS
services have been spread and many users can customize virtual
machines on IaaS Cloud like their own private servers. Regarding to
software patches of OS or middleware installed on virtual machines,
users need to adopt and verify these patches by themselves. This task
increases operation costs of users. Our proposed method replicates
user virtual environments, extracts verification test cases for user
virtual environments from test case DB, distributes patches to virtual
machines on replicated environments and conducts those test cases
automatically on replicated environments. We have implemented the
proposed method on OpenStack using Jenkins and confirmed the
feasibility. Using the implementation, we confirmed the effectiveness
of test case creation efforts by our proposed idea of 2-tier abstraction
of software functions and test cases. We also evaluated the automatic
verification performance of environment replications, test cases
extractions and test cases conductions.
Abstract: Human motion capture has become one of the major
area of interest in the field of computer vision. Some of the major
application areas that have been rapidly evolving include the
advanced human interfaces, virtual reality and security/surveillance
systems. This study provides a brief overview of the techniques and
applications used for the markerless human motion capture, which
deals with analyzing the human motion in the form of mathematical
formulations. The major contribution of this research is that it
classifies the computer vision based techniques of human motion
capture based on the taxonomy, and then breaks its down into four
systematically different categories of tracking, initialization, pose
estimation and recognition. The detailed descriptions and the
relationships descriptions are given for the techniques of tracking and
pose estimation. The subcategories of each process are further
described. Various hypotheses have been used by the researchers in
this domain are surveyed and the evolution of these techniques have
been explained. It has been concluded in the survey that most
researchers have focused on using the mathematical body models for
the markerless motion capture.
Abstract: With increasingly more mobile health applications
appearing due to the popularity of smartphones, the possibility arises
that these data can be used to improve the medical diagnostic process,
as well as the overall quality of healthcare, while at the same time
lowering costs. However, as of yet there have been no reports of a
successful combination of patient-generated data from smartphones
with data from clinical routine. In this paper we describe how these
two types of data can be combined in a secure way without
modification to hospital information systems, and how they can
together be used in a medical expert system for automatic nutritional
classification and triage.